Sony ST-SE500 Instrukcja obsługi

Marka: Sony

Model: ST-SE500

Kategoria: Tunery audio

Typ: Instrukcja obsługi

FM Stereo

FM-AM Tuner

3-865-570-31(1)

Operating instructions

Instrukcja obsługi

Инструкция по эксплуатации

ST-SE500

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to qualified

personnel only.

Precautions

On safety

• Should any liquid or solid object fall

into the unit, unplug the unit and

have the unit checked by qualified

personnel before operating it any

further.

On power sources

• Before operating the unit, be sure that

the operating voltage of your unit is

identical with that of your local

power supply.

• Unplug the unit from the wall outlet

if it is not to be used for an extended

period of time. To disconnect the

cord, pull it out by grasping the plug.

Never pull the cord itself.

• AC power cord must be changed only

at the qualified service shop.

On placement

• Place the unit in a location with

adequate ventilation to prevent heat

buildup and prolong the life of its

components.

• Do not place the unit near heat

sources, or in a place subject to direct

sunlight, excessive dust or

mechanical shock.

• Do not place anything on top of the

cabinet which might block the

ventilation holes and cause

malfunctions.

• Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

On cleaning the cabinet

• Clean the cabinet, panels and controls

with a soft cloth lightly moistened

with a mild detergent solution. Do

not use any type of abrasive pad,

scouring powder or solvent such as

alcohol or benzine.

On repacking

• Do not throw away the carton and the

packing material. This makes an

ideal container when transporting the

unit. When shipping the unit, repack

it as it was packed at the factory.

If you have any question or problem

concerning your unit that is not covered

in this manual, please consult your

nearest Sony dealer.

TABLE OF CONTENTS

Getting Started

Unpacking 4

Hooking up the System 4

Selecting the German Display 6

Storing FM Stations Automatically (Auto-betical select) 6

Basic Operations

Receiving Preset Stations 7

Advanced Tuner Operations

About the Menu Entry System 8

Customizing the Display 8

Receiving Broadcasts 9

Tips for Better FM Reception 10

Presetting Radio Stations 10

Naming the Preset Stations 11

Organizing the Preset Stations 12

Using the Radio Data System (RDS) 13

Additional Information

Troubleshooting 15

Specifications 15

Index 16

Welcome!

Thank you for purchasing the Sony FM

Stereo FM/AM Tuner. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

Convention

The following icon is used in this

manual:

Indicates hints and tips for

making the task easier.

Unpacking

Check that you received the following items with the

tuner:

• Audio cord (1)

• AM loop aerial (1)

• FM wire aerial (1)

• EON connecting cord (1)

Getting Started

around the frame of the aerial. Be careful to

unwrap only the braided section of the lead wire.

Do not unwrap more than 3 lengths of the lead

wire. Also, be careful not to unbraid the lead wire.

3 Assemble the supplied aerial as shown below.

4 Connect the AM loop aerial to the AM terminals

on the back of this unit.

5 Adjust the aerial direction for the best reception.

The AM loop aerial has a directivity which detects

the signal from some angles more strongly than

others. Set the aerial to the orientation which

provides the best receiving condition.

If a high pitched noise (beat noise) occurs when

recording AM broadcasts, adjust the position of

the AM loop aerial so that the noise disappears.

If you live in a building constructed of reinforced

concrete, or with a steel frame, you may not be

able to achieve good reception since the radio

waves become weaker indoors. In this case, we

recommend connecting an optional aerial such as

the Sony AN-1.

For stations that are difficult to receive

Try repositioning the loop aerial while tuning. Placing

the supplied AM loop aerial near a window will help

improve reception quality.

Hooking up the System

Before you get started

• Turn off the power to all components before making

any connections.

• Do not connect the mains lead until all of the

connections are completed.

• Be sure to make connections firmly to avoid hum and

noise.

• When connecting an audio cord, be sure to match the

colour-coded pins to the appropriate jacks: White

(left) to White; and Red (right) to Red.

AM aerial hookups

This section describes how to connect the supplied AM

loop aerial. For the specific location of the AM

ANTENNA terminals, see the illustration below.

What will I need?

• AM loop aerial (supplied) (1)

1 Before assembling the supplied aerial, pull the

lead wire out from the slot in the aerial frame.

2 Unwrap 3 lengths of the braided lead wire from

AM loop aerial

ANTENNA

75 COAXIAL

AM ANTENNA

FM aerial hookups

With an FM outdoor aerial, you can obtain a higher FM

broadcast sound quality. We recommend that you use

the supplied FM wire aerial only temporarily until you

install an FM outdoor aerial. For the specific location of

the FM ANTENNA terminal, see the illustration below.

What will I need?

• FM wire aerial (supplied) (1)

• FM outdoor aerial (not supplied) (1) and 75-ohm coaxial

cable with IEC female type connector (not supplied) (1)

Connect the supplied FM wire aerial or an FM outdoor

aerial (not supplied) to one of the FM terminals on the

back of this unit.

Connecting a ground wire

If you connect an outdoor aerial, be sure to connect a

earth lead (not supplied) to the AM ANTENNA y

terminal (in addition to the AM loop aerial) for

lightning protection.

Getting Started

FM ANTENNA

IEC female type connector

Amplifier hookups

Connect the tuner to an amplifier. Be sure to turn off

the power to both components before connection. For

the specific location of the terminals, see the illustration

below.

What cables will I need?

• Audio cord (supplied) (1)

Connect the white plugs to the white (L) jacks and the red

plugs to the red (R) jacks. Insert the plugs completely into

the jacks; incomplete connections may cause noise.

EON CONTROL

Red (R)

White (L)White (L)

Red (R)

TUNER IN

LINE OUT

Amplifier

Tuner

If you have a Sony amplifier equipped with an EON

CONTROL IN terminal

Use the supplied EON connecting cord to connect the

EON CONTROL OUT terminal on the tuner to the EON

CONTROL IN terminal on your amplifier. This lets you

use the EON function (see page 13) when listening to

other components.

Mains lead hookup

Connect the mains lead to a wall outlet after completing all

of the previous connections.

Amplifier

Tuner

EON CONTROL

OUT

EON CONTROL

ANTENNA

75 COAXIAL

FM wire aerial

ANTENNA

75 COAXIAL

FM outdoor aerial

IEC female type

connector

LINE OUT

to a wall

outlet

Storing FM Stations

Automatically

(Auto-betical select)

With “Auto-betical select” you can automatically store

up to 30 FM and FM RDS stations in alphabetical order

without redundancy. Additionally, “Auto-betical

select” only stores the stations with the clearest signals.

If you want to store FM or AM (MW and LW) stations

one by one, see “Receiving Broadcasts” on page 9 and

“Presetting Radio Stations” on page 10.

1 Press POWER to turn on the tuner.

2 Turn on the amplifier and select the TUNER

mode.

3 Press AUTO-BETICAL SELECT.

“Yes” and “No” appear in the display.

4 Turn TUNING/SELECT to select “Yes”.

5 Press AUTO-BETICAL SELECT again.

The tuner scans and stores all the FM and FM

RDS stations in the broadcast area.

For RDS stations, the tuner first checks for

stations broadcasting the same programme, then

stores only the one with the clearest signal. The

selected RDS stations are sorted alphabetically by

their Programme Service name, then assigned a

two-character preset code. For more details on

RDS, see page 13.

Regular FM stations are assigned two-character

preset codes and stored after the RDS stations.

To change the location of, or erase, a preset station

See “Organizing the Preset Stations” on page 12.

Notes

• If you move to another area, repeat this procedure to store

stations in your new area.

• For details on tuning stored stations, see page 7.

• The FM MODE setting is also stored along with the

station.

• If you move the aerial after storing stations using "Auto-

betical select," the stored settings may no longer be valid.

If this happens, store the stations again.

Getting Started

Selecting the German Display

You can choose either an English or a German

language display. The factory preset language is

English. To change the display to German, follow the

steps below.

1 Press POWER to turn off the tuner.

2 While holding down the “2” button, press

POWER to turn on the tuner .

“Deutsch” appears in the display.

To return to the English display

Repeat this procedure.

“English” appears in the display.

POWER

AUTO-BETICAL SELECT

TUNING/SELECT

POWER

Make sure you’ve hooked up the tuner and preset stations.

(See pages 4 - 5 for hookups and page 6 or 10 for presetting.)

Turn on the amplifier and select the TUNER mode.

Press POWER to turn on the tuner.

Press SHIFT to select A, B, or C.

Press the preset number you want (1 - 0).

Receiving Preset Stations

This section shows you how to receive preset stations.

To check broadcasts by scanning the preset stations

• To tune in a non-preset

station, see “Receiving

Broadcasts” on page 9.

Basic Operations

POWER

EON Link System

AUTO-BETICAL

SELECT

MEMORY FM MODE BAND

TA NEWS/INFO PTY DISPLAY

EON

SHIFT 1 2 3 4 5 6 7 8 9 0 DIRECT

MENU RETURN

CHARACTER TUNE MODE

TUNING/ SELECT

ENTER

FM STEREO/FM-AM TUNER ST-SE500

1Press TUNE MODE repeatedly so that “PRESET” appears in the display.

2 Turn TUNING/SELECT.

Each time you turn TUNING/SELECT, a preset station is received and

the settings (preset code, frequency, and station name, etc.) appear in the

display. The signal meter indicates the strength of the broadcast signal.

0 DIRECT

MENU RETURN

CHARACTER TUNE MODE

TUNING/ SELECT

ENTER

FM STEREO/FM-AM TUNER ST-SE5 00

TUNING/SELECT

TUNE MODE

About the Menu Entry System

This tuner uses a menu entry system which allows you

to operate various functions by following messages on

the display. Use the following controls for menu

operation.

Advanced Tuner Operations

TUNING/SELECT

ENTER

RETURN

Use the

MENU button

TUNING/SELECT knob

ENTER button

RETURN button

To:

enter the menu mode.

display different items or

settings.

select the currently displayed

item or setting.

return to a previous stage in the

menu mode.

Customizing the Display

You can choose the appearance of the display from one

of the following four display modes.

1 Press MENU, then turn TUNING/SELECT until

“Disp-Mode” appears in the display.

2 Press ENTER.

“Select” appears in the display.

3 Turn TUNING/SELECT to select a display mode.

Full Display/Full Brightness

Full Display/Dimmed

Minimal Display/Full Brightness

Minimal Display/Dimmed

4 Press ENTER.

The setting remains in effect until you change it

again.

If you press one of the buttons on the main unit,

the minimal display changes to the full display

with the selected brightness. After about 4

seconds, the display returns to the display mode

you selected.

TUNING/SELECT

ENTER

Receiving Broadcasts

This tuner lets you enter a station’s frequency directly

by using the numeric buttons (direct tuning). If you

don’t know the frequency of the station you want, see

“Receiving broadcasts by scanning stations (Automatic

tuning)”.

Before you begin, make sure you have:

• Connected an FM/AM aerial to the tuner as

indicated on page 4.

1 Press BAND to select FM, MW, or LW.

2 Press DIRECT.

3 Press the numeric buttons to enter the frequency.

Example 1: FM 102.50 MHz Example 2: AM 1350 kHz

To receive other stations

Repeat Steps 1 to 3.

When you tune in AM (MW and LW) stations

Adjust the direction of the AM loop aerial for optimum

reception.

If the STEREO indicator remains off

Press FM MODE when an FM stereo broadcast is

received.

If an FM stereo programme is distorted

The STEREO indicator flashes. Press FM MODE to

change to monaural (MONO). You will not have the

stereo effect but the distortion will be reduced. To

return to stereo mode, press this button again.

If you cannot tune in a station and the entered

numbers are flashing

Make sure you’ve entered the right frequency. If not,

press DIRECT and reenter the frequency you want.

If the entered numbers still flash, the frequency is not

used in your area.

If you enter a frequency not covered by the tuning

interval

The entered value is automatically rounded up or down

to the closest covered value.

Tuning intervals for direct tuning are:

FM: 50 kHz intervals

AM: 9 kHz intervals (MW), 1 kHz interval (LW)

Receiving broadcasts by scanning stations

(Automatic tuning)

With automatic tuning you can quickly tune in a

station without having to know its frequency.

1 Press BAND to choose either FM, MW, or LW.

2 Press TUNE MODE so that “AUTO TUNING”

appears in the display.

3 Turn TUNING/SELECT slightly and release it

when the frequency numbers start changing.

Turn the knob to the right for a higher frequency;

turn it to the left for a lower frequency.

When the tuner locates a station, it stops

automatically, “TUNED” appears in the display.

The signal meter indicates the strength of the

broadcast signal.

4 Repeat step 3 until you tune in the appropriate

station.

To store the station, see “Presetting Radio

Stations” on page 10.

If you cannot tune in the station you want(Manual

Tuning)

With manual tuning you can search through all stations

broadcasting on each band, and tune in stations with

extremely weak signals that you might not be able to

receive with automatic tuning.

1 Press BAND repeatedly to choose FM, MW, or LW.

2 Press TUNE MODE so that only “TUNING” appears

in the display. “AUTO” should not appear in the

display.

3 Turn TUNING/SELECT until you tune in the desired

station.

Turn the knob to the right for a higher frequency;

turn it to the left for a lower frequency.

The signal meter indicates the strength of the

broadcast signal.

Note

When you reach the highest or lowest frequency of any

band, tuning stops.

Advanced Tuner Operations

Numeric

buttons

BAND DIRECT

1 0250

1350

Advanced Tuner Operations

Presetting Radio Stations

This section shows you how to store up to 30 of your

favorite FM or AM (MW and LW) stations manually

onto preset codes made up of characters (A, B, or C)

and numbers (1-0), such as A7. You can store up to 10

stations on each of the 3 different letters. You can use

these letters to classify stations according to music

category or station band.

1 Tune in the FM, MW, or LW station you wish to

store.

2 Press MEMORY.

“MEMORY” appears along with the lowest

vacant code to indicate that the tuner is ready to

store the station.

3 Press SHIFT to chose either A, B, or C.

The letter you choose appears in the display.

4 Press a numeric button (1-0).

The tuner stores the station at the preset code you

specified.

5 Repeat steps 1 through 4 to store other stations.

RDS Station names are stored automatically

When you preset an RDS station broadcasting station

name information, the station name is automatically

stored at the station preset.

If you want to label the stations

Follow the procedure described in “Naming Preset

Stations” on page 11.

Numeric

buttons

MEMORY SHIFT

Tips for Better FM Reception

This tuner has two functions designed for better

reception, the FM mode setting and the digital signal

meter. First, try to receive stations with the standard

settings. If the reception is not good, try altering the

reception quality to obtain a clear signal. The tuner

stores the FM mode setting, together with the

frequency when you make a station preset.

Setting the FM mode

Press FM MODE a few times to choose the reception

mode, select either Auto stereo (no indication) or

MONO.

• Auto stereo mode receives stereo broadcasts with

strong signals. Press FM MODE a few times so that

“MONO” disappears.

• “MONO” receives stations with weak signals.

Stations will be received in monaural but with even

less noise.

Checking the signal strength

You can use the digital signal meter to check the signal

strength of FM frequencies. The display range is from

16 to 70 dB (1µV of radio frequency voltage = 0dB). To

obtain a signal to noise ratio sufficient for receiving a

stereo broadcast, we recommend a reading greater

than 50 dB. (You can also change the FM MODE while

using the signal meter to determine the best reception.)

1 Tune in an FM station.

2 Press DISPLAY repeatedly to display the digital

signal meter.

3 Rotate the FM aerial to obtain the strongest signal.

DISPLAY

FM MODE

Advanced Tuner Operations

Naming the Preset Stations

You can assign a name up to 13 characters long to each

preset station except FM RDS stations. When the

station is tuned in, the station name will appear instead

of the frequency.

1 Press CHAR.

The cursor blinks in the display.

2 Turn TUNING/SELECT to select a character.

3 When the character you want appears, press

CHAR to move the cursor into position for the

next character.

If you make a mistake

Press CHAR repeatedly until the character you want to

change flashes (every time you press CHAR, the next

character flashes). Then turn TUNING/SELECT to

select a new character.

4 Repeat steps 2 and 3 until the station name you

desire appears in the display.

5 Press MEMORY.

“MEMORY” appears along with the lowest

vacant code to indicate that the tuner is ready to

store the station.

6 Press SHIFT and one of the preset buttons to

specify the preset where you want to store the

station name.

Note

The display returns to normal display mode if you stop

assigning names for more than 8 seconds. If this happens,

start again from the beginning.

To see the frequency of the displayed station name

Press DISPLAY repeatedly.

Numeric

buttons

MEMORY SHIFT

DISPLAY

CHAR TUNING/SELECT

Moving preset station

You can also move a specific preset station.

1 Follow steps 1 through 3 in “Organizing the

Preset Stations” and choose “Move” from the Edit

menu, then press ENTER.

2 Turn TUNING/SELECT so that the preset code

you want to move appears in the display and

press ENTER.

3 Turn TUNING/SELECT to select the new location

for the preset code and press ENTER.

The preset station you selected is moved to the

new location and the other preset stations in that

group (“A” for example) shift backwards to make

room for the new preset.

EXAMPLE:

If you move A4 to A1.

Erasing preset stations

You can erase preset stations one by one.

1 Follow steps 1 through 3 in “Organizing the

Preset Stations” and choose “Erase” from the Edit

menu, then press ENTER.

2 Turn TUNING/SELECT so that the preset code

you want to erase appears in the display and

press ENTER.

The preset station you selected is erased from the

preset memory and the other preset stations in

that group (“A” for example) shift forward to fill

in the blank space.

EXAMPLE:

If you erase A1.

If you want to erase all the preset stations

1 Turn off the power

2 While holding down the number 5 button and

AUTO-BETICAL SELECT, press POWER to turn on

the power.

Advanced Tuner Operations

89.5 94.5 96.5 98.0 100.5 103.0 104.5 106.0Frequency

A1 A2 A3 A4 A5 A6 A7 A8Preset

98.0 89.5 94.5 96.5 100.5 103.0 104.5 106.0Frequency

A1 A2 A3 A4 A5 A6 A7 A8Preset

89.5 94.5 96.5 98.0 100.5 103.0 104.5 106.0Frequency

A1 A2 A3 A4 A5 A6 A7 A8Preset

94.5 96.5 98.0 100.5 103.0 104.5 106.0Frequency

A1 A2 A3 A4 A5 A6 A7 A8Preset

change the location of a specific preset (see

below).

erase a specific preset (see below).

sort preset stations in alphabetical order

according to their preset names.

Stations without preset names are arranged

by frequency, from low to high.

sort preset stations in order of their signal

strength (FM stations only).

MW and LW frequencies are arranged by

frequency.

sort FM RDS stations with PI information

alphabetically by country.

Other stations are arranged by frequency.

sort preset stations in order of their

frequency band (FM - MW - LW).

TUNING/SELECT

ENTER

Choose

Move

Erase

Alphabet

Strength

Country

Band

Organizing the Preset Stations

This tuner makes it easy to arrange preset stations in

the order you prefer. You can arrange all the preset

stations automatically, according to alphabetical order,

signal strength, country code, or tuner band, or you

can use the “Move” and “Erase” functions to move and

erase specific preset stations.

1 Press MENU.

2 Turn TUNING/SELECT until “Edit” appears in

the display and press ENTER.

If no stations have been stored as presets, “No

Preset” appears in the display.

3 Turn TUNING/SELECT to choose one of the

following sorting methods:

4 Press ENTER.

The tuner sorts the stations, then returns to

normal tuning mode and receives preset station

A1.

Note

Some countries use the same country code, and the stations

from these counties may be arranged together.

Notes

• If there is an emergency announcement by governmental

authorities, “ALARM” flashes in the display.

• If a station is not providing a particular RDS service,

“NO...” (such as “NO PTY”) appears in the display.

• When a station broadcasts radio text data, the display

shows the data at the rate it is sent from the station. The

display speed changes in relation to the speed at which

the data is sent.

Monitoring traffic, news, or information

programmes (EON)

Enhanced Other Networks (EON) allows the tuner to

automatically switch to a station broadcasting traffic,

news, or information. After the programme ends, the

tuner switches back to the station you were listening

to. To use this function, be sure to store the stations

beforehand.

To monitor traffic programmes

1 Tune to a preset FM RDS station so that the RDS

TP, or RDS TP EON indicators light in the

display.

2 Press TA so that “TA” appears in the display.

Each time you press TA, the display changes as

follows:

TA (Traffic Announcement) , OFF

When the tuner automatically tunes in a traffic

programme, the TA indicator flashes. If you do

not want to listen to the entire programme, press

TA to switch back to the original station.

To monitor news and/or information programmes

1 Tune to a preset FM RDS station so that the RDS

TP or RDS TP EON indicators light in the display.

2 Press NEWS/INFO so that either the NEWS or

INFO indicator, or both the NEWS and INFO

indicators, appear in the display.

Each time you press NEWS/INFO, the display

changes as follows:

/ NEWS / INFO / NEWS/INFO / OFF

When the tuner automatically tunes in a news or

information programme, the respective indicator

flashes. If you do not want to listen to the entire

programme, press NEWS/INFO to switch back to

the original station.

Using the Radio Data System

(RDS)

What you can do with RDS

The Radio Data System (RDS) is a broadcasting service

that allows radio stations to send additional

information along with the regular radio programme

signal. This tuner offers you three convenient RDS

features: Displaying the RDS information; Monitoring

of traffic, news, or information programmes; and

Locating a station by programme type. RDS is

available only on FM stations.*

Note

RDS may not work properly if the station you are tuned to is

not transmitting the RDS signal properly or if the signal

strength is weak.

* Not all FM stations provide RDS service, nor do they

provide the same types of services. If you are not familiar

with the RDS system, check with your local radio stations

for details on RDS services in your area.

Receiving RDS broadcasts

Simply select a station from the FM band.

When you tune in a station that provides RDS services,

the RDS indicator and the station name appears in the

display.

Displaying the RDS information

Press DISPLAY repeatedly until the information you

desire is displayed.

* This information also appears for non-RDS FM stations.

Advanced Tuner Operations

You can:

Locate each station by name

(e.g., WDR) instead of

frequency.

Locate each station by

frequency.

Display the current time.

Locate a specific type of

programme being broadcast.

(See page 14 for the types of

programmes you can select.)

Display the text messages sent

by the RDS station.

Determine each broadcast's

country of origin.

(See page 10 for details.)

Information displayed

Station Name*

Frequency*

Clock Time

(24 hour system)

Programme Type

Radio Text

Programme Identification

Digital signal meter*

(continued)

To stop monitoring the programme

Press TA or NEWS/INFO while the tuner is in the respective

EON standby mode and the indicator goes out.

Notes

• If you tune in an AM (MW/LW) station or an FM station

which does not provide the RDS service, the selected

indicator (TA, NEWS, INFO, or NEWS/INFO) goes off

and the tuner does not standby for EON stations.

• “Weak Signal” appears when the selected station has a

weak signal. “Return” appears when the tuner is trying to

retune a station with a weak signal.

• Turn off the EON feature when you want to record a

programme without interruptions, especially when you

want to do timer recording.

• “No EON” appears in the display if you select an EON

programme before tuning to an RDS station.

• If you make EON CONTROL connections to a compatible

Sony amplifier, the amplifier automatically switches the

function mode to TUNER whenever the tuner receives a

programme you are monitoring.

Locating traffic programmes (TA search)

You can have the tuner locate stations currently

broadcasting traffic programme from among the RDS

stations stored in the tuner's preset memory.

1 Press MENU.

2 Turn TUNING/SELECT until “Traffic” appears in

the display and press ENTER.

The unit enters search mode (“Search” and

“Traffic” appear alternately in the display).

When the tuner finds a traffic announcement, it

stops searching. The tuner receives each station

for 8 seconds.

3 Press ENTER when the tuner receives the station

you desire to listen to that programme.

Locating a station by programme type

(PTY)

You can locate a station you want by selecting a

programme type. The tuner tunes in the type of

programmes currently being broadcast from the RDS

stations stored in the tuner's preset memory.

1 Press PTY.

2 Rotate TUNING/SELECT to select the

programme type you want. See the following

table for the programme types you can select.

Advanced Tuner Operations

3 Press PTY.

The tuner starts searching the preset RDS stations

for the programme (“Search” and the programme

type are displayed alternately).

When the tuner finds the programme you are

looking for, it stops searching. The preset stations

currently broadcasting the selected programme

type are indicated and the tuner receives each

station for 8 seconds.

4 Press PTY when the tuner receives the station you

desire to listen to that programme.

What you hear

Topical programmes that expand on

current news

Emergency broadcasts

Programmes about national or regional

culture, such as religion, language, and

societal concerns

Radio plays and serials

Educational programmes, such as a

“how-to” programme and advice

Programmes about consumer affairs,

medical advice, and weather

Classical music, such as instrumental,

vocal, and choral works

Easy Listening (middle of the road music)

News programmes

Music that does not fit into any of the

above categories, such as jazz and

rhythm and blues

Popular music programmes

Any programmes not defined above

Rock music programmes

Programmes about the natural sciences

and technology

Sports programmes

Performances of major orchestras,

chamber music, opera, etc.

Other types of programmes such as,

celebrity interviews, panel games, and

comedy

Programme

type

Affairs

Alarm

Culture

Drama

Education

Information

L. Classical

M.O.R.Music

News

Other Music

Pop Music

PTY

undefined

Rock Music

Science

Sports

S. Classical

Varied

Troubleshooting

If you experience any of the

following difficulties while using

the tuner, use this troubleshooting

guide to help you remedy the

problem. Should any problem

persist, consult your nearest Sony

dealer.

There’s no sound.

/ Connect the aerials.

/ Set the source setting on

the amplifier to TUNER.

You cannot tune in a frequency.

/ Adjust the position of the

aerial.

/ Connect an external aerial

for FM broadcasts.

/ Preset the stations again if

you've moved.

There is severe hum and/or

background noise.

/ Adjust the position or

direction of the aerial.

/ Tune to a correct

frequency.

/ Connect an external aerial

for FM broadcasts.

/ Move the tuner away from

the source of the noise.

RDS isn‘t working.

/ Make sure that you are

tuned to an FM station.

/ Select a stronger FM

station.

“No preset” appears in the display.

/ If the mains lead is

disconnected from the wall

outlet for more than one

month, the memory is

erased. Preset stations

again.

The station was interrupted by

another station / The tuner

automatically starts searching

stations.

/ The EON function is

working. Turn off EON

when you don't want the

current programme

interrupted.

The appropriate display or

information does not appear.

/ Turn the power off. Press

and hold AUTO-BETICAL

SELECT and the 5 button

and press POWER to turn

the power back on. This

empties any frequencies

stored in the preset

memory and returns the

display to the default

language (English).

/ Contact the radio station

and find out whether or

not they actually provide

the service in question. If

so, the service may be

temporarily out of order.

Additional Information

Frequency response

Separation

Selectivity

30 Hz - 15 kHz

(+0.5/–1.0 dB)

40 dB at 1 kHz

at 400 kHz

80 dB

at 300 kHz

60 dB

Output

Frequency range

Intermediate frequency

Usable Sensitivity

Signal-to-noise ratio

Harmonic distortion

Selectivity

Power requirements

Power consumption

Input impedance

Input connector

Dimensions

Weight

Supplied accessories

at 40 kHz deviation

600 mV

MW: 522 - 1,611 kHz

(9 kHz step)

LW: 144 - 288 kHz

(1 kHz step)

450 kHz

(with AM loop

aerial)

MW: 300 µV/m

LW: 1 mV/m

MW: 54 dB

(50 mV/m,

999 kHz)

LW: 50 dB

(50 mV/m,

216 kHz)

0.3% (50 mV/m,

400 Hz)

32 dB

220-230 V, AC

50/60 Hz

10 W

75 ohms

IEC-male

430 x 82 x 295 mm

(w/h/d)

2.7 kg

Audio cord (1)

AM loop aerial (1)

FM wire aerial (1)

EON control cord (1)

AM tuner section

General

Design and specifications are subject to

change without notice.

Specifications

FM tuner section

Frequency range

Aerial terminals

Intermediate frequency

65.0 - 74.0 MHz

87.5 - 108.0 MHz

75 ohms,

unbalanced

10.7 MHz

Sensitivity

Usable sensitivity (IHF)

S/N

Harmonic distortion

at 26 dB quieting

(mono) 10.3 dBf,

0.9 µV/75Ω

at 46 dB quieting

(stereo) 38.5 dBf,

23 µV/75Ω

10.3 dBf, 0.9 µV/

75Ω

at 40 kHz deviation

74 dB (mono),

69 dB (stereo)

0.1 % (mono),

0.2 % (stereo)

Additional Information

Index

A, B

Aerial hookups

AM 4

FM 5

Amplifier hookups 5

Automatic tuning 9

Auto-betical select 6

Connecting. See Hookups

Display

language 6

mode 8

EON 13

F, G

FM mode 10

H, I, J, K, L

Hookups

AM aerial 4

amplifier 5

FM aerial 5

mains lead 5

Manual tuning 9

Memory 6, 10, 11

Naming stations 11

Organizing preset stations 12

P, Q

Presetting

AM stations 10

FM stations 6, 10

Preset tuning

AM stations 7

FM stations 7

PTY 14

RDS 13

Receiving preset stations 7

Signal meter 10

Storing radio stations. See

Presetting

Troubleshooting 15

Tuning. See Receiving

broadcasts

U, V, W, X, Y, Z

Unpacking 4

OSTRZEŻENIE

Aby nie zapobiec do pożarowi lub

porażeniu prądem elektrycznym, należy

chronić urządzenie przed deszczem lub

działaniem wilgoci.

Aby uniknąć porażenia prądem

elektrycznym, nie należy otwierać

obudowy. Naprawy urządzenia należy

powierzać specjalistom.

O ponownym pakowywaniu

• Nie wyrzucaj kartonu i innych

materiałów opakunkowych. Można je

będzie użyć jako idealnego

opakowania podczas przewozu

urządzenia. W przypadku wysyłki

urządzenia zapakuj je tak, jak było

zapakowane fabrycznie.

Jeżeli zaistnieją jakiekolwiek problemy

lub wątpliwości dotyczące niniejszego

urządzenia, o których nie ma mowy w

instrukcji obsługi, zwróć się po poradę

do najblizszego punktu sprzedaży

sprzętu Sony.

Ostrzeżenia

O bezpieczeństwie

• Jeżeli jakikolwiek płyn lub przedmiot

dostanie się do wnętrza urządzenia,

wyjmij wtyczkę z gniazdka i przed

ponownym użyciem zleć sprawdzenie

urządzenia kwalifikowanemu

personelowi.

O źródłach zasilania

• Przed rozpoczęciem użytkowania

upewnij się, że napięcie

eksploatacyjne twojego urządzenia

odpowiada napięciu w sieci lokalnej.

• Jeżeli urządzenie ma być nie

używane przez dłuższy okres czasu,

wyłącz wtyczkę z gniazdka

ściennego. Aby odłączyć przewód,

pociągnij ujmując za wtyczkę. Nigdy

nie ciagnij za sam przewód.

• Wymiana kabla zasilania może być

dokonana jedynie w kwalifikowanym

punkcie usługowym.

O lokalizacji

• Ustaw urządzenie w miejscu

zapewniającym wystarczającą

wentylację, aby uniknąć przegrzania

urządzenia i w ten sposób przedłużyć

możlliwy okres eksploatacji jego

elementów.

• Nie umieszczaj urządzenia w pobliżu

źródeł ciepła lub w miejscu

nasłonecznionym, szczególnie

zakurzonym lub narażonym na

wstrząsy mechaniczne.

• Nie umieszczaj na wierzchu

obudowy nic, co mogłoby blokować

wentylację i powodować wadliwe

funkcjonowanie.

• Nie instaluj urządzenia w przestrzeni

obudowanej, takiej jak półka na

książki, czy wbudowana szafka.

Czyszczenie

• Obudowę, płytę czołową i regulatory

czyść miękką ściereczką lekko

zwilżoną łagodnym detergentem. Nie

używaj szorstkiej tkaniny, proszku

czyszczącego oraz środków takich

jak alkohol czy benzyna.

SPIS TREŚCI

Czynności wstępne

Rozpakowanie 4

Podłączanie zestawu 4

Wybór wyświetlenia w języku niemieckim 6

Wprowadzanie do pamięci stacji FM automatycznie (Wybór auto-

betyczny) 6

Działania podstawowe

Odbiór wprowadzonych do pamięci stacji 7

Zaawansowane działania tunera

O systemie korzystania z menu 8

Wybór rodzaju wyświetlenia 8

Odbiór programów 9

Wskazówki dla lepszego odbioru FM 10

Programowanie stacji radiowych 10

Nadawanie nazw zaprogramowanym stacjom 11

Porządkowanie zaprogramowanych stacji 11

Korzystanie z systemu danych radiowych (RDS) 13

Dodatkowe Informacje

W razie trudności 15

Dane techniczne 15

Indeks 16

Witaj !

Dziękujemy za zakup stereofonicznego

tunera FM/AM produkcji firmy Sony.

Przed rozpoczęciem użytkowania

niniejszego urządzenia prosimy

zapoznać się z instrukcją obsługi i

pozostawić ją w celu odwoływania się

do jej wyjaśnień w przyszłości.

Zasada

W niniejszej instrukcji użyty został

następujący znak:

Oznaczono nim porady i

wskazówki ułatwiające

postępowanie.

Czynności wstępne

Rozpakowanie

Sprawdź, czy wraz z tunerem otrzymałeś następujace

wyposażenie:

• Kabel audio (1)

• antenę ramową AM (1)

• antenę przewodową FM (1)

• kabel podłączeniowy EON (1)

Podłączanie zestawu

Przed rozpoczęciem

• Zanim rozpoczniesz podłączanie wyłącz zasilanie

wszystkich komponentów zestawu.

• Nie podłączaj zasilania z sieci dopóki nie wykonasz

wszystkich połączeń.

• Upewnij się, że połączenia są solidnie wykonane,

aby uniknąć przydźwięku i zakłóceń.

• Podczas podłączania kabla audio upewnij się, że

oznaczone kolorami wtyczki pasują do

odpowiadajacych im gniazdek: białe (lewe) do

białych, a czerwone (prawe) do czerwonych.

Podłączanie anteny AM

Ta część opisuje, jak podłączyć znajdującą się w

wyposażeniu antenę ramową AM. Lokalizację

specjalnych łączy AM ANTENNA sprawdź na poniższej

ilustracji.

AM ANTENNA

Co będzie mi potrzebne ?

• Antena ramowa AM (w wyposażeniu) (1)

1 Przed zamontowaniem anteny wyciągnij przewód

ze szczeliny w ramce anteny.

2 Odwiń trzy długości splecionego przewodu z

ramki anteny. Uważaj, aby odwinąć tylko

splecioną część przewodu. Nie odwijaj więcej niż

trzech długości przewodu. Uważaj także, aby go

nie rozpleść.

3 Zamontuj znajdującą się w wyposażeniu antenę

tak, jak to pokazano poniżej.

4 Podłącz antenę ramową AM do łączy na tyle

niniejszego urządzenia.

5 Wyreguluj kierunek anteny tak, aby osiągnąć

najlepszą jakość odbioru. Antena ramowa AM

posiada kierunkowość wykrywającą sygnał silniej

pod pewnym kątem, a słabiej pod innym. Ustaw

antenę tak, aby zapewnić najlepsze warunki

odbioru. W przypadku wystąpienia dudniena

podczas nagrywania audycji AM, wyreguluj

położenie anteny ramowej AM, aby zlikwidować

zakłócenia. Jeżeli mieszkasz w budynku z

żelbetonu lub o stalowej konstrukcji, uzyskanie

dobrej jakości odbioru może byc niemożliwe,

ponieważ fale radiowe we wnętrzu ulegną

osłabieniu. W takim przypadku polecamy

podłączenie dodatkowej anteny, takiej jak AN-1

produkcji firmy Sony.

Aby odbierać stacje trudne w odbiorze

Próbuj zmieniać ustawienie anteny podczas strojenia.

Ustawienie znajdujacej się w wyposażeniu anteny

ramowej AM w pobliżu okna pomoże uzyskać lepszą

jakość odbioru.

ANTENNA

75 COAXIAL

antena

ramowa AM

Strona jest ładowana ...

Sony ST-SE500 Instrukcja obsługi

Marka: Sony

Model: ST-SE500

Kategoria: Tunery audio

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

русский: Sony ST-SE500 Руководство пользователя

Sony ST-SE500 Instrukcja obsługi

Sony ST-SE500 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty