Bissell CleanView Helix 22C1 Series Instrukcja obsługi

Marka: Bissell

Model: CleanView Helix 22C1 Series

Kategoria: Odkurzacze

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Thank You

USER'S GUIDE

32Y7 / 22C1 / 21K3 / 71V9 SERIES

Safety Instructions

Product View

Assembly

Operations

Maintenance and Care

Warranty

Troubleshooting

Product Registration

Consumer Services

6-8

8-12

14-15

Replacement Parts

Accessories

Earn BISSELL Rewards!

product today!

See details on

back page

*product images may vary

We’re glad you purchased a BISSELL vacuum. Everything we know

about floor care went into the design and construction of this

complete, high-tech home cleaning system.

Your carpet cleaner is well made, and we back it with a limited

warranty. We also stand behind it with a knowledgeable, dedicated

Consumer Services department, so, should you ever have a problem,

you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today,

BISSELL is a global leader in the design, manufacture, and service

of high quality homecare products like your carpet cleaner.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

President and Chief Executive Officer

www.bissell.com 800.237.7691

Thanks for buying a BISSELL CleanView Helix

www.bissell.com 800.237.7691

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical

appliance, basic

precautions should be observed, including

the following:

READ ALL INSTRUCTIONS BEFORE USING

UPRIGHT VACUUM

Always connect to a polarized outlet (left slot is

wider than right). Unplug from outlet when not in

use and before conducting maintenance.

WARNING:

To reduce the risk of fire,

electric shock, or injury:

■

Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

■

Do not leave vacuum cleaner unattended

when it is plugged in.

■

Unplug from outlet when not in use and

before servicing.

■

Unplug before attaching the TurboBrush Tool.

■

Do not use outdoors or on wet surfaces.

■

Do not allow children to operate vacuum

cleaner or use as a toy.

■

Close attention is necessary when used by

or near children.

■

Do not use for any purpose other than

described in this user’s guide.

■

se only manufacturer’s recommended

attachments.

■

Do not use with damaged cord or plug.

■



If appliance is not working as it should, has

been dropped, damaged, left outdoors, or

dropped into water, have it repaired at an

authorized service center.

■

Do not pull or carry by cord, use cord as a

handle, close a door on cord, or pull cord

around sharp edges or corners. Do not run

appliance over cord. Keep cord away from

heated surfaces.

■

Do not unplug by pulling on cord. To unplug,

grasp the plug, not the cord.

■

Do not handle vacuum cleaner or plug with

wet hands.

■



Do not put any object into openings. Do not

use with any opening blocked; keep openings

free of dust, lint, hair, and anything that may

reduce air flow.

■

Keep hair, loose clothing, fingers, and all parts

of body away from openings and moving parts.

■



Turn off all controls before plugging or

unplugging vacuum cleaner.

■

Use extra care when cleaning stairs.

■

Do not pick up flammable materials (lighter fluid,

gasoline, kerosene, etc.) or use in the presence

of explosive liquids or vapors.

■

Do not pick up toxic material (chlorine bleach,

ammonia, drain cleaner, etc.).

■

Do not use vacuum cleaner in an enclosed

space filled with vapors given off by oil

base paint, paint thinner, some moth

proofing substances, flammable dust, or

other explosive or toxic vapors.

■

Do not pick up hard or sharp objects such as

glass, nails, screws, coins, etc.

■

Do not pick up anything that is burning

or smoking, such as cigarettes, matches,

or hot ashes.

■

Do not use without filters in place.

■

Use only on dry, indoor surfaces.

■

Keep appliance on a level surface.

■

Do not carry the vacuum cleaner while it

is running.

SAVE THESE

INSTRUCTIONS.

FOR FUTURE USE

THIS APPLIANCE

HAS A

POLARIZED

PLUG.

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will fit in

a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a qualified

electrician to install a proper outlet. Do not

change the plug in any way.

This model is for household use only.

Power

Cord

Power

Switch

www.bissell.com 800.237.7691

Product view

WARNING:

Plastic film can be

dangerous. To avoid danger

of suffocation, keep away

from babies and children.

CAUTION:

Do not plug in your vacuum

cleaner until you are familiar

with all instructions and

operating procedures.

Carry Handle

Crevice Tool

Quick

Release

Cord

Wrap

Quick

Reach

Handle

Handle Release

Pedal

Powerfoot

Stretch Hose

TurboBrush

Tool

Extension

Wand

Furniture

Protection

Guard

Height

Adjustment

Knob

Dirt

Container

Lock ’n

Seal

™

Lever

Pre-Motor

Filter

Headlight

(selected models only)

Combination

Dusting

Brush/

Upholstery

Tool

Hose Clip

HEPA Media

Filter*

Hose

Wand

Base

Filter

Cup

Foot

Hose

Cord Clip

Handle

product images may vary

*The filter media, not the vacuum as a whole,

complies with IEST-RP-CC001.5 HEPA standard.

www.bissell.com 800.237.7691

Assembly

The only tool you’ll need to

assemble your vacuum cleaner

is a Phillips head screwdriver.

Attach handle to vacuum

1. Locate the vacuum handle and

remove the screw packet taped to

the base of the handle.

2. Stand the vacuum upright and

slide the base of the handle firmly

into the grooves at the top of the

vacuum body.

3. Check to be sure the handle is fitted

to the vacuum body. If there is a gap

in front, continue to push firmly until

the handle is flush.

4. Insert the screw provided from the

screw packet into the existing hole.

Tighten securely with a screwdriver.

Attach vacuum hose and tools

1. Attach the Twist ‘n Snap™ hose by

lining up the tabs on the base with

the corresponding notches on the

back of the vacuum.

2. Turn the Twist ‘n Snap hose to the

right to lock the hose into place.

3. Grasping the Quick Reach handle,

slide the end of the hose wand

onto the hose wand base. Snap

the hose into the hose clip.

NOTE: The powerfoot will not

suction properly unless the hose

wand is firmly attached.

4. Snap the extension wand and the

crevice tool together into the storage

clip. The crevice tool stores inside

the extension wand and snaps onto

the back of the unit.

5. Snap the combination tool into the

storage clip.

6. Attach the TurboBrush Tool by

aligning the small holes near the

brush roll with the tabs at the

bottom of TurboBrush Tool housing.

Snap TurboBrush Tool into place.

www.bissell.com 800.237.7691

Operations

Handle position

Press the handle release pedal with your

foot to place your CleanView Helix into

one of three cleaning positions.

1. Upright– For storage and above floor

cleaning with tools.

2. Normal cleaning – Press handle release

household floor cleaning tasks.

3. Low cleaning –With the vacuum in

normal cleaning position, press handle

release pedal again, use for reaching under

low furniture such as tables, chairs or beds.

Height adjustment

There are five height settings available

for various floor surfaces. Turn the dial

on the foot of the cleaner to the desired

setting.

Lowest setting – For low pile carpet or bare

floors. To pick up debris it may be necessary

to move up one setting.

Medium setting – For medium pile carpet.

Highest setting – For high pile and most

shag carpet.

Note: For optimal carpet cleaning

performance, adjust to the lowest

practical setting. If your cleaner is

difficult to push, adjust to the next

higher setting.

If the dial is difficult to turn, tilt the cleaner

back slightly to take the weight off the foot

while turning.

Power switch

The power switch is located just below

the handle on the side of the vacuum.

I - ON O - OFF

Transporting cleaner

1. To move your cleaner from room to room,

put the Handle in the upright position, tilt

the cleaner back on its rear wheels and

push forward.

2. The cleaner can also be moved by using

the carrying handle.

CAUTION:

Before using your vacuum,

make sure that the dirt

container is in locked position

and that all filters (inner

circular, outer circular,

pre-motor and post-motor) are

in place. Do not operate your

vacuum without these filters.

Tip:

Your vacuum features a Quick Release cord

wrap. To remove the power cord quickly

and easily, rotate the upper cord wrap

towards floor, and slip power cord from

upper and lower cord wraps.

Tip:

Before cleaning

under low furniture,

check area first for

objects that might

harm the unit or block

the vacuum hose.

Tip:

Hair, string and

small objects can

block the vacuum

hose or tools. Check

them occasionally

for obstructions.

www.bissell.com 800.237.7691

Operations

Air flow indicator (select models only)

The air flow indicator tells you when

airflow in the vacuum is reduced due

to a clog in the hose. The indicator

will remain green until the airflow

is reduced. When it is fully red, the

airflow is significantly reduced or

blocked. Follow the steps on page

12 to clear a clog.

Special tools

Your BISSELL CleanView Helix is

not only a powerful carpet and rug

vacuum cleaner, it’s also a versatile

above floor vacuum cleaner when

you select one of the special tools.

1. Raise handle to upright position.

2. Grasp the Quick Reach handle and

lift hose wand to separate from suction

intake opening.

3. Attach tools by firmly pushing onto

vacuum hose or extension wand.

a) Crevice tool – Use in tight

narrow spaces.

b) Combination dusting

brush/upholstery tool

Two types of cleaning tools are included

in one attachment. Rotate for desired tool.

Use brush side to dust furniture, blinds,

books, lamps, shelves and baseboards.

c) Extension wand

Tip:

Hair, string and

small objects

can block the

vacuum hose or

tools. Check them

occasionally for

obstructions.

CAUTION:

The rotating floor brush continues to

rotate while tools are in use. To reduce

the risk of injury from moving parts,

always move the cleaner with the car-

rying handle at the back of the cleaner.

Always place vacuum cleaner on floor

with handle in upright position when

using tools. Never place your fingers

under the cleaner when it is running.

Never place powerfoot on furniture or

uneven surfaces. Do not place vacuum

cleaner close enough to objects to pull

them into rotating brush.

NOTICE:

The floor brush will continue to rotate

while you use your vacuum for above

floor cleaning. To prevent carpet

damage, do not lean on the vacuum

or let the powerfoot tilt forward.

www.bissell.com 800.237.7691

Operations

Power cord storage

When you have finished using your

BISSELL CleanView Helix, return it

to the upright position and store the

power cord.

1. Turn vacuum cleaner off.

2. Unplug power cord by grasping the

polarized plug (NOT the cord) and

disconnect from outlet.

3. Loop power cord around cord wraps

on side of vacuum cleaner.

4. Clip molded plug to power cord to secure.

To maintain maximum cleaning

performance, the following

maintenance steps must be performed:

1. Empty the dirt container when the dirt

reaches the “Full” line on the side.

2. Check the inner and outer circular filters

and the pre-motor filter at least once a

month and clean or replace as needed.

3. Replace the post-motor filter every six months.

Note: More frequent filter cleaning

or replacing may be necessary if

you are vacuuming new carpet,

fine dust or have allergy concerns.

Follow the instructions on the

following pages to perform these

simple maintenance steps.

Empty Dirt Container

The dirt container needs to be emptied

when the dirt reaches the “Full” line

on the side of the container.

1. Unplug cleaner from electrical outlet.

2. Slide the Lock ‘n Seal lever to the

"Unlock" position.

3. Grasp dirt cup portion handle and pull

straight out to remove from vacuum.

4. Empty dirt into garbage container.

NOTICE:

While vacuuming, certain carpets

and low humidity conditions may

generate small static discharges.

The discharges are entirely harmless

and are not associated in any way

with the main power supply.

Tip:

For maximum cleaning

performance, check

and clean or replace

all filters as suggested.

WARNING:

To reduce the risk of electric

shock, turn power switch OFF

and disconnect polarized plug

from electrical outlet before

performing maintenance or

troubleshooting checks.

Full Line

Lock Position

Unlock Position

Maintenance and care

www.bissell.com 800.237.7691

Maintenance and care

Empty Dirt Container continued

5. Put the dirt container back in the

vacuum and slide the lever to the

"Lock" position.

Note: The dirt container may be

washed in warm water with a

mild detergent. Make sure it is

completely dry before replacing.

Do not wash any components in

the dishwasher. Hand wash only.

Use only genuine BISSELL style

replacement filters in your BISSELL

CleanView Helix.

1. Unplug the cleaner from electrical outlet.

2. a) Remove the dirt container as

described in the previous section.

b) Grasp the filter cup located at the

bottom of the dirt container. Lift up

and out. DO NOT TRY TO PULL THE

CIRCULAR FOAM FITLER OUT OF

THE FILTER CUP WHILE IT IS STILL IN

THE VACUUM.

3. Grasp the plastic tab on the top of the

circular foam filters. Twist to unlock and

pull out.

4. Separate the outer foam and inner pleated

circular filters. Wash each individually by

hand in warm water. Mild detergent may

be used if desired. Rinse well, then air

dry thoroughly before putting them back

together and replacing in filter cup.

5. The filter cup may be washed in warm

water with a mild detergent. Make sure

it is completely dry before reassembling

with filters.

6. The upper tank and louvers may also be

wiped clean with a damp cloth. Reach

underneath the upper tank and turn the

rim of the louvers to unlock. Pull straight

down to remove. Make sure all parts

are dry before replacing.

2a.

2b.

Cleaning the inner & outer circular filter

www.bissell.com 800.237.7691

Maintenance and care

Cleaning the pre-motor filter

1. Unplug the cleaner from electrical outlet.

2. The pre-motor filter protects the motor

from debris. It is located underneath the

filter cup in the center of the round part

of the Lock ‘n Seal lever.

3. Remove the small round filter and any

debris on top of it. Rinse well under

warm water, then air dry thoroughly

before replacing.

Replacing the post-motor filter

Use only genuine BISSELL style 9

(#32076) replacement filters in your

BISSELL CleanView Helix.

1. Unplug the cleaner from electrical outlet.

2. The post-motor filter assists in the filtration

process to return clean air to the room.

It is located behind the door on the side

of the vacuum. When the filter becomes

dirty, open the door, remove the filter and

replace. The white, pleated HEPA Media

Filter* is not washable.

Note: A basic washable

post-motor filter with reduced

filtration is available if desired.

You should check your vacuum cleaner’s

rotating floor brush and drive belt

regularly for wear or damage. You

should also clean the brush and brush

ends of strings, hair and carpet fibers.

These can wrap around the brush and

hamper its ability to effectively clean

your carpet. Also remove any debris

that has accumulated under the

brush cover.

1. Unplug cleaner from electrical outlet.

2. Place handle in low position and turn

vacuum cleaner over so bottom side is up.

3. Remove the five screws with a Phillips

head screwdriver. Lift the brush cover off.

4. Grasp rotating floor brush at both ends and lift.

Post-Motor

Filter

WARNING:

Do not operate cleaner

with damp or wet filters or

without all filters in place.

WARNING:

To reduce the risk of injury from

moving parts, turn off vacuum

cleaner and disconnect Power

Plug from electrical outlet.

Pre-Motor

Filter

Motor Pulley

Checking rotating floor brush and drive belt

Brush Cover

*The filter media, not the vacuum as a whole,

complies with IEST-RP-CC001.5 HEPA standard.

www.bissell.com 800.237.7691

Maintenance and care

5. Clean strings, hair and other debris from

rotating floor brush, paying particular

attention to brush ends.

6. Clean strings, hair and other

debris from motor pulley and

drive belt areas.

7. Check drive belt carefully for wear,

cuts or stressed areas.

8. Check air passageway for obstructions.

Remove debris from this area.

Replace drive belt

Use only genuine BISSELL style 9

replacement belts (#203-1093) in

your BISSELL CleanView Helix.

1. Unplug cleaner from electrical outlet.

2. With rotating floor brush removed from

vacuum cleaner (steps 1-4 of Check

rotating floor brush and drive belt),

grasp old drive belt and remove from

motor pulley. Discard old drive belt.

3. Place new drive belt over motor

pulley and stretch other end over

rotating floor brush in the space

between the bristles.

4. Place ends of rotating floor brush

down into slots on sides as shown.

5. Turn rotating floor brush by hand

several times in the direction of motor

pulley. If properly installed, drive belt

will center itself on rotating brush.

6. Reposition brush cover and screw

back into place.

Air Passageway

Motor

Pulley

Checking rotating floor brush and drive belt continued

www.bissell.com 800.237.7691www.bissell.com 800.237.7691

Clearing a clog

Low suction or poor pickup may be

due to a clog in the vacuum cleaner.

If you notice a change in the sound

of the motor or a reduction in the

spinning action, check for clogs.

1. Unplug cleaner from electrical outlet.

2. Empty dirt container.

3. Check upper tank for build up or clogs.

4. Check the suction inlet for a clog.

5. Grasp the quick reach handle and

lift hose wand to separate from the

suction opening. Check for a clog

in the base, the wand or the hose.

6. Remove the screw attaching the hose

wand base to the vacuum. Straighten the

hose wand base and unclog with long,

narrow object such as a broom stick.

7. If the clog persists, follow the

instructions for Checking the rotating

floor brush on page 10 and inspect

the air passageway for obstructions.

Replace light bulb

Use only BISSELL Replacement Bulbs

in your BISSELL CleanView Helix.

selected models only

1. Unplug cleaner from electrical outlet.

2. Using a flat screwdriver, table knife or

coin, insert into the slot on the right of

the lens and gently push inner latch to

the left as shown to remove the lens.

3. Reposition lens by inserting the tab

on left side and then pushing the right

side back into place.

Maintenance and care

Suction Inlet

Remove Screw

www.bissell.com 800.237.7691

Vacuum cleaner won’t turn on

Possible causes Remedies

1. Power cord not plugged in 1. Check electrical plug

2. Blown fuse/tripped breaker 2. Check/replace fuse or reset breaker

Vacuum cleaner won’t pick up dirt

Possible causes Remedies

1. Incorrect height adjustment 1. Adjust powerfoot to correct height setting

2. Hose not attached to suction opening 2. Grasp quick reach handle and firmly push

hose wand onto the suction opening

3. Crack or hole in hose 3. Check hose and replace if needed

4. Broken or worn drive belt 4. Replace drive belt, see page 11

5. Rotating floor brush bristles worn 5. Replace brush

6. Rotating floor brush jammed 6. Remove brush and clean debris from brush ends,

see page 10

7. Clog in vacuum 7. Follow instructions on page 12 for clearing clogs

8. Dirt container full 8. Empty dirt container, see page 8

9. Dirt container or upper tank not installed properly 9. Position correctly and lock in place

10. Filters are dirty 10. Check and clean pre-motor and post-motor filters,

see page 10

Tools won't pick up dirt

Possible causes Remedies

1. Crack or hole in hose 1. Check hose and replace if needed

2. Clog in vacuum 2. Follow instructions on page 12 for clearing clogs

3. Dirt container full 3. Empty dirt container

4. Dirt container or upper tank not installed properly 4. Position correctly and lock in place

5. Filters are dirty 5. Check and clean pre-motor and post-motor filters

Vacuum cleaner is difficult to push

Possible causes Remedies

1. Incorrect height adjustment 1. Adjust powerfoot to correct height setting

Visible dirt escaping from cleaner

Possible causes Remedies

1. Dirt container full 1. Empty dirt container, see page 8

2. Filters missing or installed incorrectly 2. Check pre-motor and post-motor

filters for correct installation

Please do not return this product to the store.

For any questions or concerns, BISSELL is happy to be of service.

Troubleshooting - CleanView Helix

WARNING:

To reduce the risk of injury from

moving parts, turn off vacuum

cleaner and disconnect from

power outlet before performing

troubleshooting steps.

Other maintenance or service not included

in the manual should be performed by an

authorized service representative.

Thank you for selecting a

BISSELL product.

www.bissell.com 800.237.7691

Accessories - CleanView Helix

Replacement Parts - CleanView Helix

Warranty - BISSELL CleanView Helix

22C1 and 32Y7

This warranty gives you specific legal rights, and you may also have other rights which may vary from state

to state. If you need additional instruction regarding this warranty or have questions regarding what it may

cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.

Limited Two Year Warranty

Subject to the EXCEPTIONS AND EXCLUSIONS identified on page 15, upon receipt of the

product BISSELL will repair or replace (with new or remanufactured components or products),

at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for two

years any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This

warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes.

Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other

use not in accordance with the user's guide is not covered.

See information on page 15 "If your BISSELL product should require service:"

*The filter media, not the vacuum as a whole, complies with the IEST-RP-CC001.5 HEPA Standard.

Item Part No. Part Name

1 203-2447 TurboBrush Tool

2 203-1063 Crevice Tool

3 203-1059 Combination Dusting/Upholstery Brush

4 203-1084 Extension Wand

*Not all parts are included with every model.

2 4 5

6 7

3 4

These items are available for purchase as accessories for your BISSELL

CleanView Helix. To purchase call 1-800-237-7691 or visit www.bissell.com.

Item Part No. Part Name

1 203-1093 Style 9 Drive Belt (2-Pack)

2 203-1297 Standard Headlight Bulb (selected models only)

3 203-2450 Hose Assembly

4 203-2449 Brush Dowel (15")

5 32R9 Style 16 Inner and Outer Circular Pre-Motor Filter Set

6 203-1464 Style 16 Inner Circular Pre-Motor Filter

7 203-1192 Style 16 Outer Circular Pre-Motor Filter

8 32076 Style 7/9/16 HEPA Media Filter*

9 3099 Style 7/9/16 Post-Motor Filter

www.bissell.com 800.237.7691

Warranty-BISSELL CleanView Helix

22C1-2, 21K3,

71V9, 71V9-2

This warranty gives you specific legal rights, and you may also have other rights which may

vary from state to state. If you need additional instruction regarding this warranty or have

questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,

telephone, or regular mail as described below.

Limited Three Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product

BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s

option, free of charge from the date of purchase by the original purchaser, for three years any

defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This

warranty does not apply to fans or routine maintenance components such as filters, belts, or

brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair,

or any other use not in accordance with the user's guide is not covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.

If you need information about repairs or replacement parts, or if you have questions about

your warranty, contact BISSELL Consumer Services.

Website or E-mail:

www.bissell.com

Or Call:

BISSELL Consumer Services

1-800-237-7691

Monday – Friday 8 am - 10 pm ET

Saturday 9 am - 8 pm ET

Or Write:

BISSELL Homecare, Inc.

PO Box 1888

Grand Rapids, MI 49501

ATTN: Consumer Services

BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE

ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE

PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR

WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE

LIMITED TO THE WARRANTY DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow warranty limitations on how long an implied warranty last so the above

limitation may not apply to you.

Grand Rapids, Michigan

Part Number 110-4459

Rev 12/11

Visit our website at:

www.bissell.com

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services

1-800-237-7691

Monday – Friday 8 am - 10 pm ET

Saturday 9 am - 8 pm ET

Or write:

BISSELL Homecare, Inc.

PO Box 1888

Grand Rapids MI 49501

ATTN: Consumer Services

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt.

It provides proof of purchase date in the event

of a warranty claim. See Warranty on pages

14 and 15 for details.

BISSELL consumer services

www.bissell.com 800.237.7691

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

Bissell CleanView Helix 22C1 Series Instrukcja obsługi

Marka: Bissell

Model: CleanView Helix 22C1 Series

Kategoria: Odkurzacze

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

ściągnij PDF

raport

w innych językach

English: Bissell CleanView Helix 22C1 Series User manual

Bissell CleanView Helix 22C1 Series Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Bissell CleanView Helix 22C1 Series Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty