Bissell 42Q8 Series OPTIclean Instrukcja obsługi

Marka: Bissell

Model: 42Q8 Series OPTIclean

Kategoria: Zgrzewarki próżniowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Earn BISSELL Rewards!

product today!

See details on

back page

Thank You

USER'S GUIDE

42Q8 SERIES

Safety Instructions

Product View

Assembly

Operations

Maintenance and Care

Troubleshooting

Product Registration

Replacement Parts

Consumer Services

6-9

10-12

Accessories

Warranty

Earn BISSELL Rewards!

product today!

See details on

back page

www.bissell.com 800.237.7691

Thanks for buying a BISSELL Vacuum

Thanks for buying a BISSELL OptiClean canister. We’re glad you

purchased a BISSELL vacuum. Everything we know about floor

care went into the design and construction of this complete,

high-tech home cleaning system.

Your BISSELL OptiClean canister vacuum is well made, and

we back it with a limited one year warranty. We also stand

behind it with a knowledgeable, dedicated Consumer Services

department, so, should you ever have a problem, you’ll receive

fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876.

Today, BISSELL is a global leader in the design, manufacture,

and service of high quality homecare products like your

BISSELL OptiClean canister vacuum.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

Chairman, President & CEO

www.bissell.com 800.237.7691

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical

appliance,

basic precautions should be observed,

including the following:

READ ALL

INSTRUCTIONS

BEFORE USING YOUR

CANISTER VACUUM.

Always connect to a polarized outlet

(left slot is wider than right). Unplug

from outlet when not in use and before

conducting maintenance.

WARNING: To

reduce the risk of fire,

electric shock, or injury:

■

Do not leave cleaner when it is

plugged in.

■

Unplug from outlet when not in use

and before servicing.

■

Do not use with damaged cord or plug.

■

To unplug grasp plug not cord.

■

Do not pull or carry by cord, use cord as

a handle, close door on cord, pull cord

around sharp corners, run cleaner over

cord, or expose cord to heated surfaces.

■

Hold plug when rewinding the cord

onto the reel. Do not allow the plug

to whip when rewinding.

■

Do not use cleaner if it has been

dropped, damaged, left outdoors or

dropped into water. Have it repaired

at an Authorized Service Center.

■

Do not allow children to use as a toy.

■

Do not use outdoors or on wet surfaces.

■

Do not handle cleaner or plug with

wet hands.

■

Do not put any object into openings, use

with blocked opening, or restrict air flow.

■

Do not use without dust bag and/or

filters in place.

■

Do not allow hair, loose clothing, fingers

or body parts to get near openings or

floor brush in the appliance.

■

Do not pick up hot coals, cigarette

butts, matches or any hot, smoking,

or burning objects.

■

Do not pick up hard or sharp objects

such as glass, nails, screws, coins, etc.

■

Do not pick up flammable or combus-

tible materials (lighter fluid, gasoline,

kerosene, etc.) or use in the presence

of explosive liquids or vapor.

■

Do not unplug by pulling on cord.

■

Do not pick up toxic material (chlorine

bleach, ammonia, drain cleaner, etc.).

■

Do not use in an enclosed space filled

with vapors given off by oil base paint,

paint thinner, some moth proofing

substances, flammable dust, or other

explosive or toxic vapors.

■

Do not use for any purpose other

than described in this User’s Guide.

■

Always turn off this appliance before con-

necting or disconnecting vacuum hose.

■

Use only manufacturer’s

recommended attachments.

■

Use only on dry, indoor surfaces.

■

Keep openings free of dust, lint, hair, etc.

■

Keep appliance on a level surface.

■

Turn off all controls before plugging

or unplugging cleaner.

■

Be extra careful when cleaning

stairs.

■

Close attention is necessary when

used by or near children.

SAVE THESE

INSTRUCTIONS

FOR FUTURE USE

THIS APPLIANCE

HAS A POLARIZED

PLUG.

To reduce the risk of electric shock,

this appliance has a polarized plug (one

blade is wider than the other). This plug

will fit in a polarized outlet only one

way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to

install a proper outlet. Do not change

the plug in any way.

This model is for household use only.

www.bissell.com 800.237.7691

Power

Button

OnBoard Tool

Storage Lever

Carry Handle

Bag

Change

Indicator

Telescoping

Extension Wand

Dust Bag

Compartment Latch

Swivel Hose

Product view

Flex Hose

Handle

Post-Motor

Filter Compartment

Automatic Cord

Rewind Button

Variable

Suction

Power

Control

WARNING:

Do not plug in your

vacuum until you

are familiar with all

instructions and

operating procedures.

Combination

Dusting Brush/

Upholstery Tool

Crevice Tool

www.bissell.com 800.237.7691

Assembly

1. Connect swivel hose by squeezing both

locking buttons and inserting it into the

suction opening on the canister. Once

the swivel hose is inserted in the suction

opening, release the locking buttons.

2. Connect telescoping extension wand to

the handle end of the flex hose.

3. Connect the floor nozzle foot onto the

telescoping extension wand.

4. To extend the telescopic tube, push the

black release button and then pull the

tube to the desired length.

NOTE: Shorten length of telescopic

tube for storage.

WARNING:

Plastic film packaging can

be dangerous. To avoid

danger of suffocation, keep

away from babies and

children.

www.bissell.com 800.237.7691

Operations

Special tools

Your BISSELL OptiClean canister is

not only a powerful carpet and rug

vacuum cleaner, it’s also a versatile

bare floor and above floor vacuum

cleaner when you select one of the

special tools.

BareFloor tool

Use to vacuum carpets, rugs and

bare floors. Swivel head turns to

get into tight spaces and fits under

cabinets.

1. To vacuum carpets and rugs, push the

brush switch to the carpet position

. This will pull the brushes up into

the floor nozzle.

2. To vacuum bare floors, push the brush

switch to the bare floor position .

This will extend the brushes down from

the floor nozzle.

On-board Tools

The crevice tool and the

combination dusting & upholstery

brush are stored inside the canister

unit. To access them, simply push

down on the Tool Storage Cover

Release. Tools may be attached on

the handle or, where longer reach

is needed, to the extension wand.

Crevice tool

Use the crevice tool in tight, narrow

spaces.

Combination dusting brush/

upholstery tool

1. Use the dusting brush to clean curtains,

draperies, cushions and fabrics

2. Slide the brush off to use the

upholstery tool on cushions, draperies

and fabrics

1. 2.

Brush DownBrush Up

Tip:

Before cleaning under low furniture,

check area first for objects that might

harm the unit or block the hose.

Hair, string and small objects can

block the hose and tools. Check them

occasionally for obstructions.

Crevice Tool

Slide Combo

Brush

www.bissell.com 800.237.7691

Operations

Power cord

The power cord is located at the rear

of the vacuum. Gently pull out the

power cord, watching for the yellow

line. Stop pulling the power cord once

the yellow line is visible. There is also

a red line, which indicates the end of

the usable cord. Do not pull the power

cord out beyond the red line.

Power button

Turn the power ON or OFF by pressing

lightly downward on the power but-

ton ( ).

Automatic cord rewind

Your vacuum is equipped with an

automatic cord rewind. When clean-

ing is finished, press the power button

OFF ( )and grasp the plug to discon-

nect from the electrical outlet. Hold the

plug and press the automatic cord

rewind button to rewind the cord

automatically.

Variable suction power control

The variable suction power control

panel is located on the top of the vac-

uum. Press the

button to increase

suction. Press the – button to decrease

suction, for lightly soiled areas or deli-

cate fabrics.

Power

Button

Automatic

Cord Rewind

CAUTION:

Be careful to avoid injury as

cord retracts very quickly.

CAUTION:

Before using your vacuum,

make sure that the dust

bag and all filters (pre-

motor and post-motor) are

in place. Do not operate

your vacuum without the

dust bag and filters.

Variable Suction

Control

WARNING:

To reduce the risk of electric

shock, turn power switch

OFF and disconnect plug

from electrical outlet before

performing maintenance or

troubleshooting checks.

Bag change indicator

The bag change indicator is located at

the top of the variable suction power

control panel. If the bag change

indicator turns orange while you are

vacuuming, the dust bag needs to be

replaced. The dust bag may appear to

be full or only partially full depending

upon the type of debris picked up.

Fine particles can block the airflow

in the dust bag and reduce suction

before the dust bag is full. If the bag

change indicator remains orange,

even after changing the dust bag, turn

the vacuum off and check for a clog in

the hose or tools.

Operations

Bag Change

Indicator

www.bissell.com 800.237.7691

Dust bag replacement

When disposing of the dust bag,

be sure to follow all steps—the

design of this dust bag allows it to

be sealed prior to removal, thus

eliminating expulsion of dust.

1. Turn the power OFF ( ). Unplug the

vacuum from the electrical outlet.

2. Disconnect the hose.

3. Open the dust bag compartment by

lifting up on the latch located at the

top of the canister, near the carrying

handle.

4. Before removing the vacuum bag, hold

the vacuum bag retainer in place and

pull up on the center tab of the bag to

seal off the dust bag.

5. Once the vacuum bag has been sealed,

remove the vacuum bag by pulling up

on the side tabs and sliding it off the

Vacuum Bag retainer. Dispose of

used bag.

NOTE: Be careful not to throw

away the plastic retainer.

6. Slide the new Vacuum Bag onto the

retainer, with the arrow pointing

downward. Make sure the hose

opening is fully exposed.

7. Ensure that the Vacuum Bag is tucked

fully inside the unit before closing the

canister housing. Press down gently on

the door until it locks into place.

NOTE: The dust bag compartment

door will not close without the

dust bag in place. Attempting to

force the door closed could result

in damage to the machine.

8. Reconnect the hose

Operations

www.bissell.com 800.237.7691

Maintenance and care

The Pre-motor Filter prevents dust

and debris from interfering with

the operation of your vacuum. It

should be regularly checked for

wear or damage and replaced

when torn.

1. Turn the power OFF ( ). Unplug the

vacuum from electrical outlet.

2. Disconnect hose.

3. Open the dust bag compartment by lifting

up on the door latch at the front of the

vacuum. Follow the instructions on page

9 to remove and dispose of the dust bag.

4. Remove the filter frame from the filter hold-

er by gently pressing down on the top tab

and pulling the filter frame up and away

from the filter holder.

5. Remove the filter from the filter frame and

clean by hand washing in warm water.

A mild detergent can be used if desired.

Allow the filter to air dry completely

before replacing.

6. Place the filter back into the filter frame

and replace back into the filter holder,

snapping it back into place.

NOTE: The filter frame should be

placed so that the protective frame

is visible.

7. Following the steps on page 9, replace

the dust bag, making sure the entire back

is tucked in below the seal gasket.

8. Close dust bag compartment door and

press down gently until it locks into place.

9. Reconnect the hose.

NOTICE:

This product is intended for household

use only and not for commercial or

industrial use. Vacuuming of dust

from products like plaster, concrete or

ashes will damage the motor and void

the warranty.

Tip:

For maximum cleaning

performance, check the filters often

and clean or replace if necessary.

WARNING:

Do not operate cleaner with

damp or wet filters or

without all filters in place.

Cleaning the Pre-Motor Filter

Pre-Motor

Filter

www.bissell.com 800.237.7691

Maintenance and care

Cleaning the Post-Motor Filters

HEPA

Media Filter*

The HEPA Media Filter* and the Post-

Motor Filter are located in the back

of your canister, between the power

button and automatic cord rewind. To

access the post-motor filters, lift up on

both of the filter storage tabs to open

the post-motor filter compartment. Both

filters should be regularly checked, and

cleaned if they appear dirty or if you

notice excessive amounts of dust inside

the canister. They need to be replaced if

severely damaged or torn.

Cleaning / Replacing

the HEPA Media Filter*

NOTE: The HEPA Media Filter* is a

white, pleated filter. This filter is NOT

washable. If this filter is damaged or

worn, it will need to be replaced.

1. Unplug the vacuum from the electrical outlet.

2. Lift up on both of the filter storage tabs

to open the post-motor filter compartment.

3. Remove the HEPA Media Filter* by

grasping the lip of the filter frame and

lifting upwards.

NOTE: The HEPA Media Filter*

should not be touched; when

handling be sure to touch only the

white plastic frame.

4. To clean the HEPA Media Filter*, hold over

a trash can and gently tap the frame of the

filter to remove excess dust.

NOTE: If the HEPA Media Filter*

is still excessively dirty, or is

damaged or torn, it will need to

be replaced.

5. Replace the filter in the compartment, with the

white plastic tab facing out.

6. Press down on the filter storage door and snap

back into place to close the filter compartment.

*The filter media, not the vacuum as a whole,

complies with the IEST-RP-CC001.5 or the

EN-1822-1:2009 HEPA standard.

Tip:

For maximum cleaning

performance, check the

filters often and clean or

replace if necessary.

WARNING:

Do not operate cleaner with

damp or wet filters or

without all filters in place.

www.bissell.com 800.237.7691

Maintenance and care

Cleaning the Foam Post-Motor Filter

Foam

Post-Motor Filter

1. Unplug the vacuum from the

electrical outlet.

2. Lift up on both of the filter storage tabs to

open the post-motor filter compartment.

3. The Foam Post-Motor Filter is the black

filter located at the top of the compartment

door. Gently remove this filter.

4. The Foam Post-Motor Filter can be gently

cleaned by washing in warm water with

a mild detergent. Allow filter to dry

completely before reinstalling. If filter is

torn, replace with a new filter.

5. Reinstall filter. Press down on the filter

storage door and snap back into place to

close the filter compartment.

Tip:

For maximum cleaning

performance, check the filters often

and clean or replace if necessary.

WARNING:

Do not operate cleaner with

damp or wet filters or

without all filters in place.

www.bissell.com 800.237.7691

Troubleshooting

Vacuum cleaner won’t run

Possible causes Remedies

1. Vacuum cleaner is not plugged in 1. Check electrical plug

2. Power button is not pressed down 2. Press power button down

Vacuum cleaner won’t pick up or low suction

Possible causes Remedies

1. Tools, hose and/or telescoping extension wands are blocked 1. Remove each part and check for blockages

2. Filters are dirty 2. Check and clean or replace pre-motor and post-motor filters

3. Dust bag is full 3. Replace with new dust bag

4. Swivel hose not securely attached to suction opening 4. Make sure hose connector is locked into

suction opening

5. Crack or hole in flex hose 5. Check hose and replace if needed

6. Air flow regulator or variable suction power 6. Change to closed or maximum setting

control is set to open or minimum setting

Visible dust escaping from vacuum

Possible causes Remedies

1. Dust bag is full 1. Replace with new dust bag

2. Filters missing or installed incorrectly 2. Check pre-motor and post-motor filter for correct installation

3. Filters are dirty 3. Check and clean or replace pre-motor and post-motor filters

4. Flex hose is blocked 4. Remove hose and check for blockages

5. Swivel hose not securely attached to suction opening 5. Make sure swivel hose is locked into suction opening

6. Crack or hole in flex hose 6. Check hose and replace if needed

Other maintenance or service not included in the manual should be

performed by an authorized service representative.

Thank you for selecting a BISSELL product.

Please do not return this product to the store.

For any questions or concerns, BISSELL is happy to be of

service. Contact us directly at 1-800-237-7691.

WARNING:

To reduce the risk of electric

shock, turn power OFF ( ) and

disconnect plug from electrical

outlet before performing mainte-

nance or troubleshooting.

www.bissell.com 800.237.7691

Replacement parts - BISSELL vacuum

Accessories

3 4

5 6

Item Part No. Part Name

1 59H6 Dust Bag Accessory Pack

Includes:

- 5 High Filtration Dust Bags

- 1 Pre-Motor Filter

- 1 HEPA Media Filter*

2 203-7994 Pre-Motor Filter

3 203-7983 Pleated HEPA Media Filter*

4 203-7984 Foam Post-Motor Filter

Item Part No. Part Name

1 203-7998 Floor Nozzle

2 203-7997 Extension Wand

3 203-7991 Crevice Tool

4 203-7992 Combination Dusting Brush/Upholstery Tool

5 203-7996 Hose Assembly

6 203-7993 Dust Bag Holder Assembly

www.bissell.com 800.237.7691

*The filter media, not the vacuum as a whole, complies with the IEST-RP-CC001.5 or the

EN-1822-1:2009 HEPA standard.

Warranty - BISSELL OptiClean

Compact Vacuum

This warranty gives you specific legal rights, and you may also have other rights which may

vary from state to state. If you need additional instruction regarding this warranty or have

questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,

telephone, or regular mail as described below.

Limited One Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product

BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or

products), at BISSELL’s option, free of charge from the date of purchase by the original

purchaser, for one year any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This

warranty does not apply to fans or routine maintenance components such as filters, belts, or

brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any

other use not in accordance with the User's Guide is not covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your

area.

If you need information about repairs or replacement parts, or if you have questions about

your warranty, contact BISSELL Consumer Services.

Website or E-mail:

www.bissell.com

Use the “Customer Support” tab.

Or Call:

BISSELL Consumer Services

1-800-237-7691

Monday - Friday 8 a.m. - 10 p.m. ET

Saturday 9 a.m. - 8 p.m. ET

Or Write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids, MI 49501

ATTN: Consumer Services

BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT

EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR

WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED

ABOVE.

Some states do not allow limitations on how long an implied warranty last so the

above limitation may not apply to you.

www.bissell.com 800.237.7691

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

Grand Rapids, Michigan

Part Number 110-4416

Rev 07/11

Visit our website at:

www.bissell.com

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services

1-800-237-7691

Monday - Friday 8 a.m. — 10 p.m. ET

Saturday 9 a.m. — 8 p.m. ET

Or write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Services

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It

provides proof of purchase date in the event of a

warranty claim. See Warranty on page 15 for details.

BISSELL consumer services

www.bissell.com 800.237.7691

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

Bissell 42Q8 Series OPTIclean Instrukcja obsługi

Marka: Bissell

Model: 42Q8 Series OPTIclean

Kategoria: Zgrzewarki próżniowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

ściągnij PDF

raport

w innych językach

English: Bissell 42Q8 Series OPTIclean User manual

Bissell 42Q8 Series OPTIclean Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Bissell 42Q8 Series OPTIclean Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty