Yamaha PSS-A50 Instrukcja obsługi

Marka: Yamaha

Model: PSS-A50

Typ: Instrukcja obsługi

PSS-A50

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply

(adapter). DO NOT connect this product to any power supply or

adapter other than one described in the manual, on the name

plate, or specifically recommended by Yamaha.

WARNING: Do not place this product in a position where any-

one could walk on, trip over, or roll anything over power or con-

necting cords of any kind. The use of an extension cord is not

recommended! If you must use an extension cord, the minimum

wire size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller

the AWG number, the larger the current handling capacity. For

longer extension cords, consult a local electrician.

This product should be used only with the components supplied

or; a cart, rack, or stand that is recommended by Yamaha. If a

cart, etc., is used, please observe all safety markings and instruc-

tions that accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct

at the time of printing. However, Yamaha reserves the right to

change or modify any of the specifications without notice or obli-

gation to update existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound

levels that could cause permanent hearing loss. DO NOT operate

for long periods of time at a high volume level or at a level that is

uncomfortable. If you experience any hearing loss or ringing in

the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches

are stable and any optional fixtures (where applicable) are well

secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No

other uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to

how a function or effect works (when the unit is operating as

designed) are not covered by the manufacturer’s warranty, and

are therefore the owners responsibility. Please study this manual

carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and

environmentally friendly. We sincerely believe that our products

and the production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the law, we

want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which

(if applicable) is soldered in place. The average life span of this type

of battery is approximately five years. When replacement becomes

necessary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of

these may be rechargeable. Make sure that the battery being

charged is a rechargeable type and that the charger is intended for

the battery being charged.

When installing batteries, never mix old batteries with new ones,

and never mix different types of batteries. Batteries MUST be

installed correctly. Mismatches or incorrect installation may result in

overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly

and as regulated by the laws in your area. Note: Check with any

retailer of household type batteries in your area for battery dis-

posal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some

reason its useful life is considered to be at an end, please

observe all local, state, and federal regulations that relate to the

disposal of products that contain lead, batteries, plastics, etc. If

your dealer is unable to assist you, please contact Yamaha

directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The

model number, serial number, power requirements, etc., are

located on this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided below

and retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

PSS-A50

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your author-

ity, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements pro-

vides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment gen-

erates/uses radio frequencies and, if not installed and used

according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product

is found to be the source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America, Elec-

tronic Service Division, 6600 Orangethorpe Ave, Buena Park,

CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(Supplier’s declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Keyboard

Model Name : PSS-A50

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

* This applies only to products distributed by

Yamaha Corporation of America.

(FCC SDoC)

PSS-A50 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the

following:

• Do not place the USB cable near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the

cable, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Included USB cable is designed for use with only this instrument. Do

not use for any other instrument.

• Check the plug periodically and remove any dirt or dust which may

have accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the

instrument or attempt to disassemble or modify the internal

components in any way. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualified

Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases, bottles or

glasses) containing liquids which might spill into any openings. If any

liquid such as water seeps into the instrument, turn off the power

immediately and disconnect the plug from the AC outlet. Then have the

instrument inspected by qualified Yamaha service personnel.

• Never insert or remove a plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item

may fall over and cause a fire.

• Magnetism may affect electro-medical devices.

- Do not use this product near medical devices or inside areas in

which the use of radio waves is restricted.

- Do not use this product within 15cm (6 in.) of persons with a heart

pacemaker or defibrillator implant.

• Follow the precautions below. Failure to do so might result in

explosion, fire, overheating or battery fluid leakage.

- Do not tamper with or disassemble batteries.

- Do not dispose of batteries in fire.

- Do not attempt to recharge batteries that are not designed to be

charged.

- Keep the batteries separate from metallic objects such as necklaces,

hairpins, coins, and keys.

- Use the specified battery type (page 13) only.

- Use new batteries, all of which are the same type, same model, and

made by the same manufacturer.

- Always make sure all batteries are inserted in conformity with the +/-

polarity markings.

- When the batteries run out, or if the instrument is not to be used for a

long time, remove the batteries from the instrument.

- When using Ni-MH batteries, follow the instructions that came with

the batteries. Use only the specified charger device when charging.

• Keep batteries away from small children who might accidentally

swallow them.

• If the batteries do leak, avoid contact with the leaked fluid. If the battery

fluid should come in contact with your eyes, mouth, or skin, wash

immediately with water and consult a doctor. Battery fluid is corrosive

and may possibly cause loss of sight or chemical burns.

• When one of the following problems occur, immediately turn off the

power switch and disconnect the plug from the outlet. (If you are using

batteries, remove all batteries from the instrument.) Then have the

device inspected by Yamaha service personnel.

- The USB cable or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

- If any cracks or breakages exist on the instrument.

Power supply

Do not open

Water warning

Fire warning

Influences on electro-medical devices

Battery

If you notice any abnormality

DMI-7 1/2

PSS-A50 Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Use the specified USB power adaptor (page 7) only. Using the wrong

adaptor can result in damage to the instrument or overheating.

• Do not connect the instrument to an electrical outlet using a multiple-

connector. Doing so can result in lower sound quality, or possibly

cause overheating in the outlet.

• When removing the plug from the instrument or an outlet, always hold

the plug itself and not the USB cable. Pulling by the cable can damage

it.

• Remove the plug from the outlet when the instrument is not to be used

for extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• Before moving the instrument, remove all connected cables, to prevent

damage to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug from the

outlet. Even when the power switch is turned off, electricity is still

flowing to the product at the minimum level. When you are not using

the product for a long time, make sure to disconnect the plug from the

wall AC outlet.

• Before connecting the instrument to other electronic components, turn

off the power for all components. Before turning the power on or off for

all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels

and gradually raise the volume controls while playing the instrument to

set the desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on

the panel or keyboard. This could cause physical injury to you or

others, damage to the instrument or other property, or operational

failure.

• Do not rest your weight on, or place heavy objects on the instrument,

and do not use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of

time at a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or ringing

in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you disconnect the plug from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

DMI-7

2/2

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property, fol-

low the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Otherwise, the

instrument, TV, or radio may generate noise.

• Do not expose the instrument to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a heater, or in a

car during the day) to prevent the possibility of panel disfiguration,

damage to the internal components or unstable operation. (Verified

operating temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since

this might discolor the panel or keyboard.

 Maintenance

• When cleaning the instrument, use a soft and dry cloth. Do not use

paint thinners, solvents, alcohol, cleaning fluids, or chemical-

impregnated wiping cloths.

 Saving data

• Some of the data of this instrument (page 13) are retained when the

power is turned off. However, the saved data may be lost due to some

failure, an operation mistake, etc.

Information

 About copyrights

• Copying of the commercially available musical data including but not

limited to MIDI data and/or audio data is strictly prohibited except for

your personal use.

• This product incorporates and bundles contents in which Yamaha owns

copyrights or with respect to which Yamaha has license to use others'

copyrights. Due to copyright laws and other relevant laws, you are NOT

allowed to distribute media in which these contents are saved or

recorded and remain virtually the same or very similar to those in the

product.

* The contents described above include a computer program, Accompaniment

Style data, MIDI data, WAVE data, voice recording data, a score, score data, etc.

* You are allowed to distribute medium in which your performance or music

production using these contents is recorded, and the permission of Yamaha

Corporation is not required in such cases.

 About this manual

• The illustrations and displays as shown in this manual are for

instructional purposes only, and may appear somewhat different from

those on your instrument.

• The company names and product names in this manual are the

trademarks or registered trademarks of their respective companies.

Power supply

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

PSS-A50 Owner’s Manual

Thank you for purchasing this Yamaha Digital Keyboard!

This instrument provides powerful performance features including versatile effects and sounds enjoyable

even for beginners. We recommend that you read this manual carefully so that you can fully take advantage

of the advanced and convenient functions of the instrument.

We also recommend that you keep this manual in a safe and handy place for future reference.

About the Manuals

In addition to this Owner’s Manual, the following

Online document (PDF file) is available.

MIDI Reference

Contains MIDI-related information, such as

the MIDI Implementation Chart.

To obtain this document, access the Yamaha

Downloads website, then enter the model name for

searching the desired files.

Yamaha Downloads

http://download.yamaha.com/

Included Accessories

• Owner’s Manual (this book) (1)

• USB cable (1)

• Online Member Product Registration (1)

Setting Up

Depending on how you are powering your instru-

ment, follow one of the three power supply instruc-

tions below. The PSS-A50 does not include power

supply accessories (with the exception of the USB

cable), so make sure to purchase them separately

as required.

Using USB Bus Power

Connect the included USB cable in the order

shown in the illustration.

When disconnecting the USB cable, first turn off

the power, then follow the order shown above in

reverse.

USB bus power

This instrument is a bus-powered type device which can be

Computer

5V DC/

USB TO HOST jack

(USB micro B)

USB cable

Rear

PHONES/OUTPUT Jack

For connecting a set of stereo headphones with a

stereo mini plug. This jack also functions as an

external output for sending the audio signal of this

instrument to external audio equipment.

The speakers of the instrument are automatically

shut off when a headphones plug, etc. is inserted

into this jack.

• Before using the headphones, be sure to set the volume of the instrument at the minimum level. Then gradually raise the

volume while playing the instrument, for your ear comfort and safety.

CAUTION

Rear

• Do not use the instrument or headphones for a long

period of time at a high or uncomfortable volume level,

since this can cause permanent hearing loss.

• Before connecting the instrument to other electronic com-

ponents, make sure to set all volume levels to minimum,

then turn off the power off all the components. Otherwise,

damage to the components or electrical shock may occur.

• To avoid possible damage to the external device, first turn

on the power to the instrument, then to the external

device. When turning off the power, do so in reverse

order: first turn off the power to the external device, then

to the instrument.

CAUTION

NOTICE

PSS-A50 Owner’s Manual

Using a USB Power Adaptor or USB

Mobile Battery

Connect the included USB cable and the USB

power adaptor (or USB mobile battery) sold sepa-

rately in the order shown in the illustration.

When disconnecting the USB cable or so, first turn

off the power, then follow the order shown above in

reverse.

Using Batteries

This instrument requires four “AA” size, Alkaline

(LR6)/Manganese (R6) batteries, or rechargeable

nickel-metal hydride batteries (rechargeable Ni-MH

batteries). The Alkaline batteries or rechargeable

Ni-MH batteries are recommended for this instru-

ment, since other types may result in poorer battery

performance.

1 Make sure that the power of the instrument is

off.

2 Open the battery compartment cover located on

the instrument’s bottom panel.

3 Insert the four new batteries, being careful to fol-

low the polarity markings on the inside of the

compartment.

4 Replace the compartment cover, making sure

that it locks firmly in place.

USB cable

AC Outlet

USB mobile battery

(commercially available)

USB power adap-

tor (commercially

available)

5V DC/

USB TO HOST jack

(USB micro B)

The shape of the plug and outlet

differs depending on your locale.

Rear

USB Power adaptor / USB mobile battery

requirements

• Output voltage: 4.8 V to 5.2 V

• Output current: 0.5 A or greater

• Make sure to use a USB power adaptor or USB mobile

battery with the specifications above. Using the wrong

USB power adaptor can result in damage to the instru-

ment or overheating.

Read the safety precautions for your particular USB

power adaptor or USB mobile battery.

• When the instrument is turned on and power turns off

suddenly and unexpectedly, your USB power adaptor

may not meet the requirements or may be damaged.

Try using another USB power adaptor that meets the

requirements, etc. If it should appear to be malfunc-

tioning, please consult Yamaha service personnel.

CAUTION

NOTICE

• See the “Battery” section in the Precautions (pages 4–5).

• Make sure to set the Battery Type correctly (page 12).

Failure to set the battery type may shorten the amount of

the battery life.

• Connecting or disconnecting the USB cable with batteries

installed may turn the power off, resulting in loss of data

being recorded at the time.

WARNING

NOTICE

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the bottom

of the unit. You should note this serial number in the space pro-

vided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

• Use a USB cable of less than 3 meters. If the sound is degraded, make sure to use the included USB cable or turn down the

master volume as needed.

NOTICE

2 3

PSS-A50 Owner’s Manual

Turning the Power On/

Standby

Turning the power on

Press the [ ](Standby/On) switch.

The display lights.

Turning the power to Standby

Press the [ ](Standby/On) switch for a second.

0.01

Adjusting the Master

Volume

Volume range: 00–15 (default: 13)

NOTE

• Volume will be reset to the default value of 13 when

“Initialization” (page 13) is done.

Decreases Increases

Octave Shift

You can shift the pitch up or down in octave

steps.

Changing the pitch

NOTE

• To reset the octave setting to the default value of “00,”

press the OCTAVE buttons simultaneously.

• When the Octave setting is -03, -04, +03 or +04, some

Voice sounds too soft to hear, or the pitch in one octave

sounds same as other (up or down) octave.

Down Up

Octave value “-04” –

“04” will be shown.

Arpeggio

This function lets you automatically trigger musi-

cal and rhythmic phrases and backing patterns

by simply pressing a key or keys on the keyboard.

Select an Arpeggio type.

Use the [-] and [+] buttons.

NOTE

• Refer to the Arpeggio category list on the panel.

• Holding down the [-] or [+] button continuously

decreases or increases the value. While holding down

the [SHIFT] button, each press of the [-] or [+] button

jumps to each Arpeggio category top.

• No. 117–138 are drum patterns. Play with a Drum Kit

Voice and “Hold” (page 9) to use it as a rhythm track.

• Selecting a Voice automatically selects the optimum

Arpeggio type for the Voice.

00.1

Selected type number

will be shown.

This dot lights to indicate

an Arpeggio number.

0.0.1

PSS-A50 Owner’s Manual

Arpeggio Hold

The Arpeggio cycles automatically, even if you

release your fingers from the keys. You can play

the keys over the Arpeggio sound.

Press [ARP. HOLD] button while the Arpeggio

is playing.

To disable Arpeggio Hold, press the [ARP. HOLD]

button again.

NOTE

• During Arpeggio Hold, you can change Arpeggio phrases

by pressing desired keys while holding down the [ARP.

HOLD] button.

• When Arpeggio Hold is disabled, the last Voice selected

before entering Arpeggio Hold will be called up.

Start the Arpeggio sequence.

Press the [ARPEGGIO] button.

Hold keys to start Arpeggio sequence.

Turn off Arpeggio

Press the [ARPEGGIO] button.

Aon

(on)

The Arpeggio sequence

changes in response to the

actual notes or chords you play.

AoF

If you can’t hear any sound or the sound is too

soft, try the following.

• Increase the volume.

• Disconnect the headphones from the

PHONES/OUTPUT terminal.

• Set Local Control to On (page 12.)

• Replace all the batteries with new ones or

recharged ones (page 7.)

• Reset the Octave setting to the default

value of 00.

Selecting the Keyboard Sound (Voice)

Various instrumental Voices are categorized and

assigned to the Voice buttons. Pressing the

same Voice button repeatedly selects the

assigned Voices in order.

NOTE

0.01

VOICE buttons

Selected Voice number

will be shown.

This dot lights to indicate a Voice

number.

• For specific Voice names, refer to page 14.

• Voice numbers 039 and 040 in the [DRUM/PERC.] button

are Drum Kit Voice. Various drum and percussion sounds

are assigned to individual keys, from which they can be

played. For details on the instruments and key assignments

of each Drum Kit, see page 16.

PSS-A50 Owner’s Manual

Recording/Playing

You can record your performance (Phrase Recording). Note that the previously recorded data will be

erased since only one recording is available.

Recording

Standby

Press [REC].

To exit from Record-

ing Standby mode,

press [REC] again.

Start recording

Play the keyboard to

start recording.

You can also start

recording by press-

ing [/].

Stop recording

Press [REC].

Playback

Press [/].

rEC

(Recording Standby)

rEC.

(Dot flashes with beat)

[SHIFT] button

• Sets the various setting of the instru-

ment (page 12: keyboard settings)

• Selects the function boxed. (TYPE of

Motion Effect; , PORTA-

MENTO; )

NOTE

• When recording capacity becomes full during recording, a “FUL” message appears on the display and recording is stopped.

• You can start a Phrase at a desired speed by simply tapping the [TEMPO/TAP] button four times for time signatures in 4 (such as

4/4) or three times for time signatures in 3 (such as 3/4).

Time Signature

When recording the Phrase used for Repeat Playback (page

11), set the Time Signature during the Recording Standby

mode (“rEC” indication.) If you recorded with a wrong Time

Signature, unwanted silence may be inserted during the

repeats since the Phrase is repeated in measures. The Time

Signature can be set from “Metronome” on page 12. (The

default setting is 4/4.) You can use the metronome while

recording, but the metronome will not be recorded.

Motion Effect

While holding down the [MOTION EFFECT] but-

ton, Motion Effect applies to the notes you play.

Motion Effect has three types A, B and C, and

correspondingly changes the Filter, Pitch, and/or

Modulation of the sound over time. Each type

has around 10 variations.

Selecting a Desired Type

While holding down the [SHIFT] button, each

press of the [MOTION EFFECT] button selects

the type in order (A01, A02, etc.).

NOTE

• To jump to the top of the A, B or C type in order, hold

down the [MOTION EFFECT] button while holding

down the [SHIFT] button.

• Certain combinations of a specific Voice, octave and

type may generate noise.

A01

Selected type and number will

be shown.

0.0.1

1 3

PSS-A50 Owner’s Manual

Portamento

Create a smooth transition in pitch from one

note played on the keyboard to the next one.

Turning Portamento on or off.

While holding down the [SHIFT] button, each

press of the [SUSTAIN] button alternately

selects on or off.

pon

poF

(On) (Off)

Deleting a Phrase

Press the buttons below in order:

[REC]  [/]  [/]

Repeat Playback

Play back the recorded phrase repeatedly.

While holding down [SHIFT], press [/].

NOTE

• You can record the Arpeggio and your performance for

a few measures and then play it back repeatedly, add-

ing your performance along with the playback as

desired.

• From the 2nd repeat playback, the Voice may differ

from the recording Voice. This is because the last

selected Voice during the recording will be used for

from the 2nd playback.

Tempo

You can set the tempo for Phrase, Arpeggio

playback and Motion Effect, Metronome

speed.

Press the [TEMPO/TAP] button.

Use the [+]/[-] buttons while “tEP” or the cur-

rent tempo value is shown.

NOTE

• Holding down the [-] or [+] button continuously

decreases or increases the value.

• To reset the tempo, press the [-] and [+] buttons simul-

taneously.

• While a Phrase or Metronome is playing back, press the

[TEMPO/TAP] button just twice at the desired tempo to

change the tempo.

tEp

Sustain

The notes you play have a longer sustain.

Turning Sustain on or off.

Each press of the [SUSTAIN] button alter-

nately selects on or off.

Son

SoF

(On)

(Off)

PSS-A50 Owner’s Manual

Keyboard Settings

These detailed settings provide extra convenience and enhanced operation. To

change them, hold down the [SHIFT] button, and then simultaneously press the

appropriate key on the keyboard (repeatedly if necessary) as indicated. Use the [+]

and [-] keys to change the value, or the Default key to call up the default value

(indicated with underline).

* Display indications are shown in parentheses.

TRANSPOSE

Changes the pitch of the instrument in semi-

tones, for playing in different keys.

Range: -12 – 00 – 12

TUNING

Finely changes the pitch of the entire instru-

ment in roughly 0.2 Hz steps, for tuning to

other instruments.

Settings: 427.0 – 440.0 – 453.0 Hz (27.0 – 40.0 – 53.0)

Transpose/Tuning

Determines how the sound responds to your

playing strength.

Range: 1 / 2 / 3 / oFF

1: Produces relatively high volume even

with light playing

2: Produces a fairly “standard” keyboard

response.

3: The keys must be played very strongly to

generate loud volume.

oFF: All notes are produced at the same vol-

ume no matter how hard the keyboard is

played.

Touch Response

METRONOME ON/OFF

Sets the Metronome on or off.

Change the speed with the

Tempo control (page 11).

Settings: on / oFF

METRONOME -+ (Beat)

Sets the number of beats (clicks)

in a measure for Metronome and

Phrase (page 10). Set this to 4 for

a 4/4 time signature; or 3 for 3/4.

Settings: 00 – 04 – 16

PHRASE VOLUME

Adjusts the volume of the

Phrase/Metronome sound.

Settings: 00 – 12 – 15

Metronome/Phrase Volume

BATTERY TYPE

Changes the type of battery

to be used. Be sure to

change this to match the

batteries you’ve installed.

Settings: Alkaline/Manganese (AL) or

Rechargeable (n|)

AUTO POWER OFF

Changes the amount of time

that elapses before the

power is automatically

turned off. The Off setting

disables this feature.

Settings: oFF / 005 / 010 / 015 / 030 /

060 / 120 min

Utility

CONTROL CHANGE

Settings: on / oFF (Con / CoF)

PROGRAM CHANGE

Settings: on / oFF (Pon / PoF)

LOCAL CONTROL

Settings: on / oFF (Lon / LoF)

MIDI OUT CHANNEL

Settings: 01–16, oFF

Set as desired when

transmitting/receiving

MIDI data to/from a

computer. For details,

refer to the MIDI Refer-

ence described on

page 6.

MIDI Settings

C2 C3 C4

Default

PSS-A50 Owner’s Manual

Creating Music with MIDI

By connecting this instrument to a computer via

USB cable, you can record performances on this

instrument as a MIDI Song to music production

software on computer, or use this instrument as a

master keyboard to enter data on music produc-

tion software. These features greatly expand your

music creation and performance possibilities. For

details on MIDI, refer to the online PDF manual

“MIDI basics” on the Yamaha website.

Supported OS

• Windows 7, 8.1, 10

• Mac OSX 10.12, 10.13, 10.14

1 Turn off Local Control (page 12; MIDI settings)

as needed.

2 Connect this instrument and the computer with

the USB cable. For connection, see page 6.

NOTE

3 Start recording to the music production soft-

ware and play this instrument.

NOTE

• Windows is a registered trademark of Microsoft

Cor-

poration in the United States and other countries.

• Mac is trademark of Apple Inc., registered in the U.S.

and other countries.

Troubleshooting

Specifications

* The contents of this manual apply to the latest specifications as of the

publishing date. To obtain the latest manual, access the Yamaha

website then download the manual file. Since specifications,

equipment or separately sold accessories may not be the same in

every locale, please check with your Yamaha dealer.

• Be sure to read “Precautions when Using the [5V DC/

USB TO HOST] Terminal” in the MIDI Reference (page 6)

before using the [5V DC/USB TO HOST] terminal.

• When turning Local Control to off, sound will not be

produced from the keyboard.

• If your computer is having difficulty communicating with

the instrument, download the standard Yamaha USB-

MIDI driver from the following web page and install it on

your computer.

http://download.yamaha.com/

• For details on the MIDI transmit channel of the performance

data, refer to the MIDI Reference document (page 6).

• Playing a recorded Phrase will transmit the correspond-

ing MIDI data.

• If the velocity parameter doesn’t reach a value of 127 as

needed, set Touch Response to “1.”

NOTICE

Problem Solution

No sound, too soft

sound or choppy sound

See the text in the

on pages 7 and 9.

Product name Digital keyboard

Keyboard 37 HQ (High Quality) Mini Keys

Touch Response Soft, Medium, Hard, Fixed

Voices

Preset: 40 Voices + 2 Drum Kits

Polyphony (Max.): 32 notes

Octave Button

Yes (-04 – +04)

Arpeggio

138 types

Effects

Motion Effect, Portamento, Sustain

Function

Metronome: Yes, Tempo: 11 – 280,

Transpose: -12 – +12,

Tuning: 427.0 – 440.0 – 453.0 Hz

(approx. 0.2 Hz increments)

Recording

(MIDI data only; audio not

supported.)

• Number of Phrases: 1 (approx. 700

notes; fewer when recording using effects

such as Motion Effect)

Display LED display

Connectivity

Headphones/Output (stereo mini),

5V DC/USB TO HOST (USB micro B)

Amplifiers 1.4 W

Speakers 8 cm x 1

Power Supply

• USB bus power 5V/500mA

• USB power adaptor 5V/500mA

• Four “AA” size alkaline (LR6),

manganese (R6) or Ni-MH

rechargeable (HR6) batteries

Power Consumption 1.5 W

Auto Power Off Yes

Dimensions

(W x D x H)

506 mm x 201 mm x 54 mm

(19-15/16” x 7-15/16” x 2-1/8”)

Weight

1.2 kg (2 lb, 10 oz)

(not including batteries)

Included Accessories

Owner’s Manual, USB cable,

Online Member Product Registration

Separately Sold

Accessories

(May not be available

depending on your area.)

Headphones

(HPH-50/HPH-100/HPH-150)

shaded box

Backup Parameters

The following settings are maintained

even when the power is turned off.

Phrase, Master Volume Level, Tuning,

Touch Response, Battery Type, Auto

Power Off setting, MIDI Settings (other

than Local Control)

When disconnecting the USB power adaptor,

or low (or no) battery power, backup is not exe-

cuted.

Initialization

This operation initializes the

backup data. While holding

down the highest white key

on the keyboard, simultane-

ously press the [ ]

(Standby/On) switch to turn

the power on so that “CLr”

will be displayed.

PSS-A50

Voice List / Voice-Liste / Liste des sonorités / Lista de voces /

Список тембров / /

Voice

No.

MSB

(0-127)

LSB

(0-127)

MIDI Program

Change No.

(1-128)

Voice Name

PIANO

10 0 1 Grand Piano

20 0 5 Electric Piano 1

30 0 6 Electric Piano 2

40 0 3

Electric Grand Piano

ORGAN

5 0 0 17 Drawbar Organ

6 0 0 19 Rock Organ

70 0 22 Accordion

80 0 23 Harmonica

GUITAR

90 0 25 Nylon Guitar

10 0 0 26 Steel Guitar

11 0 0 27 Jazz Guitar

12 0 0 28 Clean Guitar

13 0 0 30 Overdriven Guitar

BASS

14 0 0 33 Acoustic Bass

15 0 0 34 Finger Bass

16 0 0 37 Slap Bass

17 0 0 39 Synth Bass

STRINGS

18 0 0 49 Strings

19 0 0 46 Pizzicato Strings

20 0 0 41 Violin

21 0 0 43 Cello

22 0 0 47 Orchestral Harp

WOODWIND

23 0 0 69 Oboe

24 0 0 72 Clarinet

25 0 0 74 Flute

26 0 0 67 Tenor Sax

BRASS

27 0 0 62 Brass Section

28 0 0 57 Trumpet

29 0 0 58 Trombone

Voice

No.

MSB

(0-127)

LSB

(0-127)

MIDI Program

Change No.

(1-128)

Voice Name

30 0 0 61 French Horn

31 0 0 63 Synth Brass

SYNTH LEAD

32 0 0 83 Gemini

33 0 0 85 Punchy Chordz

34 0 0 81 Square Lead

35 0 0 82 Sawtooth Lead

SYNTH PAD

36 0 0 89 New Age Pad

37 0 0 90 Warm Pad

38 0 0 101 Brightness

DRUM KIT/PERCUSSION

39 127 0 1 Standard Kit

40 127 0 28 Dance Kit

41 0 0 12 Vibraphone

42 0 0 13 Marimba

Voice

No.

MSB

(0-127)

LSB

(0-127)

MIDI Program

Change No.

(1-128)

Voice Name

Maximum Polyphony

The instrument has 32-note maximum polyphony. This means that it can play a maximum of up to 32 notes at once, regardless of what

functions are used. Arpeggio and Phrase playback use a number of the available notes, so when Arpeggio and Phrase playback are used

the total number of available notes for playing on the keyboard is correspondingly reduced. If the maximum polyphony is exceeded, earlier

played notes will be cut off and the most recent notes have priority (last note priority).

NOTE

Maximale Polyphonie

Das Instrument verfügt über eine maximale Polyphonie von 32 Noten. Dies bedeutet, dass das Instrument unabhängig von den aktivierten

Funktionen maximal 32 Noten gleichzeitig spielen kann. Eine bestimmte Anzahl der verfügbaren Noten wird von den Funktionen Arpeggio

und Phrasenwiedergabe belegt; bei deren Einsatz verringert sich somit die Anzahl der für das Spiel auf der Tastatur verfügbaren Noten

entsprechend. Wenn die maximale Polyphonie überschritten wird, werden die am frühesten gespielten Noten ausgeschaltet und die zuletzt

gespielten Noten haben Vorrang (Last Note Priority).

HINWEIS

Polyphonie maximale

L'instrument dispose d'une polyphonie maximale de 32 notes. Cela signifie que l'instrument peut reproduire un nombre maximal de 32 voix

à la fois, indépendamment des fonctions utilisées. L'arpège et le mode de lecture Phrase font appel à un certain nombre de notes

disponibles. Il s'ensuit que lorsque l'arpège et le mode de lecture Phrase sont utilisés, le nombre total de notes disponibles pour

l'interprétation au clavier est réduit en conséquence. Lorsque la polyphonie maximale est dépassée, les notes jouées en premier ne

produisent aucun son et seules les notes interprétées en dernier sont audibles (priorité à la dernière note).

NOTE

• The Voice List includes MIDI program change numbers for each voice. Use these program change numbers when playing the

instrument via MIDI from an external device.

• Program change numbers are often specified as numbers “0–127. ” For these cases, it is necessary to subtract 1 from the intended

program change number to select the appropriate sound, because this list uses a “1–128” numbering system. For example, to select

program change number 39 in the list, transmit program change number 38.

• In der Voice-Liste sind die MIDI-Programmwechselnummern für jede Voice aufgeführt. Verwenden Sie diese

Programmwechselnummern, wenn Sie das Instrument über MIDI von einem externen Gerät aus spielen/ansteuern.

• Die Programmwechselnummern werden häufig als „0–127“ angegeben. Da diese Liste das Nummerierungssystem „1–128“ verwendet,

muss in diesen Fällen von den gesendeten Programmwechselnummern die Zahl 1 abgezogen werden, um den gewünschten Sound zu

erhalten. Wenn Sie z. B. aus der nachstehenden Liste das Programm Nr. 39 auswählen möchten, senden Sie die

Programmwechselnummer 38.

• La liste des voix comporte des numéros de modification de programmes MIDI pour chaque voix. Utilisez ces derniers lorsque vous jouez de

l'instrument via MIDI à partir d'un périphérique externe.

• Les numéros de changement de programme sont souvent spécifiés comme étant de « 0 à 127 ». « Dans ces cas-là, il est nécessaire de soustraire

1 du numéro de changement de programme prévu afin de sélectionner le son approprié, car cette liste utilise un système de numérotation allant

de « 1 à 128 ». Par exemple, pour sélectionner le changement de programme n° 39 dans la liste, il faut transmettre le changement de programme

n° 38.

PSS-A50

Polifonía máxima

El instrumento tiene una polifonía máxima de 32 notas. Esto significa que puede tocar un máximo de 32 notas a la vez,

independientemente de las funciones que se usen. En la reproducción de arpegios y frases se utiliza una parte de las notas disponibles, así

que cuando se utilizan arpegios y frases, el número de notas disponibles se reduce en consecuencia. Si se excede la polifonía máxima, las

notas tocadas con anterioridad se cortan y se da prioridad a las notas más recientes (prioridad de la última nota).

NOTA

Максимальная полифония

Максимальная полифония данного инструмента — 32 ноты. Это значит, что независимо от используемых функций инструмент

может одновременно проигрывать не более 32 нот. Часть нот используется для воспроизведения фраз и арпеджио; таким

образом, при включенном воспроизведении фраз и арпеджио общее количество нот, доступных для игры на клавиатуре,

сокращается. В случае превышения максимальной полифонии ранее сыгранные ноты отсекаются, а ноты, сыгранные

последними, обладают более высоким приоритетом (приоритет последней ноты).

ПРИМЕЧАНИЕ

最大同时发音数

本乐器的最大同时发音数是32个音符。这表示不管使用哪些功能，最多可同时奏出32个音符。琶音和乐

句播放会用到许多可用音符，因此在使用琶音和乐句播放时，能在键盘上演奏的可用音符总数会相应地减

少。如果超过最大同时发音数，先前演奏的音符会被删除掉，最近演奏的音符具有较高优先级（音符越靠

后，优先级越高）。

注

• La lista de voces incluye números de cambio de programa MIDI para cada sonido. Utilice estos números de cambio de programa

cuando toque el instrumento a través del MIDI desde un dispositivo externo.

• Los números de cambio de programa se especifican a menudo como “0 a 127”. En estos casos, se debe restar 1 del número de

cambio de programa deseado para seleccionar el sonido adecuado, porque esta lista utiliza un sistema de numeración de “1 a 128”.

Por ejemplo, para seleccionar el número de cambio de programa 39 en la lista, transmita el número de cambio de programa 38.

• В список тембров включены номера изменения MIDI-программ для каждого тембра. Эти номера используются при воспроизведении

на инструменте с внешнего устройства через интерфейс MIDI.

• Номера изменения программ часто представляются в виде чисел «0–127». В подобных случаях необходимо вычитать 1 из желаемого

номера изменения программы для выбора необходимого звука, поскольку в этом списке используется система нумерации «1–128».

Например, для выбора номера изменения программы 39 в списке передайте номер изменения программы 38.

•

音色一览表包括每种音色的

MIDI

程序变更编号。从外接设备通过

MIDI

使用本乐器进行演奏时，会使用

这些程序变更编号。

•

程序变更编号通常指定为编号

“0-127”

。

127.

因为此一览表使用的是

“1-128”

编号系统，因此需要从所用程序变更编号减去

以选择正确的音色。

例如，若要在列表中选择编号

，则传送程序变更编号

。

Voice List / Voice-Liste / Liste des sonorités / Lista de voces /

Список тембров / 音色一览表 /

PSS-A50

Drum Kit List / Drum Kit-Liste / Liste des kits de batterie / Lista de

juegos de batería / Список наборов ударных / /

Voice No. 39 40

MSB (0–127) / LSB (0–127) / PC (1–128)

127/000/001 127/000/28

Keyboard MIDI

Standard Kit Dance Kit

Note# Note Note# Note

25 C# 013C# -1 Surdo Mute Surdo Mute

26 D 0 14 D -1 Surdo Open Surdo Open

27 D# 015D# -1 Hi Q Hi Q

28 E 0 16 E -1 Whip Slap Whip Slap

29 F 0 17 F -1 Scratch H Scratch H

30 F# 018F# -1 Scratch L Scratch L

31 G 0 19 G -1 Finger Snap Finger Snap

32 G# 020G# -1 Click Noise Click Noise

33 A 0 21 A -1 Metronome Click Metronome Click

34 A# 022A# -1 Metronome Bell Metronome Bell

35 B 0 23 B -1 Seq Click L Seq Click L

36 C 1 24 C 0 Seq Click H Seq Click H

37 C# 125C# 0 Brush Tap Brush Tap

38 D 1 26 D 0 Brush Swirl Brush Swirl

39 D# 127D# 0 Brush Slap Brush Slap

40 E 1 28 E 0 Brush Tap Swirl Reverse Cymbal

41 F 1 29 F 0 Snare Roll Snare Roll

42 F# 130F# 0Castanet Hi Q 2

43 G 1 31 G 0 Snare Soft Snare Techno

44 G# 132G# 0Sticks Sticks

45 A 1 33 A 0 Bass Drum Soft Kick Techno Q

46 A# 134A# 0 Open Rim Shot Rim Gate

47 B 1 35 B 0 Bass Drum Hard Kick Techno L

48 C 2 36 C 1 Bass Drum Kick Techno

49 C# 237C# 1 Side Stick Side Stick Analog

50 D 2 38 D 1 Snare Snare Clap

51 D# 239D# 1 Hand Clap Hand Clap

52 E 2 40 E 1 Snare Tight Snare Dry

53 F 2 41 F 1 Floor Tom L Tom Analog 1

54 F# 242F# 1 Hi-Hat Closed Hi-Hat Close Analog 1

55 G 2 43 G 1 Floor Tom H Tom Analog 2

56 G# 244G# 1 Hi-Hat Pedal Hi-Hat Close Analog 2

57 A 2 45 A 1 Low Tom Tom Analog 3

58 A# 246A# 1 Hi-Hat Open Hi-Hat Open Analog

59 B 2 47 B 1 Mid Tom L Tom Analog 4

60 C 3 48 C 2 Mid Tom H Tom Analog 5

61 C# 349C# 2 Crash Cymbal 1 Cymbal Analog

62 D 3 50 D 2 High Tom Tom Analog 6

63 D# 351D# 2 Ride Cymbal 1 Ride Cymbal 1

64 E 3 52 E 2 Chinese Cymbal Chinese Cymbal

65 F 3 53 F 2 Ride Cymbal Cup Ride Cymbal Cup

66 F# 354F# 2 Tambourine Tambourine

67 G 3 55 G 2 Splash Cymbal Splash Cymbal

68 G# 356G# 2 Cowbell Cowbell Analog

69 A 3 57 A 2 Crash Cymbal 2 Crash Cymbal 2

70 A# 358A# 2 Vibraslap Vibraslap

71 B 3 59 B 2 Ride Cymbal 2 Ride Cymbal 2

72 C 4 60 C 3 Bongo H Bongo H

73 C# 461C# 3 Bongo L Bongo L

74 D 4 62 D 3 Conga H Mute Conga Analog H

75 D# 463D# 3 Conga H Open Conga Analog M

76 E 4 64 E 3 Conga L Conga Analog L

77 F 4 65 F 3 Timbale H Timbale H

78 F# 466F# 3 Timbale L Timbale L

79 G 4 67 G 3 Agogo H Agogo H

80 G# 468G# 3 Agogo L Agogo L

81 A 4 69 A 3 Cabasa Cabasa

82 A# 470A# 3 Maracas Maracas 2

83 B 4 71 B 3 Samba Whistle H Samba Whistle H

84 C 5 72 C 4 Samba Whistle L Samba Whistle L

85 C# 573C# 4 Guiro Short Guiro Short

86 D 5 74 D 4 Guiro Long Guiro Long

87 D# 575D# 4 Claves Claves 2

88 E 5 76 E 4 Wood Block H Wood Block H

89 F 5 77 F 4 Wood Block L Wood Block L

90 F# 578F# 4 Cuica Mute Scratch H

91 G 5 79 G 4 Cuica Open Scratch L

92 G# 580G# 4 Triangle Mute Triangle Mute

93 A 5 81 A 4 Triangle Open Triangle Open

94 A# 582A# 4 Shaker Shaker

95 B 5 83 B 4 Jingle Bells Jingle Bells

96 C 6 84 C 5 Bell Tree Bell Tree

F#2

G#2

A#2

D#2

C#2

F#3

G#3

A#3

D#3

C#3

F#4

G#4

A#4

D#4

C#4

• Each percussion Voice uses one note.

• The MIDI Note No. and Note are actually one octave

lower than keyboard Note No. and Note. For

example, in “Standard Kit,” the “Snare Tight” (Note

No.52/Note E2) corresponds to MIDI (Note No.40/

Note E1).

• Jede Percussion-Voice belegt eine Note.

• Die MIDI-Notennummer und die MIDI-Note sind in

Wirklichkeit eine Oktave tiefer als auf der Tastatur. Z.

B. entspricht im „Standard Kit“ die „Snare Tight“

(Note Nr. 52/Note E2) der MIDI-Notennummer 40

bzw. der Note E1.

• Chaque voix de percussion utilise une note unique.

• Les paramètres MIDI Note No. et Note se situent en

réalité à une octave inférieure à leurs équivalents

Note No. et Note sur le clavier. Par exemple, dans

« Standard Kit », « Snare Tight » (Note No.52/Note

E2) correspond à MIDI (Note No.40/Note E1).

• Cada voz de percusión utiliza una nota.

• El número de nota y la nota MIDI son en realidad

una octava menos que el número de nota y la nota

en el teclado. Por ejemplo, en “Standard Kit”,

“Snare Tight” (nota n.º 52/nota E2) corresponde a

MIDI (nota n.º 40/nota E1).

• В каждом тембре перкуссии используется одна

нота.

• Номер MIDI-ноты и нота в действительности на

одну октаву ниже номера ноты и ноты,

указанных на клавиатуре. Например, в Standard

Kit (стандартный набор) Snare Tight (номер ноты

52 / нота E2) соответствует MIDI (номер ноты 40 /

нота E1).

• 每种打击音色使用一个音符。

•MIDI音符编号和音符比键盘音符编号和

音符实际低一个八度。例如，在音色

“Standard Kit”中， “Snare Tight” （音符

编号52/音符E2）对应于MIDI （音符编

号40/音符E1）。

PSS-A50

Arpeggio List / Liste der Arpeggios / Liste des arpèges / Lista de

arpegios / Список арпеджио / /

NOTE

HINWEIS

NOTE

NOTA

ПРИМЕЧАНИЕ

注

No. Type Name

ACOUSTIC PIANO

1PfArp1

2PfArp2

3PfArp3

4PfArp4

5 PfClub1

6 PfClub2

7 PfBallad

8PfChd8th

9 PfShufle

10 PfRock

11 RocknPf

12 70RockPf

13 SlowflPf

14 SoulPf

15 LatinRck

16 Salsa1

17 Salsa2

18 6/8R&B

KEYBOARD

19 EPArp

20 BalladEP

21 ChordUp

22 ChdDance

23 Clavi1

24 Clavi2

25 Gospel

26 Reggae1

27 Reggae2

28 Reggae3

GUITAR CHORD

29 Strum1

30 Strum2

31 Strum3

32 Strum4

33 Funky

34 GtrChrd1

35 GtrChrd2

36 GtrChrd3

37 CleanGtr

38 Samba1

39 Samba2

40 Spanish1

41 Spanish2

GUITAR ARPEGGIO

42 Pickin1

43 Pickin2

44 GtrArp

45 FngrPck1

46 FngrPck2

47 Slowfl

BASS

48 FngrBas1

49 FngrBas2

50 FngrBas3

51 CoolFunk

52 SlapBass

53 AcidBas1

54 AcidBas2

55 FunkyBas

56 CmbJazB1

57 CmbJazB2

58 CmbJazB3

59 NewR&BBs

60 HipHopBs

61 SmoothBs

62 DreamBas

63 TranceBs

64 LatinBas

STRINGS

65 Strings1

66 Strings2

67 Strings3

68 Strings4

69 StrngDwn

70 StrngUp

71 OrcheStr

72 Jupiter

73 Pizz1

74 Pizz2

HARP

75 Harp1

76 Harp2

BRASS

77 BrasSec1

78 BrasSec2

79 BrasSec3

80 FunkBras

81 SoulReed

CHROMATIC PERC.

82 PercArp

83 Trill

84 Cresendo

85 DiscoCP

SYNTH SEQUENCE

86 UpOct

87 DownOct

88 UpDwnOct

89 SynArp1

90 SynArp2

91 SynArp3

92 SynArp4

No. Type Name

93 SyncEcho

94 PulsLine

95 StepLine

96 Random

97 Down&Up

98 SuperArp

99 AcidLine

100 TekEcho

101 VelGruv

102 Planet

103 Trance1

104 Trance2

105 Trance3

106 DiscoLd

SYNTH CHORD

107 ChordAlt

108 SynChrd1

109 SynChrd2

110 Syncopa

111 Hybrid1

112 Hybrid2

113 Hybrid3

114 Hybrid4

115 Hybrid5

116 SmoothPd

DRUMS

117 Funk1

118 Funk2

119 Funk3

120 Soul

121 ClscHip

122 Smooth

123 NewGospl

124 CmbJazz1

125 Bebop

126 JazzHop

127 FolkRock

128 Unpluggd

129 Dream

130 2 Step

131 ClubHs1

132 ClubHs2

133 House

134 Ibiza2

135 Ibiza3

136 Garage

137 Samba

138 African

No. Typ e Name

• For Nos. 117 – 138, play with

a Drum Kit Voice (No. 39

Standard Kit or No. 40

Dance Kit).

• Bei Nrn. 117–138 spielen Sie

eine Drum-Kit-Voice (Nr. 39

Standard Kit oder Nr. 40

Dance Kit).

• Pour les n° 117 à 138, jouez

une voix de kit de percussion

(Standard Kit n°39 ou Dance

Kit n°40).

• Para los números 117 – 138,

toque con una voz de

conjunto de batería (n.º 39

Standard Kit o n.º 40 Dance

Kit).

• Для номеров 117–138

следует играть с тембром

набора ударных (номер 39 в

Standard Kit (стандартный

набор) номер 40 в Dance Kit

(танцевальная установка)).

•

对于编号

117 – 138

，

与鼓组音色一起演奏

（

Standard Kit

编号

或

Dance Kit

编号

）。

PSS-A50

Motion Effect List / Motion-Effect-Liste / Liste des effets de mouvement /

Lista de efectos de movimiento / Список эффектов движения /

No. Type Na me

A FILTER

A01 Filter 1

A02 FIlter 2

A03 Filter Wah

A04 Filter 3

A05 Filter 4

A06 Filter 5

A07 Filter 6

A08 Filter 7

A09 Filter + Modulation 1

A10 Filter + Modulation 2

B PITCH

B01 Pitch Whole-Note Up

B02 Pitch Half-Note Up

B03 Pitch Whole-Note Down

B04 Pitch Half-Note Down

B05 Choking Up

B06 Choking Down

B07 Pitch Down 1

B08 Pitch Down 2

B09 Pitch Up 1

B10 Pitch Up 2

B11 Pitch Up + Modulation

B12 Pitch Up 3

C MODULATION

C01 Modulation On 1

C02 Modulation On 2

C03 Pitch Up + Modulation On 1

C04 Pitch Up + Modulation On 2

C05 Expression Slice 1

C06 Expression Slice 2

C07 Expression Slice + Filter 1

C08 Expression Slice + Filter 2

C09 Pitch Up + Expression Slice 1

C10 Pitch Up + Expression Slice 2

C11 Pitch Up + Expression Slice 3

C12 Pitch Up + Expression Slice 4

Information for users on collection and disposal of old equipment and used batteries:

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and

batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or

dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU

Battery Directive for the chemical involved.

(weee_battery_eu_en_02)

Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte und benutzter Batterien

Befinden sich diese Symbole auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische

Geräte und Batterien nicht mit dem normalen Haushaltsabfall entsorgt werden.

In Übereinstimmung mit Ihren nationalen Bestimmungen bringen Sie alte Geräte und benutzte Batterien bitte zur fachgerechten

Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte und Batterien helfen Sie, wertvolle Ressourcen zu schützen, und verhindern

mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte

Müllentsorgung auftreten könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte und Batterien kontaktieren Sie bitte Ihre örtliche

Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

Information für geschäftliche Anwender in der Europäischen Union:

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.

Entsorgungsinformation für Länder außerhalb der Europäischen Union:

Diese Symbole gelten nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte

Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.

Anmerkung zum Batteriesymbol (untere zwei Symbolbeispiele):

Dieses Symbol kann auch in Kombination mit einem chemischen Symbol verwendet werden. In diesem Fall entspricht dies den

Anforderungen der EU-Batterierichtlinie zur Verwendung chemischer Stoffe.

(weee_battery_eu_de_02)

Informations concernant la collecte et le traitement des piles usagées et des déchets d’équipements électriques et

électroniques

Les symboles sur les produits, l'emballage et/ou les documents joints signifient que les produits électriques ou électroniques usagés

ainsi que les piles usagées ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques et des piles

usagées, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques et des piles usagées, vous contribuerez

à la sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir

lors d'un traitement inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques et des piles

usagées, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les

produits.

Pour les professionnels dans l'Union européenne :

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques, veuillez contacter votre vendeur ou

fournisseur pour plus d'informations.

Informations sur la mise au rebut dans d'autres pays en dehors de l'Union européenne :

Ces symboles sont seulement valables dans l'Union européenne. Si vous souhaitez vous débarrasser de déchets d’équipements

électriques et électroniques ou de piles usagées, veuillez contacter les autorités locales ou votre fournisseur et demander la

méthode de traitement appropriée.

Note pour le symbole « pile » (deux exemples de symbole ci-dessous) :

Ce symbole peut être utilisé en combinaison avec un symbole chimique. Dans ce cas, il respecte les exigences établies par la

directive européenne relative aux piles pour le produit chimique en question.

(weee_battery_eu_fr_02)

Información para usuarios sobre la recogida y eliminación de los equipos antiguos y las pilas usadas

Estos símbolos en los productos, embalajes y documentos anexos significan que los productos eléctricos y electrónicos y sus pilas

no deben mezclarse con los desperdicios domésticos normales.

Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos y las pilas usadas, llévelos a puntos de reciclaje

correspondientes, de acuerdo con la legislación nacional.

Al deshacerse de estos productos y pilas de forma correcta, ayudará a ahorrar recursos valiosos y a impedir los posibles efectos

desfavorables en la salud humana y en el entorno que de otro modo se producirían si se trataran los desperdicios de modo

inapropiado.

Para obtener más información acerca de la recogida y el reciclaje de los productos antiguos y las pilas, póngase en contacto con las

autoridades locales, con el servicio de eliminación de basuras o con el punto de venta donde adquirió los artículos.

Para los usuarios empresariales de la Unión Europea:

Si desea desechar equipos eléctricos y electrónicos, póngase en contacto con su vendedor o proveedor para obtener más

información.

Información sobre la eliminación en otros países fuera de la Unión Europea:

Estos símbolos solamente son válidos en la Unión Europea. Si desea desechar estos artículos, póngase en contacto con las

autoridades locales o con el vendedor y pregúnteles el método correcto.

Nota sobre el símbolo de pila (dos ejemplos de símbolos en la parte inferior):

Este símbolo se puede utilizar en combinación con un símbolo químico. En este caso, cumple el requisito establecido por la

Directiva de la UE sobre pilas correspondiente a la sustancia química utilizada.

(weee_battery_eu_es_02)

(This product conforms to the RoHS regulations in the EU.)

(Dieses Produkt entspricht der RoHS-Richtlinie der EU.)

(Ce produit est conforme aux réglementations RoHS de l'UE.)

(Este producto cumple con los requisitos de la directiva RoHS en la UE.)

Strona jest ładowana ...

Yamaha PSS-A50 Instrukcja obsługi

Marka: Yamaha

Model: PSS-A50

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

čeština: Yamaha PSS-A50 Návod k obsluze
español: Yamaha PSS-A50 El manual del propietario
italiano: Yamaha PSS-A50 Manuale del proprietario
Deutsch: Yamaha PSS-A50 Bedienungsanleitung
svenska: Yamaha PSS-A50 Bruksanvisning
português: Yamaha PSS-A50 Manual do proprietário
français: Yamaha PSS-A50 Le manuel du propriétaire
Türkçe: Yamaha PSS-A50 El kitabı
English: Yamaha PSS-A50 Owner's manual
dansk: Yamaha PSS-A50 Brugervejledning
русский: Yamaha PSS-A50 Инструкция по применению
suomi: Yamaha PSS-A50 Omistajan opas
Nederlands: Yamaha PSS-A50 de handleiding
română: Yamaha PSS-A50 Manualul proprietarului

Yamaha PSS-A50 Instrukcja obsługi

Yamaha PSS-A50 Instrukcja obsługi

w innych językach

Powiązane dokumenty