Andersen 200 Series - Tilt-Wash Hung - 0005314 Service Instructions
- Typ
- Service Instructions
Andersen® 200 Series Tilt-Wash Double-Hung Windows Hardware Replacement Kit
1
“Andersen”, the AW logo, and “Andersen WindowCare” are registered trademarks of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation.
©2002 Andersen Corporation. All rights reserved. Instruction Guide 0005314 Revised 12/06/02
Colored #6 x 1" Screw
Operating Instruction Label
Hardware Replacement
for Andersen® 200 Series Tilt-Wash Double-Hung Windows
Parts Included
(4) Sliding Tilt Latch
(1) Keeper
(2) Keeper Clips
(2) Colored #6 x 1” Screws
(2) #5 x 3/4” Screws
(4) 8-15 x 5/8” Truss Head Screws
(1) Operating Instruction Label
Tools Required for Procedure
• Safety Glasses
• Phillips-head Screwdriver
Sliding Tilt
Latch Keeper
Keeper
Clips
Support sash during replacement procedure. Failure to support sash may result in personal injury, product,
and/or property damage.
#5 x 3/4" Screw
3"
Pay close attention
to safety warning.
Unlock and raise bottom
window 3 inches.
Slide tilt latches towards
center of window.
Tilt bottom
window inward.
Hold window
firmly until
supported on a
chair or object
at a 30/40°
angle.
1
Steps for Tilting & Cleaning
2
After washing, tilt
top window back
into frame.
Push top of window
back and forth to
make sure latches
are engaged in
frame.
Repeat
steps
4 and 5
for
bottom
window.
If window is not
re-engaged in the
track by first
pushing DOWN on
window, window
will quickly drop
causing injury.
Lower top window
down and slide tilt
latches towards
center of window.
Tilt top window
inward.
IMPORTANT!
Window MUST
be pushed
DOWN about
1 inch BEFORE
sliding to top of
frame.
No. 7700830 Revised 11/01
56
WARNING
34
Weight of window and door
unit(s) and accessories will vary.
Use a reasonable number of
people with suffi cient strength to
lift, carry, and install window and
door unit(s) and accessories.
Always use appropriate lifting
techniques.
Use of ladders and/or scaffolding and
working at elevated levels may be
hazardous. Follow equipment
manufacturer's instructions for safe
operation. Use extreme caution when
working around window and door
openings. Falling from opening may
result in personal injury or death.
Improper use of hand or
power tools could result in
personal injury and/or
product damage. Follow
equipment manufacturer's
instructions for safe
operation. Always wear
safety glasses.
Read all instructions carefully before attempting this procedure. If you have any questions about your ability to
complete this procedure, call Andersen at 1-888-888-7020 for further direction. Andersen WindowCare®
service center hours are Monday through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m.
Central Time. Thank you for choosing Andersen® products.
8-15 x 5/8” Truss Head Screw
Andersen® 200 Series Tilt-Wash Double-Hung Windows Hardware Replacement Kit
2
1. Remove and Replace Upper Sash/Window Tilt Latches
• Unlock Window and raise Lower Sash/Window about
3” from sill.
• Remove Tilt Latch Screw, if present, in Lower
Sash/Window Tilt Latches.
• Raise Tilt Latches in Lower Sash/Window and tilt Lower
Sash/Window until supported on chair or object.
• Lower Upper Sash/Window approximately 6”.
• Raise Tilt Latches in Upper Sash/Window and tilt Upper
Sash/Window inward, supporting Upper Sash/Window
at all times.
• DO NOT remove gold colored Balance Screw
• Properly dispose of existing Tilt Latch and Screw
as they are removed.
• Close Upper Sash/Window Tilt Latch to expose
recessed White or Stone Colored Screw holding
existing Upper Sash/Window Tilt Latch. Remove White
or Stone Colored Screw and discard properly.
Upper
Sash/Window
Tilt Latches
Remove
Tilt Latch
Replacement
Sliding Tilt Latch
Remove
Replace
DO NOT Remove
Gold Colored Screw
DO NOT Remove
Gold Colored Screw
If Sash/Window balance is not re-engaged in the
track by fi rst pushing down on the Sash/Window,
it will quickly drop potentially causing injury.
• Return Upper Sash/Window to closed position, check
for Tilt Latch engagement in Jamb Channel by pushing
back and forth. Push Upper Sash/Window down
approximately 1” to engage Sash Balances.
Remove
Colored
3/4” Screw
Replacement
8-15 x 5/8”
Truss Head Screw
• Remove existing Upper Sash/Window Tilt Latch and
properly discard. Replace with new Upper Sash/
Wi ndow Sliding Tilt Latch and fasten using a
8-15 x 5/8” Truss Head Screw, provided. Repeat for
opposite Upper Sash/W i ndow Tilt Latch.
Make sure Sliding Tilt Latches
are oriented and seated
correctly in Tilt Latch Pocket
on Sash/Window. When
viewing Sliding Tilt Latches
from the top (as shown),
beveled edge must be
positioned to the exterior.
Remove Tilt
Latch Screw
(if present)
Exterior
Side
Interior
Side
Interior View
Andersen® 200 Series Tilt-Wash Double-Hung Windows Hardware Replacement Kit
3
2. Remove and Replace Keeper
• Close Lower Sash Tilt Latch to expose recessed White
or Stone Colored Screw holding existing Lower
Sash/W i ndow Tilt Latch. Remove White or Stone
Colored Screw and discard.
• Remove and dispose of existing Keeper and Screws
using a Phillips screwdriver.
• Install replacement Keeper using two Colored
#6 X 1” Screws, provided.
• Do Not remove gold colored Balance Screw
• Properly Dispose of existing Tilt Latch and Screw
as they are removed.
Lower
Sash/
Window
Tilt
Latches
Replacement
Sliding Tilt Latch
Remove
Replace
DO NOT Remove
Gold Colored Screw
DO NOT Remove
Gold Colored Screw
• Raise Lower Sash/Window to a comfortable working
position and support on chair or object.
3. Replace Lower Sash/Window Tilt Latches
Keeper
• Remove existing Lower Sash/W i ndow Tilt Latch and
discard. Replace with new Lower Sash/Window Sliding
Tilt Latch and fasten using a 8-15 x 5/8” Truss Head
Screw, provided. Repeat for opposite Lower Sash/
Wi ndow Tilt Latch.
Remove
Tilt Latch
Make sure Sliding Tilt Latches
are oriented and seated
correctly in Tilt Latch Pocket
on Sash/Window. When
viewing Sliding Tilt Latches
from the top (as shown),
beveled edge must be
positioned to the exterior.
Exterior
Side
Interior
Side
Keeper
Interior View
Interior View
Remove
Colored
3/4” Screw
Replacement
8-15 x 5/8”
Truss Head Screw
Andersen® 200 Series Tilt-Wash Double-Hung Windows Hardware Replacement Kit
4
5. Replace Operating Instruction Label
• Remove existing Operating Instruction Label located on
head jamb and replace with replacement Operating
Instruction Label.
Replacement Operating Instruction Label
4. Install Keeper Clips and Lock
3"
Pay close attention
to safety warning.
Unlock and raise bottom
window 3 inches.
Slide tilt latches towards
center of window.
Tilt bottom
window inward.
Hold window
firmly until
supported on a
chair or object
at a 30/40°
angle.
1
Steps for Tilting & Cleaning
2
After washing, tilt
top window back
into frame.
Push top of window
back and forth to
make sure latches
are engaged in
frame.
Repeat
steps
4 and 5
for
bottom
window.
If window is not
re-engaged in the
track by first
pushing DOWN on
window, window
will quickly drop
causing injury.
Lower top window
down and slide tilt
latches towards
center of window.
Tilt top window
inward.
IMPORTANT!
Window MUST
be pushed
DOWN about
1 inch BEFORE
sliding to top of
frame.
No. 7700830 Revised 11/01
56
WARNING
34
Replacement
Keeper Clip
Replacement
#5 x 3/4”
Screws
Lock*
*Lock style may vary
If Sash/Window balance is not re-engaged in the
track by fi rst pushing down on the Sash/Window,
it will quickly drop potentially causing injury.
• Return Lower Sash/Window to closed position, check
for Tilt Latch engagement in Jamb Channel by pushing
back and forth and push Lower Sash/W i ndow down
approximately 1” to engage Sash Balances.
• Install replacement Keeper Clips using #5 x 3/4”
Screws, provided. Keeper Clips are placed tight against
route pocket edges and fl ush with top of Check Rail.
Interior View
Interior View
Replace
-
1
-
2
-
3
-
4
