Parkside PTSS 1200 C2 Instrukcja obsługi

SCIE PLONGEANTE

Traduction des instructions d’origine

TAUCHSÄGE

Originalbetriebsanleitung

PLUNGE SAW

Translation of the original instructions

PONORNÁ PILA S LIŠTOU

Překlad originálního provozního návodu

INSTEEKZAAG

Vertaling van de originele gebruiksaanwijzing

PONORNÁ PÍLA

Preklad originálneho návodu na obsluhu

PIŁA WGŁĘBNA

Tłumaczenie oryginalnej instrukcji obsługi

SIERRA DE INMERSIÓN

Traducción del manual de instrucciones original

DYKSAV

Oversættelse af den originale driftsvejledning

PLUNGE SAW / TAUCHSÄGE / SCIE PLONGEANTE

PTSS 1200 C2

IAN 361911_2007

GB Translation of the original instructions Page 1

DE Originalbetriebsanleitung Seite 15

FR Traduction des instructions d’origine Page 29

NL Vertaling van de originele gebruiksaanwijzing Pagina 45

CZ Překlad originálního provozního návodu Strana 59

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 73

SK Preklad originálneho návodu na obsluhu Strana 87

ES Traducción del manual de instrucciones original Página 101

DK Oversættelse af den originale driftsvejledning Side 115

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l‘appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas

las funciones del dispositivo.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

A B

C

8a 9a

14a 14b

X

PTSS 1200 C2 GB│IE │ 1 ■

Contents

Introduction ............................................................2

Intended use ........................................................................2

Features ...........................................................................2

Package contents ....................................................................2

Technical speciﬁcations ...............................................................3

General power tool safety warnings .......................................4

1. Work area safety ..................................................................4

2. Electrical safety ...................................................................4

3. Personal safety ....................................................................4

4. Power tool use and care ............................................................5

5. Service ..........................................................................5

Appliance-speciﬁc safety instructions for hand-held circular saws ...............................6

Safety instructions for circular sawblades .................................................7

Before use .............................................................8

Fitting/changing the saw blade .........................................................8

Connecting the sawdust extractor .......................................................8

Checking blade guard functionality ......................................................8

Use ................................................................... 8

Switching on and oﬀ .................................................................8

Setting the cutting depth ...............................................................9

Setting the cutting angle (mitreangle) ....................................................9

Note the cut line .....................................................................9

Connecting the guide rails .............................................................9

Eccentric screws ....................................................................10

Sawing (without the guide rail) ........................................................10

Sawing (with the guide rail) ...........................................................10

Plunge cutting using the guide rail ......................................................11

Cleaning and maintenance ..............................................11

Disposal ..............................................................11

Kompernass Handels GmbH warranty ....................................12

Service ...............................................................13

Importer .............................................................13

Original declaration of conformity ........................................14

PTSS 1200 C2

■ 2 │ GB│IE

PLUNGE SAW PTSS1200C2

Introduction

Congratulations on the purchase of your new

appliance. You have chosen a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product,

please familiarise yourself with all the operating

and safety instructions. Use the product only as

described and for the range of applications speci-

ﬁed. Please also pass these operating instructions

on to any future owner.

Intended use

This circular saw (hereinafter "appliance" or

"machine") is designed for longitudinal, cross and

plunge cuts in ﬁrmly supported solid wood, chip

board, plastics and lightweight construction materials.

Working with metals is not permitted. This appli-

ance can be used with the provided guide rails–

exclusively for the cutting techniques described.

Any other use of or modiﬁcation to the appliance

is deemed to be improper and carries the risk of

serious personal injury. Not for commercial use.

Features

Safety lock-out

ON/OFF switch

Handle

Hex key (small)

Hex key (large)

Motor unit

Chip ejector adapter

Fine adjustment screws for 0° cutting angle

8a Fine adjustment screw for 45° cutting angle

Base plate

9a Cut line markings

Eccentric screw (2 x)

Adjustment wheel for cutting angle adjustment

(2 x)

Cutting depth adjustment

Cutting depth scale

Saw blade

14a Clamping screw/washer

14b Mounting cut-out

Additional handle

Cutting width marking

Chip ejector (rotatable)

Clamping lever for changing saw blades

Spindle lock

Groove for guide rails

Guide rail

Grub screws

Connector

X Flange (factory-ﬁtted)

Package contents

1 plunge saw

1 saw blade 165mm/24 teeth (pre-ﬁtted)

2 guide rails

1 connector

1 chip ejector adapter

2 hex keys

1 set of operating instructions

PTSS 1200 C2 GB│IE │ 3 ■

Technical speciﬁcations

Rated voltage 230 V ∼, 50 Hz (AC)

Rated power consumption 1200 W

Rated idle speed n0 5200 rpm

Saw blade holder Ø 20 mm

165mm Saw blade

diameter Ø 165 mm

Blade thickness 1.5 mm

Tooth size 2.6 mm

max. 65 mm

Max.

cutting depth 56 mm at a 90°

mitre angle

42 mm at a 45°

mitre angle

5 mm less when using

guide rails

Protection class II /

(double insulation)

Accessories 2 x guide rails

700 mm x 180 mm

Noise emission value

Noise measurement value determined in accord-

ance with EN 62841. The A-rated noise level of

the power tool is typically as follows:

Sound pressure level LPA = 89 dB (A)

Uncertainty KPA = 3 dB

Sound power level LWA = 100 dB (A)

Uncertainty KWA = 3 dB

Wear ear muﬀs!

Total vibration value

Total vibration values (vector total of three direc-

tions) determined in accordance with EN 62841:

Sawing wood ah,W = 1.3 m/s2

Uncertainty K = 1.5 m/s2

NOTE

► The vibration emission value and noise emis-

sion levels speciﬁed in these instructions have

been measured in accordance with the stand-

ardised testing procedure speciﬁed and can

be used to make equipment comparisons. The

speciﬁed vibration emission value and the

noise emission values can also be used to

make an initial load estimate.

WARNING!

► Depending on the manner in which the

power tool is being used and, in particular,

the kind of workpiece that is being worked,

the vibration and noise emission values can

deviate and may sometimes exceed the

values given in these instructions. Regular use

of the power tool in this way may cause the

user to underestimate the vibration. Try to

keep the vibration loads as low as possible.

Measures to reduce the vibration load are,

e.g. wearing gloves and limiting the working

time. Wherein all states of operation must be

included (e.g. times when the power tool is

switched oﬀ and times where the power tool

is switched on but running without load).

PTSS 1200 C2

■ 4 │ GB│IE

General power tool

safety warnings

WARNING!

►Read all safety warnings, instructions, illus-

trations and speciﬁcations provided with

this power tool. Failure to follow all instruc-

tions listed below may result in electric shock,

ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entan-

gled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

re duces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use

personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat

or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

PTSS 1200 C2 GB│IE │ 5 ■

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not allow yourself to get lulled into a false

sense of security and do not ignore the safety

rules for power tools, even if you are familiar

with the power tool after repeated use.

A careless action can cause severe injury within

a fraction of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool acci-

dentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and acces-

sory tools etc. in accordance with these

instructions, taking into account the working

conditions and the work to be performed.

Use of the power tool for operations diﬀerent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in

unexpected situations.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only original replacement

parts. This will ensure that the safety of the

power tool is maintained.

PTSS 1200 C2

■ 6 │ GB│IE

Appliance-speciﬁc safety instructions

for hand-held circular saws

Safety instructions for all saws

Sawing method

a) DANGER! Keep your hands clear of

the sawing area and the saw blade.

If you are holding the saw with both of

your hands, neither hand can be injured by the

saw blade.

b) Do not reach underneath the workpiece.

The blade guard cannot protect you from the

saw blade underneath the workpiece.

c) Set the cutting depth in accordance with the

thickness of the workpiece. The blade should

not extend more than one full tooth depth under

the workpiece.

d) Never hold the workpiece being sawn in your

hand or over your leg. Fasten the workpiece

onto a stable working surface. It is important

to fasten the workpiece securely to minimise the

danger of bodily contact, jamming of the saw

blade or loss of control.

e) Hold the power tool only by the insulated

handles when you are carrying out work in

which the accessory tool may come into

contact with concealed power cables. Contact

with a live wire will also make exposed metal

parts of the power tool live and could give the

operator an electric shock.

f) When making longitudinal cuts, always use a

rip fence or a straight edge guide. This will

improve the accuracy of your cut and reduce

the likelihood of the saw blade jamming.

g) Always use saw blades of the correct size

and with a suitable mounting hole (e.g.

square or round). Blades that do not match the

mounting hardware of the saw will run eccentri-

cally, causing loss of control.

h) Never use damaged or incorrect blade

washers or bolts. The saw blade washers and

screws have been specially designed to provide

optimum performance and operational safety

for your saw.

Additional safety instructions for all saws

Kickback - causes and corresponding safety

instructions

▯ A kickback is a sudden reaction caused as a

result of the saw blade catching, jamming or

being falsely aligned, causing the saw to jump

up uncontrollably and out of the workpiece in

the direction of the operator.

▯ If the saw blade catches or jams in a narrowing

saw cut, the blade can no longer rotate and the

power of the motor throws the saw back in the

direction of the operator.

▯ If the saw blade twists in the saw cut or

becomes misaligned, the teeth at the rear edge

of the saw blade can become caught in the

wood surface, causing the saw blade to jump

out of the cut and the saw to jump backwards in

the direction of the operator.

A kickback is caused by incorrect use or misuse of

the saw. This can be avoided by taking proper

precautions as given below.

a) Hold the saw ﬁrmly and position your arms so

that they can absorb the force of a kickback.

Always stand to the side of the saw blade

and never in line with it. If a kickback occurs,

the circular saw may jump backwards.

However, by taking appropriate precautions the

operator can control the kickback forces.

b) If the saw blade jams or you stop working,

switch the saw oﬀ and hold it steadily in the

workpiece until the saw blade has completely

stopped turning. Never attempt to remove the

saw from the workpiece or pull it backwards

while the saw blade is still moving as this

could lead to a kickback. Investigate what is

causing the blade to jam and take corrective

action.

c) If you want to restart a saw that is still in the

workpiece, centre the saw blade in the cut

and check to ensure that the teeth are not

caught anywhere in the workpiece. If the saw

blade catches it can jump out of the workpiece

or cause a kickback when the saw is restarted.

PTSS 1200 C2 GB│IE │ 7 ■

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels

or boards can bend under their own weight.

Panels/boards must be supported on both

sides: i.e. both in the vicinity of the saw cut

and also at the edge.

e) Do not use blunt or damaged saw blades.

Saw blades with blunt or misaligned teeth may

cause excessive friction if the saw cut is too

narrow, and this can cause a saw blade jam

and kickback.

f) Before sawing, ensure that the fastenings for

the cut depth and cut angle settings are tight-

ened. If the settings change while sawing, the

saw blade can jam and cause a kickback.

g) Be particularly careful when sawing in

existing walls or other obscured areas. The

inserted saw blade could get caught on hidden

objects and cause a kickback.

Additional safety instructions for all saws

with a splitting wedge

Function of the splitting wedge

a) Use the appropriate saw blade for the splitting

wedge. For the splitting wedge to work, the

saw blade's main blade must be thinner than

the splitting wedge and the tooth width must be

more than the splitting wedge thickness.

b) Adjust the splitting wedge as described in

these operating instructions. Incorrect spacing,

position and alignment can be the reason why

the splitting wedge does not eﬀectively prevent

a kickback.

d) The splitting wedge must be positioned in the

sawing gap before it will work. For short cuts,

the splitting wedge is ineﬀective in preventing

kickback.

e) Do not operate the saw with a bent splitting

wedge. Even a minor fault can slow down the

closing of the blade guard.

Supplementary notes

■ Do not use any grinding discs.

■ Use only saw blades with diameters corres-

ponding to the label on the saw.

■ Always use the right saw blade for the material

being worked.

■ Use only saw blades with a speed marking

that corresponds to or is higher than the speed

speciﬁed for the power tool.

■ Saw blades that are intended for use on wood

or similar materials must comply with EN 847-1.

■ Do not allow the teeth of the saw blade to

overheat.

■ When sawing plastic, avoid melting the plastic.

■ Wear a dust mask when sawing.

■ Only use recommended saw blades.

■ Always wear hearing protection!

Safety instructions for circular

sawblades

Wear protective gloves!

Wear a dust mask!

Wear protective goggles!

Wear ear muﬀs!

Original accessories/auxiliary equipment

■ Only use the accessories and additional

equipment that are speciﬁed in the operating

instructions and compatible with the appliance.

PTSS 1200 C2

■ 8 │ GB│IE

Before use

Fitting/changing the saw blade

Always remove the plug from the power socket

before working on the appliance.

NOTE

► Position the base plate for this operation on

the edge of a stable surface so that the saw

blade can be lowered.

1. Activate the safety lock-out and push the

motor unit forwards a little way.

2. Open the clamping lever .

Then push the motor unit forward until you

hear the lock click into place. Release the safety

lock-out . The movement of the motor unit is

blocked upward and downward.

3. The clamping screw/washer 14a is now located

in the cut-out 14b.

4. Press the spindle lock button (until it

engages) and use the hex key to release

the clamping screw/washer 14a .

5. Remove the saw blade .

NOTE

► Ensure that the factory-ﬁtted ﬂange X stays

in place during installation and removal

(see ﬁg. A).

Fig. A

6. To ﬁt a saw blade , carry out the above steps

in reverse order.

WARNING!

► The direction of rotation of the saw blade

and the machine must match.

Connecting the sawdust extractor

♦ If required, attach the chip ejector adapter for

dust extraction to the chip ejector .

♦ Connect an approved dust and chip extraction

device.

Checking blade guard functionality

NOTE

► Position the base plate for this operation on

the edge of a stable surface so that the saw

blade can be lowered.

♦ Activate the safety lock-out and lower the

circular saw.

♦ Check whether the saw blade rubs against

the blade guard and whether it moves back to

its starting position automatically.

Use

Switching on and oﬀ

Switching on

♦ Push the safety lock-out upwards and hold it

in position.

♦ Press the ON/OFF switch . Once the saw is

running, you can release the safety lock-out .

Switching oﬀ

♦ Release the ON/OFF switch .

X

PTSS 1200 C2 GB│IE │ 9 ■

Setting the cutting depth

♦ Undo the screw for the cutting depth

adjustment and push the stop to the desired

cutting depth on the cutting depth scale :

–without guide rail, see mark A.

–with guide rail, see mark B.

♦ Retighten the screw for the cutting depth

adjustment .

NOTE

► Adjust the cutting depth to the thickness of the

workpiece. The blade should not extend more

than one full tooth depth under the workpiece.

Setting the cutting angle

(mitreangle)

♦ Undo the two adjustment wheels for the cutting

angle .

♦ Tilt the motor to the desired cutting angle.

♦ Retighten the adjustment wheels .

NOTE

► If you have set the cutting angle adjustment to

0° or 45°, you can use the ﬁne adjustment

screws and 8a to make any ﬁne adjust-

ment that you require.

Note the cut line

♦ Cut line markings 9a of 0°/45° are imprinted

into the base plate .

♦ Align the appliance to the corresponding 0° or

45° cut line markings 9a in accordance with

the set cutting angle.

♦ The inclined surfaces are reference points for this.

Connecting the guide rails

The guide rails will help you to make straight

cuts.

♦ To connect the 2 guide rails, push the

connector into the groove of the guide rails.

Tighten the grub screws using the supplied

hex key.

NOTE

► The guide rails have a splinter guard

(black rubber lip). The splinter guard must be

adjusted before making the ﬁrst cut. Place the

guide rail onto a workpiece. Set a cutting

depth of approx. 10 mm. Switch the circular

saw on and push it gently and evenly in the

cutting direction.

9a

PTSS 1200 C2

■ 10 │ GB│IE

Eccentric screws

The eccentric screws are intended for the

adjustment of the ﬁt of the base plate on the

guide rail .

♦ Tighten the eccentric screws to reduce the

play between the circular saw and the guide

rails .

Sawing (without the guide rail)

Right-angled sawing

♦ Hold the machine with both hands ﬁrmly on

the handles and .

♦ Switch on the appliance as described in

"Switching on and oﬀ".

♦ Place the appliance with the front part of the

base plate on the workpiece.

♦ Swivel the motor down and saw forwards with

moderate pressure – never backwards.

Mitre angles up to 45°

♦ Adjust the cutting angle as described.

♦ Hold the machine with both hands ﬁrmly on

the handles and .

♦ Switch on the appliance as described in

"Switching on and oﬀ". Place the appliance with

the front part of the base plate on the work-

piece.

♦ Swivel the motor down and saw forwards with

moderate pressure – never backwards.

Plunge cuts

♦ When making a "plunge cut" that is not at right

angles, secure the base plate of the saw to

prevent any lateral movement. Lateral movement

can cause the saw blade to jam, thus causing a

kickback.

♦ Adjust the desired cutting depth as described

above.

♦ Place the appliance onto the workpiece.

♦ Avoid a kickback and place the rear edge

against a stop.

(reference is made to this in the section "Plunge

cutting using the guide rail").

♦ Switch on the appliance as described in

"Switching on and oﬀ".

♦ Hold the machine with both hands ﬁrmly on

the handles and and pivot it.

NOTE

► The cutting width marking on the side

ofthe blade guard shows the front and rear

cutting point of a 165 mm saw blade at

maximum cutting depth. This applies both

for plunge cuts using the guide rail and

plunge cuts without using the guide rail .

Sawing (with the guide rail)

Right-angled sawing with the guide rail

♦ Apply the guide rail with the foam rubber

elements onto the workpiece.

♦ Place the appliance with the groove onto

the guide rail .

♦ Switch on the appliance as described in

"Switching on and oﬀ".

♦ Hold the machine with both hands ﬁrmly on

the handles and and pivot it.

PTSS 1200 C2 GB│IE │ 11 ■

Mitre angles up to 45°

♦ Apply the guide rail with the foam rubber

elements onto the workpiece.

♦ Place the appliance with the groove onto

the guide rail .

♦ Adjust the cutting angle as described.

♦ Hold the machine with both hands ﬁrmly on

the handles and .

♦ Switch on the appliance as described in

"Switching on and oﬀ". Place the appliance

with the front part of the base plate on the

workpiece.

♦ Swivel the motor down and saw forwards with

moderate pressure – never backwards.

Plunge cutting using the guide rail

♦ Apply the guide rail with the foam rubber

elements onto the workpiece.

♦ Place the appliance with the groove onto

the guide rail .

♦ Adjust the desired cutting depth as described

above.

♦ Place the rear edge (as far as possible) against

a stop.

♦ Switch on the appliance as described in

"Switching on and oﬀ".

♦ Hold the machine with both hands ﬁrmly on

the handles and and pivot it.

NOTE

► The cutting width marking on the side

ofthe blade guard shows the front and rear

cutting point of a 165 mm saw blade at

maximum cutting depth. This applies both

for plunge cuts using the guide rail and

plunge cuts without using the guide rail .

Further applications are not permitted.

Cleaning and maintenance

WARNING! RISK OF INJURY! Switch

the appliance oﬀ and remove the

power plug before starting any work

on the appliance.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Use a soft, dry cloth to clean the housing.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Disposal

The packaging is made from environ-

mentally friendly material and can be

disposed of at your local recycling

plant.

Do not dispose of power tools

in your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools are

collected separately and recycled in an environ-

mentally compatible manner.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The pack-

aging material is labelled with abbreviations (a)

and numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

The product is recyclable, subject to

extended producer responsibility and

is collected separately.

PTSS 1200 C2

■ 12 │ GB│IE

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating

instructions for the product regarding proper use

of the product are to be strictly followed. Uses

and actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

over time

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

PTSS 1200 C2 GB│IE │ 13 ■

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g. IAN 12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free

of charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and information

about what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to the Lidl

service page (www.lidl-service.com) where you

can open your operating instructions by entering

the item number (IAN) 361911_2007.

WARNING!

►Have your appliances repaired by the

Service Centre or a qualiﬁed electrician

and only using genuine replacement parts.

This will ensure that the safety of the appli-

ance is maintained.

►Always ensure that the power plug or

the mains cable is replaced only by the

manufacturer of the appliance or by an

approved customer service provider. This

will ensure that the safety of the appliance is

maintained.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (oﬀ peak))

E-Mail: [email protected]

IAN 361911_2007

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PTSS 1200 C2

■ 14 │ GB│IE

Original declaration of conformity

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

Electromagnetic Compatibility

(2014 / 30 / EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer is solely responsible for issuance of the declaration of conformity. The object of the declaration

described above is in conformity with Directive 2011/65/EU of the European Parliament and of the Council of

8June 2011 on the restriction of use of certain hazardous substances in electrical and electronic equipment.

Applied harmonised standards

EN 62841-1:2015

EN 62841-2-5:2014

EN 55014-1:2006+A1+A2

EN 55014-1:2017

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type/appliance designation: Plunge saw PTSS 1200 C2

Year of manufacture: 11–2020

Serial number: IAN 361911_2007

Bochum, 13/11/2020

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

PTSS 1200 C2 DE│AT│CH │ 15 ■

Inhaltsverzeichnis

Einleitung .............................................................16

Bestimmungsgemäßer Gebrauch .......................................................16

Ausstattung ........................................................................16

Lieferumfang .......................................................................16

Technische Daten ...................................................................17

Allgemeine Sicherheitshinweise für Elektrowerkzeuge .......................18

1. Arbeitsplatzsicherheit ..............................................................18

2. Elektrische Sicherheit ..............................................................18

3. Sicherheit von Personen ............................................................18

4. Verwendung und Behandlung desElektrowerkzeugs .....................................19

5. Service .........................................................................20

Gerätespeziﬁsche Sicherheits hinweise für Handkreissägen ...................................20

Sicherheitshinweise fürKreissägeblätter ..................................................22

Vor der Inbetriebnahme ................................................22

Sägeblatt montieren/wechseln .........................................................22

Spanabsaugung anschließen ..........................................................23

Funktion der Schutzhaube prüfen .......................................................23

Inbetriebnahme .......................................................23

Ein-/ausschalten ....................................................................23

Schnitt-Tiefe einstellen (Tauchtiefe) ......................................................23

Schnitt-Winkel einstellen (Gehrungswinkel) ...............................................23

Schnittlinie beachten .................................................................23

Führungsschiene verbinden ...........................................................23

Exzenterschrauben ..................................................................24

Sägen (ohne Führungsschiene) ........................................................24

Sägen (mit Führungsschiene) ..........................................................24

Tauchsägen mit Führungsschiene .......................................................25

Reinigung und Wartung .................................................25

Entsorgung ...........................................................25

Garantie der Kompernaß Handels GmbH ..................................26

Service ...............................................................27

Importeur ............................................................27

Original-Konformitätserklärung ..........................................28

PTSS 1200 C2

■ 16 │ DE│AT│CH

TAUCHSÄGE PTSS 1200 C2

Einleitung

Wir beglückwünschen Sie zum Kauf Ihres neuen

Gerätes. Sie haben sich damit für ein hochwertiges

Produkt entschieden. Die Bedienungsanleitung ist

Teil dieses Produkts. Sie enthält wichtige Hinweise

für Sicherheit, Gebrauch und Entsorgung. Machen

Sie sich vor der Benutzung des Produkts mit allen

Bedien- und Sicherheitshinweisen vertraut. Benutzen

Sie das Produkt nur wie beschrieben und für die

angegebenen Einsatzbereiche. Händigen Sie alle

Unterlagen bei Weitergabe des Produkts an Dritte

mit aus.

Bestimmungsgemäßer Gebrauch

Die Tauchsäge (nachfolgend „Gerät“ oder

„Maschine“ genannt) ist zum Sägen von Längs-

und Querschnitten und Tauchschnitten bei fester

Auﬂage in Vollholz, Spanplatten, Kunststoﬀ und

Leichtbaustoﬀen geeignet. Das Bearbeiten von

Eisenmetallen ist nicht zulässig. Das Gerät kann

wahlweise mit den mitgelieferten Führungsschienen

– ausschließlich für die dazu beschriebenen Schnitt-

techniken – benutzt werden. Jede andere Verwen-

dung oder Veränderung der Maschine gilt als nicht

bestimmungsgemäß und birgt erhebliche Unfallge-

fahren. Nicht zum gewerblichen Gebrauch.

Ausstattung

Einschaltsperre

EIN-/AUS-Schalter

Handgriﬀ

Innensechskantschlüssel (klein)

Innensechskantschlüssel (groß)

Motoreinheit

Spanauswurfadapter

Feinjustierschrauben für 0°-Schnittwinkel

8a Feinjustierschraube für 45°-Schnittwinkel

Sägetisch

9a Schnittlinien-Markierung

Exzenterschraube (2 x)

Einstellrad für Schnittwinkeleinstellung (2 x)

Schnitttiefenverstellung

Schnitttiefenskala

Sägeblatt

14a Spannschraube/Unterlegscheibe

14b Montageausschnitt

Zusatzhandgriﬀ

Schnittbreitemarkierung

Spanauswurf (drehbar)

Festellhebel für Sägeblattwechsel

Spindelarretierung

Nut für Führungsschiene

Führungsschiene

Madenschrauben

Verbindungselement

X Flansch (Werkseitig montiert)

Lieferumfang

1 Tauchsäge

1 Sägeblatt 165 mm/24 Zähne (montiert)

2 Führungsschienen

1 Verbindungselement

1 Spanauswurfadapter

2 Innensechskantschlüssel

1 Bedienungsanleitung

PTSS 1200 C2 DE│AT│CH │ 17 ■

Technische Daten

Bemessungsspannung 230 V ∼, 50 Hz

(Wechselstrom)

Bemessungsaufnahme 1200 W

Bemessungs-

leerlaufdrehzahl n0 5200 min-1

Sägeblattaufnahme Ø 20 mm

165mm Sägeblatt-

durchmesser Ø 165 mm

Stammblattdicke 1,5 mm

Zahnstärke 2,6 mm

max. 65 mm

max.

Schnitttiefe 56 mm bei 90°

Gehrungswinkel

42 mm bei 45°

Gehrungswinkel

Mit Führungssschiene

minus 5 mm

Schutzklasse II / (Doppelisolierung)

Zubehör Führungsschiene 2 x

700 mm x 180 mm

Geräuschemissionswert

Messwert für Geräusch ermittelt entsprechend

EN62841. Der A-bewertete Geräuschpegel des

Elektrowerkzeugs beträgt typischerweise:

Schalldruckpegel LPA = 89 dB (A)

Unsicherheit KPA = 3 dB

Schallleistungspegel LWA = 100 dB (A)

Unsicherheit KWA = 3 dB

Gehörschutz tragen!

Schwingungsgesamtwert

Schwingungsgesamtwerte (Vektorsumme dreier

Richtungen) ermittelt entsprechend EN 62841:

Sägen von Holz ah,W = 1,3 m/s2

Unsicherheit K = 1,5 m/s2

HINWEIS

► Die in diesen Anweisungen angegebenen

Schwingungsemissionswert und Geräusch-

emissionswerte sind entsprechend einem

genormten Prüfverfahren gemessen worden

und können für den Gerätevergleich verwendet

werden. Der angegebene Schwingungs-

emissionswert und die Geräuschemissions-

werte können auch zu einer einleitenden Ein-

schätzung der Belastung verwendet werden.

WARNUNG!

► Die Schwingungs- und Geräuschemissionen

können entsprechend der Art und Weise in

der das Elektrowerkzeug verwendet wird,

insbesondere, welche Art von Werkstück

bearbeitet wird, abweichen und können in

manchen Fällen über dem in diesen Anwei-

sungen angegebenen Werten liegen. Die

Schwingungsbelastung könnte unterschätzt

werden, wenn das Elektrowerkzeug regel-

mäßig in solcher Weise verwendet wird. Ver-

suchen Sie, die Belastung durch Vibrationen

so gering wie möglich zu halten. Beispiel-

hafte Maßnahmen zur Verringerung der

Vibrationsbelastung sind das Tragen von

Handschuhen beim Gebrauch des Werk-

zeugs und die Begrenzung der Arbeitszeit.

Dabei sind alle Anteile des Betriebszyklus

zu berücksichtigen (beispielsweise Zeiten, in

denen das Elektrowerkzeug ab geschaltet ist,

und solche, in denen es zwar eingeschaltet

ist, aber ohne Belastung läuft).

Strona jest ładowana ...

Parkside PTSS 1200 C2 Instrukcja obsługi

Parkside PTSS 1200 C2 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty