LG WFT85B30EHT Instrukcja obsługi

Washing Machine

OWNER’S MANUAL

Please read this manual carefully before operating your set.

Retain it for future reference.

Record model name and serial number of the set.

Quote this information to your dealer when you require service.

P/No. : 3828EY3052G

MODEL :

WFT85B30(31)D(E)C(D,E,F,P,H)(T)

WFT75A30(31)D(E)C(D,E,F,P,H)(T)

WFT75B30(31)D(E)C(D,E,F,P,H)(T)

roduct Features

P

FUZZY logic control

●

A built-in load sensor automatically detects the laundry load and a

microprocessor optimizes washing conditions such as ideal WATER LEVEL

and washing time.

●

Advanced technology is built into the Electronic Control System which

ensures the best washing result.

Turbo drum washing (option)

●

When "Punch + 3" washing wings turn, the washing

tub turns in the opposite direction. This makes the both

sides current of water which improve wash-

performance by rubbing clothes strongly.

Applied models : WFT

Washer doesn't operate while the lid is open. If the lid is open during the wash,

rinse or spin cycles, the operation stops for safety.

3 Step washing

●

3 step washing makes the best washing performance with low tangling.

sensors

●

The sensor automatically detects the quantity of a Detergent put by a user and the

temperature and the quality of water to make the best washing algorithm for

washing and rinsing, which can give the best washing effect.

START

WASHING

AUTO

POWER

OFF

SENSING

Laundry Sensor

Water Level Sensor

SETTING

Optimum

Washing

Condition

Rubbing

Rubbing and

Shaking

Shaking and

Disentangling

ATTENTION

:

Be sure to remove the unit from the carton base,

otherwise the machine will not be able to operate properly.

C

ontents

Introduction

Before Starting to Wash

Washing Programs

Additional Function

Program

Installation

Care and Maintenance

Troubleshooting

Terms of Warranty

Specification

Safety Information

Identification of Parts

Function Information

Preparation Before Washing

Use of Water, Detergent, Bleach and Softener

Special Guide for Stain Removal

Function of each Button

FUZZY Wash (Normal Wash)

ECONOMY Wash

JEAN Wash

WOOL Wash

DELICATE

SPEEDY SOAK Wash

FAVORITE Wash

SILENT

TUB CLEAN

DELAY START (RESERVATION) Wash

Option Washing

Other Useful Functions

Placing and Leveling

Connecting Water Supply Hose

Connecting Drain Hose

Grounding Method

Cleaning and Maintenance

Common washing problems

Troubleshooting

Terms of Warranty

Specification

4

5

6

7

8

11

12

14

16

17

18

19

20

21

22

23

24

27

28

29

31

32

33

34

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your washer

properly. Just a little preventive care on your part can save you a great deal of time and

money over the life of your washer. You will find many answers to common problems

in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you

may not need to call for service at all.

afety Information

S

4

Introduction

Read and follow this safety information carefully.

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, personal injury, or loss of life.

Save these instructions.

WARNING!

WATER HEATER

SAFETY

PROPER

INSTALLATION

YOUR

LAUNDRY

AREA

WHEN USING

THE WASHER

WHEN NOT IN

USE

• Under certain conditions hydrogen gas may be produced in a water heater that has not been

used for two weeks or more. Hydrogen gas can be explosive under these circumstances. If the

HOT water has not been used for two weeks or more, prevent the possibility of damage or

injury by turning on all HOT water faucets and allowing them to run for several minutes. Do

this before using any electrical appliance which is connected to the HOT water system. This

simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do

not smoke or use an open flame or appliance during this process.

• The base opening must not be obstructed by carpeting when the washing machine is installed on

a carpeted floor.

• Install or store where it will not be exposed to temperatures below freezing or exposed to the

weather.

• Properly ground washer to conform with all governing codes and ordinances. Follow details in

Installation Instructions.

• Must be positioned so that the plug is accessible.

• Keep the area underneath and around your appliances free of combustible materials such as lint,

paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is used by or near children. Do not allow children

to play on, with, or inside this or any other appliance.

• Use this appliance only for its intended purpose as described in this Owner's Manual.

• Never reach into washer while it is moving. Wait until the machine has completely stopped

before opening the lid.

• Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing

different chemicals can produce a toxic gas which may cause death.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with

combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents,

kerosene, etc.) which may ignite or explode. Do not add these substances to the wash water. Do

not use or place these substances around your washer or dryer during operation.

• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully

follow the garment manufacturer's wash and care instructions.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or

disconnect the washer at the household distribution panel by removing the fuse or switching off

the circuit breaker before attempting any maintenance or cleaning.

NOTE: Pressing Power button to turn off does NOT disconnect the appliance

from the power supply.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a damaged cord or plug.

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break

or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5

years.

• Before discarding a washer, or removing it from service, remove the washer lid to prevent

children from hiding inside.

• Do not attempt to repair or replace any part of this appliance unless specifically recommended in

this Owner's Manual, or in published user-repair instructions that you understand and have the

skills to carry out.

• Do not tamper with controls.

I

dentification of Parts

5

Introduction

WATER SUPPLY

HOSE

Make sure the water

does not leak.

POWDER DETERGENT

BOX FOR DELAYED

WASHING

INLET HOLE FOR

BLEACH

Softner will automatically

flow into the tub.

SOFTENER

INLET

TUB

BASE

ADJUSTABLE LEGS

Use to level the washing

machine for correct balance

& spin operation.

Check if the drain hose

is hung up before

operating the

washing machine.

DRAIN HOSE

for pump model

DRAIN HOSE

for non pump model

POWER PLUG

If the supply cord is

damaged, it must be

replaced by the

manufacturer

or its service agents

or similarly qualified

person in order to

avoid a hazard.

LINT FILTER

Clean regularly to stop

linting on the clothes

load.

START/PAUSE

BUTTON

Use to start or stop the

washing machine

temporarily.

Drain hose Anti-rat cover (option)

Water supply hoses

or

1 Each for COLD and

HOT water

Body

Accessories

Part can be different according to the model.

Note

unction Information

F

6

Introduction

Our machine provides various washing methods which suits various conditions and

types of laundry.

FUZZY(Normal) Wash

JEAN Wash

WOOL Wash

ECONOMY Wash

SPEEDY SOAK Wash

DELAY START Wash

OPTION WASH

Use this Program for everyday washing e.g. sheets, towels, T-shirts.

(refer to page 14)

DELICATE Wash

Use this program to wash DELICATE and washable laundries.

(refer to page 14)

FAVORITE Wash

This setting allows you to store your FAVORITE wash conditions in the normal cycle memory.

(refer to page 17)

SILENT Wash

Use this program to wash quietly at night.

(refer to page 18)

Use this Program for heavily soiled durable garments e.g. overalls, jeans.

Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 14)

Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 14)

The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.

Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them

• Before washing your woolens check the care label for the washing instructions.

• When washing woolens use a mild Detergent recommended for washing wool.

• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.

• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.

(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)

Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.

(Ensure that the whole article is suitable for machine washing and not just the backing material.)

You may wish to handwash these articles and place them in the machine to spin dry.

ECONOMY wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time.

(refer to page 14)

SPEEDY SOAK Wash is designed to maximize washing performance and can be selected to wash heavily

soiled laundry with FUZZY or Jean Program.

(refer to page 16)

DELAY START Wash is used to delay the finishing time of the operation.

The number of hours to be delayed can be set by the user accordingly.

(refer to page 20)

When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,

SPEEDY SOAK/WASH/RINSE/SPIN.

(refer to page 21)

WASH OPTION

One or more WASH OPTIONS can be selected for FUZZY and JEAN washing program.

(refer to page 22)

TUB CLEAN

Use this program to clean the inside of washing machine especially Inner tub & Outer tub .

(refer to page 19)

Washing according to the condition of laundry

Other washing method

Different types of laundry washing

P

reparation Before Washing

7

Before Starting to Wash

• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,

pens, coins, and keys can damage both your washer and your clothes.

• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.

• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.

• Pretreat any dirt and stains.

• Make sure the clothes are washable in water.

• Check the washing instructions.

• Remove tissue in pockets.

To get the best results, different fabrics need to be washed in different ways.

• SOIL (Heavy, Normal, Light)

Separate clothes according to the type and amount of soil.

• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.

• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.

Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers

Lint Collectors Synthetics, Corduroy, Permanent Press, Socks

WIRE

Sorting

Check before Loading

* Look for a care label on your clothes. This will tell you about the fabric content of your garment

and how it should be washed.

Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

Care Labels

Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent

tangling during washing.

Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.

Nylon net is not supplied by LG.

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and

wash them in a small amount of water. If the laundry floats during the wash cycle, it may

become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Light and Large-sized clothing

Long laundry items

Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).

Load Size

The WATER LEVEL should just cover the clothes. Adjust the load size

accordingly. Loosely load clothes no higher than the top row of holes in the

washer tub. To add items after washer has started, press Start button and

submerge additional items. Close the lid and press Start button again to restart.

Loading

• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.

Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

• Use a pretreat soil and stain remover.

Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.

(For more detail refer to page11)

Pretreatment on stains or heavy soil

Fire Hazard

Never place items in the washer that are

dampened with gasoline or other flammable

fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type

of oil on it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING

8

Before Starting to Wash

se of Water, Detergent, Bleach and Softener

U

• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.

We recommend temperatures of:

- HOT 49~60°C…(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items.

- WARM 29~40°C…(85-105˚F) Most items

- COLD* 18~24°C…(65-75˚F) Only very bright colors with light soil.

• When washing in COLD water additional steps may be needed:

- Adjust Detergent amount and pre-dissolve Detergent in WARM water

- Pretreat spots and stains

- Soak heavily soiled items

- Use appropriate bleach

* Temperature below 18°C…(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.

In addition, Detergent manufactures and care labels define COLD water as 26~29°C…(80-85˚F).

If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean

effectively.

Using Detergent

Detergent

Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.

Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.

Choosing the right Detergent

We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or

granulated soap powders should not be used in your washing machine. When washing woolens

remember to use Detergent suitable for washing woolens.

Water Temperature

Using Water

• The machine sets the appropriate temperature automatically according to the wash program .

• You can change the Water Temperature by pressing the WATER TEMP. button. (refer to page 12)

• This machine detects the quantity of laundry automatically, then sets the WATER

LEVEL and proper amount of Detergent.

• When you select a wash program, the WATER LEVEL and amount of Detergent

(to be used) will be shown on the control panel.

• The following table shows the amount of water.

• When the WATER LEVEL is automatically detected, it may differ depending on the quantity of laundry

even though the same WATER LEVEL is indicated on the control panel.

• The amount of a cup in the diagram is about 40g for concentrated Detergent.

Amount of WATER LEVEL

Attention

If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown

or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be

necessary for severe cases.

9

Before Starting to Wash

Using Detergent

How much Detergent

When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be

shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent.

The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work

cloches may need more Detergent, while bath towels usually need less.).

For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.

Note: To check you are using the correct amount of Detergent, lift the lid of your machine about half-

way through the wash. There should be a thin layer of foam over the surface of the water. Lots of

foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough

Detergent has been used; soil and lint can settle back on the clothes or the washing machine.

If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause

environmental pollution, so use it accordingly.

D nde

deposita el

detergente

Dispensador de detergente en polvo.

Adding the Detergent

Open the Detergent dispenser and deposit the appropriate

amount of Detergent

where you deposit the Detergent

Powder Detergent dispenser.

Some Detergents MUST be fully dissolved before

adding to your machine to get the best wash results.

Check the instructions on the Detergent packet.

If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water

before being added to WARM or HOT water for the actual wash.

Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance.

Where you

deposit the

Detergent

Powder Detergent Box

( )

• Check clothing care label for special instructions and separate the

laundry to be bleached

• Dilute liquid chlorine bleach.

• Measure the recommended amount of liquid bleach carefully

following instructions on the bottle.

• Before starting the washer, pour measured amount of bleach directly

into bleach dispenser. Avoid splashing or overfilling. Powdered

bleach should be mixed with water before pouring.

Using Liquid Bleach

Bleach dispenser

( )

Attention

■ Never pour undiluted liquid bleach directly onto clothes or into the wash basket.

This may cause change of color or damage the laundry.

■ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can reduce

a toxic gas which may cause death.

■ Do not pour powdered bleach into bleach dispenser.

se of Water, Detergent, Bleach and Softener

U

10

Before Starting to Wash

Using Fabric Softener

If you wish to use fabric softener we recommend

Attention

■ Do not mix with Detergent or bleach.

■ Never pour fabric softener directly on clothes. It may stain them.

■ Do not stop the washer during the first spin for timely dispensing.

■ Option washing is not designed to be used with fabric softener dispenser.

• Dilute fabric softener with water.

Undiluted fabric softener may result in spots that look like oil

stains.

• Measure and add the recommended amount of fabric softener

into the compartment marked with this symbol( ).

Follow manufacturer’s direction.

 Fabric softener is automatically dispensed in the final rinse

with indication beep.

 If you want EXTRA RINSE, you must add fabric

softener manually when indication beep rings in the final

rinse. This maximize the fabric softener function.

• Do not overfill. The dispenser hold max 35mL.

Never add more than 35mL.

Overfilling can cause early dispensing of the fabric softener

which could result in stained clothes. A cup with a pouring spout will help you avoid spilling.

• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its

effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually

put during the time when the washer beeps several times before the final rinse. This function informing

correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric

softener has to be diluted with water before dispensed and never poured directly on clothes.

Scrud(Waxy Build up)

Softener dispenser ( )

or

Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener

comes into contact with Detergent. This build-up is not brought about by a fault in the machine.

If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant

smell in your washer.

• Using fabric softener sparingly.

• When filling the dispenser, do not splash or overfill.

• Clean dispenser as soon as the cycle is finished.

• Clean your machine regularly. (refer to page 19 or 30)

• Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or

HOT wash e.g. every 5th wash should be at least a warm one.

• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a

build-up.

S

pecial Guide for Stain Removal

11

Before Starting to Wash

• Remove stains promptly.

• Determine the kind of stain, then follow the recommended treatment in the stain

removal chart below.

• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from

granular Detergent and water.

• Use COLD water on unknown stains because HOT water can set stains.

• Check care label instructions for treatments to avoid on specific fabrics.

• Check for colorfastness by testing stain remover on an inside seam.

• Rinse and wash items after stain removal.

For successful stain removal:

Follow fabric care label

instructions

■

Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or

products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.

■

To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:

• Read and comply with all instructions on stain removal products.

• Keep stain removal products in their original labeled containers and out of children’s reach.

• Thoroughly wash any utensil used.

• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.

• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents

or other flammable or explosive substances because they give off vapors that could ignite or explode.

• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.

WARNING

Stain Removal

STAIN

Adhesive tape, chewing gum,

rubber cement

Baby formula, dairy products, egg

Beverages (coffee, tea, soda, juice,

alcoholic beverages)

Blood

Candle wax, crayon

Chocolate

Collar or cuff soil, cosmetics

Dye transfer on white fabric

Grass

Grease, oil, tar (butter, fats, salad

dressing, cooking oils, car grease,

motor oils)

Ink

Mildew, scorch

Mud

Mustard, tomato

Nail polish

Paint, varnish

Rust, brown or yellow

discoloration

Shoe polish

Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or

nonflammable dry cleaning fluid.

Use product containing enzymes to pretreat or soak stains.

Pretreat stain. Wash using COLD water and bleach safe for fabric.

Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using

bleach safe for fabric.

Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.

Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning

fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.

Pretreat with prewash stain remover or rub with bar soap.

Use packaged color remover. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.

Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply

nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash

using hottest water safe for fabric.

Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured

alcohol or nonflammable dry cleaning fluid.

Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly

mildewed fabrics may be permanently damaged.

Brush off dry mud. Pretreat or soak with product containing enzymes.

Pretreat with prewash stain remover. Wash using bleach safe for fabric.

May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.

Repeat, replacing paper towels frequently. Do not use on acetate fabrics.

WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,

OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.

For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and

nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.

LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with

prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach

safe for fabric.

TREATMENT

13

Before Starting to Wash

* Because the detecting ability of the sensor may be decreased by using it for a long time, periodically use

TUB CLEAN course to clean the tub. (refer to page 19)

* Even if the water level or the water temperature are changed by the user in FUZZY(Normal) Program,

the sensor will still work. The sensor algorithm may differ according to models.

* The control panel may differ according to different models.

TIME LEFT, DELAY START (RESERVATION), ALARM INDICATION

• Time left - During operation, the remaining time is indicated.

• DELAY START INDICATION (RESERVATION) - When

DELAY START (RESERVATION) program is selected, it

indicates the finishing time. (RES.=DELAY)

• Alarm indication -When an error occurs, an error message

appears to indicate the abnormality. For example, indicates

that the lid is open.

CHILD LOCK FUNCTION

• Use to lock or unlock the control

buttons to prevent settings from

being changed by a child.

To lock, push the PROCESS and

PROGRAM buttons

simultaneously and to unlock

push them one more time during

the washing process.

(refer to page 22)

START/ PAUSE BUTTON

• Use to start or pause the

washing process.

• Repeats start and pause by

pushing the button.

PROCESS BUTTON

• Use to select

SPEEDY SOAK,

Wash, Rinse and Spin

functions as desired.

AUTO OFF

(POWER) BUTTON

• Use to turn the power on or

off.

• Push again and power goes

on or off

• The power goes off

automatically about 10

seconds after the wash is

finished.

PROGRAM BUTTON

• Use for selecting wash program.

• This button allows you to select 4

different programs for different kinds of

laundry and dirtiness.

• program selections light up in sequence as

follows: FUZZY (NORMAL)

DELICATE ECONOMY JEAN

WOOL SILENT FAVORITE

TUB CLEAN FUZZY

(NORMAL)

etc. Select the desired program by

pressing the button.

PEEDY SOAK Wash

S

16

Washing Programs

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty.

SPEEDY SOAK mode can be used with FUZZY or JEAN program.

SPEEDY SOAK will not work in WOOL and

ECONOMY, DELICATE Program.

The WATER LEVEL and the amount of Detergent to be

used will be shown and water will be supplied.

Press the AUTO OFF (POWER) button to turn power on.

Press the PROGRAM button to select the washing program.

Add the laundry and press the START/PAUSE button.

When the wash program ends, the buzzer will ring for

10seconds before the Power goes off automatically.

Finish

Keep pressing the PROCESS button until the SPEEDY SOAK

light is on and then Wash, Rinse, Spin lights are on

simultaneously.

Until the washing process is completed, the SPEEDY SOAK

light is on.

The appropriate quantity of Detergent marked next to the

WATER LEVEL of WATER-DETERGENT.

Add the Detergent.

Water will be supplied for 2 minutes after the start of the

wash to supplement the absorbed water by the laundry.

Close the lid.

1

3

4

5

6

2

F

AVORITE Wash

17

Washing Programs

Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the

normal cycle memory and then recall it for use at a later time.

• Press the WATER TEMP. button to select wash Water

Temperature.

• Press the WATER LEVEL button to select

WATER LEVEL.

• Press the WASH OPTION to select WASH OPTION.

• Press the PROCESS button to select PROCESS(WASH,

RINSE, SPIN) respectively you want to store.

Press the AUTO OFF (POWER) button to turn power on.

Select the FAVORITE program.

Select your FAVORITE wash conditions.

Press the START/PAUSE button to store & start your FAVORITE wash cycle.

Power turns off automatically after wash.

1

2

3

4

Note

To recall your FAVORITE cycle.

1. Press POWER on.

2. Select the FAVORITE cycle by pressing the PROGRAM.

3. Press the START/PAUSE button. Then the wash cycle starts.

T

UB CLEAN

19

Additional Function Program

If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in

your washer.

Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact

with Detergent, and according to particular degree of dirtiness or quality of water to be use,

in these case, use this program to clean inner tub and outer tub.

Press the POWER button to turn power on.

Press the PROGRAM button to select the TUB CLEAN program.

After 10 minutes of water supplement. Add the oxygenated bleach (about 300m ).

Press the START/PAUSE button.

Close the lid.

1

3

4

5

2

Note

• Before using this program remove lint inside lint filter.

• When using this program, do not place any laundry inside tub.

• This program takes about 3 hours to be completed.

• After using this program, remove dirt inside filter.

• After finishing this program, open the lid of wash to remove irritant odor.

• Do not pour bleach into the tub directly. It might cause damage the tub.

• Do not leave diluted oxygenated bleach inside tub for long time.

It rusts the tub must drain the remained diluted oxygenated water out.

• Use this program once for every month.

• Do not use this program repeatedly.

Ex-Large WATER LEVEL is set automatically.

• When the lid is open the machine will not operate, and an

alarm signal will remind you to close the lid.

• Left time is displayed.

• Do not use Detergent box.

• Do not place any laundry inside tub.

ELAY START (RESERVATION) Wash

D

20

Additional Function Program

3

DELAY START (RESERVATION) Wash is used to delay the finishing time of the

operation. The hours to be delayed can be set by the user accordingly.

The time on the display is the finishing time , not the start time.

When you press the START/PAUSE button the light will

blink.

Select the program for laundry on the Control panel.

This program will not work in WOOL and DELICATE

Program.

How to set the delay time.

Example : It' 7 a.m. now. If you'd like your wash to finish at 9

p.m. set the time as in the figure below.

When you push the button the reservation time changes

3  4 5 ...12  14  16 ... 48  3 repeatedly.

Press the POWER button to turn power on.

Press the PROGRAM button to select the washing program.

Add the laundry and press the START/PAUSE button.

Press the DELAY START (RESERVATION) button to set the time when the

delayed washing is to be completed.

The appropriate quantity of Detergent marked next to the

WATER LEVEL of WATER DETERGENT.

When the lid is open the machine will not operate, and an

alarm signal will remind you to close the lid

Add the Detergent.

Water will be supplied for 2 minutes after the start of the

wash to supplement the water the laundry has absorbed.

Close the lid.

The washing will be finished according to the delayed time.

To select washing program, spinning time, WATER LEVEL or HOT/COLD manually, press the DELAY

START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.

Finish

When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the

spinning program . (The laundry will be wrinkled if left for a long time after spinning.)

Note

If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.

1

2

4

5

6

(RES.=DELAY)

Strona jest ładowana ...

LG WFT85B30EHT Instrukcja obsługi

LG WFT85B30EHT Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty