AAT NVIP-5C-6400/F Instrukcja obsługi

User’ s ma n ual

(shor t for m )

NVIP-5C-6400/F

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/EU) and LVD (2014/35/UE) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national

regulations implementing the directives:

• Electromagnetic compatibility EMC 2014/30/EU.

• Low voltage LVD 2014/35/UE with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and

Electronic Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical and

electronic equipment, have been designed and manufactured in compliance with the above mentioned

regulations. Simultaneously, we claim that our products have been tested and do not contain

hazardous substances whose exceeding limits could have negative impact on human health or natural

environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual;

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics ......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...7

1.4. Package contents ............................................................................................... ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors and control tools ........................................................ 8

2.2. Mounting lens assembly ...................................................................................... 9

2.3. Starting the IP camera ........................................................................................ 10

2.4. Initial configuration via the web browser .......................................................... 11

2.5 Security recommendations for network architecture and configuration ........... 12

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 13

3.1. Recommended PC specification for web browser ............................................. 13

3.2. Connection with IP camera via web browser ..................................................... 13

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 15

4.1. Displaying live video. ......................................................................................... 15

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 16

5.1. Connecting power supply to the camera. .......................................................... 16

5.2. Camera control - RS-485. ................................................................................... 16

5.3. Connecting alarm input and output .................................................................... 16

5.4. SD card installation ........................................................................................... 17

6. RESTORING FACTORY DEFAULTS ..................................................................... 18

6.1. Restoring software factory defaults via web browser ........................................ 18

6.2. Restoring software factory defaults via NMSIPTool……… ... ………………..18

6.3 Restoring hardware factory defaults by hardware .. ………………..…………...19

TABLE OF CONTENTS

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

5

1. FOREWORD INFORMATION

1.1. General Characteristics

• Imager resolution: 5.0 megapixels

• Mechanical IR cut filter IR operation capability

• Min. Illumination from 0.003 lx

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• Digital Noise Reduction (DNR)

• Built-in webserver: camera configuration through the website

• Video compression: H.264, H.264+, H.265, H.265+, MJPEG / Audio compression: G711

• Max video resolution: 2592 x 1944

• The compression, resolution, speed and quality can be defined individually for each stream

• Supports up to 3 streams

• RTP/RTSP protocol support for video transmission

• ROI zones

• Memory SD Card Slot up to 128 GB

• Audio input / Audio output

• BNC output

• Wide range of responses to alarm events: e-mail with attachment, saving file on FTP, SD card,

alarm output activation

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

• Video Content Analysis (VCA):

- tamper

- abandoned object

- object disappearance

- line cross

- zone entrance

- object counting

- multi loiter

- face detection

- scene change

- video blurred

- video color cast

• Face recognition - advanced analytic function, available only with selected models of the NVR

6000 series.

• Power supply: 12 VDC / 24 VAC / PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 5 MPX CMOS sensor 1/2.5” APTINA

Number of Effective Pixels 2592 (H) x 1944 (V)

Min. Illumination

0.03 lx/F1.2 - color mode,

0.003 lx/F1.2 - B/W mode

Electronic Shutter auto/manual: 1/3 s ~ 1/100000 s

Digital Slow Shutter (DSS) up to 1/3 s

Wide Dynamic Range (WDR) yes (double scan sensor), 120dB

Digital Noise Reduction (DNR) 2D, 3D

Defog Function (F-DNR) yes

Highlight Compensation (HLC) yes

Back Light Compensation (BLC) yes

Reduction of image flicker (Antiflicker) yes

LENS

Compatible Mount Type CS

Iris Mode D

DAY/NIGHT

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Switching Level Adjustment yes

Switching Delay 2 ~ 120 s

Switching Schedule yes

NETWORK

Stream Resolution

2592 x 1944, 2592 x 1520, 2560 x 1440 (QHD), 2304 x 1296, 1920 x 1080

(Full HD), 1280 x 720 (HD), 640 x 480 (VGA), 320 x 240 (QVGA)

Frame Rate 30 fps for each resolution, 60 fps for 1920 x 1080 (Full HD)

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.264+,H.265, H.265+, MJPEG/G.711

Number of Simultaneous Connections max. 6

Bandwidth 60 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, IPv4/v6, UDP, HTTPS, Multicast, FTP, DHCP, DDNS, NTP,

SNTP, RTSP, UPnP, SNMP, QoS, IEEE 802.1X, PPPoE, SMTP, SSL, ICMP, Unicast

ONVIF Protocol Support Profile S/G

Camera Configuration

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compatible Software NMS, NVR-6000 Viewer

OTHER FUNCTIONS

Privacy Zones 4 video mask type: single color, or 1 video mask type: mosaic

Motion Detection yes

Region of interest (ROI) 3

Video Content Analysis (VCA)

tamper, abandoned object, object disappearance, line cross, zone entrance,

multi loiter, face detection, scene change, video blurred, video color cast

Image Processing

180˚ image rotation, sharpening, mirror effect, corridor mode, vertical flip,

horizontal flip

Prealarm/Postalarm -/up to 120 s

System Reaction to Alarm Events

e-mail with attachment, saving file on FTP server, saving file on SD card, alarm

output activation

INTERFACES

Video Output BNC, 1.0 Vp-p, 75 Ohm

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output 1 (NO/NC)/1 relay type

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot SD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm) 70 (W) x 60 (H) x 140 (L)

Weight 0.4 kg

Enclosure aluminium, white

Power Supply PoE, 12 VDC, 24 VAC

Power Consumption 4 W

Operating Temperature -20°C ~ 50°C

Operating temperature with housing -40°C ~ 50°C

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions

Camera NVIP-5C-6400/F

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate

surge protectors is advised. Any damages resulting from surges are not eligible for service re-

pairs.

Caution:

Please note that the wall or ceiling must have enough strength to support the IP Camera.

140 mm

70 mm

60 mm

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

8

START-UP AND INITIAL IP CAMERA CONFIGURATION

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1 Description of connectors and control tools

1. Reset button - hold it for 10 sec then release to restore to factory default

2. Audio input (mini jack (3.5 mm))

3. Audio output (mini jack (3.5 mm))

4. Video output - BNC, 1.0 Vp-p, 75 Ohm

5. Power connection indicator

6. SD card slot

7. Alarm NO - COM - Alarm output, normal open

8. Alarm IN - GND - Alarm input

9. RS485 connector

10. 10/100 Mb/s Ethernet port (PoE RJ-45 connector)

11. Power supply 12VDC, 24VAC

Camera can be supplied using external power supply unit corresponding with the camera parameters

or by using RJ45 network socket and PoE (802.3af) power supply unit.

CAUTION!!!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not com-

patible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that

results from the usage of improper power supply source are not covered by the warranty.

DC12V/AC24V

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2 Mounting lens assembly

1. Set screw Ring focusing lens (Back focus)

2. Ring focusing lens (Back focus)

3. The interface to control the iris of the lens and its polarization

Lens Mount:

1. Remove the protecting element.

2. Attach the C/CS lens adapter if necessary.

3. Attach the lens to the camera by turning it clockwise.

4. Plug in the interface to control the iris of the lens.

5. Plug in other necessary wires.

6. Unscrew set screw, adjust “Back Focus” if necessary and screw counter screw.

Information:

To mount C type lens you should use additional C/CS adapter (not included)

C-mount lens

CS-mount lens

C/CS adapter

3

2

1

Back focus ring

Set screw

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

10

2.3. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network PoE switch

with PoE support (IEEE 802.3af).

You can also connect it directly via power supply adapter with parameters compatible with camera

power supply specification.

After connecting power status red LED should light on. Initialization process is then started which can

take about 2 minutes. You can then proceed to connect to the camera via web browser.

The recommended way to start an IP camera and perform its configuration is a connection directly

to the network switch which is not connected to other devices. To obtain further information about

network configuration parameters (IP address, gateway, network mask, etc.) please contact your

network administrator.

• Connection utilising network switch with PoE support

• Connection utilising external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network Switch

Computer

Network transmission

Power supply and

network transmission

Computer

IP Camera

Network PoE Switch

Network transmission

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

11

• Connection utilising external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

2.4. Initial configuration via the web browser

The default network settings for NVIP-5C-6400/F camera are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

12

2.5. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

13

3. NETWORK CONNECTION UTILIZING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 2592x1944 resolution and 25 fps speed.

1. CPU Intel i7 3 GHz or faster

2. RAM Memory min. 6 GB

3. VGA card (any displaying Nvidia GeForce 1GB Ram memory)

4. OS Windows 7 / 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

Caution:

To maintain correct operation as snapshot or video recording you must enable the browser as an

administrator.

You have to enter camera IP address in the web browser address bar. If IP address is correct user login

window will be displayed:

In the Language box you can change the display language. Available languages: Polish, English and

other.

Caution!

Default user is root and default password is pass. The camera will ask you to change the default

password during the first login (recommended). To do this, check the Modify password option and then

enter and confirm the new password. In order to log into the camera without changing the password,

press the OK button. The message will be displayed each time you log in, until you change your

password, or select the Do not show again option.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

14

If you’re first time running the camera, you will see screen as below.

To correctly camera working, you need a plugin, you have to download and install ActiveC plugin.

To do it just click Save button, than Run, close IE browser, choose the language, click Install button

and ay the end click Finish button. After installation run IE browser.

Caution: In Windows Vista/7/8/8.1/10 the ActiveX applet may be blocked by Windows Defender or

User account control. In such case you should allow to run this applet, or simply disable these

functions.

Caution: If the installation fails, changing security settings for the IE browser is required. In order to

do that, please select Enable for Initialize and script ActiveX controls not marked as safe and Download

unsigned ActiveX controls option

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

15

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1 Displaying live video

1. Camera menu

• Live - opens the camera live video

• Config - opens the camera configuration menu

• Search - opens the camera playback

• Logout - button used to log out the current user

2. The buttons for changing the displayed stream and fluency - let you change the displayed stream to

Main stream, Sub stream and Third stream, and also allow you to choose between Real-time, Balanced

and Fluent fluency.

3. Alarm icons - icons showing the current status of some camera alarms.

4. Live video preview window

5. Image settings buttons - these buttons change the picture display mode in the live video preview

Original size Adapt

Proper size Full screen

6. Function buttons - these buttons allow you to enable / disable some of functions

Stop live view Snapshot Start two-way audio

Enable/disable Audio Start recording PTZ functions

Zoom In / Zoom Out (digital)

WWW INTERFACE - WORKING WITH IP CAMERA

3.

4.

6.

5.

2.

1.

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

16

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the

camera parameters or by using RJ45 network socket and PoE (802.3af) power

supply unit. If you’re using external power supply pleas connect wires according

to polarisation shown on picture:

Information:

Power supply adapter is not included. Please use power adapter with parameters

specified in user’s manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate

surge protectors is advised. Any damages resulting from surges are not eligible for service

repairs.

5.2. Camera control - RS-485

By using the RS485 interface can control an external camera PTZ domes. For this purpose, use the

RS-485 port on the rear of the camera. Camera got default settings for protocol (Pelco-P, 4800).

5.3. Alarm input and output connection

Standard alarm input connection Standard alarm output connection

ELECTRIC CONNECTORS AND ACCESORIES

IP

Camera

PTZ

Device

RS-485

+

-

+

-

+ -

DC 12V

AC 24V

Alarm input

(IN)

Alarm input

(GND)

IP camera

Switch or

sensor

Indicator

power supply

IP camera

Indicator

Alarm

output

(COM)

Alarm

output

(NO)

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

17

ELECTRIC CONNECTORS AND ACCESORIES

5.4 SD card installation

Camera supports SD cards up to a maximum size of 128GB. In order to install the card properly, please

follow the instructions below:

• Turn off the camera

• Unscrew cover located at the camera back

• Mount SD card in the socket

• Mount card cover and screw to camera back.

• Turn the camera on

• Check the SD card by checking its capacity in the “System Config” -> “SD Card” tab.

SD card slot

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

18

RESTORING FACTORY DEFAULTS

6. RESTORING FACTORY DEFAULTS

NOVUS IP cameras allow to restore defaults via:

• software (via web browser )

• software (via NMSiptool)

• hardware (using reset button (DEFAULT))

6.1. Restoring software factory defaults via web browser

User can restore default settings of the IP camera except network settings (optional). To restore to

default settings go to: “Advanced Config -> Config Backup & Restore” tab. Process of restoring takes

about two minutes.

6.2. Restoring software factory defaults via NMSIPTool

NMSip (version 1.23.4 or later) allows to restore factory defaults. To restore settings find camera via

NMSIPTool, click right mouse button and choose “ Restore default configuration”. Next, within 30

seconds, it is required to turn the camera power off and on.

NVIP-5C-6400/F - User’s manual (short form) ver 1.0

19

6.3. Restoring factory defaults by hardware

In order to restore factory defaults for the camera please follow the instructions:

• Press the reset button (DEFAULT) and hold on for 10 seconds

• Release button

• Log on after approx. 1 minute seconds using default IP address (http://192.168.1.200) and default

user name (root) and password (pass)

RESTORING FACTORY DEFAULTS

Reset

2019-12-09 MO, JB

AAT Holding S.A., 431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

Strona się ładuje...

AAT NVIP-5C-6400/F Instrukcja obsługi

AAT NVIP-5C-6400/F Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty