LIVARNO 303307 Instrukcja obsługi

LED LIGHT STRIP SET

IAN 303307

LED-LICHTLEISTEN-SET

Bedienungs- und Sicherheitshinweise

KOMPLET LISTW

OŚWIETLENIOWYCH LED

Wskazówki dotyczące obsługi i bezpieczeństwa

LED LIGHT STRIP SET

Operation and safety notes

GB Operation and safety notes Page 5

PL Wskazówki dotyczące

obsługi i bezpieczeństwa Strona 18

DE / AT / CH Bedienungs- und

Sicherheitshinweise Seite 32

KOMPLET LISTW

OŚWIETLENIOWYCH LED

Wskazówki dotyczące obsługi i bezpieczeństwa

C

A

1

B

2

D

9

E3 4

5

ca. / approx. / env. 20 cm

G

1

MAX.

3 x

F

6

87

5 GB

List of

pictograms used ...Page 6

Introduction .............Page 6

Intended use .................. Page 6

Description of parts ....... Page 7

Technical details ............Page 7

Included items ...............Page 8

Safety

information ..............Page 8

Safety advice

for installation .......Page 12

Installation ...............Page 13

Mounting the

product on a cupboard ...

Page 13

Mounting the

product on a wall ..........Page 14

Operation .................Page 14

Cleaning

and care .....................Page 14

Disposal ...................... Page 15

Warranty ...................Page 16

6 GB

List of pictograms used

Direct current

Alternating current

Class II product

Independent

control unit

Short-circuit-proof safety

isolating transformer

LED Light Strip Set

Introduction

We congratulate you on the pur-

chase of your new product. You have

chosen a high quality product. The

instructions for use are part of the

product. They contain important in-

formation concerning safety, use and

disposal. Before using the product,

please familiarise yourself with all

of the safety information and instruc-

tions for use. Only use the product

as described and for the speciﬁed

applications. If you pass the product

on to anyone else, please ensure

that you also pass on all the docu-

mentation with it.

Intended use

This product is suitable for use in-

doors. This product is intended for

7 GB

use in private, domestic enviroment

only and not for commercial pur-

poses. Other uses or modiﬁcation

of the product shall be considered

as improper use and could lead to

injury or damage. The manufacturer

accepts no liability for loss or dam-

age arising from improper use.

Description of parts

1 LED lightstrip

2 Connection lead

3 Fastening clip

4 Dowel

5 Screw

6 Connector

7 In-line switch

8 Mains adapter

9 Double-sided adhesive tape

Technical details

LED lightstrip +

Mains adapter:

Total power

consumption: approx. 3 W

LED lightstrip:

Operating

voltage: 12 V 2.3 W

LEDs: 9 x 0.1 W LED

Note: The LEDs

cannot be replaced.

LED lightstrip (Model No.

HG01183A) TÜV SÜD / GS certiﬁed

8 GB

Mains adapter:

Nom. voltage,

primary: 100–240 V∼,

50–60 Hz

Nom. voltage,

secondary: 12 V ,

0.25 A, 3 W

Protection class: II /

Mains adapter

(Model No. YNQST120025VL)

TÜV SÜD / GS certiﬁed

Included items

3 LED Light Strip Sets

1 Mains adapter

3 Connection leads

6 Dowels

6 Fastening clips

6 Screws

6 Double-sided adhesive tapes

1 End cap

1 Operating instructions

Safety

information

DANGER OF

DEATH AND

ACCIDENTS FOR TODDLERS

AND CHILDREN! Never

leave children unsupervised with

the packaging material. The

packaging material represents

a danger of suﬀocation. Children

frequently underestimate the

9 GB

dangers. Please keep children

away from the product at all

times.

This product is not a toy and

should not be played with by

children. Children are not able

to understand the dangers that

can occur when handling this

product.

This product can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental ca-

pabilities or lack of experience

and knowledge if they have be

en

given supervision or instruction

concerning use of the product

in a safe way and understand

the hazards involved. Children

shall not play with the product.

Cleaning and user maintenance

shall not be made by children

without supervision.

Ensure that the product is in-

stalled by suitably experienced

or qualiﬁed persons only.

Check before installation that

the supporting surface is suita-

ble for the fastening clips and

the weight of the product. If

you have any questions about

the product or are unsure about

any of its aspects, please seek

the advice of an electrical

equipment specialist.

Do not pull on the product

lead. Ensure that it is positioned

to avoid creating a trip hazard.

10 GB

The product can be used on all

surfaces oﬃcially classiﬁed as

being of “normal ﬂammability“.

Do not attach any other objects

to the product.

After use store the product in its

original packaging to avoid

causing unintentional damage.

Ensure that the product does

not present a trip hazard.

CAUTION! RISK OF OVER-

HEATING! Do not operate

the product while it is still in the

packaging or rolled up.

This product is only

intended for use

indoors.

Avoid the danger

of death from

electric shock!

Before use, ensure that the mains

voltage available is the same as

the required operating voltage

for the product (100–240 V∼).

Before connecting to the mains,

always check the product for

any damage.

Never use the product if you

ﬁnd damage of any kind.

The connection lead cannot be

repaired! If the connection lead

is damaged, the product must

be taken out of use and dis-

posed of in the proper way.

This product does not contain

any parts which can be serviced

11 GB

by the user. The LEDs cannot

be replaced.

Never open any of the electrical

parts or insert any kind of object

into them.

Protect the product from sharp

edges, mechanical loads and

hot surfaces.

Do not install with sharp fasten-

ers or nails.

Always remove the mains adap-

tor from the socket before install-

ing, dismantling or cleaning.

Never touch the mains adaptor

or the product with moist or wet

hands.

Only connect the lightstrip to

mains adaptor.

Ensure that no more than 3 un

der-

unit lights of the same type are

connected together in series.

Use the product with only the

components described in these

operating instructions.

Disconnect the product from

the mains if you intend not to

use it for an extended period

(e.g. holiday).

LED lightstrip should only be re-

placed with the same type of

lightstrip which is supplied with

this product.

The product is only suited for

use with the included mains

adapter (YNQST120025VL).

Please note that the mains

adaptor continues to draw a

small amount of power even if

the product is turned oﬀ as long

12 GB

as the mains adaptor is plugged

into a power outlet. To switch the

product oﬀ completely, unplug

the mains adaptor from the socket.

The LEDs are not replaceable.

If the LEDs fail at end of their lives,

the product must be replaced.

Safety advice

for installation

The product can be mounted with

the supplied fastening clips on to

all surfaces oﬃcially classiﬁed as

being of “normal ﬂammability”.

CAUTION! RISK OF

ELECTRIC SHOCK! Ensure

that you do not strike any elec-

trical cables, gas or water pipes

in the vicinity of where you are

drilling. If necessary, check the

area using a suitable detector

before you drill.

Before installation, check whether

the substrate is suitable for the

fastening clips and can support

the weight of the product. If you

are unsure about any aspects

of this step, please seek the ad-

vice of an electrical equipment

specialist.

Do not use any sharp and / or

pointed objects, such as wire,

nails or clamps, to fasten the

product in place.

Avoid bending the product.

Otherwise the insulation could

be damaged.

13 GB

Installation

The LED lightstrip 1 can be con-

nected using a connection lead 2

(Fig. B) or without a connection lead

(Fig. C).

Mounting the product

on a cupboard

Note: Thoroughly clean the surface

on to which you intend to install the

product. The surface must be clean,

dry and free of grease. Otherwise

the self-adhesive tape 9 may not

stick properly.

1. Using a pencil, mark the position

on the cupboard, shelf or cabin

et

on to which you intend to attach

the LED lightstrip 1. If neces-

s

ary, use a spirit level as a guide.

2. Stick the double-sided adhesive

tape 9 onto the LED lightstrip

1. Then pull the paper from

the self- adhesive tape 9 on the

back of the LED lightstrip 1.

3. Position the self-adhesive tape

9 on the markings and press

to ﬁx it ﬁrmly into place (Fig. D).

4. Connect the LED lightstrip 1

to the mains adapter 8 (Fig. F)

or connect the LED lightstrip 1

to the connection lead 2 to

connect it to an additional light-

strip (Fig. B).

14 GB

Mounting the

product on a wall

1. Drill the fastening holes (Fig. E).

CAUTION! Ensure that you

do not damage any cables in

the wall.

2. Insert the dowels 4 into the

drilled holes (Fig. E).

3. Fix the fastening clips 3 to the

wall with the screws 5.

4. Connect the LED lightstrip 1

to the mains adapter 8

(Fig.

F

)

or connect the LED lightstrip 1

to the connection lead 2 to

connect it to an additional light-

strip (Fig. B).

Operation

Insert the mains adapter 8 into

the mains socket.

Press the “I” on the in-line switch

7 to switch on the product.

Press the other side of the in-line

switch 7 to switch oﬀ the

product.

Cleaning and care

CAUTION! RISK OF

ELECTRIC SHOCK!

First remove the mains

adaptor from the socket.

15 GB

Do not use any solvents, petrol

or similar items. This would

damage the product.

Only a dry, lint-free cloth should

be used for cleaning.

Disposal

The packaging is made entirely

of recyclable materials, which you

may dispose of at local recycling

facilities.

b

a

Observe the marking of

the packaging materials

for waste separation,

which are marked with abbreviations

(a) and numbers (b) with following

meaning: 1–7: plastics / 20–22:

paper and ﬁbreboard / 80–98:

composite materials.

The product and pack-

aging materials are

recyclable, dispose of it

s

eparately for better waste treatm

ent.

T

he Triman logo is valid in France only.

Contact your local refuse

disposal authority for

more details of how to

dispose of your worn-out product.

To help protect the envi-

ronment, please dispose

of the product properly

when it has reached the end of its

useful life and not in the household

16 GB

waste. Information on collection p

oints

and their opening hours can be ob-

tained from your local authority.

Warranty

The product has been manufactured

to strict quality guidelines and meti-

culously examined before delivery.

In the event of product defects you

have legal rights against the retailer

of this product. Your legal rights are

not limited in any way by our war-

ranty detailed below.

The warranty for this product is 3

years from the date of purchase.

Should this product show any fault

in materials or manufacture within

3 years from the date of purchase,

we will repair or replace it – at our

choice – free of charge to you.

The warranty period begins on the

date of purchase. Please keep the

original sales receipt in a safe loca-

tion. This document is required as

your proof of purchase. This warranty

becomes void if the product has b

een

damaged, or used or maintained

improperly.

The warranty applies to defects in

material or manufacture. This war-

ranty does not cover product parts

subject to normal wear, thus possibly

considered consumables (e.g. bat-

teries) or for damage to fragile

17 GB

parts, e.g. switches, rechargeable

batteries or glass parts.

18 PL

Legenda

zastosowanych

piktogramów...... Strona 19

Wstęp ........................ Strona 19

Zastosowanie zgodne

z przeznaczeniem ...... Strona 20

Opis części ................. Strona 20

Dane techniczne ........ Strona 20

Zawartość ................... Strona 21

Wskazówki

bezpieczeństwa

... Strona 22

Zasady

bezpieczeństwa

podczas

montażu .................. Strona 26

Montaż ..................... Strona 27

Montaż na szafie ....... Strona 27

Montaż na ścianie ..... Strona 28

Zastosowanie ..... Strona 28

Czyszczenie i

pielęgnacja ........... Strona 29

Utylizacja ............... Strona 29

Gwarancja ............ Strona 30

19 PL

Legenda zastosowanych

piktogramów

Prąd stały

Prąd zmienny

Klasa ochrony II

Niezależne

urządzenie sterujące

Odporny na zwarcie

transformator

bezpieczeństwa

Komplet listw

oświetleniowych LED

Wstęp

Gratulujemy Państwu zakupu noweg

o

produktu. Tym samym zdecydowali

się Państwo na zakup produktu wy-

sokiej jakości. Instrukcja obsługi jest

częścią tego produktu. Zawiera ona

w

ażne wskazówki dotyczące bezp

ie-

czeństwa, użytkowania iutylizacji.

Przed pierwszym użyciem produktu

należy zapoznać się ze wszystkimi

wskazówkami dotyczącymi obsługi

ibezpieczeństwa. Używać produktu

wyłącznie zgodnie zjego poniżej

opisanym przeznaczeniem. Wprzy-

padku przekazania produktu innej

osobie należy dołączyć do niego

całą jego dokumentację.

20 PL

Zastosowanie zgod-

ne z przeznaczeniem

Produkt ten jest przeznaczony do

użytku w pomieszczeniach. Produkt

ten przeznaczony jest do zastosowa-

nia jedynie w prywatnych gospodar-

stwach domowych, a nie w celach

k

omercyjnych. Inne zastosowanie lub

zmiany dokonywane w produkcie

uważane są za niezgodne z prze-

znaczeniem i mogą wiązać się z

ryzykiem odniesienia obrażeń i

uszkodzeń produktu. Producent nie

ponosi odpowiedzialności za szkody

powstałe wskutek użycia produktu

niezgodnie z jego przeznaczeniem.

Opis części

1 Listwa oświetleniowa LED

2 Przewόd połączeniowy

3 Klips mocujący

4 Kołek

5 Śruba

6 Złączka

7 Przełącznik wmontowany w

przewód

8 Adapter sieciowy

9 Dwustronna taśma

samoprzylepna

Dane techniczne

Listwa oświetleniowa

LED + zasilacz:

Pobór mocy: ok. 3 W

Strona jest ładowana ...

LIVARNO 303307 Instrukcja obsługi

LIVARNO 303307 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty