307-007
Install guide 8029B
Customer Support: 888-515-2585 or
Visit our website www.ritetemp-thermostats.com
HE
AT
COOL
A
UTO
ON
OF
F
FAN
HE
AT
COOL
A
UTO
ON
O
F
F
F
A
N
ROO
M
TEMP
R
O
O
M
T
EM
P
Install guide 8029B
1 Location
Caution
Tools
To avoid electrical shock and to prevent damage to the furnace, air conditioner,
and thermostat, disconnect the power supply before beginning work.
This can be done at the circuit breaker, or at the appliance.
C A U T I O N
Your thermostat is a precise instrument.
Please handle it with care.
Turn off electricity to the appliance before installing or
servicing thermostat or any part of the system. Do not
turn electricity back on until work is completed.
Do not short (jumper) across electric terminals at
control on furnace or air conditioner to test the system.
This will damage the thermostat and void your warranty.
All wiring must conform to local codes and ordinances.
This thermostat is designed for use with 24 volt AC and
millivolt systems. The thermostat should be limited to a
maximum of 1.0 amps; higher amperage may cause
damage to the thermostat.
On replacement installations, mount the new thermostat in place of the
old one if possible.
On new installations, follow the guidelines listed below.
Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the
floor, and in a room that is used often.
Do not install it where there are unusual heating conditions, such as: in
direct sunlight; near a lamp, radio, television, radiator register, or
fireplace; near hot water pipes in a wall; near a stove on the other side
of a wall.
This thermostat does not require leveling.
Do not locate in unusual cooling conditions, such as: on a wall separating
an unheated room; or in a draft from a stairwell, door, or window.
Do not locate in a damp area. This can lead to corrosion that will shorten
thermostat life.
Do not locate where air circulation is poor, such as: in a corner or an
alcove; or behind an open door.
Do not install the unit until all construction work and painting has been
completed.
You will need #1 Phillips screwdriver (small) and
Drill with 3/16-in. (4.8mm) bit for this installation.
Good
5ft.
(1.5m)
PG 1
PG 2
2 Remove old unit
IMPORTANT : LABEL ALL WIRES
BEFORE DISCONNECTING THEM!
3 Mount the 8029B
Switch electricity to the furnace and
air conditioner OFF;
then proceed with the following steps.
Remove cover from old thermostat. Most are snap-on types
and simply pull off. Some have locking screws on the side
or front. These must be loosened. Note the letters printed
near the terminals. Attach labels (enclosed) to each wire for
identification.
Label the wires one at a time. You must have all the wires labeled
before you proceed. With all wires labeled, remove them from the old unit.
Make sure the wires do not fall back inside the wall.
Wind them around a
pencil to keep them from falling.
Loosen all screws on the old thermostat and remove it from the wall.
Fill wall opening with non-combustible insulation to prevent drafts.
Separate front from back of unit. Press up on the
catch on bottom of thermostat and swing the body
away from the base, lift up to remove the body from
the base.
Hold the base against the wall, with the wires
coming through the opening below the terminal block.
Position the base for best appearance. Use
the optional wall plate to cover blemishes
on wall from your old thermostat.
Attach the base to the wall with the two
screws provided.
If you are mounting the base to sheet rock
or if you are using the old mounting holes,
use the plastic anchors provided. Drill a
3/16-in.(4.8mm) hole for the insert at each
screw location, then mount the base.
PG 3
PG 4
B
G
W
Caution
C
R
C
O
B
RH
W
Y
G
H
E
A
T
C
O
O
L
AU
T
O
O
N
O
F
F
F
AN
Read instructions carefully before removing any wiring from existing thermostat.
Wires must be labeled before they are removed. THERE IS NO STANDARD
COLOR CODE. When removing wires from their terminals, ignore the color of the
wires since these may not comply with the standard.
C
R
C
O
B
R
H
W
Y
G
Terminal
Block
Wall Plate
Thermostat Base
R
O
O
M
T
E
M
P
4 Before you Connect Wires
Caution
Do not allow wires to touch each other or parts on thermostat.
Wires must be routed through the hole in the back plate, below the
terminal block, or they will hit parts on the cover.
Please follow these guidelines for safe and secure wire connections.
Determine which step-by-step wiring diagram you should use. Make sure your
wires are labeled. This may require you to find the 'other end' connection for each
wire on your heating or air conditioning equipment and read the label there.
If you have a wire marked "C" its connection is optional. If you do connect it the
thermostat will draw power from the C wire and this will extend battery life.
Optional Wire Connections
What Wires Do you Have?
Strip insulation 3/8 in. (9.5mm) from wire ends.
Take care not to damage the labels for each wire in handling.
Connect labeled wires only to a terminal with corresponding letter.
Bend the wire slightly, insert the wire under the contact plate and
tighten the screw down onto the wire.
PG 6
PG
5
RH
G
Y
W
C
F
rom
F
urnace
An
d AC unit
R
or
B
G
Y
R
C
F
rom
s
ingle stag
e
hea
t pum
p
O
or
RC
G
Y
W
C
F
rom
F
urnace
An
d AC unit
RH
Go To Page 13
Go To Page 14
Go To Page 12
RH
W
C
F
rom
F
urnace
G
W
RH
R
or
F
rom
F
urnace
Go To Page 11
C
Go To Page 15
R - Single source power for heat/cool
Note: R connects to both RC and RH using the red jumper
RH or R - HEATING POWER
RC - COOLING POWER
W - HEATING CONTROL
G - FAN RELAY
C - Common side of Heating Power
Y - COMPRESSOR
O - DAMPER OR CHANGEOVER VALVE (POWERED IN COOL)
B - DAMPER OR CHANGEOVER VALVE (POWERED IN HEAT)
or R
H
E
A
T
C
O
O
L
A
U
TO
O
N
OFF
F
A
N
When you have finished making connections. Hook
the top of the body onto the base, swing the body
down, and snap the body onto the base.
5 Install Batteries
6 Check Unit
The 8029B requires 2 AA batteries to operate your
furnace and retain its programmed temperature in
memory.
Switch MODE switch to OFF and
the FAN switch to AUTO.
Remove the control unit from the wall unit. Install 2
AA alkaline batteries according to the polarity noted
in the compartment. Initially, all LCD segments will
go on.
Press the RESET button to clear transient program memory.
NOTE: Replace the batteries when this LOW battery indicator
appears on the display or once a year. When replacing batteries,
you have 30 seconds before your custom program is lost.
Follow these procedures to verify you have correctly installed the unit.
To check HEAT mode:
Set the mode switch to HEAT. Set the fan
switch AUTO.
Using the TEMP UP button raise the set point
to 90deg allow the system 2 min to respond.
Verify that heat is blowing from the system.
To check COOL mode:
Set the mode switch to COOL.
Press the TEMP DOWN button to a temp 5
degrees below the room temperature.
Allow the system 2 minutes to respond.
Verify that cool air is blowing from the system.
To check Fan: (If you connected the G wire - fan relay)
Switch the FAN switch to the ON position. Verify that air is blowing from
the system. Return to AUTO position for normal operation.
TEMP
UP button
TEMP
DOWN button
Temperature
Display
Mode
Switch
Fan
Switch
PG 7
PG 8
C
RC
O
B
RH
W
Y
G
HE
A
T
COOL
A
U
T
O
ON
O
F
F
F
AN
AA
AA
R
OOM
T
EM
P
ROOM
T
E
M
P
NOTE: If you have an electric furnace system and the blower does not
operate after installation, remove the thermostat, turn it over, and find the
electric/gas heat selector jumper on the back of the control unit.
Switch it to "Elect"(see Diag below).
1) The 8029B can run on batteries only. (2AA Alkaline) 24VAC and MV
The batteries will last well over 1 year. If the batteries are not replaced the
thermostat will stop working.
2) The 8029B can run on the C wire if available.
24VAC ONLY
As shown in the wiring diagrams, The C wire is the other side of the 24VAC
heating transformer. If the C wire is used, the batteries are then for AC power
loss only and will last much longer. The thermostat will continue working if the
batteries die.
7 Power Options
6 Check Unit cont.
Congratulations, you have successfully installed your unit. Please
proceed to the OPERATING Guide to initialize the new thermostat.
PG 9
PG 10
Inside of Unit
GAS
ELECT
AA
AA
Fahrenheit
/Celsius jumper
Gas/Electric jumper
OFF ON
ADJ RM TEMP
NOTE:Your thermostat comes from the factory calibrated to +/- 1
o
of actual
temperature. It is an accurate instrument. If you want your thermostat to display
the same temperature as another thermometer in your home, you can adjust its
calibration.
To change the calibration:
Access the circuit board inside the thermostat.
Locate the calibration switch and
slide it to the ON position. The
current calibration of the
thermostat will appear in the
LCD display on the front.
Push the UP or DOWN arrows
until the desired temperature is
reached.
Slide the Calibration switch to
the OFF position. The new
calibration will be saved.
Calibration switch
8 Calibration
OPEN F
SHORT C
PG
11
PG
12
STEP 1 - Connect the R (or RH) wire to
the RH terminal on the thermostat.
This connects the Heater Power to the
thermostat.
STEP 2 - Connect the W wire to the W
terminal on the thermostat.
This connects the heater control line to the thermostat.
Your Heater is now connected to the thermostat.
STEP 1 - Connect the R (or RH) wire
to the RH terminal on the thermostat.
This connects to the Heater Power .
STEP 2 - Connect the W wire to the
W terminal on the thermostat.
This connects the heater control line
to the thermostat.
STEP 3 - Connect the G wire to the G
terminal on the thermostat.
This connects the Fan to the thermostat.
Your system is now connected to the thermostat.
Return To Page 7
Return To Page 7
2 WIRE Heating
(GAS MILLIVOLT or 24vac
NOTE: Wires marked with the dotted line are optional.
NOTE: Wires marked with the dotted line are optional.
3 WIRE
FURNACE
jumper
wire
Heat
Power
Heat
W G
RH
C
FAN
Thermostat
jumper
wire
FURNACE
HEAT
Thermostat
R
W
C
HEAT
Power
W
RH
R
or
From Fur
nace
C
RH
W
C
F
rom
F
urnace
G
or R
PG
14
PG
13
F
rom
F
urnace
and
AC unit
G
W
Y
RH
RC
C
R
G
Y
W
C
RH
or
From Fur
nace
and AC uni
t
STEP 1 - Connect the Y wire to the
Y terminal on the thermostat. This
connects to the Cooler compressor.
STEP 2 - Connect the RH or R wire
to the RH terminal on the thermostat.
This connects the Heater/Cooler
Power.
STEP 3 - Connect the W wire to the W terminal on the
thermostat. This connects to the heater control line.
STEP 4 - Connect the G wire to the G terminal on the
Thermostat. This connects to the Fan.
Your HVAC system is now connected to the thermostat.
STEP 1 - Remove the red
Jumper wire.
STEP 2 - Connect the Y wire to the
Y terminal on the thermostat. This
connects to the Cooler compressor.
STEP 3 - Connect the RH wire to the
RH terminal on the thermostat. This
connects to the Heater Power .
STEP 4 - Connect the RC wire to the RC terminal on
the thermostat. This connects to the Cooling Power .
STEP 5 - Connect the W wire to the W terminal on the thermostat.
This connects to the heater control line.
STEP 6 - Connect the G wire to the G terminal on the Thermostat.
This connects to the Fan.
Your HVAC system is now connected to the thermostat.
Return To Page 7
Return To Page 7
5 WIRE
4 WIRE
NOTE: Wires marked with the dotted line are optional.
NOTE: Wires marked with the dotted line are optional.
HVAC SYSTEM
jumper
wire
Heat
Power
Heat
W
G
RH
C
FAN
Y
Cool
Comp
Thermostat
HVAC SYSTEM
Remove
jumper
wire
HEAT
Power
Heat
W
G
RHRC
C
FAN
Y
Cool
Comp
COOL
Power
Thermostat
PG
15
STEP 1 - Connect the G wire to the G
terminal on the thermostat.
This connects the Fan.
STEP 2 - Add a jumper wire between
W and Y.
STEP 3 - Connect the Y wire to the Y
terminal on the thermostat.
This connects the Compressor.
STEP 4 - Connect the O or B wire to the O or B terminal
on the thermostat. (If you have both O and B contact
Ritetemp or your local HVAC contractor for further help)
This connects the change over valve.
STEP 5 - Connect the R wire to the RC terminal.
This connects to the 24vac power.
Your HVAC system is now connected to the thermostat.
Return To Page 7
SINGLE STAGE
HEAT PUMP
NOTE: Wires marked with
dotted line are optional.
From Fur
nace
and AC uni
t
R
G
Y
C
O
or
B
O or B
Single Stage HEAT PUMP
Change
Over
G
O or B
R
C
FAN
Y
Comp
24VAC
Power
jumper
wire
jumper
wire
Thermostat
The 8029B can be used with most 24 volt gas, oil or electric heating and air
conditioning systems, single-stage heat pumps or gas millivolt heating systems. It
cannot be used with 120 volt heating systems or multistage heat pumps. Ask The
Home Depot for other thermostats to control those systems.
The 8029B is digital. You can program your
desired Heat and cool temperature set points
directly on the Large LCD display.
You can easily override the set temperatures.
4-minute minimum off time in COOL protects
your air conditioning system from being
damaged.
Two "AA" batteries (not included) are used to retain
your time and temperature programs, and to run the thermostat.
8029B Features
PG 16
H
E
A
T
C
O
O
L
AU
T
O
O
N
O
F
F
F
A
N
R
O
O
M
TE
M
P
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
w innych językach
- English: RiteTemp 8029B
Powiązane dokumenty
Inne dokumenty
-
ControlTemp Basic Tamper Proof Thermostat Instrukcja obsługi
-
Filtrete 3M-50 Instrukcja instalacji
-
Intermatic CA8900 Instrukcja obsługi
-
3M 3M-30 Install Manual
-
Filtrete 3M-22 Instrukcja obsługi
-
Sharper Image Honeywell® Lyric T5+ Wi-Fi Smart Thermostat Instrukcja obsługi
-
Hunter 44378 Instrukcja instalacji
-
Honeywell Home THP9045A1098 Instrukcja obsługi
-
Alarm.Com PanelKit Instrukcja obsługi
-
AirCycler FRV Installation & User Manual
