SF
Automatic Solder Feeder
INSTRUCTION MANUAL
Manual ............................... 1 unit
Ref. 0021633
Allen key Ø 1,5 ................ 1 unit
Ref. 0741610
SF Control Unit ............. 1 unit
Allen key Ø 2,5 ................ 1 unit
Ref. 0 012574
Power cable .................... 1 unit
Ref. 0023715 (100V/120V)
0023714 (230V)
Spanner ............................ 1 unit
Ref. 0017631
Guide Set ........................ 1 unit
Ref. GSF10V-B
Solder Feed Handle ....1 unit
Ref. SF280-A
Packing List
The following items are included:
This manual corresponds to the following references:
SF-110V B (110-120V) with Guide Set ø1mm
SF-210VB (230V) with Guide Set ø1mm
Reel Support .................. 1 unit
Ref. 0019301 (x1) - Support
0018033 (x1) - Axis
0003412 (x2) - Lock Ring
0014427 (x2) - Knob
Lock Ring
Knob
Support
Axis
2
Power Socket
Fuse
RJ12 connection
for Robot System
RJ12 connection for Station
USB-B connector
Tin wire inlet
Features and Connections
Solder
Feed Handle
Ref. SF280-A
Control Unit
Main Switch
Control Screen
www.jbctools.com
3
Tool Assembly
Connect the tool to the control unit.
1. Push the guide tube to the end
and tighten the screw.
2. Connect the jack.
Load the Solder Wire
1. Put the reel into its support.
2. Feed the wire into the input nozzle (2) until it reaches the wheels.
1
1
2
Input
nozzle
1
2
3. Use the Tin Reload Process
in Main Menu by pressing
the tool button.
4. Make sure the wire passes
through the nozzle.
insert to the end
4
Changing the Wheels and the Blade
1. Use the allen key and the spanner to loosen
the screws.
2. Replace the guide wheel and the blade for
the new ones.
Guide
wheel Blade
clamp
Blade
For this operation, disconnect the unit.
* Handle with care to avoid any cuts with the
blade because it is sharp.
2. You can easily adjust the length of the tube by opening the tube clamp.
Replacing the Guide Tube
1. Open the guide clamp, take off the guide tube and insert the new one.
For this operation, disconnect the tool from the control unit.
www.jbctools.com
5
BackBack
Setting Program 35Setting Program 35
Continuous Mode Discontinuous Mode Program 35
Speed Length Length
STEP1 STEP2
Speed Speed
Supplied: 2.0mm 0:05 40% 40%
mm/s mm mm
mm/s mm/s
40.0 1.5 1.5
20.0 20.0
STEP3
Length Speed
mm mm/s
5.0 20.0
STEP 1
STEP 2
STEP 3
BackBack
Edit ProgramEdit Program
mm
mm/s
STEP 1 STEP 2 STEP 3
35
5.0 3.0 1.5
20.0 24.5 20.0
FACTORY 1 1 Program 35
FACTORY 1
2 Program 22
LAB 2
3 Program 35
FACTORY 1
Program ConcatenationProgram Concatenation
BackBack
Work Screen
Control Process
Choose between continuous, discontinuous and program mode:
Program Mode
With the SF you can define up to 35 dynamic programs. In each one you can configure up to 3
steps with different lenght wire and dispensing speed.
Execute them sequentially and cyclically with the ‘Edit Concatenation List’ option.
Station troubleshooting available on the product page at www.jbctools.com
Troubleshooting
6
Main MenuMain Menu
5 Tin Reload Process
6 Counters
7 Software Version
1 Reset settings
2
Station settings
3
Tool settings
4 Programs Settings
ExitExit
1 Length units*
mm
2
Beep Off
3 PIN On
4 Change PIN
1 Mode
Discontinuous
2
Backward Off
Tool SettingsTool Settings
Station SettingsStation Settings
BackBack
BackBack
1 Edit Program
2
Delete Program
3
Edit Concatenation List
Program SettingsProgram Settings
Ba
ckward Forward
Reload ProcessReload Process
1 Plugged hours
7605
2
Working hours 350
3 Supplied mm 560
4 Work Cycles 75830
CountersCounters
BackBack
5 Reset partial counters
Press Enter to toggle*
Press enter when finished
BackBack
5 Station Locket
Off
6
Robot Mode Off
Menu Screen
Default PIN: 0105
Control Process
*switch total and partial
counters
*switch mm and inches
www.jbctools.com
7
Solder Wire Ø (mm) With Solder Wire Perforation Solder Wire Ø (mm) Without Solder Wire Perforation
- - 0.5-0.6 GSF05D-B
0.8 GSF08V-B 0.7-0.8 GSF08D-B
1.0 GSF10V-B 0.9 -1.0 GSF10D-B
1.5 GSF15V-B 1.2-1.5 GSF15D-B
Accesories
Stand for SF280
Ref. SF-SE
It prevents the SF280-A Solder Feed Handle
from rolling away while working.
Different guide sets are available depending on the diameter of the used
solder wire.
8
Before carrying out maintenance, always allow
the equipment to cool down.
- Clean the station screen with a glass cleaner
or a damp cloth.
- Use a damp cloth to clean the casing and the
tool. Alcohol can only be used to clean the
metal parts.
- Periodically check all cables and tubes.
Clean periodically
Maintenance
1. Pull off the fuse holder and remove the
fuse. If necessary use a tool to lever it off.
2. Insert the new fuse into the fuse holder
and return it to the station.
- Replace a blown fuse as follows:
- Replace any defective or damaged parts. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
www.jbctools.com
9
Safety
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to activate the sleep mode.
The soldering tip, the metal part of the tool and the stand may still be hot even when the station
is turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
10
产品中有害物质的名称及含量
有害物质含量表
部件名称
有害物质
铅(Pb) 汞(Hg) 镉(Cd) 六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
烙铁头 OOOOO O
手柄 OOOOO O
电源线 OOOOO O
主机 OOOOO O
电源插座 OOOOO O
保险丝 OOOOO O
主开关 OOOOO O
电位连接 X O O O O O
变压器 OOOOO O
线路板 X O O O O O
O 表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572 规定的限量要求以下。
X 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要求。
www.jbctools.com
11
0021633-0221
Specifications
SF-110V B 100-120V 50/60Hz. Input fuse: 0.2A.
SF-210VB 230V 50/60Hz. Input fuse: 0.125A.
- Spool capacity up to 1 kg / 2.2 Ib
- Max Spool Diam.: 80 mm / 3.15 in
- Max. Spool Height: 75mm / 2.95 in
- Solder diameter Ø 0,5 - 1,5 mm / Ø 0.02 - 0.059 in
- Max. Wire lenght 250 mm / 9.84 in
- Max. Forward speed 120 mm/s / 4.72 in/s
- Max. Reverse speed 120 mm/s / 4.72 in/s
- Ambient operating temp: 10 - 50 ºC / 50 - 122 ºF
- USB connector station-PC
- Robot connector
- Dimensions/Weight: 140 x 150 x 120 mm / 2.32 kg
(L x W x H 5.5 x 5.9 x 4.72 in / 5.11 lb
- Total package Dimensions / Weight: 368 x 368 x 195 mm / 3.23 kg
(L X W X H) 14.5 x 14.5 x 7.68 in / 7.12 lb
Complies with CE standards.
ESD protected.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
Get 1 extra year JBC warranty by registering here:
https://www.jbctools.com/productregistration/
within 30 days of purchase.
www.jbctools.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
w innych językach
- English: jbc SF-210VB 230V User manual
Powiązane dokumenty
-
jbc CDA Instrukcja obsługi
-
jbc AP250 Instrukcja obsługi
-
jbc TESE-QA Precision Hot Air Station extractor desk Instrukcja obsługi
-
-
-
-
jbc High-Precision Hot Air Station Instrukcja obsługi
-
jbc AL250 Instrukcja obsługi
-
jbc UCR Instrukcja obsługi
-
jbc HM470 Instrukcja obsługi