Indesit CE6VP6 (A) U instrukcja

Marka: Indesit

Model: CE6VP6 (A) U

Kategoria: Piekarniki

Typ: instrukcja

CE6VP6 U

CE6VP6 X U

Contents

Installation, 2-3

Positioning and levelling

Electrical connection

Technical data

Description of the appliance, 4

Overall view

Control panel

Start-up and use, 5-9

Starting the oven

Cooking modes

Practical cooking advice

Planning cooking with the electronic programmer

Oven cooking advice table

Using the glass ceramic hob, 10

Switching the cooking zones on and off

Cooking zones

Precautions and tips, 11

General safety

Disposal

Respecting and conserving the environment

Care and maintenance, 12-13

Switching the appliance off

Cleaning the appliance

Replacing the oven light bulb

Cleaning the glass ceramic hob

Assistance

Assembling the sliding rack kit

Operating Instructions

COOKER AND OVEN

English, 1

Polski, 14

 Before operating your new appliance please read

this instruction booklet carefully. It contains important

information concerning the safe installation and

operation of the appliance.

 Please keep these operating instructions for future

reference. Make sure that the instructions are kept with

the appliance if it is sold, given away or moved.

 The appliance must be installed by a qualified

professional according to the instructions provided.

 Any necessary adjustment or maintenance must be

performed after the appliance has been disconnected

from the electricity supply.

Positioning and levelling

 It is possible to install the appliance alongside

cupboards whose height does not exceed that of the

hob surface.

 Make sure that the wall in contact with the back of

the appliance is made from a non-flammable, heat-

resistant material (T 90°C).

To install the appliance correctly:

 Place it in the kitchen, dining room or the bed-sit

(not in the bathroom).

 If the top of the hob is higher than the cupboards,

the appliance must be installed at least 200 mm

away from them.

 If the cooker is

installed underneath a wall

cabinet, there must be a

minimum distance of 420

mm between this cabinet

and the top of the hob.

This distance should be

increased to 700 mm if

the wall cabinets are

flammable (see figure).

 Do not position blinds behind the cooker or less

than 200 mm away from its sides.

 Any hoods must be installed according to the

instructions listed in the relevant operating manual.

Levelling

If it is necessary to level the

appliance, screw the adjustable

feet* into the places provided on

each corner of the base of the

cooker (see figure).

The legs* provided with the

appliance fit into the slots on

the underside of the base of the

cooker.

Electrical connection

Fitting the power supply cable

Opening the terminal board:

 Using a screwdriver, prise on the side tabs of the

terminal board cover;

 Pull open the cover

of the terminal board.

To install the cable, proceed as follows:

 unscrew the wire clamp screw and the contact

screws

 The jumpers are factory-set for a single-phase

230V connection (see figure).

220-230V 1N~

H07RR-F 3x6 CEI-UNEL 35363

 to make the electrical connections illustrated in

figure, use the two jumpers housed in the box

(see figure - reference P)

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

Installation

Only available in certain models.

TECHNICAL DATA

Oven dimensions

(HxWxD)

32x43,5x40 cm

Volume

56 l

Useful

measurements

relating to the oven

compartment

width 42 cm

depth 44 cm

height 8,5 cm

Power supply

voltage and

frequency

see data plate

Electric hob

Front left

Back left

Back right

Front right

Maximum absorption

of the electric hob

1700 W

1200 W

2100 W

1200 W

6200 W

ENERGY LABEL

Directive 2002/40/EC on the

label of electric ovens.

Standard EN 50304

Energy consumption for Natural

convection – heating mode:

Traditional mode;

Declared energy consumption

for Forced convection Class –

heating mode:

Baking

mode.

EC Directives: 73/23/EEC dated

19/02/73 (Low Voltage) and

subsequent amendments -

89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent amendments -

93/68/EEC dated 22/07/93 and

subsequent amendments -

2002/96/EC.

NL1L2

380-400V 2N~

H05RR-F 4x4 CEI-UNEL 35363

NL1L3L2

380-400V 3N~

H05RR-F 5x2.5 CEI-UNEL 35363

 fasten the supply cable in place with the clamp

and close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the

load indicated on the data plate located on the

appliance.

The appliance must be directly connected to the

mains using an omnipolar circuit-breaker with a

minimum contact opening of 3 mm installed between

the appliance and the mains. The circuit-breaker

must be suitable for the charge indicated and must

comply with current electrical regulations (the

earthing wire must not be interrupted by the circuit-

breaker). The supply cable must be positioned so

that it does not come into contact with temperatures

higher than 50°C at any point.

Before connecting the appliance to the power

supply, make sure that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated by the data

plate.

 The voltage is in the range between the values

indicated on the data plate.

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket must be

easily accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced

by authorised technicians only.

 The manufacturer declines any liability should

these safety measures not be observed.

Description of the appliance

Overall view

Control panel

THERMOSTAT

knob

ACTIVE HOTPLATE

indicator light

ELECTRIC HOTPLATE

control knobs

SELECTOR

knob

THERMOSTAT

indicator light

Electronic

cooking

programmer*

TIMER button

COOKING END TIME button

COOKING TIME button

OVEN

OPERATION

indicator light

Control panel

GRILL rack

Glass

ceramic hob

DRIPPING pan

GUIDE RAILS

for the sliding racks

position 3

position 2

position 1

Adjustable foot

position 5

position 4

Start-up and use

 The first time you use your appliance, heat the

empty oven with its door closed at its maximum

temperature for at least half an hour. Ensure that the

room is well ventilated before switching the oven off

and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective

substances used during the manufacturing process

burning away.

 Should the appliance be equipped with an

electronic programmer, to use the electric oven, just

press buttons

and at the same time (the

symbol will appear on the display) before selecting

the desired cooking function.

Starting the oven

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the recommended temperature for the

cooking mode or the desired temperature by turning

the THERMOSTAT knob.

A list detailing cooking modes and suggested

cooking temperatures can be found in the relevant

table (see Oven cooking advice table).

During cooking it is always possible to:

 Change the cooking mode by turning the

SELECTOR knob.

 Change the temperature by turning the

THERMOSTAT knob.

 Set the total cooking time and the cooking end

time (see below).

 Stop cooking by turning the SELECTOR knob to

the 0 position.

 Never put objects directly on the bottom of the

oven; this will avoid the enamel coating being

damaged. Only use position 1 in the oven when

cooking with the rotisserie spit.

 Always place cookware on the rack(s) provided.

THERMOSTAT indicator light

When this is illuminated, the oven is generating heat. It

switches off when the inside of the oven reaches the

selected temperature. At this point the light

illuminates and switches off alternately, indicating

that the thermostat is working and is maintaining the

temperature at a constant level.

Oven light

This is switched on by turning the SELECTOR knob to

any position other than 0. It remains lit as long as the

oven is operating. By selecting

with the knob,

the light is switched on without any of the heating

elements being activated.

Cooling ventilation

In order to cool down the external temperature of the

oven, some models are fitted with a cooling fan that

blows out air between the control panel and the oven

door.

! Once the cooking has been completed, the cooling

fan remains on until the oven has cooled down

sufficiently.

Cooking modes

! A temperature value can be set for all cooking

modes between 50°C and Max, except for

 BARBECUE (recommended: set only to MAX

power level);

 GRATIN (recommended: do not exceed 200°C).

TRADITIONAL OVEN mode

Both the top and bottom heating elements will come

on. With this traditional cooking mode, it is best to

use one cooking rack only: if more than one rack is

used, the heat distribution will be uneven.

BAKING mode

The rear heating element and the fan come on,

guaranteeing the distribution of heat delicately and

uniformly throughout the oven. This mode is ideal for

baking and cooking temperature sensitive foods

such as cakes that need to rise and to prepare

certain tartlets on 3 shelves simultaneously.

FAST COOKING mode

The heating elements and the fan come on,

guaranteeing the distribution of heat consistently

and uniformly throughout the oven.

Pre-heating is not necessary for this cooking mode.

This mode is especially recommended for cooking

pre-packed food quickly (frozen or pre-cooked). The

best results are obtained if you use one cooking

rack only.

MULTI-COOKING mode

All the heating elements (top, bottom and circular),

as well as the fan, will come on. Since the heat

remains constant throughout the oven, the air cooks

and browns food uniformly. A maximum of two racks

may be used at the same time.

PIZZA mode

The heating elements (bottom and circular) and the

fan come on. This combination heats the oven

rapidly by producing a considerable amount of heat,

particularly from the bottom element. If you use more

than one rack simultaneously, switch the position of

the dishes halfway through the cooking process.

BARBECUE mode

The top heating element and the rotisserie (where

present) come on. The high and direct temperature of

the grill is recommended for food that requires high

surface temperature.

GRATIN mode

The top heating element as well as the fan and the

rotisserie (where present) come on. This combination

of features increases the effectiveness of the

unidirectional thermal radiation of the heating

elements through forced circulation of the air

throughout the oven.

This helps prevent food from burning on the surface,

allowing the heat to penetrate right into the food.

! In the BARBECUE and GRATIN cooking modes

with the oven door closed.

Spit roast (only available in certain models)

To operate the spit roast

function (see diagram)

proceed as follows:

1. Place the dripping pan in position 1.

2. Place the rotisserie support in position 3 and insert

the spit in the hole provided on the back panel of

the oven.

3. Start the rotisserie using the SELECTOR knob to

select mode

or .

! When the

mode is activated, the spit will stop if

the door is opened.

* Only available in certain models.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-

assisted cooking. Excessive direct heat can burn

temperature sensitive foods.

! In the BARBECUE and GRATIN cooking modes,

particularly when using the rotisserie, place the

dripping pan in position 1 to collect cooking

residues (fat and/or grease).

MULTI-COOKING

 Use position 2 and 4, placing the food that

requires more heat on 2.

 Place the dripping pan on the bottom and the rack

on top.

BARBECUE

 Insert the rack in position 3 or 4. Place the food in

the centre of the rack.

 We recommend that you set the maximum power

level. The top heating element is regulated by a

thermostat and may not always be on.

PIZZA MODE

 Use a light aluminium pizza pan. Place it on the

rack provided.

For a crispy crust, do not use the dripping pan

(prevents crust from forming by extending

cooking time).

 If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

Planning cooking with the electronic

programmer

Setting the clock

After the appliance has been connected to the power

supply, or after a blackout, the display will automatically

reset to 0:00 and begin to blink. To set the time:

1. Press the COOKING TIME button

and the

COOKING END TIME

simultaneously.

2. Within 4 seconds of having pressed these buttons, set

the exact time by pressing the

and

)

buttons. The

button advances the hours and the

)

button decreases

the hours.

Once the time has been set, the programmer

automatically switches to manual mode.

Setting the timer

The timer enables a countdown to be set, when the time

has elapsed a buzzer sounds.

To set the timer proceed as follows:

1. press the TIMER button

H. The display shows:

2. Press the

and

)

buttons to set the desired time.

3. When the buttons are released the timer begins

counting down and the current time appears on the

display.

4. After the time has elapsed a buzzer will sound,

and this can be switched off by pressing any button

(except the

and

)

buttons). The symbol

will

switch off.

! The timer does not switch the oven on or off.

Adjusting the volume of the buzzer

After selecting and confirming the clock settings, use the

)

button to adjust the volume of the alarm buzzer.

Setting the cooking time with a delayed start

First decide which cooking mode you wish to use and set

a suitable temperature using the SELECTOR and

THERMOSTAT knobs on the oven.

At this point it is possible to set the cooking time:

1. Press the COOKING TIME button

2. Within 4 seconds of having pressed this button, set the

desired amount of time by pressing the

and

)

buttons.

If, for example, you wish to set a cooking time of 30

minutes, the display will show:

3. 4 seconds after the buttons are released, the

current time (for example 10.00) reappears on the

display with the symbol

and the letter A (AUTO).

Next the desired cooking end time must be set:

4. Press the END COOKING TIME button

5. Within 4 seconds of having pressed this button,

adjust the cooking end time by pressing the

and

)

buttons. If, for example, you want cooking to end

at 13.00, the display shows:

6. 4 seconds after the buttons are released, the

current time (for example 10.00) reappears on the

display with the letter A (AUTO).

At this point, the oven is programmed to switch on

automatically at 12:30 and switch off after 30

minutes, at 13.00.

Setting the cooking time with an immediate start

Follow the above procedure for setting the cooking time

(points 1-3).

 When the letter A appears, this indicates that both the

cooking time and the end cooking time have been

programmed in AUTO mode. To restore the oven to

manual operation, after each AUTO cooking mode press

the COOKING TIME

and END COOKING TIME

buttons simultaneously.

 The symbol

will remain lit, along with the oven, for

the entire duration of the cooking programme.

The set cooking duration can be displayed at any time by

pressing the COOKING TIME button

$>$

, and the

cooking end time may be displayed by pressing the END

COOKING TIME button

. When the cooking time has

elapsed a buzzer sounds. To stop it, press any button

apart from the

and

)

buttons.

Cancelling a previously set cooking programme

Press the COOKING TIME button

and the

COOKING END TIME

simultaneously.

Correcting or cancelling previously set data

The data entered can be changed at any time by

pressing the corresponding button (TIMER, COOKING

TIME or COOKING END TIME) and the

)

button.

When the cooking time data is cancelled, the cooking end

time data is also cancelled automatically, and vice versa.

If the oven has already been programmed, it will not

accept cooking end times which are before the start of the

programmed cooking process.

Oven cooking advice table

Cooking

modes

Foods Weight

(in kg)

Rack Position Pre-heating

time

(minutes)

Recommended

temperature

Cooking

time

(minutes)

Traditional

Oven

Duck

Roast veal or beef

Pork roast

Biscuits (short pastry)

Tarts

200

180

65-75

70-75

70-80

15-20

30-35

Baking

Mode

Tarts

Fruit cakes

Plum cake

Sponge cake

Stuffed pancakes (on 2 racks)

Small cakes (on 2 racks)

Cheese puffs (on 2 racks)

Cream puffs (on 3 racks)

Biscuits (on 3 racks)

Meringues (on 3 racks)

0.5

0.7

0.5

1.2

0.6

0.4

0.7

0.5

2 or 3

2 and 4

1 and 3 and 5

180

160

200

190

210

180

20-30

40-45

40-50

25-30

30-35

20-25

15-20

20-25

180

Frozen food

Pizza

Courgette and prawn pie

Country style spinach pie

Turnovers

Lasagne

Golden Rolls

Chicken morsels

0.3

0.4

0.5

0.3

0.5

0.4

250

200

220

200

180

220

30-35

25-30

15-20

2re-cooked food

Golden chicken wings

0.4

200

20-25

Fast

cooking

Fresh Food

Biscuits (short pastry)

Plum cake

Cheese puffs

0.3

0.6

0.2

200

180

210

15-18

10-12

Multi-

cooking

Pizza (on 2 racks)

Lasagne

Lamb

Roast chicken + potatoes

Mackerel

Plum cake

Cream puffs (on 2 racks)

Biscuits (on 2 racks)

Sponge cake (on 1 rack)

Sponge cake (on 2 racks)

Savoury pies

1+1

0.5

1.5

2 and 4

and 4

2 and 4

230

180

200

180

170

190

180

170

200

15-20

30-35

40-45

60-70

30-35

40-50

20-25

10-15

15-20

20-25

25-30

Pizza Mode

Pizza

Roast veal or beef

Chicken

0.5

2 or 3

220

180

15-20

25-30

60-70

Soles and cuttlefish

Squid and prawn kebabs

Cuttlefish

Cod filet

Grilled vegetables

Veal steak

Sausages

Hamburgers

Mackerels

Toasted sandwiches (or toast)

0.7

0.6

0.8

0.4

0.8

0.6

4 and 6

3 or 4

Max

10-12

8-10

10-15

15-20

10-12

15-20

3-5

Barbecue

With rotisserie

(where present)

Veal on the spit

Chicken on the spit

Lamb on the spit

1.0

1.5

1.0

Max

80-90

70-80

Grilled chicken

Cuttlefish

1.5

200

55-60

30-35

Gratin

With rotisserie

(where present)

Veal on the spit

Lamb on the spit

Chicken (on the spit) +

potatoes (roasted)

1.5

200

70-80

70-75

Using the glass ceram ic hob

 The glue applied on the gaskets leaves traces of

grease on the glass. Before using the appliance, we

recommend you remove these with a special non-

abrasive cleaning product. During the first few hours

of use there may be a smell of rubber which will

disappear very quickly.

Switching the cooking zones on and off

To switch on a cooking zone, turn the corresponding

knob in a clockwise direction.

To switch it off again, turn the knob in an

anticlockwise direction until it is in the "0" position.

If the ELECTRIC HOTPLATE ON indicator light is lit,

this shows that at least one hotplate on the hob is

switched on.

Cooking zones

The hob is equipped with electric halogen heating

elements. When they are in use the following items

on the hob become red.

A. The cooking zone with

halogen heating elements.

B. The residual heat indicator

light: this indicates that the

temperature of the

corresponding cooking zone

is greater than 60°C, even when the heating element

has been switched off but is still hot.

Cooking zones with halogen heating elements

These emit heat via radiation from the halogen

lamps they contain. They have similar properties to

gas burners: they are easy to control and reach set

temperatures quickly, allowing you to actually see

the power they are providing.

 Do not stare directly at the halogen heating elements.

Turn the corresponding knob in a clockwise

direction, to a position between 1 and 6.

Setting Normal or Fast Plate

Off

Cooking vegetables, fish

Cooking potatoes (using steam) soups,

chickpeas, beans.

Continuing the cooking of large quantities

of food, minestrone

For roasting (average)

For roasting (above average)

For browning and reaching a boil in a

short time.

Practica l advice on using the hob

 Use pans with a thick, flat base to ensure that

they adhere perfectly to the cooking zone.

 Always use pans with a diameter that is large

enough to cover the hotplate fully, in order to use

all the heat produced.

 Always make sure that the base of the pan is

completely clean and dry: this ensures that the

pans adhere perfectly to the cooking zones and

that both the pans and the hob last for a longer

period of time.

 Avoid using the same cookware that is used on

gas burners: the heat concentration on gas

burners may have warped the base of the pan,

causing it not to adhere to the surface correctly.

 Never leave a cooking zone switched on without a

pan on top of it, as doing so may cause the zone

to become damaged.

Precautions and tips

 This appliance has been designed and manufactured in

compliance with international safety standards.

The following warnings are provided for safety reasons and

must be read carefully.

General safety

 These instructions are only valid for the countries

whose symbols appear in the manual and on the

serial number plate.

 The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial

use.

 The appliance must not be installed outdoors, even

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

Do not touch the appliance with bare feet or with wet or

damp hands and feet.

 The appliance must be used by adults only for the

preparation of food, in accordance with the instructions

provided in this booklet.

 The

instruction booklet accompanies a class 1

(insulated) or class 2 - subclass 1 (recessed between 2

cupboards) appliance.

 When the appliance is in use, the heating elements

and some parts of the oven door become extremely

hot. Make sure you don'

t touch them and keep

children well away.

 Make sure that the power supply cables of other

electrical appliances do not come into contact with the

hot parts of the oven.

 The openings used for the ventilation and dispersion of

heat must never be covered.

Do not place unstable or

misshapen pans on the

electric hotplates; this will help to avoid spills. Position

them on the hob with the handles turned towards the

centre of the appliance.

 Always use oven gloves when placing cookware in the

oven or when removing it.

Do not use flammable liquids (alcohol, petrol, etc...) near

the appliance while it

is in use.

Do not place flammable material in the lower storage

compartment or in the oven itself. If the appliance is

switched on accidentally, it could catch fire.

 Always make sure the knobs are in the 0 position when

the appliance is not in use.

 When unplugging the appliance, always pull the

plug

from the mains socket; do not pull on the cable.

 Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

If the appliance breaks down, under no circumstances

should you attempt to repair the appliance yourself.

Repairs carried out by inexperienced persons may

cause injury or further malfunctioning

of the appliance.

Contact Assistance.

Do not rest heavy objects on the open oven door.

 The internal surfaces of the compartment (where

present) may become hot.

 The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with a

sharp object such as a tool. If this

happens, disconnect

the appliance from the electricity mains immediately and

contact a Service Centre.

If the surface of the hob is cracked, switch off the

appliance to prevent electric shocks from occurring.

 Remember that the temperature of the cooking zones

remains relatively high for at least thirty minutes after

they have been switched off.

 Keep any object that could melt away from the hob, for

example plastic and aluminium objects, or products with

a high sugar content. Keep plastic or aluminium objects

away from the hob: if you forget them on surfaces that

are still hot, they may cause serious damage to the hob.

Do not place

metal objects (knives, spoons, pan lids,

etc.) on the hob as they may become hot.

Disposal

 When disposing of packaging material: observe local

legislation so that the packaging may be reused.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the

cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health. The crossed-out

dustbin is marked on all products to remind the owner of

their obligations regarding separated waste collection.

Exhausted appliances may be collected by the public

waste collection service, taken to suitable

collection

areas in the area or, if permitted by current national

legislation, they may be returned to the dealers as part of

an exchange deal for a new equivalent product.

All major manufacturers of household appliances

participate in the creation and organisation of systems

for the collection and disposal of old and disused

appliances.

Respecting and conserving the

environment

 You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of the

morning.

 Always keep the oven door closed when using the

BARBECUE and GRATIN modes: to attain best results

and to save energy (approximately

10%).

 Check the door seals regularly and wipe them clean to

ensure they are free of debris so that they adhere

properly to the door, thus avoiding heat dispersion.

Switching the appliance off

Disconnect your appliance from the electricity supply

before carrying out any work on it.

Cleaning the appliance

 Never use steam cleaners or pressure cleaners on

the appliance.

 Clean the glass part of the oven door using a

sponge and a non-abrasive cleaning product, then

dry thoroughly with a soft cloth. Do not use rough

abrasive material or sharp metal scrapers as these

could scratch the surface and cause the glass to

crack.

 The stainless steel or enamel-coated external parts

and the rubber seals may be cleaned using a

sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for the

removal of stubborn stains. After cleaning, rinse and

dry thoroughly. Do not use abrasive powders or

corrosive substances.

 The inside of the oven should ideally be cleaned

after each use, while it is still lukewarm. Use hot

water and detergent, then rinse well and dry with a

soft cloth. Do not use abrasive products.

 The accessories can be washed like everyday

crockery, and are even dishwasher safe.

 Dirt and grease should be removed from the control

panel using a non-abrasive sponge or a soft cloth.

 Stainless steel can be marked by hard water that

has been left on the surface for a long time, or by

aggressive detergents containing phosphorus. After

cleaning, rinse well and dry thoroughly. Any

remaining drops of water should also be dried.

Inspecting the oven seals

Check the door seals around the oven regularly. If the

seals are damaged, please contact your nearest After-

sales Service Centre. We recommend that the oven is

not used until the seals have been replaced.

Replacing the oven light bulb

1. After disconnecting the oven

from the electricity mains,

remove the glass lid covering

the lamp socket (see figure).

2. Remove the light bulb and

replace it with a similar one:

voltage 230 V, wattage 25 W,

cap E 14.

3. Replace the lid and reconnect the oven to the

electricity supply.

Cleaning the glass ceramic hob

 Do not use abrasive or corrosive detergents (for example,

products in spray cans for cleaning barbecues and ovens),

stain removers, anti-rust products, powder detergents or

sponges with abrasive surfaces: these may scratch the

surface beyond repair.

It is usually sufficient simply to wash the hob using

a damp sponge and dry it with absorbent kitchen

roll.

If the hob is particularly dirty, rub it with a special

glass ceramic cleaning product, then rinse well and

dry thoroughly.

To remove more stubborn dirt, use a suitable

scraper (this is not supplied

with the appliance).

Remove spills as soon as possible, without waiting

for the appliance to cool, to avoid residues forming

crusty deposits. You can obtain excellent results by

using a rustproof steel wire sponge - specifically

designed for glass ceramic surfaces - soaked in

soapy water.

If plastic or sugary substances have accidentally

been melted

on the hob, remove them immediately

with the scraper, while the surface is still hot.

 Once it is clean, the hob may be treated with a

special protective maintenance product: the

invisible film left by this product protects the

surface from drips during cooking. This

maintenance should be carried out while the

appliance is

warm (not hot) or cold.

 Always remember to rinse the appliance well with

clean water and dry it thoroughly: residues can

become encrusted during subsequent cooking

processes.

Glass ceramic hob

cleaners

Available from

Window scraper Razor blade

scrapers

DIY Stores

Replacement blades DIY Stores,

supermarkets,

chemists

COLLO luneta

HOB BRITE

Hob Clean

SWISSCLEANER

Boots, Co-op stores,

department stores, Regional

Electricity Company shops,

supermarkets

Assistance

Please have the following information to hand:

 The appliance model (Mod.).

 The serial number (S/N).

This information can be found on the data plate located

on the appliance and/or on the packaging.

Care and maintenance

Assembling the sliding rack kit

To assemble the sliding racks:

1. Remove the two

frames, lifting them

away from the spacers

A (see figure).

2. Choose which shelf

to use with the sliding

rack. Paying attention

to the direction in which

the sliding rack is to be

extracted, position joint

B and then joint C on

the frame.

3. Secure the two

frames with the guide

rails using the holes

provided on the oven

walls (see diagram).

The holes for the left

frame are situated at

the top, while the holes

for the right frame are

at the bottom.

4. Finally, fit the frames on the spacers A.

 Do not place the sliding racks in position 5.

Left

guide rail

Right guide

rail

Direction

of extraction

KUCHENKA I PIEKARNIK

Spis treci

Instalacja, 15-16

Ustawienie i wypoziomowanie

Pod³¹czenie do sieci elektrycznej

Tabela charakterystyk

Opis urz¹dzenia, 17

Widok ogólny

Panel kontrolny

Uruchomienie i u¿ytkowanie, 18-22

Uruchomienie piekarnika

Programy pieczenia

Praktyczne porady dotycz¹ce pieczenia

Programowanie pieczenia z u¿yciem programatora

elektronicznego

Tabela pieczenia w piekarniku

U¿ytkowanie p³yty grzejnej ze szk³a

ceramicznego, 23

W³¹czanie i wy³¹czanie stref pieczenia

Strefy pieczenia

Zalecenia i rodki ostro¿noci, 24

Ogólne zasady bezpieczeñstwa

Zalecenia dotycz¹ce odpadów

Oszczêdnoæ i ochrona rodowiska

Konserwacja i utrzymanie, 25-26

Od³¹czenie pr¹du elektrycznego

Czyszczenie urz¹dzenia

Wymiana ¿arówki owietleniowej w piekarniku

Czyszczenie p³yty grzejnej ze szk³a ceramicznego

Serwis Techniczny

Monta¿ zestawu prowadnic lizgowych

Instrukcja obs³ugi

CE6VP6 U

CE6VP6 X U

English, 1

Polski, 14

 Nale¿y zachowaæ niniejsz¹ instrukcjê, aby móc z

niej korzystaæ w ka¿dej chwili. W przypadku

sprzeda¿y, odst¹pienia lub przeniesienia urz¹dzenia,

nale¿y upewniæ siê, czy instrukcja zosta³a

przekazana wraz z nim.

 Nale¿y uwa¿nie przeczytaæ instrukcjê: zawiera ona

wa¿ne informacje dotycz¹ce instalacji, u¿ytkowania i

bezpieczeñstwa.

 Instalacja urz¹dzenia powinna zostaæ wykonana

zgodnie z niniejszymi instrukcjami i przez

wykwalifikowany personel.

 Wszelkie dzia³ania w zakresie regulacji lub

konserwacji musz¹ byæ wykonywane przy kuchence

od³¹czonej od zasilania elektrycznego.

Ustawienie i wypoziomowanie

 Mo¿liwe jest zainstalowanie urz¹dzenia obok mebli,

których wysokoæ nie przekracza wysokoci p³yty

roboczej.

 Nale¿y upewniæ siê, czy ciana stykaj¹ca siê z

ty³em urz¹dzenia wykonana jest z materia³u

niepalnego i odpornego na ciep³o (T 90°C).

Dla zapewnienia prawid³owej instalacji:

 ustawiæ urz¹dzenie w kuchni, w jadalni lub w

innym pomieszczeniu (nie w ³azience);

 jeli p³aszczyzna kuchenki jest wy¿sza w

stosunku do p³aszczyzny mebli, powinny one

zostaæ umieszczone w odleg³oci co najmniej 600

mm od urz¹dzenia;

 jeli kuchenka jest

instalowana pod szafk¹

wisz¹c¹, powinna ona

znajdowaæ siê w

odleg³oci minimum

420 mm od p³yty

kuchenki. Odleg³oæ ta

powinna wynosiæ 700

mm, jeli szafki

wisz¹ce s¹ ³atwopalne

(patrz rysunek);

 nie umieszczaæ zas³on za kuchenk¹, ani w

odleg³oci mniejszej ni¿ 200 mm od jej krawêdzi;

 ewentualne okapy powinny zostaæ zainstalowane

wed³ug zaleceñ odpowiedniej instrukcji.

Wypoziomowanie

Jeli konieczne jest

wypoziomowanie urz¹dzenia,

nale¿y przykrêciæ nó¿ki

regulacyjne, dostarczane jako

wyposa¿enie, w odpowiednich

gniazdach umieszczonych w

rogach podstawy kuchenki

(patrz rysunek).

Nó¿ki* mocowane s¹ w

otworach pod podstaw¹

kuchenki.

Pod³¹czenie do sieci elektrycznej

Monta¿ przewodu zasilaj¹cego

Otwarcie skrzynki zaciskowej:

 Pos³uguj¹c siê rubokrêtem podwa¿yæ boczne

zatrzaski pokrywy skrzynki zaciskowej;

 Poci¹gn¹æ i

otworzyæ pokrywê

skrzynki zaciskowej.

Zamontowaæ przewód wykonuj¹c nastêpuj¹ce

czynnoci:

 odkrêciæ rubê zacisku i ruby styków

 Mostki s¹ fabrycznie dostosowane do pod³¹czenia

jednofazowego 230 V (patrz rysunek).

220-230V 1N~

H07RR-F 3x6 CEI-UNEL 35363

 w celu wykonania pod³¹czeñ elektrycznych

elementów nale¿y wykorzystaæ dwa mostki

znajduj¹ce siê wewn¹trz skrzynki (patrz rysunek -

odnonik P)

Instalacja

HOOD

420

Min.

min. 650 mm. with hood

min.

700 mm. without hood

mm.

600

Min. mm.

420

Min. mm.

Znajduje siê tylko w niektórych modelach.

 zamocowaæ przewód zasilaj¹cy w odpowiednim

zacisku i zamkn¹æ pokrywê.

Pod³¹czenie przewodu zasilaj¹cego do sieci.

Zamocowaæ na przewodzie znormalizowan¹ wtyczkê

dostosowan¹ do obci¹¿eñ wskazanych na tabliczce

znamionowej umieszczonej na urz¹dzeniu (patrz

tabela Dane techniczne).

W przypadku bezporedniego pod³¹czenia do sieci

konieczne jest zainstalowanie pomiêdzy

urz¹dzeniem a sieci¹ wy³¹cznika wielobiegunowego z

minimalnym otwarciem pomiêdzy stykami

wynosz¹cym 3 mm, dostosowanego do obci¹¿enia i

odpowiadaj¹cego obowi¹zuj¹cym normom krajowym

(przewód uziemienia nie powinien byæ przerywany

przez wy³¹cznik). Przewód zasilania powinien byæ

umieszczony tak, aby w ¿adnym punkcie jego

temperatura nie przekracza³a temperatury otoczenia

o 50°C.

Przed wykonaniem pod³¹czenia nale¿y upewniæ siê,

czy:

 gniazdko posiada uziemienie i jest zgodne z

obowi¹zuj¹cymi przepisami;

 gniazdko jest w stanie wytrzymaæ maksymalne

obci¹¿enie mocy urz¹dzenia, wskazane na

tabliczce znamionowej;

 napiêcie zasilania odpowiada wartociom podanym

na tabliczce znamionowej;

 gniazdko jest kompatybilne z wtyczk¹ urz¹dzenia.

Jeli gniazdko nie jest kompatybilne, wymieniæ

gniazdko lub wtyczkê; nie stosowaæ przed³u¿aczy

ani rozga³êników.

NL1L2

380-400V 2N~

H05RR-F 4x4 CEI-UNEL 35363

NL1L3L2

380-400V 3N~

H05RR-F 5x2.5 CEI-UNEL 35363

 Po zainstalowaniu urz¹dzenia przewód elektryczny i

gniazdko pr¹du powinny byæ ³atwo dostêpne.

 Kabel nie powinien byæ zginany ani przygniatany.

 Przewód musi byæ okresowo sprawdzany i

wymieniany wy³¹cznie przez autoryzowany personel

techniczny.

 Producent nie ponosi ¿adnej

odpowiedzialnoci za skutki wynik³e z

nieprzestrzegania powy¿szych zasad.

TABELA CHARAKTERYSTYK

Wymiary piekarnika

W x D x G

32x43,5x40 cm

Objêtoæ

lt. 56

Wymiary u¿ytkowe

szuflady do

podgrzewania potraw

szerokoæ 42 cm, g³êbokoæ

44 cm, wysokoæ 8,5 cm

Napiêcie i

czêstotliwoæ zasilania

elektrycznego

patrz tabliczka znamionowa

P³yta grzejna ze szk³a

ceramicznego

Przód lewa

Ty³ lewa

Ty³ prawa

Przód prawa

MAX moc poch³aniana

przez ceramiczne p³yty

grzejne

1700 W

1200 W

2100 W

1200 W

6200 W

ENERGY LABEL

Dyrektywa 2002/40/WE na

etykiecie piekarników

elektrycznych Norma EN

50304

Zu¿ycie energii konwekcja

naturalna - funkcja

ogrzewania: Tradycyjny;

Zu¿ycie energii deklaracja

Klasy konwekcja wymuszona -

funkcja ogrzewania:

Piekarnictwo

Niniejsze urz¹dzenie zosta³o

wyprodukowane zgodnie z

nastêpuj¹cymi dyrektywami

unijnymi: 73/23/EWG z dnia

19/02/73 (niskie napiêcie) z

póniejszymi zmianami

89/336/EWG z dnia 3/05/89

(zgodnoæ

elektromagnetyczna) z

póniejszymi zmianami

93/68/EWG z dnia 22/07/93 z

póniejszymi zmianami,

90/369/EWG z dnia 29/06/90

(gaz) z póniejszymi

zmianami, -93/68/EWG z dnia

22/07/93 z póniejszymi

zmianami, - 2002/96/WE.

Opis urz¹dzenia

Widok ogólny

Panel kontrolny

Poziom RUSZT

Poziom BRYTFANNA

PROWADNICE

ślizgu półek

pozycja 3

pozycja 2

pozycja 1

Płyta grzejna ze

szkła ceramicznego

Nóżka regulowana

pozycja 5

pozycja 4

Lampka kontrolna

FUNKCJONOWANIE

PIEKARNIKA

Kontrolka

TERMOSTAT

Elektroniczny

programator

pieczenia*

Przycisk MINUTNIK

Przycisk KONIEC PIECZENIA

Przycisk CZAS TRWANIA PIECZENIA

Uruchomienie i u¿ytkowanie

 Przy pierwszym w³¹czeniu nale¿y uruchomiæ pusty

piekarnik na przynajmniej jedn¹ godzinê, z

termostatem ustawionym na maksimum i z

zamkniêtymi drzwiczkami. Nastêpnie wy³¹czyæ go,

otworzyæ drzwiczki piekarnika i przewietrzyæ

pomieszczenie. Zapach, który siê wytworzy³, jest

skutkiem parowania substancji stosowanych w celu

zabezpieczenia piekarnika.

 Aby skorzystaæ z piekarnika elektrycznego w

urz¹dzeniach wyposa¿onych w programator

elektroniczny, nale¿y nacisn¹æ równoczenie

przyciski

i (na wywietlaczu pojawi siê

symbol

), a nastêpnie wybraæ ¿¹dan¹ funkcjê

pieczenia.

Uruchomienie piekarnika

1. Wybraæ ¿¹dany program pieczenia obracaj¹c

pokrêt³em PROGRAMY.

2. Wybraæ temperaturê zalecan¹ dla danego

programu lub inn¹ ¿¹dan¹ temperaturê obracaj¹c

pokrêt³em TERMOSTAT.

Wykaz potraw z zalecanymi dla nich temperaturami

znajduje siê w odpowiedniej tabeli (patrz Tabela

pieczenia w piekarniku).

Podczas pieczenia mo¿na zawsze:

 zmieniæ program pieczenia pos³uguj¹c siê

pokrêt³em PROGRAMY;

 zmieniæ temperaturê pos³uguj¹c siê pokrêt³em

TERMOSTAT;

 zaprogramowaæ czas trwania pieczenia i godzinê

jego zakoñczenia (patrz ni¿ej);

 przerwaæ pieczenie przestawiaj¹c pokrêt³o

PROGRAMY na pozycjê 0.

 Nie stawiaæ nigdy ¿adnych przedmiotów na dnie

piekarnika, gdy¿ grozi to uszkodzeniem emalii.

Wykorzystywaæ pozycjê 1 piekarnika jedynie w

przypadku pieczenia z u¿yciem ro¿na.

 Naczynia do pieczenia stawiaæ zawsze na ruszcie

znajduj¹cym siê w wyposa¿eniu piekarnika.

Kontrolka TERMOSTAT

Jej zawiecenie siê sygnalizuje, ¿e piekarnik

wytwarza ciep³o. Ganie, kiedy wewn¹trz piekarnika

osi¹gniêta zostaje ustawiona temperatura. W tym

momencie kontrolka zapala siê i ganie

naprzemiennie, wskazuj¹c, ¿e termostat pracuje i

utrzymuje sta³¹ temperaturê.

Owietlenie piekarnika

W³¹cza siê przy ustawieniu pokrêt³a PROGRAMY na

dowoln¹ pozycjê, ró¿n¹ ni¿ 0, i pozostaje w³¹czone

tak d³ugo, jak d³ugo piekarnik pracuje. Po wybraniu

przy pomocy pokrêt³a, wiate³ko zapala siê bez

uruchamiania ¿adnego z elementów grzejnych.

Ch³odzenie poprzez wentylacjê

W celu zmniejszenia temperatury zewnêtrznej wentylator

ch³odz¹cy wytwarza strumieñ powietrza, który wychodzi

miêdzy panelem kontrolnym a drzwiczkami piekarnika.

 Po zakoñczeniu gotowania wentylator pracuje dopóty,

dopóki piekarnik wystarczaj¹co siê nie och³odzi.

Programy pieczenia

 Dla wszystkich programów mo¿liwe jest ustawienie

temperatury w zakresie od 50 °C do MAX, z

wyj¹tkiem:

 GRILL (zaleca siê ustawiaæ jedynie na MAX);

 ZAPIEKANKA (zaleca siê, aby nie przekraczaæ

temperatury 200°C).

Program PIEKARNIK TRADYCYJNY

Uruchamiane s¹ dwa elementy grzewcze: dolny i

górny. Przy tym tradycyjnym sposobie pieczenia

lepiej jest stosowaæ tylko jeden poziom: przy

zastosowaniu wiêkszej liczby poziomów wystêpuje

niekorzystny rozk³ad temperatur.

Program PIEKARNIK DO WYPIEKU CIAST

W³¹cza siê tylny element grzejny oraz uruchamia siê

wentylator, zapewniaj¹c wewn¹trz piekarnika

delikatne i równomierne ciep³o. Ten program jest

przeznaczony do pieczenia delikatnych potraw (na

przyk³ad ciast dro¿d¿owych), przygotowywania

filetów mignon na trzech poziomach jednoczenie.

Program FAST COOKING

W³¹czaj¹ siê elementy grzejne i uruchamia siê

wentylator, zapewniaj¹c utrzymywanie sta³ej i

równomiernej temperatury w piekarniku.

Program nie wymaga wstêpnego nagrzewania.

Program ten jest szczególnie wskazany do

szybkiego pieczenia potraw wstêpnie

przygotowanych (mro¿onych lub podgotowanych).

Program MULTIPIECZENIE

W³¹czaj¹ siê wszystkie elementy grzejne (górny,

dolny oraz obwodowe) i uruchamia siê wentylator.

Poniewa¿ temperatura jest równomierna w ca³ym

piekarniku, powietrze piecze i przyrumienia ¿ywnoæ

w sposób równomierny. Jednoczenie mo¿na u¿ywaæ

maksymalnie dwóch poziomów.

Program PIEKARNIK DO PIZZY

W³¹czaj¹ siê dolny i obwodowy element grzejny oraz

uruchamia siê wentylator. To po³¹czenie umo¿liwia

szybkie nagrzanie piekarnika z silnym dop³ywem

ciep³a, zw³aszcza od do³u. W przypadku, gdy

wykorzystuje siê wiêcej ni¿ jeden poziom

równoczenie, konieczna jest ich zamiana miejscami

w po³owie pieczenia.

Program GRILL

Uruchamia siê centralna czêæ górnego elementu

grzewczego oraz ro¿en (jeli jest w danym modelu).

Wysoka temperatura skierowana bezporednio na

grill jest zalecana dla potraw wymagaj¹cych wysokiej

temperatury na powierzchni (befsztyki wo³owe i

cielêce, polêdwica, antrykot). Jest to program o

umiarkowanym zu¿yciu energii, idealny do pieczenia

niewielkich potraw. Umieciæ potrawê na rodku

rusztu, gdy¿ umieszczona w naro¿nikach nie

zosta³aby upieczona.

Program ZAPIEKANKA

W³¹cza siê górny element grzejny i uruchamia siê

wentylator oraz ro¿en (jeli jest w danym modelu).

£¹czy wymuszon¹ cyrkulacjê powietrza wewn¹trz

piekarnika z jednokierunkowym promieniowaniem

cieplnym. Zapobiega to przypaleniu powierzchni

potraw, zwiêkszaj¹c moc penetracji cieplnej.

 Pieczenia GRILL oraz ZAPIEKANKA powinny byæ

wykonywane przy zamkniêtych drzwiczkach.

Ro¿en (tylko w niektórych modelach)

Aby uruchomiæ ro¿en

(patrz rysunek) nale¿y

postêpowaæ w nastêpuj¹cy

sposób:

1. umieciæ brytfannê w pozycji 1;

2. umieciæ uchwyt ro¿na w pozycji 3, a nastêpnie

umieciæ ro¿en w odpowiednim otworze

znajduj¹cym siê w tylnej ciance piekarnika;

3. uruchomiæ ro¿en, wybieraj¹c pokrêt³em

PROGRAMY

lub ;

 Kiedy program

jest uruchomiony, otwarcie

drzwiczek powoduje zatrzymanie ro¿na.

Praktyczne porady dotycz¹ce pieczenia

 Podczas pieczenia z wentylatorem nie u¿ywaæ

poziomów 1 i 5: gor¹ce powietrze dzia³a na nie

bezporednio, co mog³oby spowodowaæ przypalenie

delikatnych potraw.

MULTIPIECZENIE

 Stosowaæ pó³ki na pozycjach 2 i 4, a na pozycji 2

umieszczaæ potrawy wymagaj¹ce wy¿szej

temperatury.

 Ustawiaæ brytfannê na dole, a ruszt na górze.

GRILL

 Podczas pieczenia GRILL umieszczaæ ruszt w

po³o¿eniu 5, a brytfannê w po³o¿eniu 1 w celu

zebrania pozosta³oci po pieczeniu (sosy i/lub

t³uszcze). Podczas pieczenia ZAPIEKANKA

ustawiaæ ruszt w po³o¿eniu 2 lub 3, a brytfannê w

po³o¿eniu 1 w celu zebrania pozosta³oci po

pieczeniu.

 Zaleca siê ustawiaæ poziom energii na wartoæ

maksymaln¹. Nie nale¿y siê niepokoiæ, jeli górny

grzejnik nie bêdzie stale w³¹czony: jego prac¹

steruje termostat;

PIEKARNIK DO PIZZY

 Stosowaæ blachê z lekkiego aluminium, stawiaj¹c

j¹ na ruszcie znajduj¹cym siê w wyposa¿eniu

kuchenki. Korzystanie z brytfanny wyd³u¿a czas

pieczenia, a pizza rzadko jest chrupi¹ca.

 W przypadku pizzy z wieloma dodatkami, zaleca

siê dodanie mozzarelli dopiero w po³owie

pieczenia.

Programowanie pieczenia z u¿yciem

programatora elektronicznego

Ustawianie zegara

Po pod³¹czeniu do sieci elektrycznej lub po black-out

na wywietlaczu pojawiaj¹ siê pulsuj¹ce cyfry 0.00.

W celu ustawienia godziny:

1. wcisn¹æ jednoczenie przyciski CZAS TRWANIA

PIECZENIA

oraz KONIEC PIECZENIA

;

2. w ci¹gu 4 sekund ustawiæ dok³adn¹ godzinê

wciskaj¹c przyciski

oraz

)

Za pomoc¹ przycisku

zwiêksza siê wartoæ czasu; za pomoc¹

przycisku

)

zmniejsza siê j¹ .

Po ustawieniu godziny programator przechodzi

automatycznie w tryb rêczny.

Ustawianie minutnika

Przy pomocy minutnika mo¿na ustawiæ odliczanie

wsteczne, po którego zakoñczeniu emitowany jest

sygna³ akustyczny.

W celu ustawienia minutnika:

1. wcisn¹æ przycisk MINUTNIK

. Na wywietlaczu pojawia

siê: N.

2. wcisn¹æ przyciski

oraz

)

w celu ustawienia

¿¹danego czasu;

3. po zwolnieniu przycisków rozpoczyna siê

odliczanie wsteczne, a na wywietlaczu pojawia siê

aktualna godzina: R

4. po up³ywie ustawionego czasu emitowany jest

sygna³ akustyczny, który mo¿na wy³¹czyæ wciskaj¹c

dowolny przycisk (z wyj¹tkiem przycisków

)

symbol

wy³¹cza siê.

 Minutnik nie kontroluje w³¹czania i wy³¹czania

piekarnika.

Regulowanie g³onoci sygna³u akustycznego

Po dokonaniu wyboru i zatwierdzeniu ustawieñ

zegara, przy pomocy przycisku

)

, mo¿liwe jest

wyregulowanie g³onoci sygna³u akustycznego.

Programowanie czasu trwania pieczenia z

opónionym rozpoczêciem

Przede wszystkim nale¿y wybraæ ¿¹dany program

pieczenia oraz temperaturê, pos³uguj¹c siê

pokrêt³ami PROGRAMY i TERMOSTAT piekarnika.

Teraz mo¿liwe jest zaprogramowanie czasu trwania

pieczenia:

1. wcisn¹æ przycisk CZAS TRWANIA PIECZENIA

;

2. w ci¹gu 4 sekund ustawiæ ¿¹dany czas trwania

pieczenia wciskaj¹c przyciski

oraz

)

. Jeli, na

przyk³ad,czas trwania pieczenia zostanie

zaprogramowany na 30 minut, na wywietlaczu pojawi

siê: N

3. po zwolnieniu przycisków i up³ywie 4 sekund na

wywietlaczu ponownie pojawi siê aktualny czas (na

przyk³ad 10.00) wraz z symbolem

oraz liter¹ A

(AUTO):

Nastêpnie nale¿y zaprogramowaæ godzinê zakoñczenia

pieczenia:

4. wcisn¹æ przycisk KONIEC PIECZENIA

;

5. w ci¹gu 4 sekund ustawiæ ¿¹dan¹ godzinê zakoñczenia

pieczenia wciskaj¹c przyciski

oraz

)

. Jeli, na

przyk³ad, zamierza siê zakoñczyæ pieczenie o godzinie

13.00, na wywietlaczu pojawi siê: O

6. po zwolnieniu przycisków i up³ywie 4 sekund na

wywietlaczu ponownie pojawia siê aktualny czas

(na przyk³ad 10.00) wraz z liter¹ A (AUTO): P

Zgodnie z przedstawionym przyk³adem, piekarnik

w³¹czy siê automatycznie o godzinie 12.30 i

zakoñczy pracê po 30 minutach, o godzinie 13.00.

Strona jest ładowana ...

Indesit CE6VP6 (A) U instrukcja

Marka: Indesit

Model: CE6VP6 (A) U

Kategoria: Piekarniki

Typ: instrukcja

ściągnij PDF

raport

w innych językach

English: Indesit CE6VP6 (A) U User guide

Indesit CE6VP6 (A) U instrukcja

Indesit CE6VP6 (A) U instrukcja

w innych językach

Powiązane dokumenty

Inne dokumenty