Pulsar SFG64F1 Instrukcja obsługi

1

SFG64F1

v1.0

SFG64F1 port switch for 4 IP cameras

PL

Edition: 1 from 17.01.2020

Supercedes the edition: -----------

EN

Features:

 6 ports switch

4 PoE ports 10/100/1000Mb/s (data transfer and power

supply)

1 port 10/100/1000Mb/s (UP LINK, TP)

1 port 10/100/1000Mb/s (UP LINK, SFP)

 30 W for each PoE port, supports devices complaint

with the IEEE802.3af/at (PoE+) standard

 Supports auto-learning and auto-aging of MAC

addresses (2K size)

 Built-in switch mode power supply

PSD520115 52 V DC/1,15 A/60 W

 Additional mounting elements

 LED indication

 warranty – 2 year from the production date

Example of use.

1. Technical description

1.1. General description.

SFG64F1 is a 6-ports PoE switch designed to supply IP cameras operating in IEEE 802.3af/at standard. Automatic

detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 – 4 ports of the switch. The UP LINK (5 and

SFP) ports is used for connection of another network device via of fiber optic (shall be used GBIC SFP port). The LEDs at the

front panel indicate the operation status (description in the table below).

The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a

separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access

point or router.

2

1.2 Block diagram.

Fig. 1. Block diagram.

1.3. Description of components and connectors.

Table 1. (see Fig.2)

Element no.

(Fig. 2)

Description

[1]

1 x UP LINK port (SFP)

[2]

1 x UP LINK port (TP)

[3]

4 x PoE ports (1÷4)

[4]

DC power supply socket

[5]

Additional mounting elements

Fig. 2. The enclosure view.

3

1.4. Technical parameters.

Table 2.

Ports

6 10/100/1000Mb/s ports (4 x PoE + 2 x UpLink)

with connection speed auto-negotiation and MDI/MDIX Auto Cross

PoE power supply

IEEE 802.3af/at (1÷4 ports), 52 V DC / 30 W at each port *

Protocols, Standards

IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP

Bandwidth

12Gbps

Transmission method

Store-and-Forward

Optical indication of operation

Switch power supply;

Link/Act;

PoE Status

Power supply

~100-240 V; 50/60 Hz; 1,3 A

switched mode power supply PSD520115 52 V DC / 1,15 A/60 W max.

Operating conditions

temperature -10°C ÷ 40°C,

relative humidity 5 % - 90 %, no condensation

Dimensions

W=118, H=28, D=95 [+/- 2mm]

Additional equipment

surface mounting sheets

Net/gross weight

0,6 / 0,8kg

Protection class

EN 60950-1:2007

II (second)

Storage temperatur

-20 ºC÷60 ºC

Declarations

CE

* The given value of 30 W per port is the maximum value. The total power consumption should not exceed 48 W.

2. Installation

2.1. Requirements

The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative

humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C. Ensure the free flow of air around

the unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the

enclosure.

The load balance should be done before installation Switcha. The given value of 30 W per port is the maximum value

referring to a single output. The total power consumption should not exceed 48 W when all PoE ports are being used. The

increased demand for power is particularly evident in the case of cameras with heaters or infrared illuminators - when launching

these features, the power consumption increases rapidly, which may adversely affect the operation of the switch. The device is

designed for a continuous operation and is not equipped with a power-switch. Therefore, an appropriate overload protection in

the power supply circuit should be provided. The electrical system shall be made in accordance with applicable standards and

regulations.

2.2. Installation procedure

1. Connect switch to the PSD520115 52 V DC power supply unit desktop type.

2. Connect the power supply to the 230 V socket.

3. Connect the camera wires to the RJ45 connectors (PoE connectors).

4. Check the optical indication of the switch operation (see Table 3).

4

Connection schemes.

5

3. Operation indication.

Table 4. Operation indication

OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY

GREEN LED LIGHT (Power)

Indication of the switch's

power supply

OFF – no power supply of the switch

ON – power supply on, normal operation

OPTICAL INDICATION AT THE PoE PORTS (1÷4)

GREEN LED LIGHT (PoE)

Indication of the PoE power

supply at the RJ45 ports

OFF- no power supply at the RJ45 port (the device is not connected or not compliant

with the IEEE802.3af/at standard)

ON – supply at the RJ45 port

Blinking – short-circuit or output overload

YELLOW LED LIGHT (LINK)

The connection status of LAN

devices, 10/100/1000Mb/s

and data transmission

OFF- no connection

ON - the device is connected; 10/100/1000Mb/s

Blinking – data transmission

OPTICAL INDICATION AT THE UP LINK PORTS

GREEN LED LIGHT

OFF- no connection/ the device is connected 10/100 Mb/s

ON – the device is connected 1000 Mb/s

YELLOW LED LIGHT (LINK)

The connection status of LAN

devices and data transmission

OFF- no connection

ON - the device is connected 10/100/1000Mb/s

Blinking – data transmission

YELLOW LED LIGHT (SFP)

The connection status of LAN

devices and data transmission

OFF- no connection

ON - the device is connected

Blinking – data transmission

6

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household waste.

According to the European Union WEEE Directive, waste electrical and electronic equipment should

be disposed of separately from normal household waste.

Pulsar sp. j.

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

Pulsar SFG64F1 Instrukcja obsługi

Pulsar SFG64F1 Instrukcja obsługi

w innych językach

Powiązane dokumenty