Classic Exhibits VK-2917 Setup Instructions

Typ
Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2917 - General Layout
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
If the locks are set too far forward, the lock will not
fully engage.
Turn the set screw clockwise to move the lock
back into the extrusion, counter-clockwise
to move the lock outward.
The lock should be set back about 1 mm
(1/16”) from the edge of the extrusion for
the locks to engage properly.
When the lock is properly engaged, the
extrusions will fit tightly together.
When the lock is properly engaged, the
extrusion will not move.
Turn the hex wrench clockwise to open the
lock and secure in the groove.
1
2
3If the locks are not properly engaged, gaps
will be noticable and the extrusion will be
loose.
Q914 Lock Information
www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
1
2
3
4
6
9
9
11
8
7
5
Item Qty Description
1 1 96” Q914 Vertical Extrusion
2 1 96” Q914 Vertical Extrusion w/Door Stop
3 1 96” Q914 Vertical Extrusion w/Door Hinges
4 1 96” Q914 Vertical Extrusion
5 1 87” Q914 Horizontal Extrusion
6 1 87” Q914 Horizontal Extrusion
7 1 87” Q914 Horizontal Extrusion
8 1 87” Q914 Horizontal Extrusion
9 2 88.8346” Z45 Horizontal Extrusion
11 1 24” Z45 Horizontal Extrusion
Steps
1) Connect door threshold to bottom of extrusions [2 & 3] as shown in detail.
2) Connect horizontals [5 & 7] between verticals [1 & 2] as shown on page 3.
3) Connect horizontals [6 & 8] between verticals [3 & 4] as shown on page 3.
4) Attach verticals [9] between horizontals [6 & 8] as shown.
5) Attach horizontal [11] between verticals [2 & 3] as shown
6) Attach graphics to Velcro on back of backwall.
Door Threshold
Velcro:
Back/Bottom Edge
Velcro:
Back/Bottom Edge
Velcro:
Back/Top Edge
Velcro:
Back/Top Edge
Door Threshold
Tighten
to secure
Slide into
groove
Door Threshold Attachment
www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Backwall Assembly Cont’d
12
15 15
15
15
15 15
15
15
13 14
16 17
18
Item Qty Description
12 1 96” Z45 Vertical Extrusion
13 1 96” S40 Vertical Extrusion
14 1 96” GS210 Vertical Extrusion
15 8 14” Z45 Horizontal Extrusion
16 1 96” GS210 Vertical Extrusion
17 1 96” S40 Vertical Extrusion
18 1 96” Z45 Vertical Extrusion
Steps
1) Connect
horizontal extrusions [15] between verticals inserting infills as shown.
Infill
Infill Infill Infill
www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Attachments
13
4
9
9
14
16
Steps
1) Connect
vertical extrusion [14] to vertical [1] and vertical [16] to vertical [4] as shown.
2) Attach lights to top of backwall as shown.
3) Attach conference door to hinges on vertical [3] as shown in detail.
4) Attach literature racks to verticals as shown in detail.
5) Attach monitor mount to verticals [9] as shown in detail.
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Door
Hinge
Hinge
Conference Door Attachment
Conference
Door
Attach connector piece to tray
as shown. Then connect
assembled pamphlet
tray to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
*
*
*
*
*
Monitor Mount Attachment
Slide mounting connector
pieces into groove of
extrusion. Tighten setscrew
to secure in place.
Then attach wall plate
to connectors
using supplied bolts.
www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Crate Packing
Level 1 Level 2 Level 3 Level 4 Level 5
Assembled Sides [12,13,15] [15,16,17] Assembled Door Graphics (Case)
Setup Hardware (Box)
Monitor Mount
Lights
Wire Management
Literature Racks
5
1
2315
(x4)
14
12
15 15
13
16 17
Infills
Infills
18
6 7 8 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Classic Exhibits VK-2917 Setup Instructions

Typ
Setup Instructions

w innych językach