Pella 801U0103 Instrukcja obsługi

Marka: Pella

Model: 801U0103

Typ: Instrukcja obsługi

Installation Instructions for Typical Wood Frame Construction.

These instructions were developed and tested for use with typical wood frame wall construction

in a wall system designed to manage water. These instructions are not to be used with any other

construction method. Installation instructions for use with other construction methods, multiple

units or bow and bay windows, may be obtained from Pella Corporation, a local Pella retailer, or

by visiting http://www.pella.com. Building designs, construction methods, building materials,

and site conditions unique to your project may require an installation method different from

these instructions and additional care. Determining the appropriate installation method is the

responsibility of you, your architect, or construction professional.

Part Number: 801U0103

Always read the Pella® Limited Warranty before purchasing or installing

Pella products. By installing this product, you are acknowledging that this

Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation

and maintenance instructions may void your Pella product warranty. See Limited Warranty for

complete details at http://warranty.pella.com.

INSTALLATION INSTRUCTION STANDARD, PERFORMANCE

UPGRADE AND HURRICANESHIELD

IMPACT RESISTANT FOR

FIXED FRAME DIRECT SET WINDOWS

8JOEPX#PUUPN

8JOEPX5PQ

/BJMJOH'JO

'JO$PSOFS

8BUFS3FTJTUJWF#BSSJFS

4IFBUIJOH

'SBNJOH

5PQ

'MBTIJOH

5BQF

0VUFS$PSOFS

'MBTIJOH5BQF

0VUFS

7FSUJDBM

'MBTIJOH

5BQF

4JEF

'MBTIJOH

5BQF

4JEF

'MBTIJOH

5BQF

4JMM'MBTIJOH5BQF

4JMM'MBTIJOH5BQF

0VUFS

7FSUJDBM

'MBTIJOH

5BQF

Instrucciones enspañol en el reverso.

YOU WILL NEED TO SUPPLY: TOOLS REQUIRED:

ŘCedar or Impervious shims/spacers (12 to 20)

Ř2" galvanized rooﬁng nails (1/4 lb.)

Note: Performance Upgrade and HurricaneShield® units

require use of installation clips or screws through the frame.

ŘClosed cell foam backer rod/sealant backer (12 to 30 ft.)

ŘPella® SmartFlash™ foil backed butyl window

and door ﬂashing tape or equivalent

ŘPella Window and Door Installation Sealant or equivalent

high quality, multi-purpose sealant (1 tube per window)

ŘLow expansion, low pressure polyurethane insulating

window and door foam sealant - DO NOT use high

pressure or latex foams

ŘInterior trim and/or jamb extensions (15 to 40 ft.)

ŘTape measure

ŘLevel

ŘSquare

ŘHammer

ŘStapler

ŘScissors or utility knife

ŘSealant gun

4&"-"/5

C. Cut the water resistive barrier (1C). See page 10 for

additional cutting patterns.

D. Fold the water resistive barrier (1D). Fold side ﬂaps into

the opening and staple to inside wall. Fold top ﬂap up and

temporarily fasten with ﬂashing tape.

E. Apply sill ﬂashing tape #1. Cut a piece of ﬂashing tape

12" longer than the opening width. Apply at the bottom of

the opening as shown (1E) so it overhangs 1" to the exterior.

Note: The tape is cut 12" longer than the width so that it will extend 6" up

each side of the opening.

F. Tab the sill ﬂashing tape

and fold. Cut 1" wide tabs at

each corner (1/2" from each

side of corner) (1F). Fold tape

to the exterior and press

ﬁrmly to adhere it to the

water resistive barrier.

G. Apply sill ﬂashing tape #2.

Cut a piece of ﬂashing tape

12" longer than the opening width. Apply at the bottom, overlapping tape #1 by at

least 1". Do not allow the tape to extend past the interior face of the framing (1G).

Note: The ﬂashing tape may not fully cover the framing members.

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.

A. Make sure the bottom of the opening is level.

Note: It is critical the bottom is level for the window to be

installed correctly.

B. Conﬁrm the window will ﬁt in the opening. Measure all four

sides of the opening;

Standard units: Opening is to be 3/4" larger than the window

in both width and height.

Performance Upgrade and HurricaneShield: Opening is

to be 1/2" larger than the window in both width and height.

On larger openings measure the width and height in several

places to conﬁrm the header or studs are not bowed.

Note: 1-1/2" or more of solid wood blocking is required

around the perimeter of the opening. Fix any problems

with the rough opening before proceeding.

ROUGH OPENING PREPARATION

*OUFSJPS

£

£

*OUFSJPS



DVU

.BLFBDVUVQGSPN

FBDIUPQDPSOFSBUB¡

BOHMFUPBMMPXUIFXBUFS

SFTJTUJWFCBSSJFSUPCF

MBQQFEPWFSUIFmOBUUIF

IFBEPGUIFXJOEPX





DVU



DVU

8BUFS3FTJTUJWF#BSSJFS



DVU

$VUEPXOUPNFFUUIF

¡DVUPOFBDIDPSOFS

£



DVU

Exterior

£







£



£

ŘWINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS ŘALL

A. Install and level shims. Place 1" wide by 1/4" thick shims

on the bottom of the opening, 2-1/2" from each side,

beneath transition bars and mullion joints. Keep shims

back 1/2" from interior face of window. Adjust shims as

necessary to ensure the sill is level. Once level, attach

shims to prevent movement.

Note: Improper placement of shims may result in

bowing the bottom of the window.

B. Remove plastic wrap and cardboard packaging from window.

Note: If grilles are removed from the window at this time, label them and store

them in a protected area.

SETTING AND FASTENING THE WINDOW

C. Units with fold-out installation ﬁns: Fold out ﬁn to 90°. On units with pre-applied

ﬁn corners, be careful not to remove or tear the ﬁn corners.

Note: If the ﬁn is not at 90°, the window will not line up correctly on the interior.

ŘWINDOW Ř ALL WINDOWS Ř ALL WINDOWS Ř

D. Windows using Installation Clips: Install installation

clips. If installation ﬁns are used; place the clip so that

the lip is facing up and against the installation ﬁn, at the

locations shown in the placement diagram. If installation

ﬁns are not used, the clip lip faces down and is inserted

into a groove in the frame. Secure the clip by driving

#6 x 5/8" corrosion resistant screws through the outer

two holes of the three holes shown.

MAX

10"

MAX

10"

MAX

10"

MAX

10"

MAX

10"

MAX

FOR PLACEMENT

OF FRAME

SCREWS AND

INSTALLATION

CLIPS

$MBE'SBNF4JMM

%SJMM

DMFBSBODFIPMF



#

E. Windows using frame screws: Pre-drill installation

screw holes. On the room side of the window, drill

13/64" diameter clearance holes through the frame

as shown on the placement diagram. Space the holes

a maximum of 6" from each end and a maximum of

10" on center on the head, jambs and sill.

Ó

#

¡

$*3$-&)&"%8*5)

'-&9*#-&'*/

6“ from end

Lip

#6 x 5/8” corrosion

resistant screws

PERFORMANCE UPGRADE & HURRICANESHIELD

Note: Performance Upgrade and HurricaneShield® require

use of installation clips or screws through the frame.

Use of ﬁns in addition to clips or screws is optional.

F. Insert the window from the exterior of the building. Place the bottom of

the window on the spacers at the bottom of the opening, then tilt the top into

position. Center the window between the sides of the opening to allow clearance

for shimming.

Windows with nail ﬁn: Insert one rooﬁng nail in the ﬁrst hole from the corner on

each end of the top nailing ﬁn. These are used to hold the window in place while

shimming it plumb and square.

Windows using screws through the frame: Position the window so the exterior

face of the frame extends 3/4" on the exterior wall material to allow for the

application of backer rod and sealant (See illustrations in Step 7 for sealant

details). Center window between the sides of the opening to allow clearance for

shimming and insert one #10 x 3-1/2" screw into each of the top clearance holes.

This will hold the window in place while shimming it plumb and square.

Window with Installation Clips: Position the window so the exterior face of

the frame extends 3/4" on the exterior wall material to allow for the application

of backer rod and sealant (See illustrations in Step 7 for sealant details). Center

window between the sides of the opening to allow clearance for shimming and

insert one #6 x 1-1/2" or longer screw into one hole in each of the top corner

clips. This will hold the window in place while shimming it plumb and square.

Note: For masonry openings use 3/16" x 1-1/2" masonry screw.

SETTING AND FASTENING THE WINDOW

(CONTINUED)

TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLLOWING STEPS.

ŘWINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS ŘALL

G. Plumb and square the window. Place

shims 1" from the bottom and top of the

window between the window and the sides

of the opening. Keep shims back 1/2"

from the interior face of the window.

Adjust the shims as required to

plumb and square the window in

the opening. If the frame height

exceeds 53", place shims at the

midpoint of the window sides.

Note: DO NOT shim above the

window or in the space between the

spacers at the bottom of the window. DO NOT over shim.

H. Check the interior reveal. Make sure the measurement from the interior

face of the window to the interior face of the wall is equal at several points

around the window.

Note: If the dimensions are not equal, check to make sure the ﬁns are

folded out to 90˚ at all points.

30 40

INCHES

A. Units that do not have pre-applied

ﬁn corners: Cut four pieces of

ﬂashing tape 1-1/2" long. Apply one

piece of ﬂashing tape to each end of

the sill ﬁn so that it extends 1-1/2" past

the end of the sill ﬁn. Apply one piece

of ﬂashing tape to the bottom end

of each ﬂexible ﬁn, beginning 1-1/2"

from the end of the ﬁn, and lapping

over the ﬂashing tape that extends

from the end of the sill ﬁn.

INTEGRATING THE WINDOW TO THE WATER

RESISTIVE BARRIER

Î



Î



ŘWINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS ŘALL

Î



B. Apply side ﬂashing tape. Cut two pieces of ﬂashing

tape 4" longer than the frame height of the window.

Apply one piece 1/2" up onto the frame cladding over

the nailing ﬁn and onto the water resistive barrier to

each side. The tape should extend 2" above the top of

the window and 2" below the bottom of the window.

Press the tape down ﬁrmly while folding down the

excess tape at the top and bottom of the window.

Note: DO NOT tape or seal the bottom nailing ﬁn.

C. Apply top ﬂashing tape. Cut a piece of

ﬂashing tape long enough to go across the

top of the window and extend at least 1"

past the side ﬂashing tape on both sides.

Apply the tape 1/2" up onto the frame

cladding over the top nailing ﬁn as shown.

Fold the overlapping tape down, and press

all tape down ﬁrmly.

Î



Ó

Ó

'JYFE

&YUSVEFE'JO

I. Fasten the window to opening. On

windows with a ﬁxed extruded ﬁn, drill

1/8 diameter holes in the ﬁn every 12".

Windows with Nail Fin:

J. Drive a 2" galvanized rooﬁng nail

into each of the pre-punched and pre-

drilled holes.

For ﬂexible ﬁn: Drive nails until the head

contacts the ﬁn, however do not sink the head.

This allows for movement of building materials.

Note: Make sure all ﬁn corners are lying as

ﬂat as possible.

SETTING AND FASTENING THE WINDOW

(CONTINUED)

Note: Step 3 applies to windows with installation ﬁns used in

combination with a water resistive barrier.

D. Fold down top ﬂap of water resistive barrier (3D).

E. Apply ﬂashing tape to diagonal cuts. Cut

pieces of ﬂashing tape at least 1" longer than the

diagonal cuts in the water resistive barrier. Apply

the tape covering the entire diagonal cut in the

water resistive barrier at both upper corners of

the window. If vertical cuts were also made, apply

ﬂashing tape to them in the same manner.

Note: The top tape must overlap the tape below

it to divert water properly. Be sure to overlap

the top corners (3E).

INTEGRATING THE WINDOW TO THE WATER

RESISTIVE BARRIER (CONTINUED)

Note: If installing the window using

installation clips, proceed to Step 5 -

Installation Clip Method.

&YUFSJPS

Î

Î

C1. Apply top ﬂashing tape to circle top windows. Several pieces of ﬂashing tape

will be needed to cover the top ﬁn. Start taping from the sides of the window

working toward the peak. To determine the length of cuts, hold the tape along the

radius, and cut the tape just past where it leaves the top ﬁxed extruded ﬁn or for the

ﬂexible ﬁn, just past the ﬂexible weather strip. The top tape must overlap the one

beneath it in order to divert water properly. The sharper the arc of the window, the

shorter the pieces of tape will be.

3C1

C2. Apply top ﬂashing tape to an angle top window 1/2" up onto the frame

cladding, over the top ﬁn onto the sheathing. On the short side of a trapezoid

window, do not allow the side ﬂashing tape to extend higher than what the top

tape will cover. Fold the overlapping tape down, and press all tape down ﬁrmly.

ŘWINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS ŘALL

SECURING THE WINDOW

A. Install a #10 x 3-1/2" corrosion

resistant wood screw into each pre-

drilled screw hole.

Note: Minimum 1-1/4" embedment

into the wall framing is required.

Proceed to Step 6.

ŘALL WINDOWS Ř ALL WINDOWS Ř

INSTALLATION CLIP METHOD

A. Fasten the window to the opening by driving two

#6 x 1-1/2" or longer corrosion resistant screws into

the pre-punched holes in the clips. If clips are bent and

fastened to the interior stud/block, install the screws as

close to the bend as possible.

Note: DO NOT shim above the window.

INTERIOR

#10 x 3-1/2"

corrosion

resistant

wood screw

Caution: Ensure use of low pressure polyurethane window and door insulating

foams and strictly follow the foam manufacturer’s recommendations for

application. Use of high pressure foams or improper application of the foam may

cause the window frame to bow and hinder operation.

INTERIOR SEAL

{

A. Apply insulating foam sealant. From the interior, insert

the nozzle of the applicator into the space between the

window and the rough opening approximately 1" past

the edge of the frame (and past the jamb extensions)

and apply a 1" deep bead of foam. This will allow room

for expansion of the foam and will minimize squeeze

out. Apply sealant across the interior surface of the

shims to create a continuous seal. Follow foam

manufacturer's instructions.

Note: DO NOT place any foam between jamb

extensions and the rough opening.

Note: DO NOT completely ﬁll the space from the

back of the ﬁn to the interior face of the opening.

ŘPERFORMANCE UPGRADE & HURRICANESHIELD WINDOWS Ř

SEALING THE WINDOW TO THE

EXTERIOR WALL CLADDING

When applying siding, brick veneer or other exterior ﬁnish material, leave

adequate space between the window frame and the material for sealant. Refer to

the illustration that corresponds to your ﬁnish material.

Note: The sealant details shown are standard recommendations from the sealant

industry. Contact your sealant supplier for recommendations and instructions for

these and any other applications.



7*/:-45&&-

4*%*/(

$MFBSBODF

#BDLFS3PEBOE

4FBMBOUUZQJDBM

*OTVMBUJOH

'PBN

1FSJNFUFS4FBMBOU

NVTUFYUFOEUP

SPPNTJEFPG

"DDFTTPSZ(SPPWF

"DDFTTPSZ(SPPWF

800%4*%*/(

8*5)53*.

*OTVMBUJOH

'PBN



.JO



$MFBSBODF

1FSJNFUFS4FBMBOU

NVTUFYUFOEUP

SPPNTJEFPG

"DDFTTPSZ(SPPWF

"DDFTTPSZ(SPPWF

4FBMBOUUZQJDBM



.JO

#3*$,7&/&&3

$MFBSBODF

#BDLFS3PEBOE

4FBMBOUUZQJDBM

1FSJNFUFS4FBMBOU

NVTUFYUFOEUP

SPPNTJEFPG

"DDFTTPSZ(SPPWF

"DDFTTPSZ(SPPWF

*OTVMBUJOH

'PBN

800%

4*%*/(

*OTVMBUJOH

'PBN



$MFBSBODF

4FBMBOUUZQJDBM



.JO

ŘWINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS ŘALL

A. Insert closed cell foam backer rod into

the space around the window so there is

approximately 3/8" clearance between the

backer rod and the exterior face of the window.

Note: Backer rod adds shape and depth for

the sealant line.

x

x

B. Apply a bead of high quality exterior grade

sealant to the entire perimeter of the window.

Note: For wood siding applications, when using

the ﬂexible ﬁn, ensure the sealant bead covers the

exterior edge of the ﬁn weather-strip.

C. Shape, tool and clean excess sealant. When

ﬁnished, the sealant should be the shape of

an hourglass.

INTERIOR FINISHING

If products cannot be ﬁnished immediately, cover with clear plastic to protect from

dirt, damage and moisture. Remove any construction residue before ﬁnishing. Sand

all wood surfaces lightly with 180 grit or ﬁner sandpaper. DO NOT use steel wool. BE

CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust.

Note: To maintain proper product performance do not paint, ﬁnish or remove the

weather-stripping, mohair dust pads, gaskets or vinyl parts. Air and water leakage

will result if these parts are removed. After ﬁnishing, allow venting windows and

doors to dry completely before closing them.

Pella Corporation is not responsible for interior paint and stain ﬁnish imperfections

for any product that is not factory-applied by Pella Corporation. Use of inappropriate

ﬁnishes, solvents, brickwash, or cleaning chemicals will cause adverse reactions with

window and door materials and voids the Limited Warranty.

For additional information on ﬁnishing see the Pella Owner's Maual or go to

www.pella.com.

SEALING THE WINDOW TO THE

EXTERIOR WALL CLADDING (CONTINUED)

ŘWINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS Ř ALL WINDOWS ŘALL

Note: This method creates a more ﬂexible

sealant line capable of expanding and contracting.

EXTERIOR FINISH

The exterior frame and sash are protected by aluminum cladding with our EnduraClad® or

EnduraClad Plus baked-on factory ﬁnish that needs no painting. Clean this surface with mild

soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT

use abrasives. DO NOT scrape or use tools that might damage the surface.

Use of inappropriate ﬁnishes, solvents, brickwash or cleaning chemicals will cause adverse

reactions with window and door materials and voids the Limited Warranty.

CARE AND MAINTENANCE

Care and maintenance information is available in the Pella Owner’s Manual. You can

obtain an owner’s manual by contacting your local Pella retailer. This information is also

available on www.pella.com.

IMPORTANT NOTICE

Because all construction must anticipate some water inﬁltration, it is important that the wall

system be designed and constructed to properly manage moisture. Pella Corporation is not

responsible for claims or damages caused by anticipated and unanticipated water inﬁltration;

deﬁciencies in building design, construction and maintenance; failure to install Pella products

in accordance with Pella’s installation instructions; or the use of Pella products in wall

systems which do not allow for proper management of moisture within the wall systems. The

determination of the suitability of all building components, including the use of Pella products,

as well as the design and installation of allow for proper management of moisture within the

wall systems. The determination of the suitability of all building components, including the

use of Pella products, as well as the design and installation of ﬂashing and sealing systems are

the responsibility of the Buyer or User, the architect, contractor, installer, or other construction

professional and are not the responsibility of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper

management of moisture within the wall systems, such as barrier Exterior Insulation and Finish

Systems, (EIFS) (also known as synthetic stucco) or other non-water managed systems. Except

in the states of California, New Mexico, Arizona, Nevada, Utah, and Colorado, Pella makes no

warranty of any kind on and assumes no responsibility for Pella windows and doors installed in

barrier wall systems. In the states listed above, the installation of Pella Products in barrier wall or

similar systems must be in accordance with Pella’s installation instructions.

Product modiﬁcations that are not approved by Pella Corporation will void the Limited Warranty.

$JSDMF)FBE

'VMM$JSDMF

5SBQF[PJE

0DUBHPO

"SDI)FBE 3FDUBOHMF

2VBSUFS$JSDMF

)BMG$JSDMF

0WBM

%PH)PVTF

3JHIU5SJBOHMF

Additional cutting patterns

Pella 801U0103 Instrukcja obsługi

Marka: Pella

Model: 801U0103

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

English: Pella 801U0103 User manual

Pella 801U0103 Instrukcja obsługi

Pella 801U0103 Instrukcja obsługi

w innych językach

Inne dokumenty