Terma grzałki TDY Instrukcja obsługi

PLEN DE IT RU

User Manual

Electric Heang ElementElectric Heang Element

Gebrauchsanweisung — Elektroheizpatrone Gebrauchsanweisung — Elektroheizpatrone || Manuale d'istruzioni — Elemento Manuale d'istruzioni — Elemento

elerico riscaldante elerico riscaldante || Instrukcja Obsługi — Grzałka elektryczna Instrukcja Obsługi — Grzałka elektryczna || Инструкция по Инструкция по

применению — Электронагревательприменению — Электронагреватель

TDY

3

EN

User Manual

Our products have been designed and manufactured in

such a way to ensure that all quality, funconality and aes-

thec requirements are met. We would like to congratu-

late you on the purchase of this great product and wish

you a pleasant experience with it.

Electric radiator

Guide to safe installaon

and use.

1. Do not install the heater under an electrical socket

point.

2. Your electric heater should be lled with a carefully

measured amount of liquid. In the case of loss of heat-

ing medium, or in any other case which demands its

supplementaon, contact your supplier.

4User manual TDY www.termaheat.pl

3. The device is not equipped with an external tempera-

ture controller *).

Do not use the device in a small room if unsupervised

disabled or incapacitated individuals are inside it. Only

use the device if those individuals are under constant

supervision.

*) Does not apply to selected models. Ask your supplier for details.

4. Electric heater is not a toy. Children under the age

of 3 should not be allowed within close proximity

of the device without the supervision of an adult.

Children aged 3 to 8 should only be allowed to oper-

ate the heater when it has been properly installed and

connected. The child must be under adult supervi-

sion or have been trained to safely operate the device

while understanding the risks.

5. Note: Some parts of the radiator can be very hot and

can cause burns. Pay special aenon to the presence

of children or people with disabilies.

5

EN

6. If the device is used as a clothes and towel dryer, ensure

that the fabrics drying on it have only been washed in

water, avoiding contact with any harsh chemicals.

7. To ensure the safety of very small children, install

the electric dryer so that the lowest tube is at least

600 mm above the oor.

8. The device should only be installed by a qualied in-

staller in accordance with the applicable regulaons

regarding safety and all other regulaons.

9. All installaons to which the device is connected

should comply with regulaons applicable in the coun-

try of installaon and use.

10. Extension leads or electric plug adapters should not

be used in order to supply power to the heater.

11. While connecng the radiator to electric installaon

ensure that the curcuit has a 30 mA residual-cur-

rent circuit breaker and an appropriate overcurrent

circuit breaker. With the permanent installaon (ca-

ble connecon without plug) it is also mandatory

to provide an omnipolar cut-o switch with a min-

imum contact opening of 3 mm for disconnecng

the device on all poles.

6User manual TDY www.termaheat.pl

12. The device version labelled PB can be installed in bath-

rooms in zone 1, as dened by applicable law, subject

to any addional regulaons concerning electrical in-

stallaons in wet areas.

Other versions of the device can be installed in Zone 2

or beyond.

13. The device is recommended for use solely as de-

scribed in the manual.

14. Ensure that the heater has been installed on a wall in

accordance with its installaon manual.

15. Please forward this instrucon manual to the end

user.

7

EN

Zone 1

Zone 2

8User manual TDY www.termaheat.pl

Electric Heang

Element

Safety requirements

— installaon

1. Fing and connecon of the heang element should

only be performed by a qualied installer.

2. Connect the unit to a sound electrical installaon (see

the rangs on the heater).

3. Switching on the heang element in the open air to test

the device is permied for a maximum of 3 seconds.

4. Never test a heang element that is already installed.

Do not turn the heang element on in an empty

radiator!

5. Ensure that the power cord does not touch the hot

parts of the heang element or radiator.

9

EN

6. Before installing or removing the device, make sure it

is disconnected from the power source.

7. Do not open the device — any interference with inter-

nal components will invalidate the warranty.

8. The heang element’s power output must not ex-

ceed the radiators power output for the parameters

75/65/20° C.

9. The pressure in the radiator should not exceed 10 atm.

Ensure that an air cushion is preserved in electric radi-

ators. In central heang systems, leave one valve open

to prevent pressure build up due to the thermal ex-

pansion of the liquid.

10. The device is intended for home use only.

11. Fing and Installaon of the device must be carried

out in accordance with all local regulaons for elec-

trical safety, including installaon within permissi-

ble locaons only. Observe bathroom electrical zone

regulaons.

10 User manual TDY www.termaheat.pl

Safety requirements — use

1. The heang element must be fully submerged in the

heang liquid during its operaon.

2. Regularly check the device for damage to ensure it is

safe to use.

3. If the power cord is damaged the device should not be

used. Unplug the device and contact the manufactur-

er or distributor.

4. Do not allow ooding into the heang element casing.

5. Do not use the heang element in heang systems

where the water temperature exceeds 82° C.

6. The heang element and radiator can heat up to high

temperatures. Please be cauous — avoid direct con-

tact with the hot parts of the equipment.

7. Do not open the heang element casing.

8. In the central heang system, always make sure that

one valve of the radiator remains open.

11

EN

9. Ensure that minors aged 8 and above or those with

a physical or mental disability are supervised if operat-

ing the device.

10. The device is not a toy. Keep it out of the reach of

children.

11. The device must be disconnected from the mains dur-

ing cleaning and maintenance.

12. Cleaning of the equipment by children under 8 years of

age is only permied under appropriate supervision.

12 User manual TDY www.termaheat.pl

Intended use of device

The heating element is an electric device

intended solely for installaon in radiators

(standalone or connected to the central

heang system)

Heating element power output should

be matched with radiator output for pa-

rameters of 75/65/20° C

Technical informaon

Model markings

(power cable type):

PB (Straight cable without plug) *

PW (Straight cable with plug)

SW (Spiral cable with plug)

Type of electrical connecon: Y

Heat outputs available: 120, 200, 300, 400, 600, 800, 1000, 1200 [W]

Power supply: 230 V / 50 Hz

Insulaon class: Class I

Towel rail connecon thread: G 1/2"

Casing protecon class [IP]: IPx5

Length of heang element: 120 200 300 400 600 800 1000 1200 [W]

315 275 300 335 365 475 565 660 [mm]

* Device intended to be connected permanently to the system

13

EN

Installaon or removal

Detailed informaon demonstrang the dif-

ferent ways of installing or removing a radi-

ator heang element is available from the

manufacturer or importer (see footnotes at

the end of the manual). Below we list some

basic requirements and principles which

must be followed to ensure long term, relia-

ble operaon of the product.

150°

When the heang element is installed hor-

izontally, it must be rotated to such an ex-

tent that the single tube, which houses the

temperature sensor, is posioned as low as

possible.

Before installaon or rst use:

1. Read the chapter Safety requirements

—Installaon.

2. Fit the heang element using the cor-

rect spanner (size 22).

3. The heang element must be installed

at the boom of the radiator, perpen-

dicular to the radiator pipes, while pre-

serving space for the proper circulaon

of the heang medium.

4. Use a suitable heang medium for ll-

ing the electric radiator, i.e. (water, spe-

cial products based on water and glycol

for use in central heang systems, or oil

which complies with the requirements

of the manufacturer of the radiator and

heang element).

8% (20°C)

14 User manual TDY www.termaheat.pl

5. Check the distances between the indi-

vidual heang element tubes and bend

if necessary.

5 mm

2-3 mm

6. Do not switch the heang element on if

it is not fully immersed in radiator heat-

ing medium.

7. Make sure an adequate air cushion is pre-

sent to protect against excessive pressure

build up within the heater (always leave

one of the radiator valves open).

8. When lling the radiator with hot liquid

insure that the liquid temperature does

not exceed 65° C.

9. Follow the subsequent guidelines when

connecng the electrical installaon:

a. Brown wire — live connecon to the

circuit (L).

b. Blue wire — connect to neutral (N)

c. Yellow & green wire — earth con-

necon (PE).

10. Before filling the radiator with heating

medium, ensure that the heang element

is ed properly and that it is water ght.

11. In central heating installation radiator

must be ed with the valves enabling

disconnecon of the radiator from the

rest of the system.

12. The temperature of the heang agent

in the central heang system must not

exceed 82° C!

13. For detailed installation hints — see

the last pages of this manual.

Notes prior to removal:

1. Before dismantling permanently, discon-

nect the heang element from the mains

and ensure that the radiator is not hot.

2. Be aware. A radiator filled with liquid

can be very heavy. When moving the

radiator, ensure that you take the nec-

essary safety precauons.

3. Before disassembly, close the appropri-

ate valves and drain the radiator com-

pletely to avoid causing any damage.

15

EN

Product disposal

This product should not be disposed of as

general waste but should be brought to the

appropriate collecon point for re- cycling of

electric and electronic devices. This informa-

on is provided by the sign on the product,

user manual and packaging. Informaon on

the appropriate point for used devices can be

provided by your local authority, product dis-

tributor or the store from where the product

was purchased. Thank you for your eort to-

wards protecng the environment.

Maintenance

• Before performing maintenance, always

unplug the unit from the mains system.

• Periodically check the uid level in the ra-

diator and ensure the heang element is

completely submerged.

• Clean the product with a dry or damp

cloth. If necessary, use a very small

amount of detergent, ensuring that it

contains no solvents or abrasives.

16 User manual TDY www.termaheat.pl

TDY

The TDY heang element has 3 temperature

sengs and an automac turn-o switch.

The LED indicator shows, aer each seng

change, the currently set temperature lev-

el as well as me remaining unl the end of

a heang cycle. Each seng change is also

conrmed by a corresponding beep.

The built-in temperature sensor prevents

the radiator from freezing when tempera-

ture falls below 5-7°C.

How to operate TDY

To switch on the heang element, press the

buon. The red LED light, indicates that the

heang element is on and operang. The cor-

responding double beep conrms that the

device has been either switched on or o.

countdown mer display

Red LED indicator

on/o buon

Every me the device is switched on, the

countdown mer is reacvated — 5 blue

LEDs light up. The factory default mer set-

ng is 120 minutes (it is possible to change

the countdown mer range between 60-180

min in the advanced sengs mode).

How to read the countdown mer

The number of lit up, blue LEDs tells you how

much me is le unl the end of the heang

cycle: the me of one LED is equal to 2/10

(20%) of the total countdown me, this is ad-

dionally divided into 2 equal parts when the

LED glows connuously or ashes. This way

temperature seng

countdown mer display

Red LED indicator

on/o buon

17

EN

you can easily read the remaining me le

to the end of the heang cycle to 1/10 (10%)

accuracy. Depending on the preset total op-

erang me (60-90-120-150-180 minutes),

the shortest me indicated by your device

will be 6-18 minutes.

Each LED, rst glows connuously for 1/10

of the set me, and for another 1/10 of the

set me, it ashes and then goes out. The

red LED glows constantly throughout the op-

eraon me unl the unit switches itself o.

Example for default factory seng

(working me = 120 min)

— immediately aer switching the device

on, all blue LEDs light up,

— aer 12 minutes the last LED starts ash-

ing and aer further 12 minutes the LED

goes out.

— Each LED rst glows connuously for 12

minutes, then ashes for further 12 min-

utes and goes out and so on unl the full

heang cycle me is up and the device

turns itself o.

How to set the operang

temperature

To set the operang temperature of the heat-

ing element:

— briey press buon — the rst press

puts the heating element into setting

mode — the red LED goes out and a sin-

gle blue LED ashes, indicang the cur-

rent temperature seng,

— another press on the buon will change

the temperature — the corresponding

blue LED ashes and a single beep is emit-

ted (characterisc high pitch sound indi-

cates 40°C seng, the remaining two

temperature sengs are indicated by

low pitch sound).

Temperature seng

Display of operang temperature 40°C 50°C 60°C

Each me the temperature seng is changed,

a single, corresponding LED ashes for 3 sec-

onds. Aer the 3 seconds the heang ele-

ment returns to operaon with the new set-

ngs applied- the red LED lights up and the

LED display shows the countdown mer.

Please note: During operaon, it is possible

to change the temperature any number of

mes, seng the new temperature does not

aect the countdown mer. It is possible to

manually turn o the device at any me.

18 User manual TDY www.termaheat.pl

Advanced sengs

How to change the length of countdown me.

— when the heang element is on, press

and hold buon for 5 seconds - ash-

ing red light and a single beep indicate

that the element goes into seng mode,

— use the buon to select the desired

length of countdown me — a single beep

conrms the change of seng (charac-

terisc high pitch sound indicates the

shortest countdown me seng = 60

minutes).

Seng the

countdown me

9060 120 150 180 min

— Aer a short me, the heang element

automacally returns to operaon with

the new sengs applied — the red LED

lights up and the LED display shows the

countdown mer.

How to enable/disable sound

nocaons

When the heang element is o, press and

hold buon for 5 seconds — special triple

beep conrms the change of sengs:

— sound nocaon is enabled and con-

firmed by the following sequence of

sounds: low-low-high.

— sound nocaon is disabled and con-

firmed by the following sequence of

sounds: high-high-low.

Troubleshoong

Please note: The control system of the heat-

ing element acvates it only when the radi-

ator temperature is lower than the set tem-

perature. When the required temperature

is reached, the heang element will then

switch itself on and o automacally, only to

maintain the set temperature. Consequently,

the electricity consumpon is signicantly

lower than the theorecal calculaon based

on the nominal power of the heang element.

The design as well as the physical character-

iscs of various heang media may cause

uneven temperature distribuon inside the

radiator, including the case where the lower

radiator tubes may be cold. Such occurrence

is completely normal and does not indicate

fault of the heang element.

19

EN

Problem Possible cause Problem soluon

Heang element is con-

nected to the mains but

no LEDs lights up.

Mains

connecon.

Check the cable for damages and if the

device is properly plugged in. Check the

plug and the socket.

Heang element does

not heat up. LEDs light

up alternately and

evenly

Overheang

Make sure the power output of the heat-

ing element does not exceed the rec-

ommended heang output of a radiator.

Check and reduce the temperature of the

heang medium inside the central heang

installaon (it cannot be higher than 82°C)

If the radiator is not connected to the cen-

tral heang installaon, make sure it has

been properly lled with heang medium.

Heang element does

not heat up. LEDs light

up alternately and

unevenly

Damage to the

temperature

sensor

Disconnect the device from the power

supply, wait unl it cools down, connect

the device back to the power supply.

If the problem persists, contact your supplier.

20 User manual TDY www.termaheat.pl

Warranty terms & condions

1. The subject of this warranty is a Terma

electric heating element with control

head. The product name and character-

iscs are specied on the packaging.

2. By accepting the device on purchase,

the Client conrms that the product is

of full value. The Client should imme-

diately inform the Seller of any discov-

ered faults — otherwise it will be un-

derstood that the Product was faultless

at the me of purchase. This refers es-

pecially to any faults or damages of the

control panel case.

3. The Warranty for period for the Product

is 24 months from the date of purchase,

but no longer than 36 months from the

date of producon.

4. Any claims made will be processed on

production of the warranty card and

the evidence of purchase. The manu-

facturer has the right to reject any claim

on the grounds of failure to present any

of the above documents.

5. This warranty does not cover any faults

that are due to:

— incorrect (not in accordance with

the manual) installation, use or

disassembly,

— incorrect use of the heating ele-

ment (i.e. for any purpose that is not

specied by the Manufacturer as in-

tended for this type of product),

— Product being handled by unauthor-

ized persons,

— Fault’s or damages caused by the

Client after having purchased and

accepted the Product.

6. The Central Heang installaon should

be fitted with lock-shield valves, ena-

bling disassembly of the radiator or the

heating element and its control head

without the necessity of emptying the

whole system of the heang agent. Any

problems or expenses arising from the

absence of lock-shield valves in your in-

stallaon cannot be used as grounds for

any claims against Terma.

7. The aached Product Manual is an in-

tegral element of the Warranty. Please

read it carefully prior to the installaon

and use of the Product.

8. The Manufacturer is obliged to remove

any producon fault within 14 working

days of receipt of the faulty device at

the Manufacturer’s premises.

9. Should the repair be impossible, then

the manufacturer is obliged to replace

the faulty Product with a new, full-value

unit of idencal parameters.

Strona jest ładowana ...

Terma grzałki TDY Instrukcja obsługi

Terma grzałki TDY Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty