UCR
Control Box for Robot
INSTRUCTION MANUAL
Packing List
Either Ref. UCR245-5A or Ref. UCR470-5A is included in UCR box:
Manual ........................... 1 unit
Ref. 0027876
Tool Cable 3m ............... 1 unit
Ref. 0027924
Communications
Cable 3m ........................ 1 unit
Ref. 0024563
Control Box for Robot .............................................................. 1 unit
Power Cord 1.5m ......... 1 unit
Ref. 0023714 (230 V)
Functions
*Download the Robot Communication Protocol for UCR unit at www.jbctools.com/jbcsoftware.html
There are up to 44 functions* to control the station, such as:
- Temperature Control
- Sleep and Hibernation Control
- Station Status
- Error Information
- Counters (Working Time, Sleep, Hibernation...)
This manual corresponds to the following references:
- UCR245-5A
- UCR470-5A
2
Trouble shooting
In case of error, a red light flashes a certain number of times, indicating an error number as shown in
the table below:
If the error persists, contact with JBC technical service.
Features
Fuse
Equipotencial
Connector
Power Socket
Main Switch
Tool Connector Communications Connector
LED Indicator *
Nº Error Description Solution
1 times Short-circuit Replace Cartridge
2 times Open circuit Replace Cartridge
3 times Tool not accepted Check if the tool is compatible with the Contron Box
4 times Tool detection error Check the tool
6 times Current usage leads to overloading Due to overload wait until the device has cooled down
7 times Short-circuit Check if the cartridge is compatible with the Control Box
12 times Memory error Reset the Control Box
*LED Indicator:
· Blue: equipment powered
· Green: equipment working
· Red blinking: error. See table
below for more info.
www.jbctools.com
3
1 3
5
2 4
Transmitted data - Grey cable
Optional:
Pedal activation by
relay or digital output
Ground - Blue cable
Brown cable
Black cable
Received data - White cable
DB9
Connector
5
4
9
8
7
6
3
2
1
Connection
- UCR can be connected to a PLC by a five-pin Communications Cable (Ref.
0020261).
- For a proper connection, it is necessary to connect only three cables to the corresponding 3 pins
at a typical DB9 male connector (PLC or computer).
- Download the Robot Communication Protocol at www.jbctools.com
Communications Cable
Ref. 0020261
For detailed information about pin distribution see following table:
Front view
UCR Communications Connector
Pin Distribution
Pin Color Description
1 Brown Not used
2 White Serial input: RS232 RX
3 Blue Common reference:
GND for RS232 and witch
4 Black Switch input: 0V or 24V to start feeding.
Leave it open to stop
5 Grey Serial output: RS232 TX
4
Control
Box
Cartridge Range Soldering Irons Cartridge Stand
R245 R470 TR245 TR470 TRA245 TRA470 CS2R245 CS2R470
UCR245
UCR470
SFR, GSFR and CLR are compatible with R245 and R470 cartridge ranges.
Compatibility
UCR can be used with both solderin irons, TR and TRA, and its cartridge ranges R245 and R470
respectively. Connect any of those soldering irons with the provided tool cable (Ref. 0027924). See the
table below to check the compatibility of the devices.
Ref. TR245-A/ TR470-A Ref. TRA245-B/ TRA470-B
www.jbctools.com
5
mm
(in)
162
6,378
74,30
2,925 210,50
8,287
76
2,992
151,50
5,965
11,50
0,453
39
1,535
43
1,693
43
1,693
4 x M4 max. depth 12
(4 x M4 max. depth 0,472)
UCR245-5A / UCR470-5A
CONTROL UNIT FOR AUTOMATION
010618
SCALE
ISO 2768-f
UCR245-5A
1:1.5
DIMENSIONS IN
MILLIMETERS
DIN
RoHS
Compliant
GENERAL
TOLERANCES
A3
DRAWN BY
D. Amigó
7508
3035
INSPECT. GUIDELINE
TECHNICAL DOC.
76143
01/06/2018
COMPATIBLE
DATE
DIMENSIONES GENERALES
SUBSTITUTES
DESCRIPTION
UNIDAD CONTROL UCR245-A
ADDITIONAL DESCRIPTION
PART NUMBER
DRAWING No.
Dimensions
mm
(in)
6
Work Place Example
*Not included, sold separately
TRA
CSR
SFR
CLR
UCR
GSFR
*
*
*
*
*
www.jbctools.com
7
Maintenance
- Before carrying out maintenance, always disconnect the power supply and allow the equipment
to cool down.
- Periodically check all cable and tube connections.
- Replace a blown Fuse as follows:
1. Pull off the Fuse Holder and remove the
Fuse. If necessary, use a flat screwdriver to
lever it off.
- Replace any defective or damaged part. Only use original JBC spare parts.
- Repairs should be performed only by a JBC authorized technical service.
Fuse
Holder
2. Insert the new Fuse into the Fuse Holder and
return it to the station.
8
It is imperative to follow safety guidelines to prevent electric shock,
injury, fire or explosion.
- Do not use the equipment for any purpose other than soldering or rework. Incorrect use may cause fire.
- The main cable must be plugged into approved bases. Make sure that it is properly grounded before
use. When unplugging it, hold the plug, not the wire.
- Do not leave the appliance unattended while it is on.
- Be sure that the power supply is disconnected before changing any spare part.
- The temperature of accessible surfaces may remain high after the device is turned off. Handle with
care.
- Heat can cause inflamable products to ignite even when not visible.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working
to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
Safety
www.jbctools.com
9
Notes
10
Specifications
UCR
Control Box for Robot
Ref.: UCR245-5A
Ref.: UCR470-5A
UCR245-5A 100 - 240V 50/60Hz. Input fuse: 2.5A. Output: 21V.
- Output Peak Power: 160W
- Temperature Range: 90 - 450 ºC / 190 - 840 ºF
- Total Net Weight: 2581 g / 5.69 lb
- Package Dimensions/Weight: 328 x 258 x 208 mm / 3160 g
(L x W x H) 12.91 x 10.16 x 8019 in / 6.97 lb
UCR470-5A 100 - 240V 50/60Hz. Input fuse: 3.5A. Output: 42V.
- Output Peak Power: 250W
- Temperature Range: 90 - 500 °C / 190 - 930 °F
- Total Net Weight: 2635 g / 5.81 lb
- Package Dimensions/Weight: 328 x 258 x 208 mm / 3215 g
(L x W x H) 12.91 x 10.16 x 8019 in / 7.09 lb
UCR245-5A and UCR470-5A
- Temperature Range: 90 - 500 °C / 190 - 932 °F
- Idle Temp. Stability (still air): ±1.5 ºC / ±3 ºF
- Tip to ground resistance: < 2 ohms
- Tip to ground voltage: < 2mV RMS
- Ambient operating temp: 10 - 40 ºC / 50 - 104 ºF
- Connections: Communications: M8-5pins
Tool: M16-8pins
- Unit Dimensions: 210 x 162 x 75 mm
(L x W x H) 8.3 x 6.4 x 3.0 in
Complies with CE standards.
ESD protected housing.
www.jbctools.com
11
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
Get 1 extra year JBC warranty by registering here:
https://www.jbctools.com/productregistration/
within 30 days of purchase.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
0027876-0921
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
w innych językach
- English: jbc UCR User manual
Powiązane artykuły
-
jbc HM470 Instrukcja obsługi
-
jbc CDB Instrukcja obsługi
-
jbc CDE-BA Series Instrukcja obsługi
-
jbc CDA Instrukcja obsługi
-
jbc High-Precision Hot Air Station Instrukcja obsługi
-
jbc SF-210VB 230V Instrukcja obsługi
-
-
-
-