Zebra STB3508/3578 instrukcja obsługi

Marka: Zebra

Model: STB3508/3578

Typ: instrukcja obsługi

STB3508/3578 Cradle

Quick Reference Guide

2 STB3508/3578 Cradle

No part of this publication may be reproduced or used in any form, or by any

electrical or mechanical means, without permission in writing from Zebra. This

includes electronic or mechanical means, such as photocopying, recording, or

information storage and retrieval systems. The material in this manual is subject to

change without notice.

The software is provided strictly on an “as is” basis. All software, including firmware,

furnished to the user is on a licensed basis. Zebra grants to the user a

non-transferable and non-exclusive license to use each software or firmware

program delivered hereunder (licensed program). Except as noted below, such

license may not be assigned, sublicensed, or otherwise transferred by the user

without prior written consent of Zebra. No right to copy a licensed program in whole

or in part is granted, except as permitted under copyright law. The user shall not

modify, merge, or incorporate any form or portion of a licensed program with other

program material, create a derivative work from a licensed program, or use a

licensed program in a network without written permission from Zebra. The user

agrees to maintain Zebra’s copyright notice on the licensed programs delivered

hereunder, and to include the same on any authorized copies it makes, in whole or in

part. The user agrees not to decompile, disassemble, decode, or reverse engineer

any licensed program delivered to the user or any portion thereof.

Zebra reserves the right to make changes to any software or product to improve

reliability, function, or design.

Zebra does not assume any product liability arising out of, or in connection with, the

application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise

under any Zebra intellectual property rights. An implied license only exists for

equipment, circuits, and subsystems contained in Zebra products.

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The

Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra

Technologies company.

Zebra Technologies Corporation

Lincolnshire, IL USA

http://www.zebra.com

Warranty

For the complete Zebra hardware product warranty statement, go to:

http://www.zebra.com/warranty.

Quick Reference Guide 3

Introduction

The STB3508/3578 cordless scanner cradle acts as a stand, host communication

interface and charger for the LS3578 cordless scanner. It can sit on a desktop or

be mounted on a wall.

The STB3578 cradle receives data from the scanner via a Bluetooth radio, and

sen

ds that data to the host through an attached cable. The cradle also charges

the scanner’s internal battery pack when the scanner is inserted. The scanner can

be charged from an external power supply or using a powered host cable.

This document provides basic instructions o

n setting up and using the cradle.

Unless otherwise noted, “cradle” refers to both configurations of the cradle. Any

discussion of transmission of information refers specifically to the STB3578

cradle.

CAUTION

LS3478 cordless scanners are incompatible with

STB3508/3578 cradles. LS3578 cordless scanners are incompatible with

TB3408/3478 cradles.

Equipment Supplied

The cradle package includes:

•Cradle

• Four rubber feet (for desk mounting).

Accessories

The following equipment may be needed:

• Three 1.5" #8 Philips head screws (for w

all mounting, if applicable, not

available from Zebra).

• Power supply for desk/wall mounting configuration (p/n 50-14000-266R).

Save the shipping container for storing or

shipping. Inspect all equipment for

damage. If anything is damaged or missing, call an authorized

Zebra business

Support Center immediately.

Related Documentation

LS3578 Product Reference Guide, p/n 72-93911-xx.

LS3578 Quick Start Guide, p/n 72-

93587-xx.

This documentation is available at: http://www.zebra.com/support.

4 STB3508/3578 Cradle

Cradle Parts

Mounting 

Screw Hole

(2)

Charging/

Communication

Contacts

Latch

Pairing

Bar Code

Rubber

Foot

Rubber

Foot

Rubber Feet (2)

Mounting

Screw Hole

Power Cable

Groove

Mounting

Screw Hole

Cable

Hook

Power Port

Host Port

Host Cable

Groove

Mounting

Screw Hole

Converter

Knob

Latch

Back

Front

LED

Quick Reference Guide 5

Cradle Connections

IMPORTANT Connect the interface cable and power supply (if necessary)

in the following order to ensure proper operation of the

scanner and cradle.

1. Insert the interface cable into the cradle’s

host port.

2. Connect the other end of the interface

cable to the host.

3. If necessary, connect the power supply to

the cradle’s power port (if required by the

interface, or to allow fast charging of the

scanner).

4. Connect the appropriate cable to the

power supply and an AC power source, if

necessary.

5. If applicable, thread the interface cable

over the cable support hook and run the

host and power cables into their

respective cable grooves.

6. If necessary, scan the appropriate host

bar code (for non-autodetected

interfaces). Refer to the Product

Reference Guide.

Changing the Host Interface

To connect to a different host, or to the same

host through a different cable:

CAUTION If the scanner does not recognize the host, disconnect the

power supply, then reconnect after connecting the host cable.

1. Unplug the power supply from the cradle.

2. Unplug the interface cable from the host.

3. Connect the interface cable to the new host, or the new interface cable to the

existing host.

4. Reconnect the power supply, if required.

5. If necessary, scan the appropriate host bar code (for non-autodetected

interfaces). Refer to the Product Reference Guide.

Host

Port

Power Port

6 STB3508/3578 Cradle

Mounting the Cradle

Converter Knob:

Horizontal Position

Horizontal Mount

1. Ensure the desk/wall mount

converter knob is in the correct

position, shown at right.

2. If mounting the cradle horizontally

where no fastening is necessary,

peel the protective paper from the

back of the rubber feet included

with the cradle packaging, and

attach the feet to the cradle at the

indentations in the plastic. These feet provide traction and prevent surface

damage.

Vertical Mount

NOTE Do not use the rubber feet when mounting in a vertical orientation.

To mount the cradle on a vertical surface:

1. Use a Philips screwdriver to turn the desk/wall mount converter knob to the position shown

below. The front latches protract to engage the depressions at the base of the scanner’s

handle.

2. Attach the interface and power cables to the appropriate ports (see Cradle

Connections).

3. Press the cables into the cable grooves.

4. Position the cradle on the mounting surface, or use the template included in

this guide.

5. Mark the surface through the three holes on the bottom of the cradle, or use

the mounting template to determine the location of the screw holes.

6. Pre-drill holes to accommodate three 1.5" #8 Philips head screws.

7. Attach the cradle securely to the surface.

8. Place the scanner in the cradle.

Converter Knob

Vertical Position

Quick Reference Guide 7

Inserting the Scanner in the Cradle

To insert the scanner in the cradle:

• Insert the scanner top first. Push the handle until it clicks into p

lace, engaging

the contacts in the cradle and scanner.

Sending Data to the Host Computer

The cradle receives data from the scanner via a wireless radio connection and

transmits it to the host computer via the host cable. The scanner and cradle must

be paired for successful wireless communication.

Pairing

Pairing registers a scanner to the cradle such that the scanner and cradle can

exchange information. The STB3578 operates in two modes: scanner-to-cradle

and multi scanner-to-cradle. In scanner-to-cradle mode, the scanner is paired to

the cradle either by insertion into the cradle (if pairing on insertion is enabled), or

by scanning the pairing bar code. In multi scanner-to-cradle mode, up to three

scanners can be paired to one cradle. A multipoint bar code must be scanned to

activate this feature. Refer to the Product Reference Guide for more information.

The cradle includes pairing bar codes on both it

s front and back. To pair the

scanner with the cradle, scan a pairing bar code. A high-low-high-low beep

sequence followed by a low-high beep sequence indicates successful pairing and

connection to the remote device. A long low, long high beep sequence indicates

unsuccessful pairing. Refer to the Product Reference Guide for more information.

Lost Connection to Host

If scanned data does not transmit to the cradle’s host, ensure that all cables are

firmly inserted and the power supply is connected to an appropriate AC outlet, if

applicable. If scanned data still does not transmit to the host, reestablish a

connection with the host:

1. Disconnect the power supply from the cradle.

2. Disconnect the host interface cable from the cradle.

3. Wait three seconds.

4. Reconnect the host interface cable to the cradle.

5. Reconnect the power supply to the cradle, if required.

8 STB3508/3578 Cradle

6. Reestablish pairing with the cradle by scanning the pairing bar code.

Charging the Scanner Battery in the Cradle

To charge the scanner battery, place the scanner in the cradle (see Inserting the

Scanner in the Cradle). The battery begins charging when t

he scanner LED

indicator starts flashing green. A complete

charge of a fully discharged battery can

take up to four hours using external power and up to 10 hours using the interface

cable.

Scanner LED Indicators

The green LED on the scanner indicates charging activity (see the table below). If

the scanner is charging in fast mode (non-bus powered mode), the green LED

blinks at a fast rate. If the scanner is charging in slow mode (bus-powered mode),

the LED blinks at a slow rate.

If the red LED on the scanner begins flashing

, indicating a charging problem,

remove the scanner from the cradle and replace the battery. If the red LED on the

scanner continues flashing, contact a Zebra business Support Center.

Standard Scanner Use LED Sequences

Off No power applied to scanner (battery is discharged or removed); scanner is

in low power and ready to scan.

Green A bar code was successfully decoded.

Red A data transmission error; scanner malfunction; or, LS3578 cordless

scanner was inserted into an STB3478 cradle.

Charging Use LED Sequences

Green Slow Flash The scanner

charges at the slow rate (used when the cradle is

Green Fast Flash The scanner charges at the fast rate (used when cradle is

powered from an external power supply).

Red Flash Charging problem. Refer to the Product Reference Guide for

more information.

Red and Green

Flash

Temperature fault.

Using a Host Interface to Supply Power

Some hosts can provide power to the cradle via the host interface, instead of an

external power supply.

NOTE The ST

B3578 does not always require a power supply, depending

on the host interface.

Quick Reference Guide 9

Troubleshooting

If the cradle does not work after following the previous procedures:

• Check the system power.

• Check for loose cable connectio

ns.

• Check that the scanner is inserted properly in the cradle.

• Check that the host settings are correct and

the cradle is connected to the

appropriate port on the host.

CAUTION Do not pour, spray, or spill any liquid on the cradle.

Wall Mount Template

Refer to the English version of this guide (p/n 72-93912-xx ) for a wall mount

template.

10 STB3508/3578 Cradle

Health and Safety Recommendations

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the

recommendations below. Consult with your local Health & Safety Manager to ensure that you

are adhering to your company’s safety programs to prevent employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures.

•

Quick Reference Guide 11

Eurasian Customs Union

Евразийский Таможенный Союз

Данный продукт соответствует требованиям знака EAC.

http://www.zebra.com/doc

12 STB3508/3578 Cradle

תומיאת תרהצה

STB3508:

Zebra וילע תולחה תויחנהה לכ תא םאות הז ןקתהש תאזב הריהצמ, 2014/30/EU , 2014/35/EU

ו- 2011/65/EU. אה תבותכב ןימז יפוריאה דוחיאה לש תומיאתה תרהצה לש אלמה טסקטה האבה טנרטני:

www.zebra.com/doc.

STB3578:

Zebra היחנהל םאות הז וידר דויצש תאזב הריהצמ 2011/65/EU ו- 2014/53/EU למה טסקטה . תרהצה לש א

האבה טנרטניאה תבותכב ןימז יפוריאה דוחיאה לש תומיאתה

: www.zebra.com/doc.

Waste Electrical and Electronic Equipment (WEEE)

Български: За клиенти от ЕС: След края на полезния им живот всички продукти трябва

да се връщат на Zebra за рециклиране. За информация относно връщането на продукти,

моля отидете на адрес: http://www.zebra.com/weee.

Ceština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit

spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové

stránce: http://www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er

udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer

zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von

Produkten finden Sie unter http://www.zebra.com/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει

να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την

επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση 

http://www.zebra.com/weee στο ∆ιαδίκτυο.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise

eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun

aadressi: http://www.zebra.com/weee.

English: For EU Customers: All products at the end of their life must be returned to Zebra for

recycling. For information on how to return product, please go to: 

http://www.zebra.com/weee.

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra

al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo

devolver un producto, visite: http://www.zebra.com/weee.

Français: Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être

retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits,

consultez : http://www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita

devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle

modalità di restituzione, visitare il seguente sito Web: 

http://www.zebra.com/weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ

Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu,

skatiet: http://www.zebra.com/weee.

Quick Reference Guide 13

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti

utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:

http://www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell

eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos

tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu

jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott,

jekk jogħġbok żur: http://www.zebra.com/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur

naar Zebra te worden teruggezonden voor recycling. Raadpleeg 

http://www.zebra.com/weee voor meer informatie over het terugzenden van producten.

Polski: klienci z obszaru Unii Europejskiej: produkty wycofane z eksploatacji należy zwrócić

do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajdują się na

stronie internetowej http://www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à

Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite:

http://www.zebra.com/weee.

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare,

trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului,

accesaţi: http://www.zebra.com/weee.

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju

Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: 

http://www.zebra.com/weee.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich

životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov

nájdete na: http://www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi

Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on

osoitteessa http://www.zebra.com/weee.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till

Zebra för återvinning. Information om hur du returnerar produkten finns på 

http://www.zebra.com/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya

iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:

http://www.zebra.com/weee.

Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po isteku vijeka trajanja moraju vratiti

tvrtki Zebra na recikliranje. Informacije o načinu vraćanja proizvoda potražite na web-stranici:

www.zebra.com/weee.



14 STB3508/3578 Cradle

Quick Reference Guide 15

If you have a problem using the equipment, contact your facility’s Technical or

Systems Support. If there is a problem with the equipment, they will contact the

Zebra Support at: http://www.zebra.com/support

For the latest version of this guide go to: http://www.zebra.com/support

Zebra Technologies Corporation

Lincolnshire, IL U.S.A.

http://www.zebra.com



head are trademarks of ZIH Corp, registered in many jurisdictions worldwide. All other

trademarks are the property of their respective owners.

72E-93912-03HE Revision A - October 2017

Service Information

Zebra STB3508/3578 instrukcja obsługi

Marka: Zebra

Model: STB3508/3578

Typ: instrukcja obsługi

ściągnij PDF

raport

w innych językach

English: Zebra STB3508/3578 Reference guide
Nederlands: Zebra STB3508/3578 Referentie gids

Zebra STB3508/3578 instrukcja obsługi

Zebra STB3508/3578 instrukcja obsługi

w innych językach

Powiązane dokumenty