RiteTemp 6022 Instrukcja instalacji

Marka: RiteTemp

Model: 6022

Kategoria: Termostaty

Typ: Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

6030

• Your thermostat is a precise instrument, handle it with care.

• Turn off electricity to the appliance before installing or

servicing thermostat or any part of the system. 

• Do not turn electricity back on until work is completed.

• Do not short (jumper) across electric terminals at control on

furnace or air conditioner to test the system. This will damage

the thermostat and void your warranty.

• All wiring must conform to local codes and ordinances.

• This thermostat is designed for use with 24 volt AC and

millivolt systems. The thermostat should be limited to a

maximum of 1.0 amps; higher amperage may cause damage

to the thermostat.

Caution

Install guide 6022

ENGLISH

HEAT

ARGET TEMP

PROGRAM

HOLD

COPY

REVIEW

FIL

TER

TIME SLOT

TIME SET

SET

CLOCK

PROG2

Location

Caution

Tools

To avoid electrical shock and to prevent damage to the furnace, air conditioner,

and thermostat, disconnect the power supply before beginning work.

This can be done at the circuit breaker, or at the appliance.

Replacement installations - mount the new thermostat in place of the old one.



New installations - follow the guidelines listed below.

• Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, and

in a room that is used often.

• Do not install it where there are unusual heating conditions, such as: in direct

sunlight; near a lamp, radio, television, radiator register, or fireplace; near hot

water pipes in a wall; near a stove on the other side of a wall.

• Do not locate in unusual cooling conditions, such as: on a wall separating an

unheated room; or in a draft from a stairwell,

door, or window.

• Do not locate in a damp area. This can

lead to corrosion that will shorten thermostat

life.

• Do not locate where air circulation is poor,

such as: in a corner or an alcove; or behind

an open door.

• Do not install the unit until all construction

work and painting has been completed.

• This thermostat does not require leveling.

You will need a small Phillips screwdriver and possibly a drill

with 3/16-in. (4.8mm) bit for wall mounting.

Good

5ft.

(1.5m)

PG 1

PG 2

Install guide 6022

Remove old unit

Prepare wires

IMPORTANT : LABEL ALL WIRES 

BEFORE DISCONNECTING THEM!

• Switch electricity to the furnace and

air conditioner OFF; then proceed with the

following steps.

• Remove cover from old thermostat. Most are

snap-on types and simply pull off. Some have

locking screws on the side or front. These must

be loosened. Note the letters printed near the terminals.

Attach labels (enclosed) to each wire for identification.

• Label the wires one at a time. You must label all the wires before

you proceed. With all wires labeled, remove them from the old unit.

• Make sure the wires do not fall back inside the wall. You can wind

them around a pencil to keep them from falling.

• Loosen all screws on the old thermostat and remove it from the wall.

• Fill wall opening with non-combustible insulation to prevent drafts.

PG 3

PG 4

Caution

Read instructions carefully before removing any wiring from existing thermostat.

Wires must be labeled before they are removed. THERE IS NO STANDARD

COLOR CODE. When removing wires from their terminals, ignore the color of

the wires since these may not comply with any standard.

• You will need at least 2.6" of wire for each

of your connections to the 6022.

• If you do not have enough wire, splice

additional wire to allow enough slack.

• Fan out wires below the hole as shown.

From W

all

Trim

2.6"

Before you Connect Wires

Caution

Do not allow wires to touch each other or parts on thermostat.

Please follow these guidelines for safe and secure

wire connections.

• Easy Terminals do not require stripping the wire.

• Clip any bare wire from previous installation.

• Take care not to damage the labels for each wire in handling.

• Fan wires out as illustrated with 6022 below the wall opening.

• Wires will dress behind the 6022 and up over the terminal area.

• Use the Step-By-Step diagram as your guide.

• Do not bunch wires behind 6022. Feed slack back into the wall opening.

• Connect labeled wires only to a terminal with corresponding letter.

• Insert the wire in the terminal and tighten

the screw securely.

• You will need to set Configuration

Jumpers per the Step-By-Step

diagram. A needle-nose plier may be

required to modify jumper positions

PG 5

PG 6

Determine which step-by-step wiring

diagram below you should use. Make

sure your wires are labeled. This may

require you to find the 'other end' connection for each wire on your heating or

air conditioning equipment and read the label there.

If you have a wire marked "C" it is optional. If you do connect it, the

thermostat will draw power from the C wire. This extends battery life.

What wires do you have?

Jumpers

From

Furnace

HEAT

ARGET TEMP

•

If you combination of wires is not above you can use the

wiring table on pages 24-25 to determine your connections,

or call our USA support line at 1-877-505-2353 for help.

• Find the referenece page with your wiring

diagram and jumper set-up information.

Remember, the C wire is optional.

Find the set-up diagram for your system

PG 7

PG 8

Go To Page 18Go To Page 17Go To Page 16

Go To Page 21

Go To Page 19

C W2 W Y Y2 RH G

2 stage Cool

2 stage Heat

From

Furnace

C W Y RH RC G

5 Wire

Heat/Cool

From

Furnace

C W Y RH G

4 Wire

Heat/Cool

From

Furnace

C W RH G

3 Wire

Heat

From

Furnace

From

Furnace

C W RH

2 Wire

Heat

From

Furnace

W RH A

3 Wire

Zoned

Hot Water

Go To Page 20

C B or O W2 Y RH G

5 Wire

Heat Pump

w/ Aux Heat

From

Furnace

C B or O Y RH G

4 Wire Heat Pump

w/o Aux Heat

From

Furnace

Go To Page 15

AGE

WIRES

Install AAA Batteries

• The 6022 requires 2 AAA batteries to operate .

• Switch MODE switch to OFF and the FAN switch to AUTO.

• Install 2 AAA alkaline batteries according to the polarity noted in

the compartment. LCD segments will go on.

• Press the RESET button (under top cover) to clear transient

program memory. NOTE: Replace the batteries when this LOW

battery indicator appears on the display or once a year.

• Replace top and bottom covers on unit.

Wall

Wires

6022

Wall anchor

• Hold the 6022 against the wall, with the wires coming over

the top above terminal block. The 6022 will cover the hole

in the wall.

• Position 6022 for best appearance. Use the optional stand-

offs if more space for wires is needed behind the 6022.

• Attach the base to the wall with the screws provided.

• If you are mounting the base to sheet rock or if you are

using the old mounting holes, use the plastic anchors

provided. Drill a 3/16-in.(4.8mm) hole for

the insert at each screw location, then

mount the base.

Mount the 6022

HEAT

ARGET TEMP

AAA

HEAT

ARGET TEMP

NOTE: If you have labeled your wires, follow the correct Step-By-Step, and

these Check procedures do not operate your system call support at 

1-877-505-2353

Check Unit

Follow these procedures to verify you

have correctly installed the 6022.

To check Fan: (If you connected the

G wire - fan relay)

• Switch the FAN switch to the ON

position. Verify that air is blowing from

the system. Return to AUTO position

for normal operation.

To check HEAT mode:

Set the mode switch to HEAT.

Set the fan switch AUTO.

• Using the TEMP + button raise the Target Temp to 90deg. 

Allow the system 2 min to respond.

• Verify that heat is blowing from the system.

To check COOL mode:

• Set the mode switch to COOL.

• Press the TEMP - button to a temp 5 degrees below the room temp.

Allow the system 2 minutes to respond.

• Verify that cool air is blowing from the system.

Congratulations, you have successfully installed your unit.

Please proceed to the OPERATING Guide to initialize the 6022.

HEAT

TARGET TEMP

PROGRAM

HOLD

COPY

REVIEW

FIL

TER

TIME SLOT

TIME SET

SET

CLOCK

EPA

PROG2

TEMP

UP button

TEMP

DOWN button

Temperature

Display

Mode

Switch

Fan

Switch

HEAT

COOL

OFF

FAN

AUTO

BATTERIES ONLY - This thermostat can run on batteries only using 2AAA

alkaline batteries. The batteries will last at least 1 year; replace the batteries

once a year or when the low battery icon comes on the display. If the batteries

are not replaced, the thermostat will shut off the HVAC and then stop working.

24VAC - This thermostat can run on the HVAC 24VAC (C wire) if available.

As shown in the wiring diagrams, the C wire is the other side of the 24VAC

heating transformer and can be found where the other thermostat wires

connect at the wall or at the furnace. Do not use the common or ground side

of the line voltage. If the C wire is used, the batteries are then for back-up in

case of power loss only and will last much longer. With the C wire connected,

the thermostat will continue to work if the batteries die or are removed.

Power Options

NOTE:Your thermostat comes from the factory calibrated to +/- 1

of actual

temperature. It is an accurate instrument. If you want your thermostat to

display the same temperature as another thermometer in your home, you

can adjust its calibration.

To change the calibration:

Open Key pad door.

Locate the TIME SET button and press it. The

current calibration factor (+/-) of the 6022 will appear

in the LCD display as well as the modified temp.

Push the UP or DOWN arrows until the desired

calibration factor is reached.

Press HOME to save. The new calibrated temperature

will be displayed on the LCD.

Calibration

PROGRAM

HOLD

COPY

REVIEW

FIL

TER

TIME SLOT

TIME SET

SET

CLOCK

EPA

PROG2

Calibrate button

2 WIRE HEAT Heating GAS MILLIVOLT or 24vac

NOTE: Wires marked with

dotted line are optional.

PG 16

3 Wire Heat

6022

GAS Milivolt Heat

C B O W W2 Y Y2 RH RC G A

6022

R G

HVAC SYSTEM

C B O W W2 Y Y2 RH RC G A

STEP 1 - Connect the R (or RH) wire to the RH terminal on

the 6022. This connects the Heater Power to the thermostat.

STEP 2 - Connect the W wire to the W on the 6022.

This connects the heater control line to the 6022.

STEP 3 - Set Config jumpers per this diagram.

Your Heater is now connected to the 6022.

Please Return To Page 9

STEP 1 - Connect the R (or RH) wire to the RH terminal

on the 6022. This connects to the Heater Power .

STEP 2 - Connect the W wire to the W terminal on the

6022. This connects the heater control line to the 6022.

STEP 3 - Connect the G wire to the G terminal on the

thermostat. This connects the Fan to the 6022

STEP 4 - Set Config jumpers per this diagram. If you

have Electric heat set 7, if you have Gas or Oil set 5.

Your system is now connected to the 6022.

Please Return To Page 9

OPTIONAL POWER

WIRES WIRES

SET JUMPERS

1 2 3

STEP 1 - Connect the W wire to the W terminal on the

thermostat. This connects to the heater control line.

STEP 2 - Connect the Y wire to the Y terminal on the

6022. This connects to the Cooler compressor.

STEP 3 - Connect the RH wire to the RH terminal and the

RC wire to the RC terminal on the 6022. This connects

the Heater and Cooler Power.

STEP 4 - Connect the G wire to the G terminal on the

Thermostat. This connects to the Fan.

STEP 5 - Set Config jumpers per this diagram. If you

have Electric heat set 7, if you have Gas or Oil set 5.

Your HVAC system is now connected

to the 6022.

Please Return To Page 9

STEP 1 - Connect the W wire to the W terminal on the

thermostat. This connects to the heater control line.

STEP 2 - Connect the Y wire to the Y terminal on the

6022. This connects to the Cooler compressor.

STEP 3 - Connect the RH or R wire to the RH terminal on

the thermostat. This connects the Heater/Cooler Power.

STEP 4 - Connect the G wire to the G terminal on the

Thermostat. This connects to the Fan.

STEP 5 - Set Config jumpers per this diagram. If you

have Electric heat set 7, if you have Gas or Oil set 5.

Your HVAC system is now connected

to the 6022.

Please Return To Page 9

W Y RH G

PG 17

4 Wire Heat/Cool

6022

Terminals

R G

HVAC SYSTEM

C B O W W2 Y Y2 RH RC G A

OPTIONAL POWER

WIRES

W Y RH RC G

PG 18

5 Wire Heat/Cool

6022

Terminals

RH RC

HVAC SYSTEM

C B O W W2 Y Y2 RH RC G A

OPTIONAL

WIRES

1 2 3

SET JUMPERS

1 2 3

STEP 1 - Connect O wire to the O terminal or B wire to the B terminal on

the 6022. (If you have both O and B - connect O wire to O terminal 

DO NOT connect B to B terminal - see pg 24 Trane for B wire terminal) 

This connects the change-over valve.

STEP 2 - Connect the Y wire to Y on the 6022.

This connects the Compressor.

STEP 3 - Connect the R wire to RH on the 6022.

This connects to the 24vac power.

STEP 4 - Connect the G wire to the G terminal on the

6022. This connects the Fan.

STEP 5 - Set Config jumpers per this diagram.

Your HVAC system is now connected

to the 6022.

  Please Return T o Page 9

O Y R G

4 Wire Heat Pump w/o Aux

OPTIONAL POWER

WIRES

STEP 1 - Connect O wire to the O terminal or B wire to the B terminal on

the 6022. (If you have both O and B -connect O wire to O terminal DO NOT

connect B to B terminal - see pg 24 Trane for B wire terminal)

STEP 2 - Connect the W2 wire to W2 on the 6022.

STEP 3 - Connect the Y wire to Y on the 6022.

STEP 4 - Connect the R wire to RH on the 6022.

STEP 5 - Connect the G wire to G on the 6022.

STEP 6 - Set Config jumpers per this diagram.

Set jumper 1 if you have Gas or Oil aux heat.

Your HVAC system is now connected

to the 6022.

  Please Return T o Page 9

O W2 Y RH G

5 Wire Heat Pump w/ Aux Heat

WIRES

6022

Terminals

R G

HEAT PUMP SYSTEM

C B O W W2 Y Y2 RH RC G A

SET JUMPERS

6022

Terminals

R G

HEAT PUMP SYSTEM

C B O W W2 Y Y2 RH RC G A

OPTIONAL POWER

1 2 3

R A

Motor Valve

C B O W W2 Y Y2 RH RC G A

PG 22

W RH [A?] 3 Zoned Hot Water - Motor Valve

Step 1 - based on your valve type

Motor driven Valve- Connect the R (or RH) wire to the RH

terminal on the 6022. Connect the W wire to the W terminal

on the 6022. Connect the remaining wire to the A terminal.

Solenoid valve -Connect the R (or RH) wire to the RH

terminal on the 6022. Connect the W wire to the A terminal

on the 6022. Connect the remaining wire to the W terminal.

STEP 2 - Set Config jumpers per this diagram.

Your system is now connected to the 6022.

Please Return To Page 9

WIRES

STEP 1 - Connect the W wire to the W terminal and W2 to

W2 on the 6022. This connects 2 stages of heat.

STEP 2 - Connect the Y wire to the Y terminal and Y2 wire

to Y2 on the 6022. This connects 2 stages of cool.

STEP 3 - Connect the RH or R wire to the RH terminal on

the thermostat. This connects the Heater/Cooler Power.

STEP 4 - Connect the G wire to the G terminal on the

Thermostat. This connects to the Fan.

STEP 5 - Set Config jumpers per this diagram. If you

have Electric heat set 7, if you have Gas or Oil set 5.

Your HVAC system is now connected

to the 6022.

Please Return To Page 9

W2 W Y Y2 RH RC G

PG 21

2 Stage Heat and Cool

6022

Terminals

6022

Terminals

W Y

HVAC SYSTEM

C B O W

W Y Y2 RH RC G A

OPTIONAL

POWER

WIRES

SET JUMPERS

1 2 3

SET JUMPERS

1 2 3

This thermostat can be used with all millivolt and 24VAC heating and cooling systems. It

cannot be used with line voltage systems. This thermostat is digital and your desired heat or

cool temperatures can easily be set on the large screen with the +/- buttons on the front. A

minimum 4 minute off time protects heating and cooling systems from damage. 

This thermostat uses a new technique called sequential staging for more comfort with

faster reaction to requested temperature changes. When using a heat pump with Aux heat, if

the heat pump cannot keep up and/or is

defective, remove jumper from position 8 and put

jumper on position 6 and the Aux heat will then

be your only source of heat. Be sure to restore it

to PUMP when the pump is again operational as

aux heat is more expensive than pump heat.

6022 Features

Wire Reference

Your Wires Ritetemp Terminal

R or V or V R RH and RC Single power for HEA T and COOL

RH or 4    RH Power for HEAT (RH not connected to RC)

RC   RC Power for COOL (RH not connected to RC)

W   W Heat control

W2   W2 2nd stage HEAT or heat pump auxiliary heat

?    A 3rd wire for zoned hot water heat (see zoned)

Y   Y COOL control

Y2   Y2 2nd stage COOL control

G or F  G FAN control

C or X  C Common 24VAC power (to power thermostat)

E   Emergency heat (do not connect, tape of f)

L   System monitor (do not connect, tape of f)

T   Outdoor sensor (do not connect, tape of f)

B or   B Heat pump changeover (cool to heat, powered in heat)

O   O Heat pump changeover (heat to cool, powered in cool)

B and O  SEE NOTE 

B and O

NOTE: If

there are both

B and O wires

(Trane pump

products)

DO NOT

CONNECT B

to B terminal,

connect B to C

terminal

HEAT

TARGET TEMP

PROGRAM

HOLD

COPY

REVIEW

FIL

TER

TIME SLOT

TIME SET

SET

CLOCK

EPA

PROG2

Wire Reference cont

Your Wires Ritetemp Terminal



Lennox Heat Pump

V or VR or R RH

M or Y  Y

Y or W or W2 W2

F or G  G

R or O  O

X or X2 or C C

Trane Products [American Standard]

B  C

W or W1 W2

Zoned Systems

Your Wires Ritetemp Terminal

2 wire Zoned Hot Water

R    R

W    W

3 Wire Zoned Hot Water

Motor Driven Valves

R    R

W    W

Y (the 3rd wire)A

3 Wire Zoned Hot Water

Solenoid Valves

R    R

W    A

Y (the 3rd wire) W

SINGLE

POWER(R)

PUMP AUX

ELECT

RESET UNIT

CELSIUS

GAS/ELEC HEAT

OPEN

321

POWER RH

POWER RC

OPEN

PUMP AUX

GAS OR OIL

FAHRENHEIT

AFTER CHANGING JUMPERS

GAS OR OIL

ELECTRIC

CLOSED

HEAT

OR PUMP

CLOSED

CELSIUS

TYPE

AUX

FAHRENHEIT

HVAC

POWER

PUMP/

NORMAL

HP-AUX

ONLY

12 hr

24hr

12hr clock

24hr clock

HEAT

PUMP

HP-AUX

ONLY

NORMAL

SELECT

PG 25

PG 26

Jumper Reference

Configuration jumpers allow your

6022 to be adapted to many

different HVAC control

1611-020

Customer Support: 877-505-2353 or

Visit our website www.ritetemp-thermostats.com

HEAT

TARGET TEMP

PROGRAM

HOLD

COPY

REVIEW

FIL

TER

TIME SLOT

TIME SET

SET

CLOCK

EPA

PROG2

RiteTemp 6022 Instrukcja instalacji

Marka: RiteTemp

Model: 6022

Kategoria: Termostaty

Typ: Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

6030

ściągnij PDF

raport

w innych językach

English: RiteTemp 6022 Installation guide

RiteTemp 6022 Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

RiteTemp 6022 Instrukcja instalacji

w innych językach

Powiązane dokumenty

Inne dokumenty