6
EN
1. Operation: SET TEMPERATURE
1.1 Fill the container with (hot) water and make sure
that the water will not come over the edge on
the inner mark (groove) of the water tank. Re-
member that placing food in the water will also
raise the water level – it should still not pass
aforementioned groove. Water should be filled
up to the Max Mark no matter the amount of
food you are going to put into the water bath for
cooking
1.2 Connect the power plug to a suitable electrical
power outlet
1.3 Press the ON/OFF Icon.
1.4 Then blue LED in the ON/OFF Icon is ON. The
upper Temperature display will show the last
SET TEMPERATURE. The lower display will
show the appliance is in standby mode (----).
NOTE! The appliance beeps once for a short time
1.5 Press INCREASE/DECREASE Icon, the lower dis-
play will show, the heating element is switched
ON. At this moment, The Temperature Display
will show the ACTUAL TEMPERATURE. The low-
er Timer Display will show the last set time.
1.6 Now, press the Temperature Icon, the upper dis-
play will show the previous SET TEMPERATURE.
Lower display will show °C for 1 ~ 2 seconds. And
then show the time.
1.7 Then, press the INCREASE/DECREASE Icon to
adjust the SET TEMPERATURE within this 1 ~ 2
Seconds. The SET TEMPERATURE range is 40°C
~ 90°C.
Press once for +0,1˚C / -0,1˚C.
Press and hold for +1,0°C / -1,0˚C.
1.8 When stop to press INCREASE/DECREASE Icon,
the SET TEMPERATURE will be stored automat-
ically.
1.9 The Temperature Icon will blink until the SET
TEMPERATURE is reached. After reaching the
SET TEMPERATURE, the Temperature Icon
lamp will turn off and a short beep sound will be
heard and keep stay of within a range of +0,5˚C
/ -0,5˚C. If the Actual Temperature over the SET
TEMPERATURE about 1°C, the Temperature
Display will show “H0t”.
NOTE!
If you don’t put water into the water bath and try to
switch on the power by step 1.3 to 1.7, the thermal
protection of the appliance will act to stop the pow-
er. The upper Temperature Display will show the E2.
The lower Timer Display will show ----. And long
beep sound will be heard. The user can only switch-
es OFF the appliance to stop this warning signal.
2. Operation: SET TIMER
2.1 During cooking, you can activate the TIMER
function.
2.2 Press TIME Icon to set the TIMER. The upper
display will show “t”. Then, press INCREASE/
DECREASE Icon within 1 ~ 2 seconds to set the
TIMER. Press once for + 5,0 min / - 5,0 min. And
the lower display will show the “SET TIMER”.
And start count down after few seconds.
2.3 The “:” will blink until 00:00 and “END” will be
blinked continuously. Two short beep sound will
be heard and the “Timer Icon” will also light off.
Note: When the TIMER finish counting, the pow-
er of the appliance doesn’t switch OFF. The wa-
ter tank will continue to operate and keep the
temperature stable.
2.4 You can also press Timer Icon to start count
down from 00:00 in ascending order by press-
ing the Timer Icon once for 2 ~ 3 seconds. Press
again to cancel this function.
NOTE!
Time in count down can be adjusted all time
• During Timer is counting, if the user presses the
Timer icon, Timer counting will be suspended and
shows the time left
• In this moment, the user can adjust the Timer val-
ue
If during operation, water in the water bath has been
dry up, the thermal protection of the appliance will
act to stop the power. The upper Temperature Dis-
play will show the E2. The lower Timer Display will
show ----. And long beep sound will be heard. The
user can only switches OFF the appliance to stop
this warning signal.