jbc WSB High-Temperature Wire Stripper Station Instrukcja obsługi

jbc
Marka
jbc
Model
WSB High-Temperature Wire Stripper Station
Typ
Instrukcja obsługi
INSTRUCTION MANUAL
WSB
High-Temperature
Wire Stripper Station
Manual ............................... 1 unit
Ref. 0022983
Control Unit ...................... 1 unit Stand .................................. 1 unit
Ref. WSBT-SB
High-Temperature Wire
Stripper Tweezers ........ 1 unit
Ref. WS440-B
Power Cord ...................... 1 unit
Ref. 0024092 (100V)
0023715 (120V)
0023714 (230V)
Stand cable ...................... 1 unit
Ref. 0024227
Cartridge Holder ............. 1 unit
Ref. SCH-A
Packing List
The following items are included:
This manual corresponds to the following references:
WSB-9B (100V)
WSB-1B (120V)
WSB-2B (230V)
Metal Brush....................... 1 unit
Ref. 0022793
Cartidges Extractor
Pliers .................................. 1 unit
Ref. PLR195
Screw Driver .................... 1 unit
Re f. 0023 511
WS440 Sealing Plug .... 2 units
Ref. OB3000 (includes 10x)
2
Features and Connections
Power Socket
Control Unit
Stand
Ref. WSBT-B
Stand cable
Ref. 0024227
Equipotential connector
USB Connector
Main Switch
Fuse
High-Temperature Wire
Strippers Tweezers
Ref. WS440-B
W440 Cartridges
(not included)
www.jbctools.com
3
Mark
Align the cartridges in working position using
a fl at pliers (JBC Ref. PLR-195).
The conical cartridge aligner helps centering
both cartridges and ensure a good
functionality.
Fix the cartridges in its working position. by
tightening the screw.
Important: It is essential to tighten the screws
for the tool to function.
Cartridge Electric
Connection Screw
3. Positioning 4. Fixing
Insert the cartridge until the reference mark.
Take the mark as reference and check that both
tips match.
Important: It is esential to insert the cartridge
till the mark for a good connection.
Loosen the screws and remove the cartridges.
Changing Cartridges
1. Removing 2. Inserting
Cartridge aligner
4
Strip Gauge Knob Strip Gauge
Adjustable Strip Gauge
Adjust the strip gauge according to your stripping requirements.
Place the wire touching the strip gauge.
3. Remove Wire
Pull the wire stripper toward to stripp off
the wire end.
2. Close Cartridges
Choose cartridges according to the wire
diameter. Pinch the wire with the blades. The
pinched area will be melted by heat.
Stripping a Wire
1. Align Wire
www.jbctools.com
5
Power 75%
Power 75%
Kapton
®
PI
90%
Power 59%
Power 59%
Custom 68%
Power 75%
Power 75%
Kapton
®
PI
90%
1. Material Mode
Control Process
Choose between the different materials
by pressing the buttons and to
choose between all different material
options.
To work on a customized mode, press
and then the buttons and to
select the power level.
2. Custom Mode
WSS offers two different working modes. Switch the power on choose between Material Mode
and Custom Mode by pressing the button.
Selected Material
Work Screen
Next Material
Power Level
Previous Material
Instant Power
Work Mode
6
Power 75%
Power 75%
Kapton
®
PI
90%
Power 35%
Power 35%
Kapton
®
Sleep
90%
PI
Power 0%
Power 0%
Kapton
Hibernation
90%
PI
®
WSST
WSST/
WSSB
WSBT
WSBT-B
WSST
WSST/
WSSB
WSBT
WSBT-B
WSST
WSST/
WSSB
WSBT
WSBT-B
Station troubleshooting available on the product page at www.jbctools.com
Troubleshooting
1. Work 2. Sleep 3. Hibernation
When the wire stripper is lifted
from the stand, the cartridges
will heat up according to the
selected configuration.
When the wire stripper is in the
stand, the power falls after a
specified time.
After longer periods of
inactivity, the power is cut off
and the cartridges cool down
to room temperature.
Operation
Depending on where the tool is located, the soldering station switches between three different
states: Work, Sleep and Hibernation.
www.jbctools.com
7
Material Mode
WSU incorporates predeterminated power levels and it also features a customized work mode. It
allows you to work on wire insulations made of thermoplastics and thermostable materials such
as Tefl on1, Kapton2, silicone, rubber, etc.
Options included:
Insulation Material Symbol Power Level
Polyvinyl Chloride PVC 6%
Polyethylene PE 7%
Nylon ¹ PA 10%
Kynar ² PVDF 16%
Tefzel ¹ ETFE 17%
Teflon ¹
FEP 16%
PFA 21%
PTFE 40%
Ethylene Propylene
Rubber EPM/EPR 44%
Silicone Rubber SI 51%
Kapton ¹ PI 90%
ThermoplasticsThermostable
¹ Registred Trade Marks of DuPont
² Registred Trade Marks of Arkema
8
W440025
Cartridge
Ref.
Flat Blade
12,5 / 0.4921
Tip
mm / in
Cartridge
Ref.
W440023
Cartridge Range
WS440 is compatible with W440 Blade Cartridge Range. Find the model that best suits your
soldering needs on www.jbctools.com.
If an application requires a special tip design, contact JBC by mail [email protected].
22
24
26
28
AWG
Solid
34
30
Cartridge
Ref.
W440021
0,64 / 0,0252
0,51 / 0,0201
0,40 / 0,0157
0,32 / 0,0126
Tip Hole ø
mm / in
0,16 / 0,0063
0,25 / 0,0098
24 (7x32)
24 (19x36)
26 (10x36)
26 (19x38)
28 (19x40
27 (7x35)
30 (19x42)
30 (7x38)
AWG
Stranded
36 (7x44)
32 (19x44)
AWG
Solid
18
20
26
24
22
16
1,02 / 0,0402
Tip Hole ø
mm / in
0,81 / 0,0319
0,40 / 0,0157
0,51 / 0,0201
0,64 / 0,0252
1,29 / 0,0508
AWG
Stranded
20 (7x28)
20 (19x32)
20 (42x36)
22 (19x34)
27 (7x35)
28 (19x40)
26 (10x36)
26 (19x38)
24 (7x32)
24 (19x36)
18 (19x30)
www.jbctools.com
9
Note the sealing plug mounting position:
The chamfered side has to be positioned to-
wards the handle.
2. Mounting
3. Inserting
1. Removing
Seal
Handle
Gently push the sealing plug inside the handle
until it is completely into the handle.
Handle and seal edges have to be aligned.
Enter a small shaft or screwdriver in order to
gently lift and pull the sealing plug.
Do not insert the tool more than 8 mm deep.
Never use a cartridge to do this operation.
Sealing Plug Replacement
The Sealing Plug is meant to prevent undesirable flux vapors or particles from entering inside the
tool.
Its usage is highly recommended for intensive applications when soldering is exposed to FOD
environments or for applications where the soldering iron works close to vertical position.
Before replacing the seal, unplug the power supply and make sure the device is not hot.
10
Accessories
To open or fi x the wire stripper srews use JBC Flat Screw Driver Ref. 0023511.
To manipulate the cartridges use JBC Cartridge Extractor Pliers Ref. PLR195. More Information at
www.jbctools.com
Align cartridges with JBC pliers.Remove cartriges with JBC pliers.
Removing Inserting and Positioning
Flat Screw Driver*
Cartridge Extractor Pliers*
For cleaning the tips if unwanted material is stuck there. Metal Brush Ref. 0022793.
Metal Brush
www.jbctools.com
11
To reverse the pedal
functionality from
NO (Normally Open)
to NC (Normally Close)
NO
NC
Pedal Kit for Control Units
High-Temperature Wire
Stripper Tweezers
Ref. WS440-B
Stand
Ref. WSBT-B
Pedal Connecting Box
Pedal Kit for Control Units
Ref. P-305
(not included)
Control Unit
Pedal P305 can be used to activate/deactivate the Wire Stipper. Previously the Hibernation delay has
to be set to 0 min.
Lift the wire stripper from the stand, press and hold the pedal to activate them and strip the wire.
Once the pedal is relaesed the wire stripper enters in Hibernation. To reverse the pedal functionality flip
the switch of the connection box.
Default PIN: 0105.
12
Maintenance
Fuse
- Replace any defective or damaged pieces. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
Before carrying out maintenance or storage, always allow the equipment to cool and unplug the stand
from the station and the tool.
- Clean the station screen with a glass cleaner
or a damp cloth.
- Use a damp cloth to clean the casing, the
stand and the tool. Alcohol can only be
used for cleaning the metal parts.
- Periodically check that the metal parts of the
tool and stand are clean so that the station
can detect the tool status.
- Maintain tip surface clean in order to ensure a
correct stripped wire.
- Periodically check all cables.
- Replace a blown fuse as follows (see
specification chart) :
1. Pull off the fuse holder and remove the fuse.
If necessary use a tool to lever it off.
2. Press the new fuse into the fuse holder and
replace it in the station.
Clean
perodically
www.jbctools.com
13
Safety
Warning
- Do not touch the blade or the metal parts around.
- Do not allow the blade be close to flammable materials.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working
to avoid personal harm.
- This appliance can be used by children over the age of eight and also persons with reduced physical,
sensory or mental capabilities or lack of experience provided that they have been given adequate
supervision or instruction concerning use of the appliance and understand the hazards involved.
- Maintenance must not be carried out by children unless supervised.
- Place the tool on the stand when is not in use.
- Turn off the power when not in use, changing parts or storing.
Caution
- Do not use the Wire Stripper for other applications than wire stripping.
- Do not modify or customize the Wire Stripper.
- Do not hit the blade against workbench to eliminate stripped insulation debris. This behavior would
damage the blade.
- Remove power from the tool by holding the plug, not the wires.
- Be careful with the fumes produced when stripping. We recomend to use our fume extractor.
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
14
Specifications
WSB
High-Temperature Wire Stripper Station
Ref.: WSB-9B 100V 50/60Hz. Input Fuse: T1.6A. 5x20mm Output: 15V
Ref.: WSB-1B 120V 50/60Hz. Input Fuse: T1.25A. 5x20mm Output: 15V.
Ref.: WSB-2B 230V 50/60Hz. Input Fuse: T0.63A. 5x20mm Output: 15V.
- Temperature Max : 800 ºC /1472 °F
- Power: 75W
- Ambient operating temp: 10 to 50 ºC /50 to 120 ºF
- Connections: USB-B
- Control Unit Dimensions / Weight: 180 x 94 x 106 mm / 2.2 kg
(L x W x H) 7.1 x 3.7 x 4.2 in / 4.85 lb
- Total Net Weight: 3.8 kg / 8.4 lb
- Total Package Dimensions / Weight: 368 x 368 x 195 mm / 4.6 kg
(L x W x H) 14.5 x 14.5 x 7.7 in /10.15 lb
Complies with CE standards.
ESD protected.
www.jbctools.com
15
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
Get 1 extra year JBC warranty by registering here:
https://www.jbctools.com/productregistration/
within 30 days of purchase.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
0022983-0422
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

jbc WSB High-Temperature Wire Stripper Station Instrukcja obsługi

jbc
Marka
jbc
Model
WSB High-Temperature Wire Stripper Station
Typ
Instrukcja obsługi
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty