H3C S5560S-52P-EI Instrukcja instalacji

H3C S5560S-EI & S5130S-HI Switch Series

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W106-20200509

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this

document are the property of their respective owners.

Notice

The information in this document is subject to change without notice. All contents in this document, including

statements, information, and recommendations, are believed to be accurate, but they are presented without

warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions

contained herein.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

H3C S5560S-EI & S5130S-HI Switch Series Installation Guide describes the appearance,

installation, power-on, maintenance, and troubleshooting of the H3C S5560S-EI and S5130S-HI

Switch Series.

This preface includes the following topics about the documentation:

•

Audience.

•

Conventions.

•

Documentation feedback.

Audience

This documentation is intended for:

•

Network planners.

•

Field technical support and servicing engineers.

•

Network administrators working with the S5560S-EI and S5130S-HI switch series.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention

Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention

Description

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the

New User

window opens; click

OK

.

>

Multi-level menus are separated by angle brackets. For example,

File

>

Create

>

Folder

.

Symbols

Convention

Description

WARNING!

An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION:

An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT:

An alert that calls attention to essential information.

NOTE:

An alert that contains additional or supplementary information.

TIP:

An alert that provides helpful information.

Network topology icons

Convention

Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Represents a wireless terminator unit.

Represents a wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

T

Convention

Description

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

1-1

Contents

1 Preparing for installation ·········································································· 1-3

Safety recommendations ································································································································ 1-4

Examining the installation site ························································································································· 1-4

Temperature and humidity ······················································································································ 1-4

Cleanliness ·············································································································································· 1-5

EMI ·························································································································································· 1-5

Laser safety ············································································································································· 1-5

Installation tools ·············································································································································· 1-6

2 Installing the switch ·················································································· 2-6

Installing the switch in a 19-inch rack·············································································································· 2-7

Installation methods ································································································································ 2-7

Installation accessories ··························································································································· 2-9

Rack-mounting the switch by using front mounting brackets ································································ 2-10

Rack-mounting the switch by using front and rear mounting brackets ·················································· 2-11

Mounting the switch on a workbench ············································································································ 2-14

Grounding the switch ···································································································································· 2-15

Grounding the switch with a grounding strip ························································································· 2-15

Grounding the switch with a grounding conductor buried in the earth ground ······································ 2-17

Installing and removing a power module······································································································· 2-18

Installing a PSR75-12A/PSR150-A1/PSR150-D1 power module ························································· 2-18

Removing a PSR75-12A/PSR150-A1/PSR150-D1 power module ······················································· 2-19

Installing a PSR180-56A/PSR360-56A/PSR560-56D/PSR720-56A/PSR1110-56A power module ····· 2-20

Removing a PSR180-56A/PSR360-56A/PSR560-56D/PSR720-56A/PSR1110-56A power module ··· 2-21

Connecting the power cord ··························································································································· 2-22

Connecting the power cord for a PSR75-12A/PSR150-A1 power module ··········································· 2-23

Connecting the power cord for a PSR150-D1/PSR560-56D power module ········································· 2-24

Connecting the power cord for a PSR180-56A/PSR360-56A/PSR720-56A/PSR1110-56A power module

······························································································································································ 2-25

Installing and removing an expansion module ······························································································ 2-26

Installing an expansion module ············································································································· 2-26

Removing an expansion module ··········································································································· 2-27

Verifying the installation ································································································································ 2-27

3 Accessing the switch for the first time ···················································· 3-28

Setting up the configuration environment ····································································································· 3-28

Connecting the serial console cable ············································································································· 3-28

Connecting the Micro USB console cable ····································································································· 3-29

Setting terminal parameters ·························································································································· 3-31

Powering on the switch ································································································································· 3-31

4 Setting up an IRF fabric ········································································· 4-33

IRF fabric setup flowchart ····························································································································· 4-33

Planning IRF fabric setup ······························································································································ 4-34

Planning IRF fabric size and the installation site ··················································································· 4-34

Identifying the master switch and planning IRF member IDs ································································ 4-34

Planning IRF topology and connections································································································ 4-34

Identifying IRF physical ports on the member switches ········································································ 4-35

Planning the cabling scheme ················································································································ 4-36

Configuring basic IRF settings ······················································································································ 4-40

Connecting the IRF physical ports ················································································································ 4-40

Verifying the IRF fabric setup ························································································································ 4-40

5 Maintenance and troubleshooting ·························································· 5-42

Power module failure ···································································································································· 5-42

Fan tray failure ·············································································································································· 5-42

Configuration terminal display issues············································································································ 5-42

1-2

No display ············································································································································· 5-42

Garbled display ····································································································································· 5-43

6 Appendix A Chassis views and technical specifications ························· 6-44

Chassis views ··············································································································································· 6-44

S5560S-28F-EI ····································································································································· 6-44

S5560S-52F-EI ····································································································································· 6-45

S5560S-28P-EI ····································································································································· 6-46

S5560S-52P-EI ····································································································································· 6-47

S5560S-28S-EI ····································································································································· 6-48

S5560S-52S-EI ····································································································································· 6-49

S5560S-28S-PWR-EI ···························································································································· 6-50

S5560S-52S-PWR-EI ···························································································································· 6-51

S5130S-28C-HI ····································································································································· 6-52

S5130S-28S-HI ····································································································································· 6-53

S5130S-52C-HI ····································································································································· 6-54

S5130S-52S-HI ····································································································································· 6-55

S5130S-28S-PWR-HI ··························································································································· 6-56

S5130S-28S-UPWR-HI ························································································································· 6-57

S5130S-52S-PWR-HI ··························································································································· 6-58

S5130S-28C-PWR-HI ··························································································································· 6-59

S5130S-52C-PWR-HI ··························································································································· 6-60

Technical specifications ································································································································ 6-61

S5560S-EI series ·································································································································· 6-61

S5130S-HI series ·································································································································· 6-66

7 Appendix B FRUs and compatibility matrixes········································· 7-73

Compatibility matrixes ··································································································································· 7-73

Power modules ············································································································································· 7-74

Expansion modules ······································································································································· 7-75

8 Appendix C Ports and LEDs ·································································· 8-76

Ports ······························································································································································ 8-76

Console port ·········································································································································· 8-76

Management Ethernet port ··················································································································· 8-76

USB port ················································································································································ 8-76

10/100/1000BASE-T autosensing Ethernet port ··················································································· 8-77

SFP port ················································································································································ 8-77

SFP+ port ·············································································································································· 8-80

Combo interface ···································································································································· 8-82

LEDs ····························································································································································· 8-82

System status LED ································································································································ 8-82

Power module status LED ····················································································································· 8-82

Mode LED (MODE) ······························································································································· 8-83

10/100/1000BASE-T autosensing Ethernet port LED ··········································································· 8-83

SFP/SFP+ port LED ······························································································································ 8-84

Management Ethernet port LED ··········································································································· 8-84

Input status LED and output status LED on the power module ···························································· 8-84

Expansion slot LED ······························································································································· 8-84

Port status LED on the expansion module ···························································································· 8-85

9 Appendix D Cooling system ··································································· 9-86

1-3

1 Preparing for installation

This document is applicable to the S5560S-EI switch series and the S5130S-HI switch series. Table

1-1 describes models of the S5560S-EI series and the S5130S-HI series.

Table 1-1 Switch models

Series Model Product code

S5560S-EI

S5560S-28F-EI

LS-S5560S-28F-EI

LS-S5560S-28F-EI-GL

S5560S-52F-EI

LS-S5560S-52F-EI

LS-S5560S-52F-EI-GL

S5560S-28P-EI

LS-S5560S-28P-EI

LS-S5560S-28P-EI-GL

S5560S-52P-EI

LS-S5560S-52P-EI

LS-S5560S-52P-EI-GL

S5560S-28S-EI

LS-S5560S-28S-EI

LS-S5560S-28S-EI-GL

S5560S-52S-EI

LS-S5560S-52S-EI

LS-S5560S-52S-EI-GL

S5560S-28S-PWR-EI

LS-S5560S-28S-PWR-EI

LS-S5560S-28S-PWR-EI-GL

S5560S-52S-PWR-EI

LS-S5560S-52S-PWR-EI

LS-S5560S-52S-PWR-EI-GL

S5130S-HI

S5130S-28S-HI

LS-S5130S-28S-HI

LS-S5130S-28S-HI-GL

S5130S-52S-HI

LS-S5130S-52S-HI

LS-S5130S-52S-HI-GL

S5130S-28C-HI

LS-S5130S-28C-HI

LS-S5130S-28C-HI-GL

S5130S-52C-HI

LS-S5130S-52C-HI

LS-S5130S-52C-HI-GL

S5130S-28S-PWR-HI

LS-5130S-28S-PWR-EI

LS-5130S-28S-PWR-EI-GL

S5130S-28S-UPWR-HI LS-5130S-28S-UPWR-HI

S5130S-52S-PWR-HI

LS-5130S-52S-PWR-EI

LS-5130S-52S-PWR-EI-GL

S5130S-28C-PWR-HI

LS-5130S-28C-PWR-EI

LS-5130S-28C-PWR-EI-GL

S5130S-52C-PWR-HI

LS-5130S-52C-PWR-EI

LS-5130S-52C-PWR-EI-GL

1-4

Safety recommendations

To avoid any equipment damage or bodily injury caused by improper use, read the following safety

recommendations before installation. Note that the recommendations do not cover every possible

hazardous condition.

•

Before cleaning the switch, remove all power cords from the switch. Do not clean the switch

with wet cloth or liquid.

•

Do not place the switch near water or in a damp environment. Prevent water or moisture from

entering the switch chassis.

•

Do not place the switch on an unstable case or desk. The switch might be severely damaged in

case of a fall.

•

Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the

switch free of obstruction.

•

Make sure the operating voltage is in the required range.

•

To avoid electrical shocks, do not open the chassis while the switch is operating or when the

switch is just powered off.

•

When installing the switch, wear an ESD wrist strap and make sure it makes good skin contact

and is reliably grounded.

Examining the installation site

The switch must be used indoors. You can mount your switch in a rack or on a workbench, but make

sure:

•

Adequate clearance is reserved at the air inlet and outlet vents for ventilation.

•

The rack or workbench has a good ventilation system.

•

Identify the hot aisle and cold aisle at the installation site, and make sure ambient air flows into

the switch from the cold aisle and exhausts to the hot aisle.

•

Identify the airflow designs of neighboring devices, and prevent hot air flowing out of the

neighboring device from entering the device.

•

The rack is sturdy enough to support the switch and its accessories.

•

The rack or workbench is reliably grounded.

To ensure correct operation and long service life of your switch, install it in an environment that meets

the requirements described in the following subsections.

Temperature and humidity

Maintain temperature and humidity in the equipment room as described in "Appendix A Chassis

views and technical specifications."

•

Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

•

Lasting low relative humidity can cause washer contraction and ESD and cause problems

including loose mounting screws and circuit failure.

•

High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the switch.

For the temperature and humidity requirements of different switch models, see "Technical

specifications."

1-5

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points, especially when indoor relative humidity is low. In the worst

case, electrostatic adsorption can cause communication failure.

Table 1-2 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m³)

Dust

≤ 3 x 10

4

(no visible dust on the tabletop over three days)

NOTE:

Dust diameter ≥ 5 μm

The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion

and premature aging of components, as shown in Table 1-3.

Table 1-3 Harmful gas limits in the equipment room

Gas Maximum concentration (mg/m

3

)

SO

2

0.2

H

2

S 0.006

NH

3

0.05

Cl

2

0.01

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the switch and application

system, adversely affect the switch in the following ways:

•

A conduction pattern of capacitance coupling.

•

Inductance coupling.

•

Electromagnetic wave radiation.

•

Common impedance (including the grounding system) coupling.

To prevent EMI, use the following guidelines:

•

If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

•

Keep the switch far away from radio transmitting stations, radar stations, and high-frequency

devices.

•

Use electromagnetic shielding, for example, shielded interface cables, when necessary.

•

To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning

strikes, route interface cables only indoors.

Laser safety

WARNING!

Disc

onnected optical fibers or transceiver modules might emit invisible laser light. Do not stare into

beams or view directly with optical instruments when the switch is operating.

2-6

The switch is a Class 1 laser device.

Installation tools

No installation tools are provided with the switch. Prepare installation tools yourself as required.

•

ESD wrist strap

•

Flat-blade screwdriver

•

Phillips screwdriver

•

Needle-nose pliers

•

Diagonal pliers

•

Crimping tool

•

Marker

2 Installing the switch

CAUTION:

Keep the tamper

-

proof seal on a mounting screw on the chassis cover intact, and if you want to open

the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence.

2-7

Figure 2-1 Hardware installation flow

Installing the switch in a 19-inch rack

Installation methods

Table 2-1 Installation methods for the S5560S-EI and the S5130S-HI switches

Chassis

Installation

methods

Installation requirements

Installation

procedure

S5560S-28F-EI

S5560S-52F-EI

S5560S-28P-EI

S5560S-52P-EI

Using front

mounting

brackets

Install the front mounting brackets at the

port side or the power module side.

See

"Rack-mounting the

switch by using front

mounting brackets."

Start

Install the switch

Ground the switch

Connect power cords

Verify the installation

Turn on the circuit breakers

Operating correctly?

Turn off the circuit

breakers

Troubleshoot the

switch

No

End

Connect interface connectors and

cables

Select and install power modules

Yes

Expansion module required?

Install the expansion module

Operating correclty?

Troubleshoot the

switch

Yes

No

2-8

Chassis

Installation

methods

Installation requirements

Installation

procedure

S5560S-28S-EI

S5560S-52S-EI

S5130S-28S-HI

S5130S-52S-HI

S5130S-28C-HI

S5130S-52C-HI

S5560S-28S-PWR-

EI

S5560S-52S-PWR-

EI

S5130S-28S-PWR-

HI

S5130S-28S-UPW

R-HI

S5130S-52S-PWR-

HI

S5130S-28C-PWR-

HI

S5130S-52C-PWR-

HI

Using front and

rear mounting

brackets

• Install the front mounting brackets at

the port side or power module side.

• Install the rear mounting brackets

according to the rack depth.

 If the rack depth is in the range of

429 to 595 mm (16.89 to 23.43 in),

orient the bracket with the wide

flange inside the rack.

 If the rack depth is in the range of

274 to 440 mm (10.79 to 17.32 in)

and the distance from the rear rack

posts to the inner surface of the

cabinet door is longer than 153 mm

(6.02 in), orient the bracket with the

wide flange outside the rack.

• To use PSR1110-56A power modules,

do not install the switch in a rack with a

depth of 600 mm (23.62 in)

See

"Rack-mounting the

switch by using front

and rear mounting

brackets."

Figure 2-2 Procedure for rack-mounting the switch by using the front mounting brackets

Figure 2-3 Procedure for rack-mounting the switch by using the front and rear mounting

brackets

NOTE:

If a rack shelf is available, you can put the switch on the rack shelf, slide the switch to an appropriate

location, and attach the switch to the rack by using the mounting brackets.

Attach the front

mounting brackets to the

two sides of the switch

Identify the mounting position (port

side or power side) for the

mounting brackets

Mount the switch in the rack

Attach the front

mounting

brackets to the

two sides of the

switch

Attach the load

bearing screws to

the switch

Attach the

rear

mounting

brackets to

rack posts

Identify the mounting

position (port side or

power side) for the

mounting brackets

Mount the switch in

the rack

2-9

Installation accessories

Table 2-2 Installation accessories for the S5560S-EI and the S5130S-HI switches

Installation accessories

S5560S-28F-EI

S5560S-52F-EI

S5560S-28P-EI

S5560S-52P-EI

S5560S-28S-EI

S5560S-52S-EI

S5130S-28S-HI

S5130S-52S-HI

S5130S-28C-HI

S5130S-52C-HI

S5560S-28S-PWR-EI

S5560S-52S-PWR-EI

S5130S-28S-PWR-HI

S5130S-28S-UPWR-HI

S5130S-52S-PWR-HI

S5130S-28C-PWR-HI

S5130S-52C-PWR-HI

Front mounting brackets (Figure 2-4) Provided Provided

Rear mounting brackets and shoulder screws (Figure

2-5)

N/A Provided

Figure 2-4 Front mounting bracket

(1) Screw hole for attaching the bracket to the switch

(2) Screw hole for attaching the bracket to the rack

Figure 2-5 Rear mounting bracket and shoulder screw

(1) Screw hole for attaching the bracket to the rack

(2) Shoulder screw

1

2

1

2

2-10

Rack-mounting the switch by using front mounting brackets

Attaching the front mounting brackets to the switch

1. Determine the mounting position for the front mounting brackets. You can install the front

mounting brackets at the port side or the power module side.

2. Attach the front mounting brackets to the chassis:

a. Align the round holes in the wide flange of one front mounting bracket with the screw holes

in the chassis. See Figure 2-6 and Figure 2-7.

b. Use M4 screws (provided with the switch) to attach the front mounting bracket to the

chassis.

c. Repeat the proceeding two steps to attach the other front mounting bracket to the chassis.

Figure 2-6 Attaching the front mounting bracket to the port side

Figure 2-7 Attaching the front mounting bracket to the power module side

Mounting the switch in the rack

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Make sure the front mounting brackets have been attached securely to the two sides of the

switch.

3. One person supports the chassis bottom with one hand, holds the front part of the chassis with

the other hand, and pushes the chassis into the rack.

4. The other person uses M6 screws and cage nuts (user supplied) to attach the switch to the rack.

Make sure the switch is installed evenly and securely in the rack.

2-11

Figure 2-8 Mounting the switch in the rack (front mounting brackets at the port side)

Figure 2-9 Mounting the switch in the rack (front mounting brackets at the power

module side)

Rack-mounting the switch by using front and rear mounting

brackets

Attaching the front mounting brackets and shoulder screws to the switch

You can attach the front mounting brackets at the port-side or power module-side mounting position.

The following uses port-side mounting as an example. The power-side mounting is similar.

To attach the front mounting brackets and shoulder screws to the switch:

1. Align the round holes in the wide flange of one front mounting bracket with the screw holes in

the port-side mounting position on one side of the chassis. See Figure 2-10.

2-12

2. Use M4 screws (supplied with the switch) to attach the front mounting bracket to the chassis.

3. Repeat the proceeding two steps to attach the other front mounting bracket to the chassis.

4. Unpack the shoulder screws. Attach a shoulder screw to one of the two installation positions as

red-marked in Figure 2-10 at both sides of the chassis.

Figure 2-10 Attaching the front mounting brackets and shoulder screws to the chassis

Attaching the rear mounting brackets to the rack

1. Determine the switch installation position in the rack.

2. Install cage nuts in the rack posts.

3. Orient the rear mounting brackets with the wide flange inside or outside the rack as required.

4. Use M6 screws to attach the rear mounting brackets to the rear posts, as shown in Figure 2-11.

Do not fully tighten the M6 screws before mounting the switch in the rack.

Figure 2-11 Attaching the rear mounting brackets to a rack with the wide flange inside the

rack

2-13

Figure 2-12 Attaching the rear mounting brackets to a rack with the wide flange outside the

rack

Mounting the switch in the rack

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Make sure the front mounting brackets and shoulder screws are securely attached to the two

sides of the switch.

3. Attach cage nuts to the rack posts.

4. One person supports the chassis bottom with one hand, holds the front part of the chassis with

the other hand, and pushes the chassis into the rack gently.

Make sure the shoulder screws make close contact with the upper edges of the rear mounting

brackets, as shown in Figure 2-13.

5. The other person aligns the oval holes in the front brackets with the mounting holes in the front

rack posts, and attaches the front mounting brackets with M6 screws to the front rack posts.

Make sure the switch is installed securely in the rack.

2-14

Figure 2-13 Mounting the switch in the rack (with the wide flange of the rear mounting

brackets inside the rack)

Figure 2-14 Mounting the switch in the rack (with the wide flange of the rear mounting

brackets outside the rack)

Mounting the switch on a workbench

IMPORTANT:

•

Reserve a minimum of 10 cm (3.9 in) of clearance around the chassis for heat dissipation.

• Do not place heavy objects on the switch.

2-15

To mount the switch on a workbench:

1. Verify that the workbench is sturdy and reliably grounded.

2. Place the switch with bottom up, and clean the round holes in the chassis bottom with dry cloth.

3. Attach the rubber feet to the four round holes in the chassis bottom.

4. Place the switch with upside up on the workbench.

Grounding the switch

WARNING

!

•

Correctly connecting the grounding cable is crucial to lightning protection and EMI protection.

•

As a best practice to guarantee the grounding effect, ground the switch by connecting the

grounding cable provided with the switch to the grounding strip in the equipment room.

The power input end of the switch has a noise filter, whose central ground is directly connected to the

chassis to form the chassis ground (commonly known as PGND). You must securely connect this

chassis ground to the earth to minimize the potential for system damage, maximize the safety at the

site, and minimize EMI susceptibility of the system.

You can ground the switch in one of the following ways, depending on the grounding conditions

available at the installation site:

•

Grounding the switch with a grounding strip

•

Grounding the switch with a grounding conductor buried in the earth ground

NOTE:

•

The power and grounding terminals in this section are for illustration only.

• For more information about lightning protection, see H3C Lightning Protection Guide.

Grounding the switch with a grounding strip

WARNING

!

Connect the grounding cable to the grounding

strip

in the equipment room. Do not connect it to a fire

main or lightning rod.

If a grounding strip is available at the installation site, connect the grounding cable to the grounding

strip.

Connecting the grounding cable to the chassis

1. Remove the grounding screw from the rear panel of the switch chassis.

2. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding

screw hole. Fasten the screw.

Strona się ładuje...

H3C S5560S-52P-EI Instrukcja instalacji

H3C S5560S-52P-EI Instrukcja instalacji

w innych językach

Powiązane artykuły

Inne dokumenty