Sony STR-DE345 Instrukcja obsługi

4-227-986-62(1)

FM Stereo

FM-AM Receiver

STR-DE345

STR-DE245

GB

RU

PL

Operating instructions

Инструкция по эксплуатации

Instrukcja obsługi

Getting Started

2

GB

WARNING

To prevent fire or shock

hazard, do not expose

the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to qualified

personnel only.

Do not install the appliance in a

confined space, such as a bookcase or

build-in cabinet.

Precautions

On safety

• Should any solid object or liquid fall

into the cabinet, unplug the receiver

and have it checked by qualified

personnel before operating it any

further.

On power sources

• Before operating the receiver, check

that the operating voltage is identical

with your local power supply. The

operating voltage is indicated on the

nameplate at the rear of the receiver.

• The unit is not disconnected from the

AC power source (mains) as long as it

is connected to the wall outlet, even if

the unit itself has been turned off.

• If you are not going to use the

receiver for a long time, be sure to

disconnect the receiver from the wall

outlet. To disconnect the mains lead,

grasp the plug itself; never pull the

cord.

• AC power cord must be changed only

at the qualified service shop.

• The mains switch is located on the

front exterior.

On placement

• Place the receiver in a location with

adequate ventilation to prevent heat

build-up and prolong the life of the

receiver.

• Do not place the receiver near heat

sources, or in a place subject to direct

sunlight, excessive dust or

mechanical shock.

• Do not place anything on top of the

cabinet that might block the

ventilation holes and cause

malfunctions.

On operation

• Before connecting other components,

be sure to turn off and unplug the

receiver.

On cleaning

• Clean the cabinet, panel and controls

with a soft cloth slightly moistened

with a mild detergent solution. Do

not use any type of abrasive pad,

scouring powder or solvent such as

alcohol or benzine.

If you have any question or problem

concerning your receiver, please

consult your nearest Sony dealer.

3

GB

Getting Started

TABLE OF CONTENTS

Getting Started

Unpacking 4

Hookup Overview 4

Aerial Hookups 5

Audio Component Hookups 5

Video Component Hookups 6

Speaker System Hookups 8

AC Hookups 9

Before You Use Your Receiver 10

Storing FM Stations Automatically in Alphabetical Order

(“Auto-betical”) 10

Receiver Operations

Selecting a Component 11

Receiving Broadcasts 13

Presetting Radio Stations 14

Using the Radio Data System (RDS) 15

Recording 17

Using the Sleep Timer 17

Using Surround Sound

Choosing a Sound Field 18

Getting the Most Out of Dolby Pro Logic Surround Sound 19

Additional Information

Troubleshooting 22

Specifications 23

Glossary 24

Index 25

Rear Panel Descriptions 26

Remote Button Descriptions 27

Quick Reference Guide 28

About This Manual

The instructions in this manual are for

models STR-DE345 and STR-DE245.

Check your model number by looking

at the upper right corner of the front

panel or lower right corner of the

remote. In this manual, the STR-DE345

and the remote RM-U304 are used for

illustration purposes. Any difference in

operation is clearly indicated in the text,

for example, “STR-DE345 only”.

Type of differences

Conventions

• The instructions in this manual

describe the controls on the receiver.

You can also use the controls on the

remote if they have the same or

similar names as those on the

receiver. For details on the use of the

remote RM-PP404 (STR-DE345 only),

refer to the separate operating

instructions supplied with the

remote.

• A “Quick Reference Guide” is

supplied on page 28.

• The “Remote Button Descriptions”

section on page 27 provides an

overview of the remote buttons for

RM-U304.

• The following icons are used in this

manual:

Indicates that you can use only the

remote to do the task.

Indicates hints and tips for making

the task easier.

This receiver contains a Dolby Pro Logic

Surround decoder.

Manufactured under license from Dolby

Laboratories.

“Dolby”, “AC-3”, “Pro Logic” and the

double-D symbol ; are trademarks of

Dolby Laboratories.

GB

FR

NL

SE

DK

5.1 CH (VIDEO IN)

VIDEO

MONITOR

Feature

DE345

•

Model

DE245

Getting Started

4

GB

Unpacking

Check that you received the following items with the

receiver:

• FM wire aerial (1)

• AM loop aerial (1)

• Remote commander (remote) (1)

Model Remote

STR-DE345 RM-PP404

STR-DE245 RM-U304

• Size AA (R6) batteries (2)

• Operating instructions of the remote RM-PP404

(STR-DE345 only)

Inserting batteries into the remote

Insert two size AA (R6) batteries in accordance with

the + and – markings on the battery compartment.

When using the remote, point it at the remote sensor g

on the receiver.

]

}

When to replace batteries

Under normal use, the batteries should last for about 6

months. When the remote no longer operates the

receiver, replace both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or humid

place.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from

battery leakage and corrosion.

Hookup Overview

The receiver allows you to connect and control the

following audio/video components. Follow the

hookup procedures for the components that you want

to connect to the receiver on the pages specified. To

learn the locations and names of each jack, see “Rear

Panel Descriptions” on page 26.

Before you get started

• Turn off the power to all components before making

any connections.

• Do not connect the mains lead until all of the

connections are completed.

• Be sure to make connections firmly to avoid hum

and noise.

• When connecting an audio/video cable, be sure to

match the color-coded pins to the appropriate jacks

on the components: Yellow (video) to Yellow; White

(left, audio) to White; and Red (right, audio) to Red.

Front

speaker

(L)

Front

speaker

(R)

Rear

speaker

(L)

Speaker

System

Hookups (8)

AM/FM aerial

Aerial Hookups (5)

Centre

speaker

DVD player/AC-3

decoder

Active

woofer

Rear

speaker

(R)

TV monitor

(STR-DE345

only)

TV tuner

SAT (Satellite

receiver)

VCR

Video Component

Hookups (6)

CD player

MD/TAPE deck

Audio Component

Hookups (5)

5

GB

Getting Started

Aerial Hookups

Overview

This section describes how to connect AM and FM

aerials to the receiver. If you want to receive radio

broadcasts with the receiver, complete these

connections first, then go to the following pages.

For specific locations of the terminals, see the

illustration below.

ANTENNA

What aerials will I need?

Hookups

ANTENNA

AM

FM

75

Ω

COAXIAL

If you have poor FM reception

Use a 75-ohm coaxial cable (not supplied) to connect the

receiver to an outdoor FM aerial as shown below.

ANTENNA

AM

FM

75

Ω

COAXIAL

If you have poor AM reception

Connect a 6 to 15-meter (20 to 50 ft.) insulated wire (not

supplied) to the AM aerial terminal in addition to the

AM loop aerial. Try to extend the wire outdoors and

keep it horizontal.

Connecting a ground wire

If you connect the receiver to an outdoor aerial, ground

it against lightning as shown in the illustration in the

left column. To prevent a gas explosion, do not connect

the ground wire to a gas pipe.

Where do I go next?

If you want to connect other components, go on to the next

section. If you’re only planning to use the receiver to listen to

the radio, go to “Speaker System Hookups” on page 8.

Audio Component Hookups

Overview

This section describes how to connect your audio

components to the receiver. If you want to use the

receiver as an amplifier, complete these connections.

For specific locations of the jacks, see the illustration

below.

MD/TAPE

CD

What cords will I need?

Audio cords (not supplied) (1 for CD player; 2 for each MD

deck or tape deck)

• FM wire aerial

(supplied) (1)

• AM loop aerial

(supplied) (1)

AM loop aerial

Receiver

After connecting

the wire aerial,

keep it as

horizontal as

possible.

Receiver

Red (R)Red (R)

White (L)White (L)

(continued)

FM outdoor aerial

Ground wire

(not supplied)

FM wire aerial

to ground

Getting Started

6

GB

Hookups

The arrow l indicates signal flow.

CD player

CD

IN

L

R

OUTPUT

LINE

L

R

MD deck or Tape deck

IN

OUTPUT

LINE

INPUT

LINE

L

R

MD/TAPE

REC OUT

L

R

Where do I go next?

Go on to the next section to connect video components to

enjoy surround sound when watching/listening to TV

programmes or video tapes.

Video Component Hookups

Overview

This section describes how to connect video

components to the receiver. For specific locations of the

jacks, see the illustration below.

TV/SAT

5.1 CH (VIDEO IN)

(STR-DE345 only)

5.1 CH/DVD VIDEO

Receiver

CD player

MD deck or Tape deck

Receiver

What cords will I need?

• Audio/video cords (not supplied) (1 for each TV tuner or

Satellite receiver; 2 for the VCR)

STR-DE345 only

STR-DE245 only

• Video cord (not supplied) (1 for a TV monitor) (STR-

DE345 only)

Hookups

The arrow l indicates signal flow.

You can listen to the sound from VCR or TV/SAT by

connecting the audio signal from VCR or TV/SAT to

the receiver.

TV/SAT

AUDIO IN

L

R

TV/SAT

VIDEO IN

AUDIO

OUTPUT

VIDEO

L

R

*STR-DE345 only

MONITOR (STR-DE345 only)

MONITOR

VIDEO OUT

INPUT

VIDEO

MONITOR (STR-DE345 only)

Yellow

White (L)

Red (R)

Yellow

White (L)

Red (R)

Yellow

TV monitorReceiver

Red (R)

White (L)

Receiver

TV tuner or Satellite

receiver

(STR-DE345 only)

7

GB

Getting Started

VCR

AUDIO IN

VIDEO

VIDEO IN

AUDIO

OUTPUT

VIDEO

AUDIO

INPUT

VIDEO

AUDIO OUT

L

R

VIDEO OUT

L

R

*STR-DE345 only

Use the function buttons (TV/SAT, CD, MD/TAPE etc.)

to select the VIDEO AUDIO OUT signal. You can record

this audio signal by connecting a recording component

such as a cassette deck (to the VIDEO AUDIO OUT

jack).

DVD player/AC-3 decoder

What cords will I need?

• Audio cords (not supplied) (1 for each 5.1 CH/DVD

FRONT and REAR jacks)

• Monaural audio cord (not supplied) (1 for each 5.1

CH/DVD CENTER and SUB WOOFER jacks)

• Video cord (not supplied) (1 for the 5.1 CH VIDEO

IN jack) (STR-DE345 only)

White (L)

Red (R)

White (L)

Red (R)

Black

Yellow

Receiver

Dolby Digital AC-3

decoder, etc.

Receiver

VCR

Receiver

Dolby Digital AC-3

decoder, etc.

You can play decoded Dolby Digital AC-3 soundtracks

through the speakers connected to the receiver.

If you have a Dolby Digital AC-3 decoder you can

amplify a decoded Dolby Digital AC-3 soundtrack with

the following connections.

FRONTREARCENTER

WOOFER

PRE OUT

5.1 CH/DVD

FRONT REAR CENTER

SUB

WOOFER

L

R

VIDEO

VIDEO IN

5.1 CH

*STR-DE345 only

Where do I go next?

Go on to the next section to connect the speakers.

Getting Started

8

GB

Hookups

Front Speakers

SPEAKERS

FRONT

R

L

Rear and centre speakers

SPEAKERS

REAR

L

R

CENTER

To avoid short-circuiting the speakers

Short-circuiting of the speakers may damage the

receiver. To prevent this, make sure to take the

following precautions when connecting the speakers.

Make sure the stripped ends of each speaker cord does

not touch another speaker terminal or the stripped end

of another speaker cord.

Examples of poor conditions of the speaker cord:

F

R

O

N

T

S

P

E

A

K

E

R

S

–

R

L

+

Stripped speaker cord is touching another speaker

terminal.

–

FRONT

SPEAKERS

R

L

+

Stripped cords are touching each other due to excessive

removal of insulation

Front speaker

(R)

Front speaker

(L)

Receiver

Rear speaker

(R)

Rear speaker

(L)Centre speaker

Speaker System Hookups

Overview

This section describes how to connect your speakers to

the receiver. Although front (left and right) speakers

are required, centre and rear speakers are optional.

Adding centre and rear speakers will enhance the

surround effects. Connecting an active woofer will

increase bass response. For specific locations of the

terminals, see the illustration below.

SPEAKERS REAR SPEAKERS FRONT

SUB WOOFER

SPEAKERS CENTER

For optimum surround sound effect, place your

speakers as shown below.

45°

What cords will I need?

Speaker cord (not supplied) (1 for each speaker)

Twist the stripped ends of the cord about 15 mm (2/3 inch).

Be sure to match the speaker cord to the appropriate

terminal on the components: + to + and – to –. If the cords

are reversed, the sound will be distorted and will lack bass.

60 - 90 cm

Rear speaker

(+)(+)

(–)

9

GB

Getting Started

After connecting all the components, speakers and AC

power cord, output a test tone to check that all the

speakers are connected correctly. For details on

outputting a test tone, refer to ”Adjusting the speaker

volume”, on page 20.

If you have connected rear speakers, be sure to press

the 5.1 CH/DVD button and turn off sound field on

the receiver before outputting a test tone so that the

tone is output individually from the left and right rear

speakers.

If no sound is heard from a speaker while outputting a

test tone or a test tone is output from a speaker other

than the one whose name is currently displayed on the

receiver, the speaker may be short-circuited. If this

happens, check the speaker connection again.

Active woofer

SUB

WOOFER

AUDIO OUT

INPUT

Note

Do not connect any other component.

To listen to the speakers

Make sure that you set the SPEAKERS button to ON.

If your TV monitor uses separate speakers

You can connect one of them to the SPEAKERS

CENTER terminals for use with Dolby Pro Logic

Surround sound (see page 19).

Where do I go next?

To complete your system, go to “AC Hookups” on this page.

Receiver

Active Woofer

to a wall outlet

AC Hookups

Connecting the mains lead

Connect the mains lead from this receiver and from

your audio/video components to a wall outlet.

Where do I go next?

Before you use the receiver, go to the next section to make

sure that all the controls are set to the appropriate positions.

,

Getting Started

10

GB

Storing FM Stations

Automatically in Alphabetical

Order (“Auto-betical”)

With “Auto-betical select” you can automatically store

up to 30 FM and FM RDS stations in alphabetical order

without redundancy. Additionally, “Auto-betical

select” only stores the stations with the clearest signals.

If you want to store FM or AM (MW) stations one by

one, see “Presetting Radio Stations” on page 14.

FM RDS stations are stored first, in alphabetical order

by their Station Name, followed by regular FM stations

in order of frequency. (For more details on RDS, see

page 15.)

1 Press ?/1 (power) to turn off the receiver.

2 Hold down MEMORY and press ?/1 (power) to

turn the receiver on.

”AUTOBETICAL SELECT” appears and the

receiver scans and stores all the FM and FM RDS

stations in the broadcast area.

“FINISH” appears when the receiver has finished

storing the FM and FM RDS stations.

To change a preset code to another station

See ”Presetting Radio Stations” on page 14.

To stop Auto-betical before storing all the stations

Press ?/1 (power) to turn the receiver off.

Stations currently stored in the preset memory are

shifted to the rear (toward C0) and may be erased,

depending on the number of stations received by Auto-

betical select.

Notes

• If you move to another area, repeat this procedure to store

stations in your new area.

• For details on tuning to the preset stations, see page 14.

• Once “FINISH” appears, all the previous preset memories

are cleared. Preset AM stations again if necessary.

Before You Use Your Receiver

Before turning on the receiver, make sure that you have:

• Set the SPEAKERS button to ON.

Before you use your receiver for the first time or when

you want to clear the receiver's memory, do the

procedure below:

MUTING

DIMMER

1 Turn off the receiver.

2 Press ?/1 (power) for more than 4 seconds.

“INITIAL” appears in the display and the items

including the following are reset or cleared:

• All preset stations are reset to their factory

settings.

• All sound field parameters are reset to their

factory settings.

• All index names (of preset stations and

programme sources) are cleared.

• All adjustments made with the SET UP button are

reset to their factory settings.

• The sound field memorized for each programme

source and preset station is cleared.

Turn on the receiver and check the following indicator.

• Press MUTING if the MUTING indicator turns on.

• Press DIMMER repeatedly to set the display at any

of four levels of brightness.

?/1 (power)

11

GB

Receiver Operations

Selecting a Component

To listen to or watch a connected component, first

select the function on the receiver or with the remote.

Before you begin, make sure you have:

• Connected all components securely and correctly as

indicated on pages 5 to 9.

MENU </>

MASTER

VOLUME

LEVEL

BASS

BOOST

TREBLE

BASS +/– MUTING

1 Press ?/1 (power) to turn on the receiver.

2 Press a function button to select the component

you want to use:

3 Turn on the component, for example, a CD player,

and then start playing.

To tune in radio stations on this receiver, see

“Receiving Broadcasts” on page 13.

4 Turn MASTER VOLUME to adjust the volume.

Every time you turn MASTER VOLUME, the

display changes as follows:

VOL MIN y VOL 1 y … y VOL 30 y

VOL MAX

To adjust the volume of the TV's speaker

Use the volume control on the TV.

To avoid damaging your speakers

Make sure that you turn down the volume before you

turn off the receiver. When you turn on the receiver, the

volume remains at the level you turn off the receiver.

To

Mute the sound

Reinforce the bass

Adjust the balance

Adjust the tone quality

When you listen with headphones

Connect the headphones to the PHONES jack and set

the SPEAKERS button to OFF.

Watching/listening to video programmes

When you watch/listen to TV or video programmes,

we recommend you play audio portion through the

receiver instead of your TV’s speaker. This lets you

take advantage of the receiver’s surround sound

effects, such as Dolby Pro Logic Surround and lets you

use the receiver’s remote to control the audio. Turn off

the speakers on your TV before you start so you can

enjoy the surround sound from your receiver.

To watch/listen to TV programmes, turn on the TV, TV

tuner and the receiver and press TV/SAT on the receiver.

To watch videos, do the following:

1 Press VIDEO to select the VCR.

2 Turn on the TV and set the TV’s video input to

match your video component.

3 Turn on the VCR, and start playback.

Using the remote (STR-DE245 only)

The remote lets you operate the receiver and the Sony

components that are connected to it.

To listen to or watch

Radio programmes

Compact discs (CD)

MiniDisc (MD) or Audio

tapes

TV programmes or

Satellite receiver

Video tapes

DVD player/AC-3 decoder

Press

TUNER

CD

MD/TAPE

TV/SAT

VIDEO

5.1 CH/DVD

Do this

Press MUTING. Press again to

restore the sound.

Press BASS BOOST to turn on

the BASS BOOST indicator.

1 Press LEVEL or CURSOR

MODE on the remote

repeatedly until the LEVEL

indicator lights up.

2 Press MENU < or >

repeatedly until

“BALANCE” appears on the

display.

3 Press + or – to adjust the

balance right or left.

Press BASS +/– and TREBLE

+/– to adjust the tone level.

You can select a tone level of -6

dB to +6 dB in 2-dB steps.

Receiver Operations

(continued)

Function buttons

BASS BOOST indicator

?/1 (power)

?/1

Function

buttons

Receiver Operations

12

GB

1 Press one of the Function buttons to select the

component you want to use.

The Function buttons on the remote are factory-

set as follows:

If you want to change the factory setting of a

button, see the next section.

The receiver and the selected component turn on.

If the component does not turn on

Press the power switch on the component.

2 Start playing.

Refer to “Remote Button Descriptions” on page 27

for details.

Changing the factory setting of a

function button (STR-DE245 only)

If the factory settings of the FUNCTION buttons don’t

match your system components, you can change them.

For example, if you have two CD players and you

don’t have a tape deck or an MD deck, you can assign

the MD/TAPE button to your second CD player.

Note that the settings of the TUNER button cannot be

changed.

?/1

AV ?/1

MASTER VOL –

> 10

.

ENTER

To listen or to watch

Radio programmes

Compact discs (CD)

MiniDisc (MD) or

Audio tapes

TV programmes or

Satellite receiver

VHS Video tapes

(VTR-3 mode)

DVD player/

AC-3 decoder

Press

TUNER

CD

MD/TAPE

(INITIAL-MD MODE)

TV/SAT

(INITIAL-TV MODE)

VIDEO

DVD/LD

(INITIAL-DVD MODE)

1 Hold down the Function button whose function

you want to change (for example, MD/TAPE).

2 Press the corresponding button of the component

you want to assign to the Function button (for

example, 1 - CD player).

The following buttons are assigned to select the

functions:

* Sony VCRs are operated with a VTR 1, 2 or 3 setting.

These correspond to Beta, 8mm and VHS respectively.

Now you can use the MD/TAPE button to control

a second CD player.

To change the AUX function to another function

Hold down SLEEP and press the corresponding button of

the component you want to assign it to.

To change the 5.1 CH function to another function

Hold down AV ?/1 and press the corresponding button of

the component you want to assign it to.

To reset a button to its factory setting

Repeat the above procedure.

To reset all the function buttons to their factory setting

Press ?/1, AV ?/1 and MASTER VOL – at the same time.

To operate

CD player

DAT deck

MD deck

Tape deck A

Tape deck B

LD player

VCR (remote control mode VTR 1*)

VCR (remote control mode VTR 2*)

VCR (remote control mode VTR 3*)

TV

DSS (Digital Satellite System)

DVD

VCD player

Press

1

2

3

4

5

6

7

8

9

0

> 10

ENTER

.

Function

buttons

Numeric buttons

13

GB

Receiver Operations

Receiving Broadcasts

This receiver lets you enter a station’s frequency

directly by using the numeric buttons on the remote

(direct tuning). If you don’t know the frequency of the

station you want, see “Receiving broadcasts by

scanning stations (automatic tuning)”.

Before you begin, make sure you have:

• Connected an FM/AM aerial to the receiver as

indicated on page 5.

• Set the SPEAKERS button to ON.

MASTER VOLUME TUNING +/–

FM MODEFM/AMTUNER

D. TUNING

1 Press ?/1 (power) to turn on the receiver.

2 Press TUNER.

The last received station is tuned in.

3 Press FM/AM to select FM or AM stations.

4 Press D. TUNING on the remote.

5 Press the numeric buttons on the remote to enter

the frequency.

Example 1: FM 102.50 MHz Example 2: AM 1350 kHz

02501

3501

6 When you tune in AM stations, adjust the

direction of the AM loop aerial for optimum

reception.

To receive other stations

Repeat Steps 3 to 5.

If the STEREO indicator remains off

Press FM MODE when an FM stereo broadcast is

received.

If an FM stereo programme is distorted

The STEREO indicator flashes. Press FM MODE to

change to monaural (MONO). You will not have the

stereo effect but the distortion will be reduced. To

return to stereo mode, press this button again.

If you cannot tune in a station and the entered

numbers are flashing

Make sure you’ve entered the right frequency. If not,

press D. TUNING and re-enter the frequency you want

on the remote. If the entered numbers still flash, the

frequency is not used in your area.

To watch FM simulcast TV programmes

Make sure that you tune in the simulcast programme

both on the TV (or the VCR) and on the receiver.

If you enter a frequency not covered by the tuning

interval

The entered value is automatically rounded up or down

to the closest covered value.

Tuning intervals for direct tuning are:

FM: 50 kHz intervals

AM: 9 kHz intervals

Receiving broadcasts by scanning stations

(automatic tuning)

If you don’t know the frequency of the radio station

you want, you can have the receiver scan all the

receivable stations to locate the one you want.

1 Press TUNER.

The last received station is tuned in.

2 Press FM/AM to select FM or AM.

3 Press TUNING + or –.

Press the + button for a higher frequency; press

the – button for a lower one. When you tune past

either end of the band, the receiver automatically

jumps to the opposite end. Every time a station is

received, the receiver stops scanning. To continue

scanning, press the button again.

numeric buttons

?/1 (power)

Receiver Operations

14

GB

Presetting Radio Stations

You’ll most likely want to preset the receiver with the

radio stations you listen to often so that you don’t have

to tune in the station every time. The receiver can store

a total of 30 FM or AM stations. You can store the

stations on preset numbers combining three characters

(A, B, C) and numbers (0 - 9). For example, you can

store a station as preset number A1, B6 or C9, etc.

DISPLAY

MENU </> NAME

PRESET/PTY SELECT +/–

SHIFT

MEMORYENTER+/–TUNER

1 Press TUNER.

The last received station is tuned in.

2 Tune in the station you want.

If you are not familiar with how to tune in a

station, see “Receiving Broadcasts” on the

previous page.

3 Press MEMORY.

“MEMORY” appears for a few seconds.

Do steps 4 to 6 before “MEMORY” goes out.

4 Press SHIFT to select a character (A, B or C).

Each time you press SHIFT, the letter “A”, “B” or

“C” appears in the display.

If “MEMORY” disappears, start again from step 3.

5 Select a preset number by pressing PRESET/PTY

SELECT + or PRESET/PTY SELECT –.

6 Press MEMORY again to store the station.

7 Repeat Steps 2 to 6 to preset other stations.

To change a preset station

Preset a new station on the number you want to change.

Note

If the mains lead is disconnected for about one week, the

preset stations will be cleared from the receiver’s memory,

and you will have to preset the stations again.

n A1 ˜ A2 ˜ … ˜ A0 ˜ B1 ˜ B2 ˜ … ˜ B0 N

n C0 ˜ … ˜ C2 ˜ C1 N

Tuning preset stations (preset tuning)

You can tune directly to a preset station by entering its

preset number. If you don’t know which stations are

preset on which numbers, you can tune by scanning

the preset stations.

1 Press TUNER.

The last received station is tuned in.

2 Press SHIFT to select a character (A, B or C), then

press the number on the remote.

For example, to tune in the station preset as A7,

select A and then press 7.

You can tune by scanning the preset stations

First press TUNER and then press PRESET/PTY

SELECT + or – to select the station you want. Each time

you press the buttons, the preset numbers change as

follows:

Naming preset stations

You can store names (index name), up to 8 characters

long, for your preset stations (except for FM RDS

stations). Once you name a preset station, the name

appears in the display instead of the frequency when

you tune to that preset station. The characters you can

use include letters, numbers and symbols.

1 Tune to the preset station you want to name.

2 Press NAME.

The cursor blinks in the display.

3 Use + or – to select the character you desire.

4 Press MENU </> to move the cursor into position

for the next character.

5 Repeat steps 3 and 4 to enter up to 8 characters.

6 Press ENTER to store the names.

If you make a mistake

Press MENU </> repeatedly so that the character you want

to change blinks in the display, then use + or – to select the

desired character.

Notes

• You can also enter a name of up to 8 characters for

programme sources. Select the programme source you

want and repeat steps 2 to 6 (except 5.1 CH/DVD).

• To clear programme source name, press NAME and then

press the same programme source button. Press ENTER to

delete the name (except TUNER).

15

GB

Receiver Operations

Using the Radio Data System

(RDS)

What you can do with the Radio Data

System

Radio Data System (RDS) is a broadcasting service that

allows radio stations to send additional information

along with the regular radio programme signal. This

receiver offers you three convenient RDS features:

Displaying the RDS information; Monitoring of traffic,

news, or information programmes; and Locating a

station by programme type. RDS is available only on

FM stations.*

Note

RDS may not work properly if the station you are tuned to is

not transmitting the RDS signal properly or if the signal

strength is weak.

* Not all FM stations provide RDS service, nor do they

provide the same types of services. If you are not familiar

with the RDS system, check with your local radio stations

for details on RDS services in your area.

Receiving RDS broadcasts

Simply select a station from the FM band.

When you tune in a station that provides RDS services,

the station name appears in the display.

Displaying the RDS Information

Press DISPLAY. Each time you press DISPLAY, the

display advances one step through the following

information.

**This information also appears for non-RDS FM stations.

Information displayed

Station Name**

Frequency**

Programme Type

Radio Text

Clock (24-hour system)

You can:

Locate each station by name

(e.g., WDR) instead of

frequency.

Locate each station by

frequency.

Locate a specific type of

programme being broadcast.

(See page 16 for the types of

programmes you can select.)

Display the text messages sent

by the RDS station.

Display the current time

Notes

• If there is an emergency announcement by governmental

authorities, ALARM flashes in the display.

• When the message consists of 9 characters or more, the

message scrolls across the display.

• The following messages appear if a station is not

providing a particular RDS service:

“NO PTY” (the selected programme type is not available)

“NO TEXT” (text data is not available)

“NO TIME” (clock time data is not available)

• Depending on the method used by the radio station to

send the text, some text messages may be incomplete.

Monitoring traffic, news, or information

programmes (EON)

The EON (Enhanced Other Network) function allows

the receiver to switch automatically to a station

broadcasting traffic announcements, news or

information programmes. When such a programme

starts on a station networking with the preset FM RDS

station, the receiver automatically tunes in the station.

After the programme ends, the receiver switches back

to the original preset station or the programme source

you were originally listening to.

1 Tune to an FM station.

2 Press RDS EON to select the programme you

want to monitor.

Each time you press RDS EON, the indicators

light as follows:

TA (Traffic Announcement)

.

NEWS

.

INFO (Information)

.

OFF (No indication lights up)

The receiver enters EON standby mode.

“NO TA”, “NO NEWS”, or “NO INFO” appears if you

press RDS EON before tuning to an RDS station.

When a station starts broadcasting the programme you

selected, the receiver switches to the station, a message

(e.g., “NOW TA”) appears and the respective indicator

(e.g.,“TA”) flashes. After the programme ends, the

receiver switches back to the station you were listening

to (or the function you were using).

To stop monitoring the programme

Press RDS EON once.

/

(continued)

Receiver Operations

16

GB

Turn off the EON feature when you want to record a

programme without interruptions, especially when you

want to do timer recording.

Notes

• To use this function, be sure to store the RDS stations

beforehand.

• When the selected station has a weak signal, “WEAK SIG”

appears and then, the receiver returns to the previous

station or programme source.

Locating a station by programme type

(PTY)

You can locate a station you want by selecting a

programme type. The receiver tunes in the type of

programmes currently being broadcast from the RDS

stations stored in the receiver's preset memory.

1 Press RDS PTY to display the current PTY type.

Press PRESET/PTY SELECT + or – until the

programme type you want appears in the display.

See the following table for the programme types

you can select.

2 Press RDS PTY while the programme type

appears in the display.

The tuner starts searching the preset RDS stations

for the programme (“SEARCH” and the

programme type are displayed alternately).

When the receiver finds the programme you are

looking for, it stops searching. The preset number

of the preset station currently broadcasting the

selected programme type flashes, and the receiver

receives the station.

Note

“NO PTY” appears when the programme type that you've

selected is not being broadcast and the receiver returns to

the original station.

Programme

type

CULTURE

SCIENCE

VARIED

POP M

ROCK M

EASY M

LIGHT M

CLASSICS

OTHER M

WEATHER

FINANCE

CHILDREN

SOCIAL

RELIGION

PHONE IN

TRAVEL

LEISURE

JAZZ

COUNTRY

NATION M

OLDIES

FOLK M

DOCUMENT

Programme

type

NONE

NEWS

AFFAIRS

INFO

SPORT

EDUCATE

DRAMA

You can select the following programme types:

What you hear

Any programmes not defined below.

News programmes.

Topical programmes that expand on

current news.

Programmes about consumer affairs and

professional advice (eg. medical advice).

Sports programmes.

Educational programmes, such as a “how-

to” programme and advice.

Radio plays and serials.

What you hear

Programmes about national or regional

culture, such as religion, language, and

societal concerns.

Programmes about the natural sciences.

Programmes containing celebrity

interviews, panel games, and comedy.

Popular music programmes.

Rock music programmes.

Easy listening (middle of the road music).

Classical music, such as instrumental,

vocal, and choral.

Performances of major orchestras,

chamber music, opera, etc.

Music that does not fit into any of the

above categories, such as rhythm & blues

and reggae.

Programmes about the weather report.

Stock Market reports, commerce, trading

etc.

Programmes targeted at young audience

for entertainment and interest.

Programmes on sociology, history,

geography, psychology and society.

Aspect of beliefs and faiths.

Expression of views by phone or at a

public forum.

Programmes on package tours,

destinations, travel ideas and

opportunity.

Programmes on recreational activities

which listeners might participate.

Polyphonic, syncopated music.

Songs originating from American

Southern States.

Current popular music of the Nation or

Region.

“Golden age” music.

Music which has roots in the musical

culture of a particular nation.

Programme concerning factual matters.

17

GB

Receiver Operations

Recording

This receiver makes it easy to record to and from the

components connected to the receiver. You don’t have

to connect playback and recording components

directly: once you select a programme source on the

receiver, you can record and edit as you normally

would using the controls on each component.

Before you begin, make sure you’ve connected all

components properly.

l: Audio signal flow

.: Video signal flow (STR-DE345 only)

Recording on a MiniDisc or audio tape

You can record on a MiniDisc or cassette tape using the

receiver. See the instruction manual of your MD deck

or tape deck if you need help.

1 Press one of the function buttons to select the

programme source.

2 Set the component to be ready for playing.

For example, insert a CD into the CD player.

3 Insert a blank disc or tape into the recording deck

and adjust the recording level, if necessary.

4 Start recording on the recording deck and then

start playing the component.

Recording on a video tape

You can record from a TV or a Satellite receiver using

the receiver. You can also add audio from a variety of

audio sources when editing a video tape. See your

VCR’s instruction manual if you need help.

Recording component

(MD deck, Tape deck,

VCR)

Playback component

(programme source)

1 Press TV/SAT to select the programme source.

2 Set the component to be ready for playing.

For example, turn on the TV and TV tuner.

3 Insert a blank video tape into the VCR for

recording.

4 Start recording on the VCR.

You can replace audio while editing a video tape

At the point you want to start adding different sound,

press another function button (for example, CD) and

start playback. The sound from the selected component

will be recorded over the original audio.

To resume recording the original sound, press the TV/

SAT function button.

Note

You cannot record the audio and video signal during

5.1 CH/DVD mode.

Using the Sleep Timer

n 2:00:00 n 1:30:00 n 1:00:00 n 0:30:00 n OFF

You can set the receiver to turn off automatically at a

time you specify.

SLEEP

Press SLEEP on the remote while the power is on.

Each time you press SLEEP, the time changes as shown

below.

The display dims after you specify the time.

You can check the time remaining before the

receiver turns off

Press SLEEP on the remote. The remaining time appears

in the display.

Function buttons

Using Surround Sound

18

GB

You can take advantage of surround sound simply by

selecting one of the pre-programmed sound field

according to the type of music you wish to play.

SOUND FIELD

MODE +/–

+/– SUR

SOUND FIELD

ON/OFF

SOUND FIELD

MODE

CURSOR

MODE

+/–

1 Press SOUND FIELD ON/OFF to turn on the

sound field.

The sound field indicator lights up.

2 Press SOUND FIELD MODE +/– repeatedly until

the sound field you want appears on the display.

Select the appropriate sound field as follows:

Choosing a Sound Field

Type

CINEMA

VIRTUAL

(STR-DE345

only)

MODE (Sound field)

PRO LOGIC*

C. STUDIO

(Cinema Studio)

DOLBY V

V SURR**

Effects

Decodes programmes

processed with Dolby

Pro Logic Surround.

Reproduces the sound

characteristics of a

movie theater. Good for

watching standard

movies.

Uses front speakers to

create surround sound

effects.

Uses front speakers and

centre speaker to create

surround sound effects.

When you use the remote

Each time you press SOUND FIELD MODE, sound field

changes as follows:

When selecting programme source

*** When using 5.1 CH/DVD

C. STUDIO y V SURR

* “DOLBY PL” appears on the display.

*** STR-DE345 only.

To turn off sound field

Press SOUND FIELD ON/OFF.

The receiver memorizes the last sound field selected

for each programme source (Sound Field Link) (STR-

DE345 only)

Whenever you select a programme source, the sound

field that was last applied is automatically applied

again. For example, if you listen to CD with HALL as

the sound field, change to different programme source,

then return to CD, HALL will be applied again. In the

case of the tuner, the sound fields for AM or FM band

and for all the preset stations are memorized separately.

You can find Dolby Surround-encoded software by

looking at the packaging

However, some videos and laser discs may use Dolby

Surround sound even if it’s not indicated on the

package.

Sound field

indicator

t PRO LOGIC* t C. STUDIO

HALL T DOLBY V *** T

Type

MUSIC

* “DOLBY PL” appears on the display.

** When using 5.1 CH/DVD only.

MODE (Sound field)

HALL

Effects

Reproduces the

acoustics of a

rectangular concert hall.

Ideal for soft acoustic

sounds.

19

GB

Using Surround Sound

Getting the Most Out of Dolby

Pro Logic Surround Sound

To obtain the best possible Dolby Pro Logic Surround

sound, first select the centre mode according to the

speaker system you have. Then, adjust each speaker

volume and delay time.

Note that you must have at least one additional pair of

speakers and/or one centre speaker to do the following

adjustments.

SOUND FIELD

MODE +/–

SOUND FIELD

ON/OFF

SET UP

+/–LEVEL

MENU </>

SOUND FIELD

MODE

TEST TONE

CURSOR

MODE

+/–

MENU </>

Selecting the centre mode

The receiver offers you four centre modes: Phantom,

Normal, Wide and 3 STEREO. Each mode is designed

for a different speaker configuration. Select the mode

that best suits your speaker’s system configuration:

1 Press SOUND FIELD ON/OFF to turn on the

sound field.

2 Press SOUND FIELD MODE +/– repeatedly to

select the Dolby surround sound field (PRO

LOGIC or C.STUDIO mode).

3 Press SET UP.

4 Press MENU < or > repeatedly until “CTR

MODE” appears on the display.

Adjusting the Effect Level (all sound fields

except PRO LOGIC)

You can make the surround sound more prominent by

increasing the EFFECT level. This control lets you

adjust the “presence” of the surround effect in six steps

(1-6).

1 Start playing a programme source.

2 Press SUR.

The effect level (“EFFECT 1” … “EFFECT 6”)

appears on the display.

3 Press +/– to select the level you prefer.

When you use the remote

Press CURSOR MODE on the remote repeatedly until

the SUR indicator lights up. Each time you press +/–,

the effect level changes as follows:

EFFECT 1 y EFFECT 2 y … y EFFECT 6

Note

Changing the effect level may not produce major variations

in the surround effect when used with certain playback

sources.

(continued)

Using Surround Sound

20

GB

You can adjust all speakers at one time

Adjust MASTER VOL on the remote or MASTER

VOLUME on the receiver.

You can also adjust the volume level with the

controls on the receiver

After pressing TEST TONE on the remote:

• Press MENU < or > repeatedly to select “CTR xxdB”.

Press +/– to adjust the centre speaker level.

• Press MENU < or > repeatedly to select “REAR

xxdB”.

Press +/– to adjust the rear speaker level.

You can select a volume level of -15 dB to +10 dB in

1-dB steps.

You can adjust the volume level of the sub woofer

• Press LEVEL or CURSOR MODE on the remote

repeatedly until the LEVEL indicator lights up.

• Press MENU < or > repeatedly to select “SW xxdB”.

• Press +/– to adjust the level.

You can select a volume level of -15 dB to +10 dB in

1-dB steps.

You can increase the output level of the rear

speakers

The adjustment range of the rear speakers is preset from

–15 to +10, but you can shift the range up 5 levels (–10

to +15).

• Press SET UP.

• Press MENU < or > repeatedly until “REAR SET UP”

appears on the display.

• Press +/– repeatedly until “NORMAL” appears on

the display.

The values for the rear level remain fixed at –15 to +10

in the display, but you will be able to hear the difference

in the actual output level.

To reset the rear level adjustment range, repeat this

procedure to display “GAIN LOW”.

You can reset all sound field settings to initial

setting

• Turn off the receiver.

• Hold down SOUND FIELD ON/OFF and then press

?/1 (power).

All sound field settings will be cleared and set to sound

field off.

5 Press +/– repeatedly until the centre mode you

want appears on the display. Select the centre

mode as follows:

Adjusting the speaker volume

The test tone feature lets you set the volume of your

speakers to the same level. (If all of your speakers have

equal performance, you don’t have to adjust the

speaker volume.)

Using the controls on the remote lets you test the

speaker connection and adjust the volume level from

your listening position.

1 Press SOUND FIELD ON/OFF to turn on the

sound field.

Press SOUND FIELD MODE +/– repeatedly to

select “DOLBY PL”.

2 Press TEST TONE on the remote.

You will hear the test tone from each speaker

sequentially.

3 Adjust the volume level so that the volume of test

tone from each speaker sounds the same when

you are in your main listening position.

• Press MENU < or > to select “CTR xxdB” or

“REAR xxdB”.

• Press +/– to adjust the level.

4 Press TEST TONE on the remote to turn off the

test tone.

If you have

Front and rear

speakers, and a

small centre

speaker

Front and centre

speakers, no rear

speaker

Front and rear

speakers, no

centre speaker

Front and rear

speakers, and a

large centre

speaker

So that

The bass sound of the

centre channel is

output from the front

speakers (because a

small speaker cannot

produce enough

bass).

The sound of the rear

channel is output

from the front

speakers.

The sound of the

centre channel is

output from the front

speakers.

The centre channel

fully reproduces the

entire audio

spectrum.

Select

NORMAL

3 STEREO

(3 Channel Logic)

PHANTOM

WIDE

Strona jest ładowana ...

Sony STR-DE345 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Sony STR-DE345 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty