Makita LS1018L Slide Compound Miter Saw Instrukcja obsługi

1

•

GB Slide Compound Miter Saw INSTRUCTION MANUAL

UA Пересувна комбінована пила для

різання під кутом ІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ

PL Ukośnica INSTRUKCJA OBSŁUGI

RO

Ferăstrău glisant pentru tăieri oblice combinate

MANUAL DE INSTRUCŢIUNI

DE Kapp- und Gehrungssäge BEDIENUNGSANLEITUNG

HU Kombinált csúszógérvágó HASZNÁLATI KÉZIKÖNYV

SK

Posuvná pokosová píla na kombinované rezanie

NÁVOD NA OBSLUHU

CZ Radiální pokosová pila NÁVOD K OBSLUZE

LS1018

LS1018L

2

1

11

1

2

1

2

3

4

5

6

1

2

1

3

12

1

2

3

4

1

2

3

4

1 011380 2 011383 3 010230

4 010231 5 010297

6 001538

7 010298 8 001540 9 010233

10 010409 11 011337 12 011336

3

12

3

4

16 010238

12

3

17 010237

1

18 010257

19 010399

1

20 010259

1

2

21 011338

1

22 010477

12

3

45

23 010241

1

23

4

5

24 010242

12

3

4

25 010244

1

2

3

45

6

26 010243

12

3

45

27 010562

1

13 011337

1

2

3

14 011353

1

15 010431

4

1

31 010472

1

2

32 010427

12

3

4

5

33 011346

1

23

34 011343 35 005232

1

36 011378

37 010249

123

38 001555

2

(1)

(2)

(1)

(2) (2)

(1)

(2)

(1)

(2)

(3)(4)

1

39 001557

1

2

3

4

5

40 010404

1

2

3

4

41 010469

1

42 001563

1

2

3

28 011339

12

29 001549

1

2

30 010480

5

1

2

3

46 010253

1

2

47 011413

1

2

48 011379

1

2

3

49 001819

1

2

3

50 011342

12

51 011381

52 007834

1

2

53 010412

43 011411

1

2

3

44 010410

1

2

45 011412

6

ENGLISH

Contents

SPECIFICATIONS........................................................8

General Power Tool Safety Warnings ...........................9

ADDITIONAL SAFETY RULES FOR TOOL..................9

INSTALLATION...........................................................10

FUNCTIONAL DESCRIPTION....................................10

ASSEMBLY ................................................................13

OPERATION...............................................................15

MAINTENANCE .........................................................19

OPTIONAL ACCESSORIES .......................................20

УКРАЇНСЬКА

Зміст

ТЕХНІЧНІ ХАРАКТЕРИСТИКИ .................................22

Застереження стосовно техніки безпеки при роботі з

електроприладами....................................................23

ДОДАТКОВІ ПРАВИЛА БЕЗПЕКИ ПРИ

КОРИСТУВАННІ ІНСТРУМЕНТОМ...........................23

ВСТАНОВЛЕННЯ ......................................................25

ІНСТРУКЦІЯ З ВИКОРИСТАННЯ .............................25

КОМПЛЕКТУВАННЯ..................................................28

ЗАСТОСУВАННЯ.......................................................31

ТЕХНІЧНЕ ОБСЛУГОВУВАННЯ ...............................35

ДОДАТКОВЕ ПРИЛАДДЯ .........................................36

POLSKI

Spis treści

SPECYFIAKCJE.........................................................38

Ogólne zasady bezpieczeństwa obsługi elektronarzędzi

...................................................................................39

DODATKOWE ZASADY BEZPIECZEŃSTWA

DOTYCZĄCE NARZĘDZIA ........................................39

MONTAŻ.....................................................................41

OPIS DZIAŁANIA .......................................................41

MONTAŻ.....................................................................44

DZIAŁANIE.................................................................46

KONSERWACJA ........................................................50

AKCESORIA OPCJONALNE......................................52

ROMÂNĂ

Cuprins

SPECIFICAŢII ............................................................54

Avertismente generale de siguranţă pentru unelte

electrice......................................................................55

NORME SUPLIMENTARE DE SECURITATE PENTRU

MAŞINĂ......................................................................55

INSTALARE................................................................57

DESCRIERE FUNCŢIONALĂ.....................................57

MONTARE..................................................................60

FUNCŢIONARE..........................................................62

ÎNTREŢINERE............................................................66

ACCESORII OPŢIONALE...........................................67

DEUTSCH

Inhalt

TECHNISCHE DATEN ...............................................69

Allgemeine Sicherheitshinweise für Elektrowerkzeuge70

ZUSÄTZLICHE SICHERHEITSREGELN FÜR DAS

WERKZEUG...............................................................70

INSTALLATION ..........................................................72

FUNKTIONSBESCHREIBUNG ..................................72

MONTAGE .................................................................75

ARBEIT ......................................................................78

WARTUNG.................................................................83

SONDERZUBEHÖR...................................................84

MAGYAR

Tartalom

RÉSZLETES LEÍRÁS.................................................86

A szerszámgépekre vonatkozó általános biztonsági

figyelmeztetések.........................................................87

KIEGÉSZÍTŐ BIZTONSÁGI ELŐÍRÁSOK A

SZERSZÁMRA VONATKOZÓAN ...............................87

ÜZEMBEHELYEZÉS ..................................................89

MŰKÖDÉSI LEÍRÁS...................................................89

ÖSSZESZERELÉS.....................................................92

ÜZEMELTETÉS..........................................................94

KARBANTARTÁS.......................................................98

OPCIONÁLIS KIEGÉSZÍTŐK.....................................99

SLOVENSKÝ

Obsah

TECHNICKÉ ÚDAJE ................................................101

Všeobecné bezpečnostné predpisy pre elektronáradie

.................................................................................102

ĎALŠIE BEZPEČNOSNÉ ZÁSADY PRE NÁSTROJ 102

INŠTALÁCIA.............................................................103

POPIS FUNKCIE......................................................104

MONTÁŽ ..................................................................107

PRÁCA.....................................................................109

ÚDRŽBA .................................................................. 113

VOLITEĽNÉ PRÍSLUŠENSTVO............................... 114

ČESKÝ

Obsah

TECHNICKÉ ÚDAJE ................................................ 116

Obecná bezpečnostní upozornění k elektrickému nářadí

................................................................................. 117

DOPLŇKOVÁ BEZPEČNOSTNÍ PRAVIDLA PRO

NÁSTROJ................................................................. 117

INSTALACE.............................................................. 118

POPIS FUNKCE....................................................... 118

MONTÁŽ ..................................................................121

PRÁCE.....................................................................124

ÚDRŽBA ..................................................................127

VOLITELNÉ PŘÍSLUŠENSTVÍ.................................128

7

ENGLISH (Original instructions)

Explanation of general view

1-1. Stopper pin

2-1. Bolts

3-1. Blade guard

4-1. Blade guard

5-1. Screw

5-2. Kerf board

6-1. Saw blade

6-2. Blade teeth

6-3. Kerf board

6-4. Left bevel cut

6-5. Straight cut

6-6. Right bevel cut

7-1. Adjusting bolt

7-2. Turn base

8-1. Top surface of turn base

8-2. Periphery of blade

8-3. Guide fence

9-1. Stopper arm

9-2. Adjusting screw

10-1. Miter scale

10-2. Pointer

10-3. Lock lever

10-4. Grip

11-1. Lever

12-1. Lever

12-2. Arm

12-3. Pointer

12-4. Bevel scale

13-1. Lever

14-1. Pointer

14-2. Release button

14-3. Bevel scale

15-1. Locking screw

16-1. Lock-off button

16-2. Switch trigger

16-3. Lever

16-4. Hole for padlock

17-1. Lock-off button

17-2. Switch trigger

17-3. Hole for padlock

18-1. Switch for laser

20-1. Dry cell

21-1. Socket wrench with hex wrench on

its other end

21-2. Wrench holder

22-1. Stopper pin

23-1. Socket wrench

23-2. Blade case

23-3. Center cover

23-4. Hex bolt

23-5. Blade guard

24-1. Blade case

24-2. Socket wrench

24-3. Hex bolt

24-4. Arrow

24-5. Shaft lock

25-1. Blade case

25-2. Arrow

25-3. Arrow

25-4. Saw blade

26-1. Hex bolt (left-handed)

26-2. Outer flange

26-3. Saw blade

26-4. Ring

26-5. Inner flange

26-6. Spindle

27-1. Socket wrench

27-2. Blade case

27-3. Center cover

27-4. Hex bolt

27-5. Blade guard

28-1. Dust nozzle

28-2. Dust bag

28-3. Fastener

29-1. Support

29-2. Turn base

30-1. Sliding fence

30-2. Clamping screw

31-1. Sliding fence

32-1. Sub-fence R

32-2. Screws

33-1. Vise arm

33-2. Vise knob

33-3. Vise rod

33-4. Screw

33-5. Guide fence

34-1. Vise plate

34-2. Vise nut

34-3. Vise knob

36-1. Holder

38-1. 52/38 ﾟ type crown molding

38-2. 45 ﾟ type crown molding

38-3. 45 ﾟ type cove molding

39-1. Inside corner

39-2. Outside corner

40-1. Guide fence

40-2. Vise

40-3. Spacer block

40-4. Aluminum extrusion

40-5. Spacer block

41-1. Aluminum extrusion

41-2. Guide fence

41-3. Spacer block

41-4. Horizontal vise (optional

accessory)

42-1. Cut grooves with blade

44-1. Hex bolt

44-2. Guide fence

44-3. Grip

45-1. Guide fence

45-2. Triangular rule

46-1. Screw

46-2. Pointer

46-3. Miter scale

47-1. Lever

47-2. Arm

48-1. 0 ﾟ adjusting bolt

48-2. Left 45 ﾟ bevel angle adjusting bolt

49-1. Triangular rule

49-2. Saw blade

49-3. Top surface of turn table

50-1. Screw

50-2. Pointer

50-3. Bevel scale

51-1. Right 45 ﾟ bevel angle adjusting

bolt

51-2. Left 45 ﾟ bevel angle adjusting bolt

53-1. Screwdriver

53-2. Brush holder cap

8

SPECIFICATIONS

Model LS1018 / LS1018L

Blade diameter 255 mm - 260 mm

Blade body thickness 1.6 mm - 2.4 mm

Hole diameter

For all countries other than European countries 25.4 mm

For European countries 30 mm

Max. Cutting capacities (H x W) with 260 mm in diameter

Bevel angle

Miter angle 45° (left) 0° 45° (right)

0° 50 mm x 310 mm 91 mm x 310 mm 31 mm x 310 mm

45° 50 mm x 220 mm 91 mm x 220 mm 31 mm x 220 mm

60° (right) - 91 mm x 153 mm -

No load speed (min-1) 4,300

Laser Type (LS1018L only) Red Laser 650 nm, 1mW ( Laser Class 2 )

Dimensions (L x W x H) 825 mm x 536 mm x 633 mm

Net weight For all countries other than European countries………19.8 kg

For European countries…………………………………….…19.9 kg

Safety class /II

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

END222-1

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ To avoid injury from flying debris, keep

holding the saw head down, after

making cuts, until the blade has come to

a complete stop.

･ When performing slide cut, first pull

carriage fully and press down handle,

then push carriage toward the guide

fence.

･ Do not place hand or fingers close to the

blade.

･ Adjust sliding fences clear of blade and

blade guard properly.

･ Always remove SUB-FENCE R when

performing right bevel cuts. Failure to do

so may cause serious injury to operator.

･ Never look into the laser beam. Direct

laser beam may injure your eyes.

･ Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of European Directive

2002/96/EC on waste electric and

electronic equipment and its

implementation in accordance with

national law, electric equipment that

have reached the end of their life must

be collected separately and returned to

an environmentally compatible recycling

facility.

ENE006-1

Intended use

The tool is intended for accurate straight and miter

cutting in wood. With appropriate saw blades, aluminum

can also be sawed.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN61029:

Sound pressure level (LpA) : 97 dB(A)

Sound power level (LWA) : 103 dB(A)

Uncertainty (K) : 3 dB(A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN61029:

9

Vibration emission (ah) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test

method and may be used for comparing one tool

with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission

value depending on the ways in which the tool is

used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).

ENH003-13

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Slide Compound Miter Saw

Model No./ Type: LS1018, LS1018L

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN61029

The technical documentation is kept by our authorised

representative in Europe who is:

Makita International Europe Ltd.

Michigan Drive, Tongwell,

Milton Keynes, Bucks MK15 8JD, England

6.11.2009

000230

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

GEA010-1

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for

future reference.

ENB034-6

ADDITIONAL SAFETY RULES

FOR TOOL

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard

does not move freely and close instantly.

Never clamp or tie the blade guard into the

open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6.

Turn off tool and wait for saw blade to stop

before moving workpiece or changing

settings.

7. Unplug tool before changing blade or

servicing.

8. Always secure all moving portions before

carrying the tool.

9. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

10.

Do not use the tool in the presence of

flammable liquids or gases.

The electrical

operation of the tool could create an explosion and

fire when exposed to flammable liquids or gases.

11. Check the blade carefully for cracks or

damage before operation.

Replace cracked or damaged blade

immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt.

Damage to these parts could result in blade

breakage.

14. Make sure that the turn base is properly

secured so it will not move during operation.

15.

For your safety, remove the chips, small

pieces, etc. from the table top before

10

operation.

16. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

17. Make sure the shaft lock is released before the

switch is turned on.

18. Be sure that the blade does not contact the

turn base in the lowest position.

19. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

20. Make sure the blade is not contacting the

workpiece before the switch is turned on.

21. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced blade.

22. Wait until the blade attains full speed before

cutting.

23. Stop operation immediately if you notice

anything abnormal.

24. Do not attempt to lock the trigger in the on

position.

25. Be alert at all times, especially during

repetitive, monotonous operations. Do not be

lulled into a false sense of security. Blades are

extremely unforgiving.

26. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

27. Do not use the saw to cut other than wood,

aluminum or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

29. Select saw blades in relation to the material to

be cut.

30. Take care when slotting.

31. Replace the kerf board when worn.

32. Do not use saw blades manufactured from

high speed steel.

33. Some dust created from operation contains

chemicals known to cause cancer, birth

defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based-painted material and,

•

arsenic and chromium from

chemically-treated lumber.

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area

and work with approved safety equipment,

such as those dust masks that are

specially designed to filter out

microscopic particles.

34. To reduce the emitted noise, always be sure

that the blade is sharp and clean.

35. The operator is adequately trained in the use,

adjustment and operation of the machine.

36. Use correctly sharpened saw blades. Observe

the maximum speed marked on the saw blade.

37. Refrain from removing any cut-offs or other

parts of the workpiece from the cutting area

whilst the tool is running and the saw head is

not in the rest position.

38. Use only saw blades recommended by the

manufacturer which conform to EN847-1.

39. Wear gloves for handling saw blade (saw

blades shall be carried in a holder wherever

practicable) and rough material.

40. When fitted with laser, no exchange with

different type of laser is permitted. Repairs

shall only be carried out correctly.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Bench mounting

Fig.1

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. Release the stopper

pin by simultaneously applying a slight downward

pressure on the handle and pulling the stopper pin.

Fig.2

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool's

base. This will help prevent tipping and possible injury.

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking

function on the tool. Failure to switch off and

unplug the tool may result in serious personal injury

from accidental start-up.

Blade guard

Fig.3

When lowering the handle, the blade guard rises

automatically. The blade guard returns to its original

position when the cut is completed and the handle is

raised.

WARNING:

• Never defeat or remove the blade guard or the

spring which attaches to the guard. An exposed

blade as a result of defeated guarding may result in

serious personal injury during operation.

In the interest of your personal safety, always maintain

the blade guard in good condition. Any irregular

operation of the blade guard should be corrected

11

immediately. Check to assure spring loaded return action

of guard.

WARNING:

• Never use the tool if the blade guard or spring

are damaged, faulty or removed. Operation of

the tool with a damaged, faulty or removed guard

may result in serious personal injury.

If the see-through blade guard becomes dirty, or

sawdust adheres to it in such a way that the blade

and/or workpiece is no longer easily visible, unplug the

saw and clean the guard carefully with a damp cloth. Do

not use solvents or any petroleum-based cleaners on

the plastic guard because this may cause damage to

the guard.

If the blade guard becomes dirty and needs to be

cleaned for proper operation follow the steps below:

With the tool switched off and unplugged, use the

supplied socket wrench to loosen the hex bolt holding the

center cover. Loosen the hex bolt by turning it

counterclockwise and raise the blade guard and center

cover.

Fig.4

With the blade guard so positioned, cleaning can be

more completely and efficiently accomplished. When

cleaning is complete reverse procedure above and

secure bolt. Do not remove spring holding blade guard.

If guard becomes damaged through age or UV light

exposure, contact a Makita service center for a new

guard.

DO NOT DEFEAT OR REMOVE GUARD.

Positioning kerf board

Fig.5

Fig.6

This tool is provided with the kerf boards in the turn base

to minimize tearing on the exit side of a cut. The kerf

boards are factory adjusted so that the saw blade does

not contact the kerf boards. Before use, adjust the kerf

boards as follows:

First, unplug the tool. Loosen all the screws (3 each on

left and right) securing the kerf boards. Re-tighten them

only to the extent that the kerf boards can still be easily

moved by hand. Lower the handle fully and push in the

stopper pin to lock the handle in the lowered position.

Loosen the screw which secures the slide poles. Pull

the carriage toward you fully. Adjust the kerf boards so

that the kerf boards just contact the sides of the blade

teeth. Tighten the front screws (do not tighten firmly).

Push the carriage toward the guide fence fully and

adjust the kerf boards so that the kerf boards just

contact the sides of blade teeth. Tighten the rear screws

(do not tighten firmly).

After adjusting the kerf boards, release the stopper pin

and raise the handle. Then tighten all the screws

securely.

NOTICE:

• After setting the bevel angle ensure that the

kerf boards are adjusted properly. Correct

adjustment of the kerf boards will help provide

proper support of the workpiece minimizing

workpiece tear out.

Maintaining maximum cutting capacity

This tool is factory adjusted to provide the maximum

cutting capacity for a 255 mm saw blade.

Unplug the tool before any adjustment is attempted.

When installing a new blade, always check the lower

limit position of the blade and if necessary, adjust it as

follows:

Fig.7

Fig.8

First, unplug the tool. Push the carriage toward the guide

fence fully and lower the handle completely. Use the hex.

wrench to turn the adjusting bolt until the periphery of the

blade extends slightly below the top surface of the turn

base at the point where the front face of the guide fence

meets the top surface of the turn base.

With the tool unplugged, rotate the blade by hand while

holding the handle all the way down to be sure that the

blade does not contact any part of the lower base.

Re-adjust slightly, if necessary.

WARNING:

• After installing a new blade and with the tool

unplugged, always be sure that the blade does

not contact any part of the lower base when the

handle is lowered completely. If a blade makes

contact with the base it may cause kickback and

result in serious personal injury.

Stopper arm

Fig.9

The lower limit position of the blade can be easily

adjusted with the stopper arm. To adjust it, move the

stopper arm in the direction of the arrow as shown in the

figure. Adjust the adjusting screw so that the blade stops

at the desired position when lowering the handle fully.

Adjusting the miter angle

Fig.10

Loosen the grip by turning counterclockwise. Turn the

turn base while pressing down the lock lever. When you

have moved the grip to the position where the pointer

points to the desired angle on the miter scale, securely

tighten the grip clockwise.

CAUTION:

• After changing the miter angle, always secure the

turn base by tightening the grip firmly.

NOTICE:

• When turning the turn base, be sure to raise the

handle fully.

12

Adjusting the bevel angle

Fig.11

To adjust the bevel angle, loosen the lever at the rear of

the tool counterclockwise. Unlock the arm by pushing the

handle somewhat strongly in the direction that you intend

to tilt the saw blade.

NOTE:

• Lever can be adjusted to a different lever angle by

removing the screw holding the lever and securing

the lever at a desired angle.

Fig.12

Tilt the saw blade until the pointer points to the desired

angle on the bevel scale. Then tighten the lever

clockwise firmly to secure the arm.

Fig.13

When tilting the carriage to the right, tilt the carriage to

the left slightly after loosening the lever and press the

releasing button. With the releasing button being pressed,

tilt the carriage to the right.

Fig.14

Tilt the saw blade until the pointer points to the desired

angle on the bevel scale. Then tighten the lever

clockwise firmly to secure the arm.

• When changing bevel angles, be sure to position

the kerf boards appropriately as explained in the

"Positioning kerf boards" section.

CAUTION:

• After changing the bevel angle, always secure the

arm by tightening the lever clockwise.

NOTICE:

• When tilting the saw blade be sure the handle is

fully raised.

• When changing bevel angles, be sure to position

the kerf boards appropriately as explained in the

"Positioning kerf boards" section.

Slide lock adjustment

Fig.15

To lock the slide pole, turn the locking screw clockwise.

Switch action

For European countries

Fig.16

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

push the lever to the left, press in the lock-off button and

then pull the switch trigger. Release the switch trigger to

stop.

WARNING:

• Before plugging in the tool, always check to

see that the switch trigger actuates properly

and returns to the "OFF" position when

released. Do not pull the switch trigger hard

without pressing in the lock-off button. This

can cause switch breakage. Operating a tool with

a switch that does not actuate properly can lead to

loss of control and serious personal injury.

A hole is provided in the switch trigger for insertion of

padlock to lock the tool off.

For all countries other than European countries

Fig.17

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

WARNING:

• Before plugging in the tool, always check to

see that the switch trigger actuates properly

and returns to the "OFF" position when

released. Do not pull the switch trigger hard

without pressing in the lock-off button. This

can cause switch breakage. Operating a tool with

a switch that does not actuate properly can lead to

loss of control and serious personal injury.

A hole is provided in the switch trigger for insertion of

padlock to lock the tool off.

WARNING:

• Do not use a lock with a shank or cable any

smaller than 6.35 mm in diameter. A smaller

shank or cable may not properly lock the tool in the

off position and unintentional operation may occur

resulting in serious personal injury.

• NEVER use tool without a fully operative

switch trigger. Any tool with an inoperative switch

is HIGHLY DANGEROUS and must be repaired

before further usage or serious personal injury may

occur.

• For your safety, this tool is equipped with a lock-off

button which prevents the tool from unintended

starting. NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the

lock-off button. A switch in need of repair may result

in unintentional operation and serious personal

injury. Return tool to a Makita service center for

proper repairs BEFORE further usage.

• NEVER defeat the lock-off button by taping down or

some other means. A switch with a defeated

lock-off button may result in unintentional operation

and serious personal injury.

Electronic function

Soft start feature

• This function allows the smooth start-up of the tool

by limiting the start-up torque.

13

Laser beam action

For model LS1018L only

NOTE:

• Before the first use, install two AA dry cells in the

cell box. Refer to the section titled "Replacing the

dry cells for laser unit" for the installment.

CAUTION:

• When not in use, be sure to turn off the laser

Fig.18

CAUTION:

• Never look into the laser beam. Direct laser beam

may injure your eyes.

• LASER RADIATION, DO NOT STARE INTO THE

BEAM, CLASS 2 LASER PRODUCT.

•

Before shifting the laser line or performing

maintenance adjustment, be sure to unplug the

tool.

To turn on the laser beam, press the upper position (I) of

the switch. To turn off the laser beam, press the lower

position (0) of the switch.

Laser line can be shifted to either the left or right side of

the saw blade by loosening the screw holding the laser

unit box and shifting it in the desired direction. After

shifting, be sure to tighten the screw.

1

010473

Laser line is factory adjusted so that it is positioned within

1 mm from the side surface of the blade (cutting

position).

NOTE:

• When laser line appears dim and hard to see

because of direct sunlight, relocate the work area to

a place where there is less direct sunlight.

Replacing the dry cells for laser unit

Fig.19

Fig.20

Remove the lid for the dry cells for laser unit by sliding

while pressing it. Take out the old dry cells and put the

new ones as shown in the figure. After replacing, return

the lid to cover it.

Cleaning of the lens for the laser light

If the lens for the laser light becomes dirty, or sawdust

adheres to it in such a way that the laser line is no longer

easily visible, unplug the saw and remove and clean the

lens for the laser light carefully with a damp, soft cloth.

Do not use solvents or any petroleum-based cleaners on

the lens.

NOTE:

• When laser line is dim and almost or entirely

invisible because of the direct sunlight in the indoor

or outdoor window-by work, relocate the work area

to a place not exposed to the direct sunlight.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

unplugged before working on the tool. Failure to

switch off and unplug the tool may result in serious

personal injury.

Storage of socket wrench with hex wrench on

its other end

Fig.21

The socket wrench is stored as shown in the figure.

When the socket wrench is needed it can be pulled out of

the wrench holder. After using the socket wrench it can

be stored by returning it to the wrench holder.

Installing or removing saw blade

WARNING:

• Always be sure that the tool is switched off and

unplugged before installing or removing the

blade. Accidental start up of the tool may result in

serious personal injury.

• Use only the Makita socket wrench provided to

install or remove the blade.Failure to use the

wrench may result in overtightening or insufficient

tightening of the hex bolt and serious personal

injury.

Fig.22

Lock the handle in the raised position by pushing in the

stopper pin.

Fig.23

To remove the blade, use the socket wrench to loosen

the hex bolt holding the center cover by turning it

counterclockwise. Raise the blade guard and center

cover.

Fig.24

Press the shaft lock to lock the spindle and use the

socket wrench to loosen the hex bolt clockwise. Then

remove the hex bolt, outer flange and blade.

1. Screw holding the laser unit box

14

NOTE:

• If the inner flange is removed be sure to install it on

the spindle with its protrusion facing away from the

blade. If the flange is installed incorrectly the

flange will rub against the machine.

WARNING:

• Before mounting the blade onto the spindle,

always be sure that the correct ring for the

blade's arbor hole you intend to use is installed

between the inner and the outer flanges. Use of

the incorrect arbor hole ring may result in the

improper mounting of the blade causing blade

movement and severe vibration resulting in

possible loss of control during operation and in

serious personal injury.

Fig.25

To install the blade, mount it carefully onto the spindle,

making sure that the direction of the arrow on the surface

of the blade matches the direction of the arrow on the

blade case.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt (left-handed)

securely counterclockwise while pressing the shaft lock.

For all countries other than European countries

Fig.26

WARNING:

•

The black ring 25 mm in outer diameter and the

silver ring 25.4 mm in outer diameter are

factory-installed as shown in the figure. When

using a blade with 25 mm hole diameter, replace

the silver ring with the black ring.

Before

mounting the blade onto the spindle, always

be sure that the correct ring for the blade's

arbor hole you intend to use is installed

between the inner and the outer flanges.

Use of

the incorrect arbor hole ring may result in the

improper mounting of the blade causing blade

movement and severe vibration resulting in

possible loss of control during operation and in

serious personal injury.

For European countries

CAUTION:

•

The ring 30 mm in outer diameter is factory-installed

between the inner and outer flanges.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt securely

counterclockwise while pressing the shaft lock.

Fig.27

Return the blade guard and center cover to its original

position. Then tighten the hex bolt clockwise to secure the

center cover. Release the handle from the raised position

by pulling the stopper pin. Lower the handle to make sure

that the blade guard moves properly. Make sure the shaft

lock has released spindle before making cut.

Dust bag (accessory)

Fig.28

The use of the dust bag makes cutting operations

cleaner and dust collection easier. To attach the dust bag,

fit it onto the dust nozzle.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust

bag of its contents, tapping it lightly so as to remove

particles adhering to the insides which might hamper

further collection.

NOTE:

If you connect a vacuum cleaner to your saw, cleaner

operations can be performed.

Securing workpiece

WARNING:

• It is extremely important to always secure the

workpiece correctly with the proper type of

vise or crown molding stoppers. Failure to do so

may result in serious personal injury and cause

damage to the tool and/or the workpiece.

• After a cutting operation do not raise the blade

until it has come to a complete stop. The raising

of a coasting blade may result in serious personal

injury and damage to the workpiece.

•

When cutting a workpiece that is longer than

the support base of the saw, the material

should be supported the entire length beyond

the support base and at the same height to

keep the material level.

Proper workpiece

support will help avoid blade pinch and possible

kickback which may result in serious personal

injury. Do not rely solely on the vertical vise and/or

horizontal vise to secure the workpiece. Thin

material tends to sag. Support workpiece over its

entire length to avoid blade pinch and possible

KICKBACK.

Fig.29

Guide fence (SLIDING FENCES which are

upper and lower fences) adjustment

Fig.30

WARNING:

• Before operating the tool, make sure that the sliding

fence is secured firmly.

• Before bevel-cutting, make sure that no part of

the tool, especially the blade, contacts the

upper and lower fences when fully lowering

and raising the handle in any position and

while moving the carriage through its full range

of travel. If the tool or blade makes contact with the

fence this may result in kickback or unexpected

movement of the material and serious personal

injury.

15

Fig.31

CAUTION:

•

When performing bevel cuts, slide the sliding

fence to the left and secure it as shown in the

figure. Otherwise, it will contact the blade or a part

of the tool, causing possible serious injury to the

operator.

This tool is equipped with the sliding fence which should

ordinarily be positioned as shown in the figure.

However, when performing left bevel cuts, set it to the left

position as shown in the figure if the tool head contacts it.

When bevel-cutting operations are complete, don't forget

to return the sliding fence to the original position and

secure it by firmly tightening the clamping screw.

Sub-fence R

WARNING:

• Before operating the tool, make sure that the

sub-fence R is secured firmly.

•

Before performing right bevel cuts, remove the

sub-fence R. It will contact the blade or a part of

the tool, causing possible serious injury to the

operator.

Fig.32

The sub-fence R can be removed from the right side of

the guide fence. To remove the sub-fence R, loosen the

screw which secures the sub-fence R and pull it out.

Follow the removal procedure in reverse to install it.

When bevel-cutting operations are complete, don't forget

to return the sub-fence R to the original position and

secure it by firmly tightening the clamping screw.

Vertical vise

Fig.33

The vertical vise can be installed on either the left or right

side of the guide fence. Insert the vise rod into the hole in

the guide fence and tighten the screw on the back of the

guide fence to secure the vise rod.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the screw to secure the vise arm

contacts the guide fence, install the screw on the

opposite side of vise arm. Make sure that no part of the

tool contacts the vise when lowering the handle fully and

pulling or pushing the carriage all the way. If some part

contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

WARNING:

• The workpiece must be secured firmly against

the turn base and guide fence with the vise

during all operations. If the workpiece is not

properly secured against the fence the material

may move during the cutting operation causing

possible damage to the blade, causing the material

to be thrown and loss of control resulting in serious

personal injury.

Horizontal vise (optional accessory)

Fig.34

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

10° or greater miter cuts, install the horizontal vise on the

side opposite the direction in which the turn base is to be

turned.

Fig.35

By flipping the vise nut counterclockwise, the vise is

released, and rapidly moves in and out. To grip the

workpiece, push the vise knob forward until the vise plate

contacts the workpiece and flip the vise nut clockwise.

Then turn the vise knob clockwise to secure the

workpiece.

The maximum width of workpiece which can be secured

by the horizontal vise is 215 mm.

When installing the horizontal vise on the right side of the

base, also use the sub-fence R to secure the workpiece

more firmly. Refer to the "Sub-fence R" section described

on previously for installing the sub-fence R.

WARNING:

•

Always rotate the vise nut clockwise until the

workpiece is properly secured.

If the workpiece

is not properly secured the material may move

during the cutting operation causing possible

damage to the blade, causing the material to be

thrown and loss of control resulting in serious

personal injury.

•

When cutting a thin workpiece, such as base

boards, against the fence, always use the

horizontal vise.

Holders

Fig.36

The holders can be installed on either side as a

convenient means of holding workpieces horizontally.

Slip fully the holder rods into the holes in the base. Then

tighten the holders securely with the screws.

WARNING:

• Always support a long workpiece so it is level

with the top surface of the turn base for an

accurate cut and to prevent dangerous loss of

tool control. Proper workpiece support will help

avoid blade pinch and possible kickback which may

result in serious personal injury.

OPERATION

NOTICE:

• Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

• Do not apply excessive pressure on the handle

when cutting. Too much force may result in

overload of the motor and/or decreased cutting

16

efficiency. Push down handle with only as much

force as is necessary for smooth cutting and

without significant decrease in blade speed.

• Gently press down the handle to perform the cut. If

the handle is pressed down with force or if lateral

force is applied, the blade will vibrate and leave a

mark (saw mark) in the workpiece and the precision

of the cut will be impaired.

• During a slide cut, gently push the carriage toward

the guide fence without stopping. If the carriage

movement is stopped during the cut, a mark will be

left in the workpiece and the precision of the cut will

be impaired.

WARNING:

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

Turning the tool on with the blade in contact with the

workpiece may result in kickback and serious

personal injury.

1. Press cutting (cutting small workpieces)

1

011409

Workpieces up to 91 mm high and 70 mm wide can

be cut in the following manner.

Push the carriage toward the guide fence fully and

tighten the locking screw clockwise to secure the

carriage. Secure the workpiece correctly with the

proper type of vise. Switch on the tool without the

blade making any contact and wait until the blade

attains full speed before lowering. Then gently

lower the handle to the fully lowered position to cut

the workpiece. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS

COME TO A COMPLETE STOP before returning

the blade to its fully elevated position.

WARNING:

• Firmly tighten the knob clockwise so that the

carriage will not move during operation.

Insufficient tightening of the knob may cause

possible kickback which may result in serious

personal injury.

2. Slide (push) cutting (cutting wide workpieces)

1

011410

Loosen the locking screw counterclockwise so that

the carriage can slide freely. Secure the workpiece

with the proper type of vise. Pull the carriage

toward you fully. Switch on the tool without the

blade making any contact and wait until the blade

attains full speed. Press the handle down and

PUSH THE CARRIAGE TOWARD THE GUIDE

FENCE AND THROUGH THE WORKPIECE.

When the cut is completed, switch off the tool and

WAIT UNTIL THE BLADE HAS COME TO A

COMPLETE STOP before returning the blade to its

fully elevated position.

WARNING:

• Whenever performing a slide cut, first pull the

carriage full towards you and press the handle

all the way down, then push the carriage

toward the guide fence. Never start the cut with

the carriage not pulled fully toward you. If you

perform the slide cut without the carriage pulled

fully toward you unexpected kickback may occur

and serious personal injury may result.

• Never attempt to perform a slide cut by pulling

the carriage towards you. Pulling the carriage

towards you while cutting may cause unexpected

kickback resulting in possible serious personal

injury.

• Never perform the slide cut with the handle locked

in the lowered position.

• Never loosen the locking screw which secures

the carriage while the blade is rotating. A loose

carriage while cutting may cause unexpected

kickback resulting in possible in serious personal

injury.

1. Locking screw

17

3. Miter cutting

Refer to the previously covered "Adjusting the miter

angle".

4. Bevel cut

Fig.37

Loosen the lever and tilt the saw blade to set the

bevel angle (Refer to the previously covered

"Adjusting the bevel angle"). Be sure to retighten

the lever firmly to secure the selected bevel angle

safely. Secure the workpiece with a vise. Make sure

the carriage is pulled all the way back toward the

operator. Switch on the tool without the blade

making any contact and wait until the blade attains

full speed. Then gently lower the handle to the fully

lowered position while applying pressure in parallel

with the blade and PUSH THE CARRIAGE

TOWARD THE GUIDE FENCE TO CUT THE

WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS

COME TO A COMPLETE STOP before returning

the blade to its fully elevated position.

WARNING:

• After setting the blade for a bevel cut, before

operating the tool ensure that the carriage and

blade will have free travel throughout the entire

range of the intended cut. Interruption of the

carriage or blade travel during the cutting operation

may result in kickback and serious personal injury.

• While making a bevel cut keep hands out of the

path of the blade. The angle of the blade may

confuse the operator as to the actual blade path

while cutting and contact with the blade will result in

serious personal injury.

• The blade should not be raised until it has

come to a complete stop. During a bevel cut the

piece cut off may come to rest against the blade. If

the blade is raised while it is rotating the cut-off

piece maybe ejected by the blade causing the

material to fragment which may result in serious

personal injury.

NOTICE:

• When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied

perpendicularly to the turn base or if the pressure

direction is changed during a cut, the precision of

the cut will be impaired.

• Before bevel-cutting, an adjustment of the upper

fence and lower fence maybe required. Refer to

the section titled "Guide fence adjustment".

CAUTION:

• Always remove the sub-fence R so that it does not

interfere any part of the carriage when performing

right bevel cuts.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter

angle is being cut on a workpiece. Compound

cutting can be performed at the angle shown in the

table.

Miter angle Bevel angle

Left and Right 0 - 45

009713

When performing compound cutting, refer to "Press

cutting", "Slide cutting", "Miter cutting" and "Bevel

cut" explanations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a

compound miter saw with the moldings laid flat on

the turn base.

There are two common types of crown moldings

and one type of cove moldings; 52/38° wall angle

crown molding, 45° wall angle crown molding and

45° wall angle cove molding. See illustrations.

Fig.38

There are crown and cove molding joints which are

made to fit "Inside" 90° corners ((1) and (2) in Fig.

A) and "Outside" 90° corners ((3) and (4) in Fig. A).

(1) (2) (3)(4)

1 2

Fig.A

001556

Fig.39

Measuring

Measure the wall length and adjust workpiece on

table to cut wall contact edge to desired length.

Always make sure that cut workpiece length

at the

back of the workpiece

is the same as wall length.

Adjust cut length for angle of cut. Always use

several pieces for test cuts to check the saw

angles.

When cutting crown and cove moldings, set the

bevel angle and miter angle as indicated in the

table (A) and position the moldings on the top

surface of the saw base as indicated in the table

(B).

1. Inside corner

2. Outside corner

18

In the case of left bevel cut

Molding

position in

Fig. A

Bevel angleMiter angle

For outside

corner

For inside

corner

52/38° type45° type

Right 31.6°

45° type

Left 33.9° Left 30°

52/38° type

Left 31.6° Left 35.3°

Right 35.3°

Right 35.3°Right 31.6°

(1)

(2)

(3)

(4)

Table (A)

006361

Molding

position in

Fig. A

Molding edge against

guide fence

(1)Ceiling contact edge should

be against guide fence.

Ceiling contact edge should

be against guide fence.

For

outside

corner

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

For inside

corner

Wall contact edge should be

against guide fence.

Finished piece

(2)

(3)

(4)

Table (B)

006362

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° LEFT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its CEILING CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will

always be on the LEFT side of the blade

after the cut has been made.

In the case of right bevel cut

Molding

position in

Fig. A

Bevel angleMiter angle

For outside

corner

For inside

corner

52/38° type45° type

Right 31.6°

45° type

Right 33.9° Right 30°

52/38° type

Left 31.6° Left 35.3°

Right 35.3°

Right 35.3°Right 31.6°

(1)

(2)

(3)

(4)

Table (A)

006363

Molding

position in

Fig. A

Molding edge against

guide fence

(1)

For

outside

corner

For inside

corner

Finished piece

(2)

(3)

(4)

Table (B)

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

Wall contact edge should be

against guide fence.

Wall contact edge should be

against guide fence.

Ceiling contact edge should

be against guide fence.

006364

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° RIGHT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its WALL CONTACT EDGE against

the guide fence on the saw.

• The finished piece to be used will

always be on the RIGHT side of the

blade after the cut has been made.

7. Cutting aluminum extrusion

Fig.40

Fig.41

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

WARNING:

• Never attempt to cut thick or round aluminum

extrusions. Thick or round aluminum extrusions

can be difficult to secure and may work loose

during the cutting operation which may result in

loss of control and serious personal injury.

8. Wood facing

Use of wood facing helps to assure splinter-free

cuts in workpieces. Attach a wood facing to the

guide fence using the holes in the guide fence.

See the figure concerning the dimensions for a

suggested wood facing.

15mm Over 500 mm

1

80mm-90mm

20 mm

68mm 121mm 68mm

121mm

24 mm

010563

CAUTION:

• Use straight wood of even thickness as the wood

facing.

WARNING:

• Use screws to attach the wood facing to the

guide fence. The screws should be installed

so that the screw heads are below the surface

of the wood facing so that they will not

interfere with the positioning of the material

1. Holes

19

being cut. Misalignment of the material being cut

can case unexpected movement during the

cutting operation which may result in a loss of

control and serious personal injury.

NOTICE:

• When the wood facing is attached, do not turn the

turn base with the handle lowered. The blade

and/or the wood facing will be damaged.

9. Groove cutting

Fig.42

A dado type cut can be made by proceeding as

follows:

Adjust the lower limit position of the blade using the

adjusting screw and the stopper arm to limit the

cutting depth of the blade. Refer to "Stopper arm"

section described previously.

After adjusting the lower limit position of the blade,

cut parallel grooves across the width of the

workpiece using a slide (push) cut as shown in the

figure. Then remove the workpiece material

between the grooves with a chisel.

WARNING:

• Do not attempt to perform this type of cut by

using a wider type blade or dado blade.

Attempting to make a groove cut with a wider blade

or dado blade could lead to unexpected cutting

results and kickback which may result in serious

personal injury

• Be sure to return the stopper arm to the

original position when performing other than

groove cutting. Attempting to make cuts with the

stopper arm in the incorrect position could lead to

unexpected cutting results and kickback which may

result in serious personal injury.

CAUTION:

•

Be sure to return the stopper arm to the original

position when performing other than groove cutting.

Carrying tool

Fig.43

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at the full right miter

angle position. Secure the slide poles so that the lower

slide pole is locked in the position of the carriage fully

pulled to operator and the upper poles are locked in the

position of the carriage fully pushed forward to the guide

fence (refer to the section titled "Slide lock adjustment ".)

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin.

Wind the power supply cord using the cord rests.

WARNING:

• Stopper pin is only for carrying and storage

purposes and should never be used for any

cutting operations. The use of the stopper pin for

cutting operations may cause unexpected

movement of the saw blade resulting in kickback

and serious personal injury.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily.

CAUTION:

• Always secure all moving portions before carrying

the tool. If portions of the tool move or slide while

being carried loss of control or balance may occur

resulting in personal injury.

MAINTENANCE

WARNING:

•

Always be sure that the tool is switched off

and unplugged before attempting to perform

inspection or maintenance.

Failure to unplug

and switch off the tool may result in accidental

start up of the tool which may result in serious

personal injury.

•

Always be sure that the blade is sharp and

clean for the best and safest performance.

Attempting a cut with a dull and /or dirty blade may

cause kickback and result in a serious personal

injury.

NOTICE:

•

Never use gasoline, benzine, thinner, alcohol or

the like. Discoloration, deformation or cracks may

result.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle

Fig.44

Push the carriage toward the guide fence and

tighten the locking screw to secure the carriage.

Loosen the grip which secures the turn base. Turn

the turn base so that the pointer points to 0° on the

miter scale. Then turn the turn base slightly

clockwise and counterclockwise to seat the turn

base in the 0° miter notch. (Leave as it is if the

pointer does not point to 0°.) Loosen the hex

sockets bolts securing the guide fence using the

socket wrench.

Fig.45

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the

side of the blade with the face of the guide fence

using a triangular rule, try-square, etc. Then

securely tighten the hex socket bolts on the guide

fence in order starting from the right side.

Fig.46

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen the

20

screw which secures the pointer and adjust the

pointer so that it will point to 0°.

2. Bevel angle

(1) 0° bevel angle

Fig.47

Push the carriage toward the guide fence

and tighten the locking screw to secure the

carriage. Lower the handle fully and lock it in

the lowered position by pushing in the

stopper pin. Loosen the lever at the rear of

the tool.

Fig.48

Turn the hex bolt on the right side of the arm

two or three revolutions counterclockwise to

tilt the blade to the right.

Fig.49

Carefully square the side of the blade with the

top surface of the turn base using the

triangular rule, try-square, etc. by turning the

hex bolt on the right side of the arm clockwise.

Then tighten the lever securely.

Fig.50

Make sure that the pointer on the arm point to

0° on the bevel scale on the arm holder. If

they do not point to 0°, loosen the screw

which secure the pointer and adjust it so that

it will point to 0°.

(2) 45° bevel angle

Fig.51

Adjust the 45° bevel angle only after

performing 0° bevel angle adjustment. To

adjust left 45° bevel angle, loosen the lever

and tilt the blade to the left fully. Make sure

that the pointer on the arm points to 45° on

the bevel scale on the arm holder. If the

pointer does not point to 45°, turn the 45°

bevel angle adjusting bolt on the right side of

the arm holder until the pointer points to 45°.

To adjust the right 45° bevel angle, perform

the same procedure as that described above.

Fig.52

Remove and check the carbon brushes regularly.

Replace when they wear down to 3 mm in length. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Fig.53

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

After use

• After use, wipe off chips and dust adhering to the

tool with a cloth or the like. Keep the blade guard

clean according to the directions in the previously

covered section titled "Blade guard". Lubricate the

sliding portions with machine oil to prevent rust.

• When storing the tool, pull the carriage toward you

fully.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

WARNING:

• These Makita accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments may result in serious

personal injury.

• Only use the Makita accessory or attachment

for its stated purpose. Misuse of an accessory or

attachment may result in serious personal injury.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Steel & Carbide-tipped saw blades

Miter saw blades

For smooth and precise cutting in various materials.

CombinationGeneral purpose blade for fast and smooth rip,

crosscuts and miters.

Crosscutting For smoother cross grain cuts. Slices cleanly

against the grain.

Fine cross cutsFor sand-free cuts cleanly against the grain.

Non-ferrous metals

miter saw blades

For miters in aluminum, copper, brass, tubing,

and other non-ferrous metals.

006526

• Sub-fence R

• Vise assembly (Horizontal vise)

• Vertical vise

• Socket wrench with hex wrench on its other end

• Holder

• Dust bag

• Elbow

• Triangular rule

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Strona się ładuje...

Makita LS1018L Slide Compound Miter Saw Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Makita LS1018L Slide Compound Miter Saw Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty