DN4418BN – 18” Towel Bar
Brushed Nickel Finish
DN4424BN – 24” Towel Bar
Brushed Nickel Finish
DN4418CH – 18” Towel Bar
Chrome Finish
DN4424CH – 24” Towel Bar
Chrome Finish
DN4418ORB – 18” Towel Bar
Oil Rubbed Bronze Finish
DN4424ORB – 24” Towel Bar
Oil Rubbed Bronze Finish
25300 AL MOEN DRIVE NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321-8809 FAX: (800) 848-6636
INTERNATIONAL: (440) 962-2000 FAX: (440) 962-2726
CUSTOMER SERVICE (USA): 800-882-0116 FAX: (888) 379-2720
WWW.MOEN.COM
Copyright Creative Specialties International Literature # BA1519
Towel bar post is a die cast from the
highest quality zinc alloy (Zamac).
Casting is plated in chrome, brushed
nickel or oil rubbed bronze. Towel
bar is aluminum for brushed nickel
and chrome finishes and brass for oil
rubbed bronze.
Cleaning Instructions:
1. Position the mounting template on the wall in the desired location.
2. Using a level, align the template and tape it to the wall.
3. Drill two 5/16” holes at each mounting post location that corresponds to
your product.
4. Remove the template from the wall.
5. Fold ends of the plastic toggle together and insert into each hole in the
wall.
6. Lightly tap anchors until flush with the wall.
7. One at a time, insert plastic pin into each of the anchors and lightly tap
to activate anchor. Remove pin and repeat on all anchors.
8. Remove mounting posts from the product assemblies by loosening
each setscrew.
9. Place the mounting plate on the wall over the installed wall anchors
w ith “UP” facing you.
10. Insert screws through the mounting plate into the anchors. Tighten
the screws.
11. Assemble the towel bar and posts.
12. While assembled, position each end post with setscrews facing down
and place over both mounting posts. Tighten the setscrew at the
bottom of each post.
Stock Number:______________________Towel Bar
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
18” & 24” Towel Bar
DN4418 & DN4424
Vale™ Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
DN4408BN – Robe Hoook
Brushed Nickel Finish
DN4408CH – Robe Hook
Chrome Finish
DN4408ORB – Robe Hook
Oil Rubbed Bronze
25300 AL MOEN DRIVE NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321-8809 FAX: (800) 848-6636
INTERNATIONAL: (440) 962-2000 FAX: (440) 962-2726
CUSTOMER SERVICE (USA): 800-882-0116 FAX: (888) 379-2720
WWW.MOEN.COM
Copyright Creative Specialties International Literature # BA1518
Pivoting Paper Holder post is die
cast from highest quality zinc alloy
(Zamac). Casting is plated in chrome,
brushed nickel or oil rubbed bronze.
Cleaning Instructions:
1. Position the mounting template on the wall in the desired location.
2. Using a level, align the template and tape it to the wall.
3. Drill two 5/16” holes at each mounting post location that
corresponds to your product.
4. Remove the template from the wall.
5. Fold ends of the plastic toggle together and insert into each hole
in the wall.
6. Lightly tap anchors until flush with the wall.
7. One at a time, insert plastic pin into each of the anchors and
lightly tap to activate anchor. Remove pin and repeat on all
anchors.
8. Remove mounting posts from the product assemblies by
loosening each setscrew.
9. Place the mounting plate on the wall over the installed wall
anchors with “UP” facing you.
10. Insert screws through the mounting plate into the anchors. Tighten
the screws.
11. Place each assembly over the mounting posts with setscrews
facing down. Pivoting post with bar should be on the left side.
Tighten both setscrews.
Stock Number:______________________Pivoting
Paper Holder By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
Pivoting Paper Holder
DN4408
Vale™ Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
DN4486BN – Towel Ring
Brushed Nickel Finish
DN4486CH – Towel Ring
Chrome Finish
DN4486ORB – Towel Ring
Oil Rubbed Bronze
25300 AL MOEN DRIVE NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321-8809 FAX: (800) 848-6636
INTERNATIONAL: (440) 962-2000 FAX: (440) 962-2726
CUSTOMER SERVICE (USA): 800-882-0116 FAX: (888) 379-2720
WWW.MOEN.COM
Copyright Creative Specialties International Literature # BA1517
Towel Ring post is die cast from
highest quality zinc alloy (Zamac).
Casting is plated in chrome, brushed
nickel or oil rubbed bronze. Towel
Ring is aluminum for brushed nickel
and chrome finishes and brass for oil
rubbed bronze.
Cleaning Instructions:
1. Remove mounting posts from the product assemblies by
loosening each setscrew.
2. Position the mounting plate on the wall at desired location with
“UP” facing you. Mark hole locations.
3. Drill 2 holes as marked using 5/16” drill bit.
4. Fold ends of the plastic toggle anchor together and insert into
each hole in the wall
5. Lightly tap anchors until flush with the wall.
6. One at a time, insert plastic pin into each anchor and lightly tap
to activate anchor. Remove pin and repeat on other anchor.
7. Place the mounting plate on the wall over the installed wall
anchors with “UP” facing you.
8. Tighten screws.
9. Place decorative product over the mounting plate with the
setscrew facing down. Tighten setscrew.
Stock Number:______________________Robe Hook
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
Towel Ring
DN4486
Vale™ Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
-
1
-
2
-
3
Moen ValeCH3PC18 Instrukcja instalacji
- Typ
- Instrukcja instalacji
- Niniejsza instrukcja jest również odpowiednia dla
w innych językach
- English: Moen ValeCH3PC18 Installation guide
Powiązane artykuły
-
Moen DN0818ORB Instrukcja instalacji
-
-
-
-
-
-
-
Moen DN0790CH Specyfikacja
-
-
