SignaMax I-200 10G SFP+ to Multigigabit PoE++ Industrial Media Converter Skrócona instrukcja obsługi

Marka
SignaMax
Model
I-200 10G SFP+ to Multigigabit PoE++ Industrial Media Converter
Typ
Skrócona instrukcja obsługi
Quick Start Guide
www.signamax.com
QSG-SI20010_A-3-23
www.signamax.com
999 N.W. 159th Drive
Miami, FL 33169
Tel: 800.446.2377
COPYRIGHT 2007 SIGNAMAX, INC. ■ ALL RIGHTS RESERVED ■ SPECIFICATIONS SUBJECT TO CHANGE
CONNECT WITH US
I-200 Series Industrial 10G PoE++
Media Converter
Part
Number
RJ-45
Ports
PoE
Ports
SFP
Ports
MI20010 11 1
Unpack the Device and Check Contents
DIN-Rail Mounting Kit - one bracket
and two screws.
Wall Mounting Kit - two brackets and
four screws
Documentation—Quick Start Guide
(this document) and Warranty Card
Note: Additional documentation can be obtained from
www.signamax.com
Warning: This product does not contain any serviceable user
parts.
Warning: Installation and removal of the unit must be carried out
by qualied personnel only.
Warning: When connecting this device to a power outlet, connect
the eld ground lead on the tri-pole power plug to a valid earth
ground line to prevent electrical hazards.
Warning: This switch uses lasers to transmit signals over ber
optic cable. The lasers are compliant with the requirements of
a Class 1 Laser Product and are inherently eye safe in normal
operation. However, you should never look directly at a transmit
port when it is powered on.
Warning: When selecting a ber SFP device, considering safety,
please make sure that it can function at a temperature that is not
less than the recommended maximum operational temperature of
the product. You must also use an approved Laser Class 1 SFP
transceiver.
Caution: Wear an anti-static wrist strap or take other suitable
measures to prevent electrostatic discharge when handling this
equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port.
This may damage this device.
Caution: Use only twisted-pair cables with RJ-45 connectors that
conform to FCC standards.
!
!
Mount the Media Converter
DIN-Rail Mount
1. Screw the DIN-Rail bracket to the Media Converter
2. Insert the top of the DIN-Rail bracket to the DIN-Rail track.
3. Pull down the DIN-Rail bracket to the DIN-Rail track and check if it is
mounted tightly on the DIN-Rail track.
Warnings and Cautionary Messages
Wall Mount
1. Remove the four mounting screws on the rear panel
2. Turn around the 2 brackets and reinsert the the four mounting screws
Hangers for Installation
Rear Panel
Tighten the screws (screw standard:M3*4)
Rear Panel
www.signamax.com
999 N.W. 159th Drive
Miami, FL 33169
Tel: 800.446.2377 CONNECT WITH US
QSG-SI20010_A-3-23
COPYRIGHT 2007 SIGNAMAX, INC. ■ ALL RIGHTS RESERVED ■ SPECIFICATIONS SUBJECT TO CHANGE
Quick Start Guide
I-200 Series Industrial 10G PoE++ Media Converter
1. Insert the positive and negative wires into the PWR1 (+,-) and/or PWR2
(+,-) on the terminal block connector (only one power supply is required).
2. Tighten the screws to prevent the wires from loosening.
3. Only one power supply is required for operation of the switch. Dual
power sources are for redundancy. The Fault LED will light on if only
one power supply is connected.
4. The Medi Converter supports 802.3bt Type 4 with maximum power con-
sumption of 95W. Make sure the power supply is able to provide su-
cient power for the PoE requirement.
1. For RJ-45 ports, connect 100-ohm Category 5, 5e or better twisted-pair
cable. Cat6A is required for 10GBase-T up to 100m while Cat5e or
Cat6 may reach up to 55m. Cat6 or better is required for 5GBase-T and
Cat5e for 2.5GBase-T.
2. For the SFP slots, rst install SFP transceivers and then connect -
ber optic cabling to the transceiver ports. The following transceivers are
supported:
10GBASE-SR (AS510020)
10GBASE-LR (AS510030)
10GBASET (AS50010)
3. As connections are made, check the port status LEDs to be sure the
links are valid. See the LED description table below.
Connect Power
Connect Network Cables
LED Description Table
1. This equipment must be grounded. Never defeat the ground conductor
or operate the equipment in the absence of a suitably installed ground
conductor. Contact the appropriate electrical inspection authority or an
electrician if you are uncertain that suitable grounding is available.
2. Attach a lug (not provided) to a #12 AWG minimum grounding wire (not
provided), and connect it to the grounding point on the rear panel. Then
connect the other end of the wire to ground.
Caution: The earth connection must not be removed unless all
supply connections have been disconnected.
Note: The device must be installed in a restricted access loca-
tion. It should have a separate protective earthing terminal on
the chassis that must be permanently connected to earth to ad-
equately ground the chassis and protect the operator from elec-
trical hazards.
!
Ground the Media Converter
LED Status Description
P1 ON DC Power is connected to PWR1
OFF No DC power is connected to PWR1
P2 ON DC Power is connected to PWR2
OFF No DC power is connected to PWR2
Fault ON Only 1 power supply is connected
OFF Both PWR1 and PWR2 are connected
LINK
ON Port has a valid link
BLINKING Port has network activity
OFF The link is down
PoE ON A PoE device is connected and delivered PoE power
OFF Doesn’t deliver PoE power
PWR 1 PWR 2
1. Verify basic Media Converter operation by checking the system LEDs.
When operating normally, the Power LED should be on and green.
Verify Media Converer Operations
  • Page 1 1
  • Page 2 2

SignaMax I-200 10G SFP+ to Multigigabit PoE++ Industrial Media Converter Skrócona instrukcja obsługi

Marka
SignaMax
Model
I-200 10G SFP+ to Multigigabit PoE++ Industrial Media Converter
Typ
Skrócona instrukcja obsługi
ściągnij PDF
raport

w innych językach

Inne dokumenty