AMX Switch RE-DM4 Instrukcja obsługi

Marka: AMX

Model: Switch RE-DM4

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Installation Guide

RE-DM4 Radia Eclipse 4-Channel Dimmer Module (120 or 240 volts)

Overview

The RE-DM4 RADIA Eclipse 4-Channel Integrated Dimmer Module (120 VAC:

FG706-01; 240 VAC: FG706-02) controls up to six circuits with four 1200-watt onboard

dimmers and two satellite connectors for RDM series dimmer or switch modules

(FIG. 1). The RE-DM4 is designed for use with the RDA series of enclosures in an

AMX Lighting™ modular digital dimming system. The RE-DM4 is controlled by AXLink

or by dry (contact) closures.

Specifications

Suggested Loads

Caution: Pre-Installation Notes

WARNING: This unit should be installed only by qualified electrical personnel, and in

compliance with all national electrical codes, local codes and ordinances.To prevent

possible personal injury or death, disconnect power to the enclosure at the breaker

box before attempting to work with any AMX Lighting modules.

• All Class 1 and 2 wiring must be connected to their dedicated terminals.

• Class 1 wiring should be connected through the top of the enclosure, and Class

2 wiring through the bottom.

• Load conductors must be same size as line conductors, regardless of

connected load.

• Disconnect power while installing or connecting the unit.

• Keep top and bottom air vents clear at all times, and maintain 12” (30.48 cm)

clearance around the top and bottom.

• Test loads for shorts before connecting.

• Class 2 wiring must be rated 300V or higher.

• For indoor use only.

• AC lighting loads only.

• This module may require extra power from the AXLink connection or an external

power supply connected to the control card.

• For more information, refer to the RE-DM4 instruction manual available at

www.amx.com.

Radia Lighting System Configuration Pages

The AMX Radia Web pages provide a simple interface for users of the Radia Duet

module. The web pages reside on the AMX master when running the Radia Duet

module and may be accessed through Internet Explorer or Mozilla Firefox. The RE-

DM4 may also be configured using NetLinx code or a terminal. For more information,

refer to the RE-DM4 instruction manual available at www.amx.com.

High-Voltage Connections

Each AMX Lighting module has its high-voltage connectors marked on its circuit

board. Line, load, and neutrals are also clearly marked.

Line-in Connections

• Using two feeds for Line 1 and Line 2 provides two 2400 W inputs.

• With a jumper, Line 1 and Line 2 provides a single 2400 W input (FIG. 3).

FIG. 1 RE-DM4 4-Channel Integrated Dimmer Module

RE-DM4 Specifications

Dimensions (HW) 5.75" x 10.0" (146.05 mm x 254.00 mm)

Weight 4.5 lbs (2.04 kg)

Line Input • 120, 240 VAC, single phase, 2W+G, 50/60 Hz, 2400 W,

one feed

• 120, 120/240, 240 VAC, single phase, 3W+G, 50/60

Hz, 4800 W, dual feed

Output • 1200 W max. per channel @120, 240 VAC

• 2400 W max. total, all four channels on with single

2400 W feed

• 4800 W max. total, all four channels on with dual

2400 W feeds

• Line input #1 goes to dimmer 1 and 3; line input #2

goes to dimmer 2 and 4

• All electrical ratings are for continuous duty

Wire rating Use only copper wires rated at 75°C (167°F) min.

Torque terminals To 20 in-lbs (2.3 N/M)

Maximum wire size 10 AWG (4 mm²)

Wire stripping length 0.5" (13 mm)

AXLink Port 4-pin 3.5mm black captive wire connector. AXLink

communication signaling with 12VDC power in.

Aux Power 2-pin 3.5mm green captive wire connector. This is a

12VDC power input that supplies additional power to the

Radia PCB and connected Radia modules.

Dry Contacts • Emergency fire alarm relay connection - Closed relay

activates preset 126. Other control is locked out until

relay opens. Supports daisy chaining of up to 20

dimmers for this connection, with a maximum current

requirement of 200mA when daisy-chained.

• Failsafe connection - Works with a toggle switch -

opening the switch triggers preset 128, closing the

switch triggers preset 127. Supports daisy chaining of

up to 20 dimmers for this connection with a maximum

current requirement of 200mA when daisy-chained.

BTU/hr 300 single feed (2400 W); 600 dual feed (4800 W)

Mounting

Jumper

Load out

Neutral

Chokes

High

Voltage

Mounting

External +12V

Aux Power

AXLink

DIP Switch

Dry Closures

AXlink Connector

Power Devices

points

Connections

Address

points

4-Pin Connectors

to RDM series

Modules

Line In

Class 1 wiring

Class 2 wiring

RE-DM4 Specifications (Cont.)

Idle current draw 75 mA @ 120 VAC, 50 mA @ 240 VAC, 100 mA @ 13.5

VDC

RDM control current 2 at 200 mA @ 12 VDC with no additional power supply

Certifications • FCC

•CE

• UL North America

• IEC-60950 Safety

Operating Temp Range • 0° to 40°C (32° to 104°F)

Included Accessories • 2 4-pin 3.5mm captive wire connector (41-5047)

• 4 #8-32x1/2” F-point mounting screws

Required Enclosures • RDA-ENC2 (FG606-10)

• RDA-ENC4 (FG606-11)

• RDA-ENC6/6B (FG606-12/13/15)

• RDA-ENC12B (FG606-14/16)

Dimmed Switched

Incandescent Motors

Neon, cold-cathode Fans

FIG. 2

High-voltage connections

FIG. 3 Line-in Connections

Neutral

Line in

Load

Dual 2400 W Inputs without jumper

Single 2400 W Input with jumper

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

8/07

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0706-01 REV: C

Low-Voltage Connections

The low-voltage area in the AMX Lighting controllers contain connections and DIP

switches for AXLink, dry closures, and RDM module connectors. On the controller

cards, low-voltage power for the board is supplied either by line power, optional

auxiliary power supply (RDA-PSM), or the +12 VDC pin on the AXLink connector.

WARNING: Disconnect the main power to the AMX Lighting controller at the

breaker box if rewiring the low voltage connections.

Dry Closure Connections

Dry contact closures from other equipment can be connected to the Radia Eclipse

dimmer module to provide direct manual control of lighting loads (FIG. 5).

Each dry contact closure has two pins: ground and contact. To activate each dry

closure, connect the ground and contact.

Setting AXLink Address Numbers

Set the AXLink address number (1-255) for the RE-DM4. This number must match

the device number in your Axcess program.

Note: By turning all switches off, all circuits will go to 100 percent so that the installer

can test the high-voltage connections without having connections to a control

system.

Connecting AXLink

Connect the 4-pin captive-wire AXLink from the RE-DM4 to the Central Controller for

AXLink control of the dimming system.

RE-DM4 4-pin module connector (male)

Lighting Application Drawings

FIG. 4 Low-voltage connections and DIP switches

FIG. 5 Dry Closure Connections

AXLink address DIP switch

Module connector/LED (CH6)

Dry contact closures

Auxiliary power IN

Module connector/LED (CH5)

AXlink connector

RE-DM4

FAILSAFE

GND

EMERGENCY

GND

Failsafe switch

Alarm system

FIG. 6 Connecting AXlink

FIG. 7 RE-DM4 module connector

Central

RE-DM4

Controller

PWR

AXP

AXM

GND

PWR

AXP

AXM

GND

Pin 4 (GND)

Pin 3 (RLY)

Pin 2 (DIM)

Pin 1 (+12 V)

FIG. 8 Example A

FIG. 9 Example B

Example A

Single input

Single-phase, four load

120 or 240 VAC 1

Example B

Dual Input

Single-phase, four load

120, 120/240, or 240 VAC 1

AMX Switch RE-DM4 Instrukcja obsługi

Marka: AMX

Model: Switch RE-DM4

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

ściągnij PDF

raport

w innych językach

English: AMX Switch RE-DM4 User manual

AMX Switch RE-DM4 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

AMX Switch RE-DM4 Instrukcja obsługi

w innych językach

Inne dokumenty