Classic Exhibits VK-2914 Setup Instructions

Classic Exhibits
Marka
Classic Exhibits
Model
VK-2914
Typ
Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2914 - General Layout
Plan View
10’
20’
www.classicexhibits.com
Step 2
Page 2 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 3
Page 3 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2914 - Backwall Section Identication
SECTIONS IDENTIFICATION
Assemble Sections A & B separately then connect with center extrusions.
SEC. A
IN RED
SEC. B
IN GREEN
www.classicexhibits.com
Step 1
Page 1 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2914 - Backwall Assembly - Section A
1
Plan View
2
2
3
3
45
8
9
9
10
10
12
12
13
11
Plan View
8
**
*
*
Attach graphics
to velcro on back of
assembled backwall
Velcro:
Back/Top Edge Velcro:
Back/Top Edge
Velcro:
Back/Bottom Edge
Velcro:
Back/Bottom Edge
Item
1
2
3
4
5
8
9
10
11
12
13
Description
Oval Base Plate
83.75”h Square Vertical Extrusion
83.75”h Square Vertical Extrusion
84”h Square Vertical Extrusion
84”h Vertical Extrusion
83.75”h Angled Vertical Extrusion
83.75”h Angled Vertical Extrusion
26.9449” Curved Horizontal Extrusion
29.7770”w Horizontal Extrusion
26.9449” Curved Horizontal Extrusion
29.7770”w Horizontal Extrusion
Qty.
2
1
1
1
1
1
1
2
1
2
1
**Note: Keep vertical
extrusions [2 & 8] and [9 & 3]
assembled when shipping.
Steps:
1) Connect base plates [1] to vertical extrusion [2].
2) Attach angled vertical extrusions [8 & 9] to verticals [2 & 3].
Refer to
V10 Pressure Screw Attachment
detail.
3) Attach upper and lower curved horizontal extrusions [10 & 12] and
extrusions [11 & 13] between verticals [2, 4, 5, & 3].
NOTE: Velcro is on backside of frame.
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
V10
V10 Pressure
Screw Attachment
Slide V10 pressure
screw between grooves
of extrusions. Tighten
setscrew to secure
pressure in place.
*
SECTION A ASSEMBLY
www.classicexhibits.com
Step 2
Page 2 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2914 - Backwall Assembly - Section B
1
Plan View
3a
3a
2a
2a
45
8
9
9
10
10
12
12
13
11
Plan View
8
**
*
*
Attach graphics
to velcro on back of
assembled backwall
Velcro:
Back/Top Edge Velcro:
Back/Top Edge
Velcro:
Back/Bottom Edge
Velcro:
Back/Bottom Edge
Item
1
2a
3a
4
5
8
9
10
11
12
13
Description
Oval Base Plate
83.75”h Square Vertical Extrusion
83.75”h Square Vertical Extrusion
84”h Square Vertical Extrusion
84”h Vertical Extrusion
83.75”h Angled Vertical Extrusion
83.75”h Angled Vertical Extrusion
26.9449” Curved Horizontal Extrusion
29.7770”w Horizontal Extrusion
26.9449” Curved Horizontal Extrusion
29.7770”w Horizontal Extrusion
Qty.
1
1
1
1
1
1
1
2
1
2
1
**Note: Keep vertical
extrusions [2 & 8] and [9 & 3]
assembled when shipping.
Steps:
1) Connect base plates [1] to vertical extrusions [2a].
2) Attach angled vertical extrusions [8 & 9] to verticals [2a & 3a].
Refer to
V10 Pressure Screw Attachment
detail.
3) Attach upper and lower curved horizontal extrusions [10 & 12] and
extrusions [11 & 13] between verticals [2a, 4, 5, & 3a].
NOTE: Velcro is on backside of frame.
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
V10
V10 Pressure
Screw Attachment
Slide V10 pressure
screw between grooves
of extrusions. Tighten
setscrew to secure
pressure in place.
*
SECTION B ASSEMBLY
www.classicexhibits.com
Step 3
Page 3 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2914 - Backwall Assembly - Sections Assembly
Item
11a
13a
14
Description
29.5”w Z45 Horizontal Extrusion
29.5”w Z45 Horizontal Extrusion
32.5”w Monitor Mounting Plate
Qty.
1
1
1
Steps:
1) Connect horizontal extrusions [11a &13a ]
between verticals [3 & 3a].
NOTE: This connects Sections A & B together.
2) Attach monitor mounting plate [14] to face of
verticals [3 & 3a].
See Monitor Mounting Plate Attachment detail.
3) Apply Graphics to backside of assembled backwall.
NOTE: Velcro is on backside of frame.
SECTIONS ASSEMBLY
SEC. A
SEC. B
Attach graphics
to velcro on back of
assembled backwall
Velcro:
Back/Top Edge
Velcro:
Back/Bottom Edge
3a
3
13a
14
FRONT VIEW
11a
Monitor Mounting
Plate Attachment
Attach mounting plate
to verticals as shown.
Slide mounting connector pieces
into groove of extrusion. Tighten
setscrew to secure in place.
Setscrew
Setscrew
*
*
**
*
www.classicexhibits.com
Step 4
Page 4 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
VK-2914 - Backwall Counter & Shelves
Item
6
7
15
16
17
17A
Description
38” Round Vertical Extrusion
38” Round Vertical Extrusion
12.5” Horizontal Extrusion
28.3203” Curved Extrusion
38” Angled Vertical Extrusion w/ Door Stopper
38” Angled Vertical Extrusion w/ Door Hinges
Qty.
1
1
2
2
1
1
6
15
15
15
16
16
Door
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Shelf
Door
Hinges
Infill
Infill
15
14
17A
17 7
**Note: Keep vertical
extrusions [6 & 17] and [7 & 17A]
assembled when shipping.
*
**
*
*
V10
V10 Pressure
Screw Attachment
Slide V10 pressure
screw between grooves
of extrusions. Tighten
setscrew to secure.
*
617
Plan View
7
17A
Plan View
Steps Cont’d:
4) Attach monitor mount to horizontal plate [14].
See
Monitor Mount Attachment
detail.
5) Attach shelf supports to inside of backwall counter.
6) Place internal shelf on top of shelf supports.
7) Place Counter top on assembled kiosk base.
8) Connect shelves to clips on vertical extrusions.
Steps:
1) Attach angled vertical extrusions [17 & 17A] to verticals
[6 & 7]. See
V10 Pressure Screw Attachment
detail.
2) Attach upper and lower horizontal extrusions [15] between
verticals [6 & 4] and [7 & 5]. Note: Place infills between
horizontal and vertical extrusions as shown.
3) Attach upper and lower horizontal curved extrusions [16]
between vertical extrusions [17 & 17A]. Note: Attach door
between horizontal and vertical extrusions as shown.
See
Door Attachment
detail.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
*
*
*
Monitor Mount
Attachment
Connect mounting plate
to verticals as shown.
Attach Monitor Mount
to plate using bolts
and wing nuts
*
Counter Top
Shelf
(4) Shelf
Supports
www.classicexhibits.com
Step 5
Page 5 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
VK-2914 - Ceiling and Header Assembly
Item
18
18A
19
Description
78” Header Horizontal Extrusion
78” Header Horizontal Extrusion with holes and bolts
5.823” Header Horizontal Extrusion
QTY. 2
Qty.
1
1
2
18
19
19
18A
Header Infill
Header
Ceiling
Ceiling
Puck Light
Puck Light
Steps:
1) Attach vertical extrusions [19] between horizontal extrusions [18 & 18A].
Note: Place infills between horizontal and vertical extrusions as shown.
2) Attach header assembly to ceiling using bolts and wing nuts as shown.
3) Attach puck lights from under into holes at bottom of ceiling as shown.
Note: Light bulb must face down.
Steps #1
Steps #2
Steps #3
Wing
Nuts
Bolt
Bolt
Bolt
Bolt
Wing
Nuts
www.classicexhibits.com
Step 6
Page 6 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Steps:
1) Attach Ceiling/Header to top of assembly.
2) Connect the graphic wings to the outter verticals.
VK-2914 - Attachments
www.classicexhibits.com
Step 7
Page 7 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
VK-2914 - Pedestal Workstation
23
Shelf
Literature
Pocket
Counter Top
Monitor
Mount Plate
Shelf
22
24
**Note: Keep A10 Clamps
assembled with vertical
extrusion when shipping.
20
Infill
21
Item
20
21
22
23
24
Description
Round Base Plate
38.125”h Left Diagonal Extrusion w/ A10 Clamps Attached
38.125”h Right Diagonal Extrusion w/ A10 Clamps Attached
60” Square Vertical Extrusion
16” Horizontal Extrusion w/ Angle Cut Both Ends
Qty.
1
1
1
1
1
Steps:
1) Attach diagonal extrusions [21 & 22] and square vertical extrusion [23] to round base plate [20].
2) Place infill into groove between diagonal extrusions [21 & 22].
3) Attach horizontal extrusion [24] between diagonal extrusions [21 & 22] at top.
4) Place counter top atop horizontal support [24] and attach to vertical extrusion [23].
Refer to
Counter Attachment
detail.
5) Attach shelves to diagonal extrusions [21 & 22] with A10 Clamps. **
Refer to
Example of A10 Clamp Attachment
detail.
6) Attach literature pockets to diagonal extrusions [21 & 22].
Refer to
Literature Rack Attachment
detail.
7) Attach monitor mount plate to vertical extrusion [23].
Refer to
Monitor Mount Attachment
detail.
QTY. 2
After setting counter on horizontal
support, put washer on thumbscrew,
and attach thumbscrew through counter
to vertical extrusion as shown.
Counter Attachment
Washer
Thumbscrew
*
*
*
*
*
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
*
**
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
VK-2914 - Crate Packing
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Crate Packing
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Classic Exhibits VK-2914 Setup Instructions

Classic Exhibits
Marka
Classic Exhibits
Model
VK-2914
Typ
Setup Instructions
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty