Parkside 75273 Operation and Safety Notes

IAN 75273

MODELLING & ENGRAVING SET PMGS 12 B2

MODELLBAU- UND GRAVIERSET

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

MODELLING & ENGRAVING SET

Operation and Safety Notes

Translation of original operation manual

ZESTAW MODELARSKI I GRAWERSKI

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

KOMPLET ZA MODELIRANJE IN GRAVIRANJE

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

MODELÁŘSKÁ A GRAVÍROVACÍ SADA

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

MODELÁRSKA A GRAVÍROVACIA SÚPRAVA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

GB Operation and Safety Notes Page 5

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 17

SI Navodila za upravljanje in varnostna opozorila Stran 31

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 45

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 57

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 69

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funk cjami urządzenia.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

MODELLBAU- UND GRAVIERSET

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

ZESTAW MODELARSKI I GRAWERSKI

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

A

11

8 9

C

B

16

14

15

18

22

20

21

13

12

23

10

D

F

E

G

8 10

4

321

45

76

x1

0

U

/

m

i

n

5

8

1

2

1

6

2

0

„EIN (ON)“

„AUS (OFF)“

17

19

5 GB

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features and equipment .....................................................................................................................Page 6

Included items .....................................................................................................................................Page 7

Technical information .......................................................................................................................... Page 7

General safety advice for electrical power tools .........................................Page 7

1. Workplace safety ...........................................................................................................................Page 8

2. Electrical safety ............................................................................................................................... Page 8

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 9

5. Service .............................................................................................................................................Page 9

Safety advice for all uses ....................................................................................................................Page 9

Safety advice relating to kickback .....................................................................................................Page 11

Special safety advice relating to grinding and disc-cutting ..............................................................Page 11

Further special safety advice for disc-cutting ..................................................................................... Page 12

Special safety advice for abrading using sandpaper ......................................................................Page 12

Special safety advice for polishing ....................................................................................................Page 12

Special safety advice for working with wire brushes ........................................................................Page 12

Device-specific safety instructions for small drill PMGS 12 B2 and mains

adapter-PMGS 12 B2-1 .....................................................................................................................Page 12

Operation

Inserting or replacing a tool / collet ...................................................................................................Page 13

Switching on and off / Setting the speed range ................................................................................Page 14

Advice on working with materials / Tools / Speed ranges ...............................................................Page 14

Tips and tricks ...................................................................................................................................... Page 15

Maintenance and cleaning ............................................................................................... Page 15

Service ...............................................................................................................................................Page 15

Warranty .........................................................................................................................................Page 15

Disposal ............................................................................................................................................Page 15

Conformity Declaration / Manufacturer ................................................................Page 16

6 GB

Introduction / General safety advice for electrical power tools

Introduction

Modelling and engraving set

PMGS 12 B2

Q

Introduction

We congratulate you on the purchase of

your new device. You have chosen a

high quality product. The instructions for

use are part of the product. They contain important

information concerning safety, use and disposal.

Before using the product, please familiarise yourself

with all of the safety information and instructions

for use. Only use the unit as described and for the

speciﬁed applications. If you pass the product on

to anyone else, please ensure that you also pass

on all the documentation with it.

Q

Proper use

The small drill is to be used for drilling, milling, en-

graving, polishing, cleaning up, grinding, separating

and sawing of wood, metal, plastic, ceramic or stone

in dry rooms. Any other use or modiﬁcation to the

drill / grinder shall be considered as improper use

and could give rise to considerable dangers. The

manufacturer will not accept liability for loss or

damage arising from improper use. Not intended

for commercial use.

Q

Features and equipment

Small drill:

1

Rotational speed control

2

ON / OFF switch

3

Metal stirrup hanger

4

Plug for mains adapter

5

Clamping nut

The following pictograms are used in these operating instructions / on the device:

Read instruction manual!

Keep children away from electrical

power tools!

V

~

Volt (AC)

Caution – electric shock!

Danger to life!

W

Watts (Eﬀective power) For indoor use only!

Direct current

(Type of current and voltage)

Risk of loss of life by electric shock

from damaged mains lead or mains

plug!

n

0

Design no-load speed

Wear hearing protection, dust

protection mask, protective glasses

and protective gloves.

mA

A / Ah

Milliamps / Amps / Amp-hours

Avoid contact with rapidly

rotating tools!

Safety class II Risk of ﬁre!

Observe caution and safety notes! Proper procedure and handling.

Risk of explosion!!

Dispose packaging and appliance in

an environmentally-friendly way!

7 GB

Introduction / General safety advice for electrical power tools

6

Spigot nut

7

Spindle lock

Mains adapter (see Fig. A):

8

Plug-in device for plug

4

9

Tray

10

Mains adapter

11

Power cable (with mains plug)

Accessories (see Fig. B):

12

6 HSS drills

13

2 Mandrels for mounting tools

14

3 Polishing wheels

15

4 Grinding wheels

16

1 Metal brush

17

16 Cutting wheels

18

5 Collets

19

2 Plastic brushes

20

3 Milling bits

21

2 Engraving bits

22

5 Grinding bits

23

1 Combination tool

Q

Included items

1 Small drill

1 Mains adapter

1 Plastic case

1 Accessory kit (50-piece)

1 Operating instructions

Q

Technical information

Small drill PMGS 12 B2:

Nominal voltage: 12 V

Nominal input: 22 W

Idle-running speed: n

0

5000–20000 min

-1

Max. drill bit diameter: ø 3.2 mm

Certiﬁed acc. to:

EN60745-1; EN60745-2-1

EN60745-2-3

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 54.70 dB(A)

Sound power level: 65.70 dB(A)

Uncertainty K: 3 dB

Evaluated acceleration, typical:

Hand / arm vibration: 1.868 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level given in these

instructions has been measured in accordance with

a standardised measurement procedure speciﬁed

in EN 60745 and can be used to compare devices.

Diﬀerent uses of the device give rise to diﬀerent

vibration levels and in many cases they may exceed

the values given in these instructions. It is easy to

underestimate the vibration load if the electrical pow-

er tool is used regularly in particular circumstances.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

Mains adapter PMGS 12 B2-1:

INPUT:

Rated voltage: 230 V∼ 50 Hz

OUTPUT:

Nominal voltage: 12 V

Nominal current: 1 A

Protection class: II /

Certiﬁed acc. to: EN61558

General safety advice for

electrical power tools

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

8 GB

General safety advice for electrical power tools

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools

powered by rechargeable batteries (without a

mains lead).

1.

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

b)

Do not work with the device

in potentially explosive envi-

ronments in which there are

inflammable liquids, gases or dusts.

Electrical power tools create sparks, which can

ignite dusts or fumes.

c)

Keep children and other

people away while you are

operating the electrical tool.

Distractions can cause you to lose control of

the device.

2.

Electrical safety

a)

The mains plug on the device must match

the mains socket. The plug must not

be modified in any way. Do not use

an adapter plug with devices fitted

with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed

.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d)

Do not use the mains lead for

any purpose for which it was

not intended, e.g. to carry the

device, to hang up the device or to pull

the mains plug out of the mains socket.

Keep the mains lead away from heat,

oil, sharp edges or moving parts of the

device. Damaged or tangled mains leads

increase the risk of electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b)

Wear personal protective

equipment and always wear

safety glasses. The wearing of

personal protective equipment such as dust

masks, non-slip safety shoes, safety helmets or

ear protectors, appropriate to the type of elec-

trical power tool used and work undertaken,

reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical power

tool is switched off before you connect

it to the mains, pick it up or carry it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing

and balance at all times. By doing this

9 GB

General safety advice for electrical power tools

you will be in a better position to control the

device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4.

Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug from the socket

before you make any adjustments to

the device, change accessories or when

the device is put away. This precaution is

intended to prevent you from unintentionally

starting the device.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working proper-

ly and move freely. Check for any parts

that are broken or damaged enough

to detrimentally affect the functioning

of the device. Have damaged parts

repaired before you use the device.

Many accidents have their origins in poorly

maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Q

Safety advice for all uses

General safety advice for grinding,

sanding (with sandpaper), wire brushing,

polishing and disc-cutting:

a) This electrical power tool is intended

for use as a grinding, sanding, wire-

brushing, and disc-cutting machine.

Observe all the safety advice, instruc-

tions, information in figures and all

other information you received with

this device. If you do not observe the following

advice it could lead to electric shock, ﬁre and /

or serious injury.

b) Normative statement / advice for this tool is not

applicable.

c) Do not use any accessory not specifi-

cally intended by the manufacturer for

this electrical power tool. Although an

accessory may ﬁt on your electrical power tool,

this does not on its own guarantee that it can

be safely used.

10 GB

d) The maximum permitted speed of an

attachment must be at least as high as

the maximum speed indicated for the

electrical power tool. An accessory rotating

faster than its permitted speed could disintegrate

or ﬂy oﬀ.

e) The external diameter and the thickness

of the attachment must be compatible

with the dimensions of your electrical

power tool. Attachments that are not dimen-

sionally compatible cannot be adequately

guarded or controlled.

f) Grinding discs, flanges, grinding

wheels or other accessories must fit

exactly on to the spindle of your elec-

trical power tool. Attachments that do not

exactly ﬁt on the spindle turn unevenly, vibrate

severely and could lead to loss of control.

g) Do not use damaged attachments.

Before every use check attachments

such as grinding discs for loose frag-

ments and cracks, grinding wheels for

cracks, deterioration or excessive

wear and wire brushes for loose or

broken wires. If the electrical power

tool or attachment is dropped, inspect

for damage or change the attachment

for an undamaged one. When you

have inspected and inserted the at-

tachment, position yourself and by-

standers away from the plane of the

rotating attachment and run the device

at maximum speed for one minute.

Damaged attachments will usually break apart

during this test.

h)

Wear personal protective

equipment. Use a full face vi-

sor, safety goggles or safety

glasses, depending on the application.

Wear a dust mask, hearing protectors,

safety gloves or special apron capable

of stopping particles of the grinding

medium or workpiece, as appropriate

for the task. Eyes must be protected from

the ﬂying debris which can arise from some

operations. Dust or breathing masks must be

capable of ﬁltering out the dust generated by

the application. Prolonged exposure to loud

noise can lead to hearing loss.

i) Keep bystanders at a safe distance

from your work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of the

workpiece or of a broken attachment could ﬂy

oﬀ and cause injury beyond the immediate

working area.

j) Hold the device by the insulated han-

dle surfaces when you are undertak-

ing work where there is the danger

of the attachment striking hidden

electricity cables or the device’s mains

lead. Contact with a live wire could cause

metal parts of the device to become live and

lead to electric shock.

k) Keep the mains lead away from rotat-

ing attachments. If you lose control of the

device the mains lead may become severed or

trapped and your hand or arm may be pulled

into the rotating attachment.

l) Never lay the electrical power tool

down until after the attachment has

come to a complete standstill. The rotat-

ing attachment may snag when it comes into

contact with the surface and cause you to lose

control of the device.

m) Do not have the electrical power tool

running while you are carrying it. Your

clothing could become trapped by unintention-

al contact with the rotating attachment and the

tool could be pulled into your body.

n) Clean the ventilation slots on your

electrical power tool regularly. The mo-

tor’s fan draws dust into the housing. A build-up

of metal dust could give rise to an electrical

hazard.

o)

Never use the electrical

power tool near inflammable

materials. Sparks could ignite

these materials.

p) Do not use attachments that require

the use of coolants. The use of water or

other liquid coolants could result in electric shock.

General safety advice for electrical power tools

11 GB

Q

Safety advice

relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding

disc, grinding pad, wire brush etc. Pinching or

snagging results in the rotating attachment coming

to an abrupt stop. This causes the electrical power

tool (if not controlled) to move in the opposite di-

rection to the direction of rotation of the attachment

at the point of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback. The

grinding disc moves towards or away from the op-

erator, depending on the direction of movement of

the disc at the point of constraint. The grinding disc

could also break.

Kickback occurs as a result of incorrect use or misuse

of the electrical power tool. It can be prevented by

taking the appropriate precautions as described below.

a) Maintain a firm grip on the electrical

power tool and position your body

and arms to allow you to resist kick-

back forces. Always use the auxiliary

handle, if provided, to exercise the

greatest possible control over kick-

back forces or reaction torques as the

device builds up to full speed. By taking

suitable precautions the operator can control

kickback and reaction forces.

b) Do not place your hands near a rotat-

ing attachment. If kickback occurs the at-

tachment could move over your hand.

c) Avoid positioning your body in the

area into which the electrical power

tool would move in the event of a

kickback. A kickback moves the electrical

power tool in the opposite direction to the di-

rection of movement of the grinding disc at the

point of constraint.

d) Work particularly carefully in the

area of corners, sharp edges etc. to

avoid the attachment bouncing or

snagging on the workpiece. Corners,

sharp edges or bouncing have a tendency to

snag the rotating attachment. This causes loss

of control or kickback.

e) Do not use saw-chain woodcarving

discs or toothed discs. Such attachments

create frequent kickback and loss of control of

the electrical power tool.

Q

Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for

the type of abrasive consumable you

are using. Always use abrasive consumables

approved for use with your electrical power

tool. Abrasive consumables not approved for

use with your electrical power tool cannot be

adequately guarded and are unsafe.

b) To ensure the highest level of opera-

tional safety, the disc guard cover must

be attached to the electrical power tool

and set in such a way that the smallest

possible area of the abrasive consum-

able is exposed to the operator. The disc

guard cover is there to protect the operator from

pieces breaking oﬀ and accidental contact with

the abrasive consumable.

c) Abrasive consumables must be used

only for their recommended purpos-

es, For example: never grind with the

side face of a cutting disc. Cutting discs

are intended for removing material using the

edge of the disc. Sideways forces on these

abrasive consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce the

chance of it breaking. Flanges for cutting discs

are

diﬀerent from the ﬂanges for other abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.

General safety advice for electrical power tools

12 GB

Q

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut-

t

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Q

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Q

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

Q

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) U

se a guard, if recommended, but m

ake

sure that the wire brush does not come

into contact with the guard. The diameters

of disc brushes and cup brushes can increase

due to contact pressure and centripetal forces.

Device-speciﬁc safety

instructions for small drill

PMGS 12 B2 and mains

adapter-PMGS 12 B2-1

When you use the drill /

grinder wear the following

protective equipment: safety glasses

and protective gloves.

General safety advice for electrical power tools / Operation

General safety advice for electrical power tools

13 GB

CAUTION! The tool continues to rotate

after it has been switched off!

Avoid contact with rapidly rotating

drill / grinder components.

Securely support the

workpiece. Use clamps or a vice to grip the

workpiece ﬁrmly. This is much safer than holding

it in your hand.

Never support your-

self by placing your hands near or in

front of the device or the workpiece

surface. A slip can result in injury.

Avoid contact with moving sanding or

grinding tools.

DANGER OF FIRE FROM FLYING

SPARKS! Abrading metal creates

ﬂying sparks. For this reason, always

make sure that nobody is placed in any danger

and that there are no inﬂammable materials

near the working area.

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person

operating the device and to anyone near the

work area.

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Avoid abrading paints containing lead

or other substances hazardous to

health.

Do not machine materials containing

asbestos. Asbestos is a known carcinogen.

Do not machine moist materials or

damp surfaces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

Switch the device off

and allow it to come to a standstill be-

fore you put it down.

Always keep the de

vice

clean, dry and free of oil or grease.

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsible

for their safety. Children must never be allowed

to play with the device.

Q

Operation

Never use the device for a purpose

for which it was not intended or with

non-original parts / accessories. The use

of tools or accessories other than those recom-

mended in the operating instructions could lead

to you suﬀering an injury.

Q

Inserting or replacing

a tool / collet

Press the spindle lock

7

and keep it pressed.

Rotate the clamping nut

5

until the lock

engages.

Loosen the clamping nut

5

with the combina-

tion key

23

.

If a tool is already inserted, remove it.

First insert the tool you wish to use though the

clamping nut

5

before you insert it into the

collet

18

suitable for the tool shaft.

Press the spindle lock

7

and keep it pressed.

Insert the collet

18

into the threaded insert and

tighten the clamping nut

5

on the thread using

the combination key

23

.

Using the Insertion tool with mandrel

13

:

NOTE: Use the screwdriver end of the combi-

nation key

23

to release or tighten the screw of

the mandrels

13

.

Insert the mandrel

13

into the electrical tool as

described.

With the aid of the combination wrench

23

,

unscrew the screw from the mandrel

13

.

Place the insertion tool you wish to have onto

the screw between the two washers.

With the aid of the combination wrench

23

,

tighten the screw on the mandrel

13

.

General safety advice for electrical power tools / Operation

14 GB

Q

Switching on and oﬀ /

Setting the speed range

Switching on / Setting the speed range:

Connect the plug

4

to the power supply unit

10

by inserting it into the plug-in device

8

provided

for such purposes (see Fig. C).

Connect the device to the power supply by

inserting the mains plug into the socket.

Press down the ON / OFF switch

2

and then

move it in direction of the rotational speed con-

trol

1

. Then set the rotational speed control to

a position between “5” and “20”.

Switching off:

Set the rotational speed control

1

to position

“5”. Press down the ON / OFF switch

2

and

then move it in direction of the cable.

Q

Advice on working with

materials / Tools / Speed ranges

Use the highest speed when working on steel

or iron with the milling bits

20

.

Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

Use the low speed range for working on plastics

and low-melting point materials.

Use high speeds on wood.

Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experience

which tools and settings are the best for the materi-

als you work with.

Setting the appropriate speed:

Numeral on the

rotational speed

control

1

Material to be

worked on

5

Plastics and low melting

point materials

8

Stone, Ceramics

Numeral on the

rotational speed

control

1

Material to be

worked on

12

Softwood, metal

16

Hardwood

20

Steel

Examples of appropriate tool selection

Function:

Function Accessory Application

Drilling

HSS drill

12

Drilling wood

Milling Milling bits

20

Various tasks, e.g.

hollowing out,

gouging, shaping,

grooving or slotting

Engraving Engraving

bits

21

Making marks,

craft projects

(see Fig. D)

Polishing,

derusting

CAUTION!

Use only the

lightest con-

tact pressure

of the tool on

the work-

piece.

Metal brush

16

Derusting

Polishing

wheel

14

Working on vari-

ous metals and

plastics, in particu-

lar noble metals

like gold or silver

(see Fig. E)

Cleaning Plastic brush

19

E.g. cleaning com-

plex plastic hous-

ings or the area

around a door lock

Grinding Grinding

wheels

15

,

grinding bits

22

Grinding work on

stone, wood; ﬁne

work on hard mate-

rials such as ceram

ic

or alloyed steel

(see Figs. F, G)

Cutting and

sawing

Cutting discs

17

Cutting metal,

plastic or wood

Operation / Maintenance and cleaning / Service / Warranty / Disposal

Operation

15 GB

Q

Tips and tricks

If you use press too hard you run the risk of break-

ing the tool or damaging the workpiece. You will

achieve the best results by operating the tool at a

constant rotational speed and using a low contact

pressure on the workpiece.

Q

Maintenance and cleaning

The device is maintenance-free.

Clean all the dirt oﬀ the drill / grinder. Use a

dry cloth for cleaning.

Q

Service

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.

If the plug or lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.

Q

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tamper-

ing not carried out by our authorized service branch.

Your statutory rights are not restricted in any way

by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 75273

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive 2002 / 96 / EC

about waste electrical and electronic equipment

and its transposition into national legislation, worn

out electric tools must be collected separately and

taken for environmentally compatible recycling.

Please contact your municipal or city council to ask

about how to dispose of old electrical tools.

Operation / Maintenance and cleaning / Service / Warranty / Disposal

Operation

16 GB

Q

Conformity Declaration /

Manufacturer

We, Kompernaß GmbH, the person responsible for

documents: Mr Semi Uguzlu, Burgstr. 21, D-44867

Bochum, Germany, hereby declare that this product

complies with the following standards, normative

documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

Applicable harmonized standards

EN 60745-1:2009

EN 60745-2-1:2010

EN 60745-2-3:2007+A11

EN 55014-1:2006+A1

EN 55014-2:1997+A1+A2

EN 61558-1:2005+A1

EN 61558-2-6:2009

EN 61000-3-2:2006+A1+A2

EN 61000-3-3:2008

Type / Device description:

Modelling and engraving set PMGS 12 B2

Date of manufacture (DOM): 06–2012

Serial number: IAN 75273

Bochum, 30.06.2012

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of further development.

Conformity Declaration / Manufacturer

Spis zawartości

17 PL

Spis zawartości

Wstęp

Użytkowanie zgodnie z przeznaczeniem ......................................................................................Strona 18

Wyposażenie ...................................................................................................................................Strona 19

Zakres dostawy ................................................................................................................................Strona 19

Dane techniczne ..............................................................................................................................Strona 19

Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 20

2. Bezpieczeństwo elektryczne .......................................................................................................Strona 20

3. Bezpieczeństwo osób .................................................................................................................Strona 20

4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ..........................................Strona 21

5. Serwis ...........................................................................................................................................Strona 22

Wskazówki bezpieczeństwa dla wszystkich zastosowań ............................................................Strona 22

Odrzut i odpowiednie wskazówki bezpieczeństwa......................................................................Strona 23

Szczególne wskazówki odnośnie szlifowania i cięcia ..................................................................Strona 24

Dalsze szczególne wskazówki bezpieczeństwa dotyczące tarcz tnących ................................. Strona 24

Szczególne wskazówki bezpieczeństwa dotyczące szlifowania papierem ściernym ................Strona 25

Szczególne wskazówki bezpieczeństwa dotyczące polerowania .............................................. Strona 25

Szczególne wskazówki bezpieczeństwa dotyczące pracy przy użyciu szczotek drucianych ......Strona 25

Wskazówki dotyczące bezpieczeństwa użytkowania mini-wiertarki PMGS 12 B2

i zasilacza-PMGS 12 B2-1 .............................................................................................................Strona 25

Uruchomienie

Zakładanie / wymiana uchwytu mocującego ................................................................................Strona 26

Załączanie i wyłączanie / Nastawianie zakresu prędkości obrotowej .......................................Strona 27

Wskazówki dotyczące obróbki materiału / Narzędzia / Prędkości obrotowych ........................Strona 27

Dobre rady i triki .............................................................................................................................. Strona 28

Konserwacja i czyszczenie............................................................................................Strona 28

Serwis .............................................................................................................................................Strona 28

Gwarancja ..................................................................................................................................Strona 28

Usuwanie ..................................................................................................................................... Strona 29

Deklaracja zgodności / Producent ..........................................................................Strona 29

18 PL

Wstęp

Zestaw modelarski i grawerski

PMGS 12 B2

Q

Wstęp

Gratulujemy zakupu nowego urządzenia.

Tym samym zdecydowali się Państwo na

zakup produktu wysokiej jakości. Instrukcja

obsługi jest częścią tego produktu. Zawiera ona

ważne wskazówki dotyczące bezpieczeństwa,

użytkowania iutylizacji. Przed pierwszym użyciem

produktu należy zapoznać się ze wszystkimi wska-

zówkami dotyczącymi obsługi ibezpieczeństwa.

Używać produktu wyłącznie zgodnie zjego poniżej

opisanym przeznaczeniem. Wprzypadku przeka-

zania produktu innej osobie należy dołączyć do

niego całą jego dokumentację.

Q

Użytkowanie zgodnie

z przeznaczeniem

Mini-wiertarka jest przeznaczona do wiercenia, fre-

zowania, grawerowania, polerowania, czyszczenia,

szlifowania, cięcia i piłowania drewna, metalu, two-

rzywa sztucznego, ceramiki lub kamienia, w suchych

pomieszczeniach. Każde inne zastosowanie urzą-

dzenia lub zmiana dokonana w urządzeniu są

uznawane za niezgodne z przeznaczeniem i kryją

w sobie poważne zagrożenie nieszczęśliwym wy-

padkiem. Za szkody powstałe wskutek użytkowania

urządzenia sprzecznego z przeznaczeniem produ-

cent nie ponosi żadnej odpowiedzialności. Urządze-

nie nie jest przeznaczone do celów zarobkowych.

W niniejszej instrukcji obsługi urządzenia zastosowano następujące piktogramy:

Przeczytać instrukcję obsługi!

Dzieci trzymać z daleka od narzędzia

elektrycznego!

V

~

Volt (Napięcie przemienne)

Ostrzeżenie przed porażeniem prądem

elektrycznym! Zagrożenie dla życia!

W

Watt (Moc skuteczna)

Tylko do użytku wewnątrz

pomieszczeń!

Prąd stały

(rodzaj prądu i napięcia)

Niebezpieczeństwo utraty życia wskutek

porażenia prądem elektrycznym w

przypadku uszkodzonego kabla siecio-

wego lub uszkodzonej wtyczki sieciowej!

n

0

Projektowa liczba obrotów biegu luzem

Zakładać okulary ochronne,

ochronniki słuchu, maskę

przeciwpyłową i rękawice ochronne.

mA

A / Ah

Milliampery / Ampery / Amperogodziny

Unikać kontaktu z szybko wirującymi

narzędziami!

Klasa bezpieczeństwa II Niebezpieczeństwo pożaru!

Przestrzegaj wskazówek ostrzegaw-

czych i bezpieczeństwa!

To jest prawidłowy sposób

postępowania!

Niebezpieczeństwo wybuchu!

Opakowanie i urządzenie przekaż

do utylizacji zgodnie z przepisami o

ochronie środowiska!

19 PL

Wstęp

Q

Wyposażenie

Mini-wiertarka:

1

Regulacja prędkości obrotowej

2

Łącznik ZAŁ. / WYŁ.

3

Kabłąk metalowy

4

Wtyczka do zasilacza

5

Nakrętka mocująca

6

Nakrętka kołpakowa

7

Blokada wrzeciona

Zasilacz (patrz ilustracja A):

8

Wejście kabla z wtyczką

4

9

Półka

10

Zasilacz

11

Kabel sieciowy (z wtyczką)

Osprzęt (patrz Rysunek B):

12

6 Wierteł ze stali szybkotnącej o

podwyższonej wydajności skrawania

13

2 Trzpienie do mocowania narzędzi

14

3 Tarcze polerskie

15

4 Tarcze szliﬁerskie

16

1 Szczotka metalowa

17

16 Ściernic tarczowych do cięcia

18

5 Tuleje zaciskowe

19

2 Szczotki z tworzywa sztucznego

20

3 Nasadki frezowe

21

2 Nasadki grawerskie

22

5 Nasadek szliﬁerskich

23

1 Klucz uniwersalny

Q

Zakres dostawy

1 Mini-wiertarka

1 Zasilacz sieciowy

1 Walizka z tworzywa sztucznego

1 Zestaw osprzętu (50 części)

1 Instrukcja obsługi

Q

Dane techniczne

Mini-wiertarka PMGS 12 B2:

Napięcie nominalne: 12 V

Nominalny pobór mocy: 22 W

Prędkość obrotowa

biegu jałowego: n

0

5000–20000 min

-1

Maks. średnica wiertła: ø 3,2 mm

Certyﬁkacja wg: EN60745-1;

EN60745-2-1

EN60745-2-3

Informacje dotyczące hałasu i wibracji:

Wartość pomiarowa hałasu wyznaczona zgodnie

z EN 60745. Poziom hałasu elektronarzędzia wg

oceny A wynosi typowo:

Poziom ciśnienia hałasu: 54,70 dB(A)

Pozom mocy hałasu: 65,70 dB(A)

Niepewność pomiaru K: 3 dB

Określone przyśpieszenie, typowe:

Przenoszenie wibracji: 1,868 m / s

2

Niepewność K = 1,5 m / s

2

Podany w niniejszych instruk-

cjach poziom drgań wyznaczony został za pomocą

metody pomiarowej określonej w normie EN 60745

i może zostać użyty do porównania urządzeń.

Poziom wibracji będzie się różnił w zależności od

zastosowania elektronarzędzia i w niektórych

przypadkach może przekroczyć wartość podaną

w niniejszej instrukcji. Obciążenie drganiami może

być mniej uciążliwe, jeśli elektronarzędzie będzie

regularnie trzymane w ten sposób.

Wskazówka: Celem dokładnego oszacowania

obciążenia wibracjami w okresie określonego okresu

czasu pracy należy uwzględnić również te okresy, w

których urządzenie jest wyłączone lub wprawdzie

jest włączone, ale w rzeczywistości nie pracuje.

Może to przyczynić się do znacznej redukcji ob-

ciążenia wibracjami w całym okresie czasu pracy.

Zasilacz PMGS 12 B2-1:

WEJŚCIE / Input:

Napięcie znamionowe: 230 V∼ 50 Hz

WYJŚCIE / Output:

Napięcie nominalne: 12 V

Prąd znamionowy: 1A

Klasa ochronna: II /

Certyﬁkacja wg: EN61558

20 PL

Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

Ogólne wskazówki

bezpieczeństwa dla

elektronarzędzi

Przeczytaj wszystkie

wskazówki dotyczące bezpieczeństwa

oraz instrukcje! Zaniedbania w przestrzeganiu

wskazówek dotyczących bezpieczeństwa oraz w

przestrzeganiu instrukcji mogą spowodować pora-

żenie prądem elektrycznym, pożar i / lub ciężkie

obrażenia ciała.

Przechowuj na przyszłość wszystkie

wskazówki dotyczące bezpieczeństwa

oraz instrukcje!

Używany we wskazówkach dotyczących bezpie-

czeństwa termin „narzędzie elektryczne“ odnosi się

do narzędzi elektrycznych zasilanych z sieci (z ka-

blem sieciowym) oraz do narzędzi elektrycznych

zasilanych

z akumulatorów (bez kabla sieciowego).

1.

Bezpieczeństwo miejsca pracy

a) Utrzymywać stanowisko pracy w czy-

stości i dobrze oświetlone. Nieporządek

i nieoświetlone obszary robocze mogą prowa-

dzić do wypadków.

b)

Nie pracuj przy użyciu urzą-

dzenia w otoczeniu zagrożo-

nym eksplozją, w którym

znajdują się palne ciecze, gazy lub

pyły. Urządzenia elektryczne wytwarzają

iskry, które mogą zapalić pył lub pary.

c)

Podczas użytkowania urzą-

dzenia elektrycznego trzymaj

dzieci i inne osoby z daleka

od urządzenia. Przy odchyleniu możesz

stracić kontrolę nad urządzeniem.

2.

Bezpieczeństwo elektryczne

a) Wtyk sieciowy urządzenia musi

pasować do wtykowego gniazdka

sieciowego. W żaden sposób nie

wolno zmieniać wtyku sieciowego

urządzenia. Nie używaj żadnych wty-

ków adapterowych razem z urządze-

niami

wyposażonymi w uziemienie

ochron

ne. Niezmienione wtyki sieciowe i pa-

sujące wtykowe gniazdka sieciowe zmniejszają

ryzyko porażenia prądem elektrycznym.

b) Unikaj kontaktu fizycznego z powier-

zchniami uziemionymi takimi jak

powierzchnie rur, grzejników, kuchni

elektrycznych i lodówek. Istnieje podwyż-

szone niebezpieczeństwo porażenia prądem

elektrycznym, gdy twoje ciało jest uziemione.

c) Trzymaj urządzenie z daleka od desz-

czu i wilgoci. Wniknięcie wody do urządzenia

elektrycznego zwiększa ryzyko porażenia prą-

dem elektrycznym.

d)

Nie używaj kabla sieciowego w

sposób sprzeczny z jego prze-

znaczeniem, tj. do noszenia

urządzenia, zawieszania urzą dzenie

lub do wyciągania wtyku sieciowego

z wtykowego gniazdka sieciowego.

Trzymaj kabel z daleka od gorąca,

oleju, ostrych krawędzi lub porusza-

jących się części urządzeń. Uszkodzone

lub poplątane kable zwiększają ryzyko pora-

żenia prądem elektrycznym.

e)

Gdy pracujesz z urządzeniem elektrycz-

nym na dworze używaj wyłącznie

przedłużaczy, które są dopuszczone

również do pracy na dworze. Użycie

przedłużacza przystosowanego do stosowania

na dworze zmniejsza ryzyko porażenia prądem

elektrycznym.

f) Jeśli praca elektronarzędzia w otocze-

niu wilgotnym jest nie do uniknięcia,

należy zastosować wyłącznik prądu

uszkodzeniowego. Zastosowanie wyłącz-

nika prądu uszkodzeniowego zapobiega nie-

bezpieczeństwu porażenia prądem elektrycz

nym.

3. Bezpieczeństwo osób

a) Bądź stale uważny, zwracaj uwagę

na to co robisz i postępuj rozsądnie w

trakcie pracy z narzędziem elektrycz-

nym. Nie używaj narzędzia, gdy jesteś

Strona jest ładowana ...

Parkside 75273 Operation and Safety Notes

Ten podręcznik jest również odpowiedni dla

Parkside 75273 Operation and Safety Notes

w innych językach

Powiązane dokumenty

Inne dokumenty