AAT NVIP-4V-8002M Instrukcja obsługi

User’ s ma n ual

(shor t for m )

NVIP-4V-8002M

NVIP-4V-8002M User’s manual (short) ver.1.1

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/EU) and LVD (2014/35/EU) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and

national regulations implementing the directives:

• Electromagnetic compatibility EMC 2014/30/EU.

• Low voltage LVD 2014/35/EU with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well

as 75VDC and 1500VDC.

WEEE WEEE 2012/19/UE directive

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical

and Electronic Equipment (2012/19/UE) and further amendments. By ensuring this product is

disposed of correctly, you will help to prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste

handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for

used up electrical and electronic equipment for recycling purpose. For more information about

recycling of this product, please contact your local authorities, your household waste disposal service

or the shop where you purchased the product.

RoHS Directive 2011/65/UE

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances

in electrical and electronic equipment, have been designed and manufactured in compliance

with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have

negative impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

NVIP-4V-8002M User’s manual (short) ver.1.1

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding S.A. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-4V-8002M User’s manual (short) ver.1.1

4

TABLE OF CONTENTS .................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General Characteristics ........................................................................................ 5

1.2. Specification .................................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents .............................................................................................. ...8

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 9

2.1. Description of connectors and control tools ........................................................ 9

2.2 Camera mounting ............................................................................................... 10

2.3. Connecting Ethernet cable ................................................................................. 11

2.4. Starting the IP camera ....................................................................................... 12

2.5. Initial configuration via the Web browser ......................................................... 13

2.6. Security recommendations for network architecture and configuration ........... 14

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 15

3.1. Recommended PC specification for web browser ............................................. 15

3.2. Connection with IP camera via web browser ..................................................... 15

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 18

4.1. Displaying live pictures. ..................................................................................... 18

4.2. Adding a site to the Compatibility View list ..................................................... 19

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 19

5.1. Connecting power supply to the camera. .......................................................... 19

5.2. SD card installation ............................................................................................ 20

5.3. Connecting alarm input and output ................................................................... 20

6. RESTORING FACTORY DEFAULTS .................................................................... 21

6.1. Restoring software factory defaults.................................................................... 21

6.2. Restoring hardware factory defaults in IP cameras ........................................... 21

TABLE OF CONTENTS

NVIP-4V-8002M User’s manual (short) ver.1.1

5

1. FOREWORD INFORMATION

1.1. General Characteristics

• Imager resolution: 4 megapixels

• Mechanical IR cut filter

• IR operation capability

• Min. Illumination from 0.06 lx/F=1.3

• Wide Dynamic Range (WDR with double sensor scan) 120dB

• Digital Slow Shutter (DSS)

• Digital Noise Reduction (DNR)

• Defog Function (F-DNR)

• Digital Image Stabilization (DIS)

• Highlight Compensation (HLC)

• Back Light Compensation (BLC)

• Lens type: motor zoom, f=2.7mm ~ 12mm, F=1.3

• Built-in IR illuminator, 4 LEDs

• 1 Alarm input and 1 alarm output

• Video Compression: H.264, H.264+, H.265, H.265+, M-JPEG

• Max video processing resolution: 2592 x 1520

• Multi streaming: individually defined compression, resolution, speed and quality

• RTP/RTSP protocol support for video transmission

• Built-in webserver: camera configuration through the website

• MicroSD card support to 128GB

• Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,

saving file on SD card, alarm output activation

• Network protocol support : HTTP, TCP/IP, IPv4/IPv6, UDP, HTTPS, FTP, DHCP, DNS, NTP,

RTSP, RTP, UPnP, PPPoE, SMTP, RTCP

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

• Enclosure vandal proof IK10

• Degree of protection IP66

• Built-in Heater

• Power supply: 12VDC, PoE (Power over Ethernet)

• Surge protection TVS 4000 V

FOREWORD INFORMATION

NVIP-4V-8002M User’s manual (short) ver.1.1

6

1.2. Specification

FOREWORD INFORMATION

Image

Image Sensor 4 MPX progresive scan CMOS sensor 1/3” OV

Number of Effective Pixels 2688 (H) x 1520 (V)

Min. Illumination

0.06 lx/F1.3 - color mode,

0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1/5 s ~ 1/20000 s

Digital Slow Shutter (DSS) Up to 1/5 s

Wide Dynamic Range (WDR) yes (double scan sensor), 120dB

Digital Image Stabilization (DIS) yes

Digital Noise Reduction (DNR) 2D, 3D

Defog Function (F-DNR) yes

Highlight Compensation (HLC) yes

Kompensacja tylnego światła (BLC) yes

Lens

Lens Type motor-zoom, auto-iris function, f=2.7 ~ 12 mm/F1.3

Auto-focus zoom trigger, day/night mode trigger, manual trigger

Day/night

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Switching Level Adjustment yes

Switching Delay 0 ~ 180 s

Switching Schedule yes

Visible Light Sensor yes

Network

Stream Resolution

2592 x 1520, 2560 x 1440 (QHD), 2304 x 1296, 1920 x 1080 (Full HD), 1280 x 720 (HD),

704 x 576, 640 x 480 (VGA), 640 x 360, 352 x 288 (CIF), 320 x 240 (QVGA)

Frame Rate 30 fps for 2592 x 1520 and lower resolutions

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.264+, H.265, H.265+, MJPEG/G.711, RAW_PCM

Number of Simultaneous

Connections

max. 8

Bandwidth 21 Mb/s in total

Network Protocols Support HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DNS, NTP, RTSP, RTP, RTCP, SMTP, UPnP, PPPoE

ONVIF Protocol Support Profile S/G

Camera Configuration from Internet Explorer, languages: Polish, English, Russian, and others

Compatible Software NMS

Other functions

Privacy Zones 4

Motion Detection yes

Regions Of Interest (ROI) 8

Video Content Analysis (VCA)

tamper, abandoned object, object disappearance, line cross, zone entrance, double line cross,

loiter, multi loiter, abnormal speed, converse, illegal parking

Image Processing 180˚ image rotation, sharpening, mirror effect, corridor mode

Prealarm/Postalarm -/up to 86400 s

System Reaction to Alarm Events e-mail with attachment, saving file on FTP server, saving file on SD card, alarm output activation

IR LED

LED Number 4

Range 45 m

Angle 80°

Interfaces

Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x RCA/1 x RCA

Alarm Input/Output 1 (NO/NC)/1

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

Installation parameters

Dimensions (mm) 130 (Ф) x 112 (H

Weight 0.95 kg

Degree of Protection IP 66 (details in this user’s manual)

Enclosure vandal proof IK10 impact rating aluminium, white, poly-carbonate bubble

Power Supply PoE, 12 VDC

Surge protection TVS 4000 V

Power Consumption 5 W, 9 W (IR on.), 11.8 W (IR and heater on)

Operating Temperature -30°C ~ 60°C

Built-in Heater/Fan yes/no

To use the Video Content Analysis functions it is necessary to reduce the first stream frame rate to the 20 fps.

NVIP-4V-8002M User’s manual (short) ver.1.1

7

FOREWORD INFORMATION

1.3. Camera dimensions

All dimensions are in mm

NVIP-4V-8002M User’s manual (short) ver.1.1

8

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• 230 VAC / 12 VDC power supply

• Accessories bag

• Short version of user’s manual

• CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Short version of user’s manual

• Service BNC cable

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

Caution:

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

Caution:

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not compatible

with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that results from

the usage of improper power supply source are not covered by the warranty.

Caution:

Camera connectors / sockets are not hermetic. The user should ensure their hermeticity on his

own.

Caution:

Please note that the wall or ceiling must have enough strength to support the IP Camera.

Caution:

In order to obtain declared degree of protection please seal the camera base to prevent water

getting inside. Furthermore, when installing the camera on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

Caution:

The declared degree of protection of the camera relates to its housing and does not take into account

the possibility of moisture infiltration into the interior of the camera by connecting cables.

Connection cables protection through i.e. sealing up is the responsibility of the camera installer. The

manufacturer is not liable for any damages to the camera caused as a result of failing in performing

that activity by installer, which also means that camera damaged in that way is not subject to

warranty repairs.

FOREWORD INFORMATION

NVIP-4V-8002M User’s manual (short) ver.1.1

9

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Description of connectors and control tools

1. Visible Light Sensor

2. RESET button

3. Service video output connector (BNC)

4. MicroSD card slot

Description of electrical connectors:

1. 100 Mb/s Ethernet port (RJ-45)

2. Power supply 12VDC

3. Audio input (RCA)

4 Audio output (RCA)

5. Alarm IN/OUT

• Alarm COM0 (orange)

• Alarm IN0 (yellow)

• Alarm OUT1 (gray)

• Alarm COM1 (purple)

CAUTION: Pay special attention to the polarization while connecting 12VDC to the camera

START-UP AND INITIAL CAMERA CONFIGURATION

SCHEMA OF 12VDC POWER SUPPLY CONNECTOR

4

2

3

1

NVIP-4V-8002M User’s manual (short) ver.1.1

10

2.2. Camera mounting

START-UP AND INITIAL CAMERA CONFIGURATION

2.2. Camera mounting

1. Use the included allen key to remove the camera cover dome

screws (1) and remove cover dome.

2. Use the included mounting template or the camera to mark holes for

the mounting screws.

3. Drill holes in marked places.

There are two ways to mount camera:

Method 1: Direct Attach Install

4a. Remove 2 of the 3 base locking screws.

5a. Use 2 pieces of M3x72 screws to mount the camera directly to the

mounting surface.

6a. Remove the 3rd base locking screw and install the 3rd M3x72 screw.

Method 2: Camera Base Install

4b. Remove the camera base by unscrewing the 3 base

locking screws, and turn camera module approx. 5

degrees counterclockwise to detach camera base from

the camera module.

5b. Install the base to the correct holes as indicated on the

mount template using the M4x32 screws.

6b. Mount the camera to the base and fasten the fastening

screws

7. Ensure the rubber gasket inside the camera is properly

in place, then mount the camera cover dome and the

camera cover screws.

1

NVIP-4V-8002M User’s manual (short) ver.1.1

11

Camera module is placed on a mount allowing 3-axis module position adjustment.

WARNING!

Please pay attention to wires connecting camera module with camera body, while you are

adjusting camera module position.

2.3. Connecting Ethernet cable

To maintain tightness of Ethernet cable connection, please follow instruction below:

1. Loosen the nut (a) from the main element (b).

2. Run power cable (without RJ-45 connector) though both elements. Then crimp the cable with RJ-45

connector. Install rubber gasket (d) on the connector (c).

3. Connect the cable to the waterproof connector (c), screw main cover (b), then screw the nut (a).

Caution: The other camera connectors are not waterproof. User should seal them by himself.

Caution: It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that

results from the usage of improper power supply source are not covered by the warranty.

a

b

a

b

c

d

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-4V-8002M User’s manual (short) ver.1.1

12

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch

with PoE support (IEEE 802.3af).

You can also connect it directly via power supply adapter with parameters compatible with camera

power supply specification.

After connecting power status red LED placed inside the housing should light on. Initialization process

is then started which can take about 2 minutes. You can then proceed to connect to the camera via web

browser. .

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

• Connection utilising network switch with PoE support

• Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Power supply and

network transmission

Computer IP Camera

Network Switch

PoE

Network transmission

IP Camera

Network transmission

Network Switch

Computer

Network transmission

NVIP-4V-8002M User’s manual (short) ver.1.1

13

• Connection utilising external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter

with parameters specified in user’s manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

2.5. Initial configuration via the web browser

The default network settings for Novus camera are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-4V-8002M User’s manual (short) ver.1.1

14

2.6. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-4V-8002M User’s manual (short) ver.1.1

15

NETWORK CONNECTION UTILIZING WEB BROWSER

3. NETWORK CONNECTION VIA WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 2592 x 1520

resolution and 30 fps speed.

1. CPU Intel i5 3 GHz or faster

2. RAM Memory min. 4 GB

3. VGA card (any displaying Nvidia GeForce 512MB Ram memory)

4. OS Windows 7 / 8 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

Caution:

To maintain correct operation as snapshot or video recording you must enable the browser as an

administrator, also to maintain correct operation as playback from the microSD card you must

add IP camera address to Compatibility View in browser settings.

You have to enter camera IP address in the web browser address bar. If IP address is correct user login

window will be displayed:

Default user is root and default password is pass.

In the Language box you can change the display language. The default language is English.

For safety reasons, it is recommended to change default user name and password.

NVIP-4V-8002M User’s manual (short) ver.1.1

16

NETWORK CONNECTION VIA WEB BROWSER

If you’re first time running the camera, you will see screen as below.

To correctly camera working, you need a plugin, you have to download and install it as below.

• Click Download and setup

•

Download and setup

NVIP-4V-8002M User’s manual (short) ver.1.1

17

NETWORK CONNECTION VIA WEB BROWSER

• Click Install button

• After installation, click Finished button

Caution: In Windows Vista/7/8/10 the ActiveX applet may be blocked by Windows Defender or

User account control. In such case you should allow to run this applet, or simply disable these

functions.

Caution: If the installation fails, changing security settings for the IE browser is required. In order to do

that, please choose: Tools > Internet options > Security tab > Custom level and:

• Under Download unsigned ActiveX controls - select either Enable or Prompt

• Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

NVIP-4V-8002M User’s manual (short) ver.1.1

18

WWW INTERFACE - WORKING WITH IP CAMERA

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live video

1. Camera menu:

• Live Video - opens the camera live video

• Playback - opens the camera playback - to maintain correct operation you must add IP camera

address to Compatibility View in browser settings (look at 4.2 chapter)

• Configuration - opens the camera configuration menu

2. Change Password and Sign out buttons - are used to change the password and log off the

current user.

3. Live video preview

4. Stream information

5. Live video menu

• Selection of stream preview

• PTZ button - turn on PTZ window

• Selection of additional camera configuration - option not available

• Video button- turn-on/off camera preview output

• Live / Smooth Button- turn-on smooth preview option

• Audio button- turn-on/off audio output

• Interphone button- turn-on/off audio input and output

• Sensor button- turn-on sensor configuration menu

• Snapshot button- make a preview snapshot

• VCA button - turn on/off displaying graphical presentation of the Video

Content Analysis functions

1.

3.

4.

5.

2.

NVIP-4V-8002M User’s manual (short) ver.1.1

19

ELECTRIC CONNECTORS AND ACCESORIES

4.2 Adding a site to the Compatibility View list

1. Open Internet Explorer, select the Tools button and then select Compatibility View settings (1).

2. Under Add this website, enter the URL of the site you want to add to the list (2), and then select

Add (3).

5.

ELECTRIC CONNECTORS AND ACCESORIES

5.1. Connecting power supply to the camera.

The camera can be supplied only by power supplay with parameters compatible with camera specifi-

cation to power camera via power in jack.

SCHEMA OF 12VDC POWER SUPPLY CONNECTOR

Caution : Make sure to follow the correct polarity if connecting the camera to DC power. Po-

larity is marked on the power connector.

Caution: In order to provide protection against voltage surges/lightning strikes, usage of ap-

propriate surge protectors is advised. Any damages resulting from surges are not eligible for

service repairs.

Caution: It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that

results from the usage of improper power supply source are not covered by the warranty.

1.

2.

3.

NVIP-4V-8002M User’s manual (short) ver.1.1

20

ELECTRIC CONNECTORS AND ACCESORIES

5.2. microSD card installation

Camera supports microSD, cards with their capacity up to 128GB. In order to install the card properly,

please follow the instructions below:

• Turn the camera off.

• Unscrew screws holding camera dome cover using allen key and remove camera cover.

• Mount microSD card in the socket located at the camera’s base, according to the picture:

• Mount camera cover dome and screw to camera base.

• Turn the camera on

• Turn the camera on.

• Check the SD card by checking it in the Device Record -> Record Directory tab. Format The card I

necessary.

5.3. Connecting alarm inputs/outputs.

Description of connectors is in chapter 2.1.

Typical Alarm Input connection Typical Alarm Output connection

Caution: Alarm output relay max. load is: 12VDC/300mA

Strona jest ładowana ...

AAT NVIP-4V-8002M Instrukcja obsługi

AAT NVIP-4V-8002M Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty