Power Walker VFI 20000CP 3/3L Instrukcja obsługi

EN

Online UPS

PowerWalker VFI 10000CP 3/3

PowerWalker VFI 10000CP 3/3L

PowerWalker VFI 15000CP 3/3

PowerWalker VFI 15000CP 3/3L

PowerWalker VFI 20000CP 3/3

PowerWalker VFI 20000CP 3/3L

PowerWalker VFI 30000CP 3/3

PowerWalker VFI 30000CP 3/3L

Manual

EN, DE, ES, IT, PT, PL

Uninterruptible Power Supply System

EN

Please comply with all warnings and operating

instructions in this manual strictly. Save this

manual properly and read carefully the following

instructions before installing the unit. Do not

operate this unit before reading through all

safety information and operating instructions

carefully.

EN

Table of Contents

1. SAFETY AND EMC INSTRUCTIONS ................................................................................................. 1

1-1. TRANSPORTATION AND STORAGE ............................................................................................................... 1

1-2. PREPARATION ....................................................................................................................................... 1

1-3. INSTALLATION ...................................................................................................................................... 1

1-4. OPERATION ......................................................................................................................................... 2

1-5. STANDARDS ......................................................................................................................................... 2

2. INSTALLATION AND OPERATION .................................................................................................. 3

2-1. UNPACKING AND INSPECTION ................................................................................................................... 3

2-2. REAR PANEL VIEW................................................................................................................................. 4

2-3. SINGLE UPS INSTALLATION ..................................................................................................................... 5

2-4. UPS INSTALLATION FOR PARALLEL SYSTEM .................................................................................................. 8

2-5. SOFTWARE INSTALLATION ....................................................................................................................... 9

3. OPERATIONS ................................................................................................................................ 10

3-1. BUTTON OPERATION ............................................................................................................................ 10

3-2. LED INDICATORS AND LCD PANEL .......................................................................................................... 10

3-3. AUDIBLE ALARM.................................................................................................................................. 12

3-4. SINGLE UPS OPERATION ...................................................................................................................... 12

3-5. PARALLEL OPERATION .......................................................................................................................... 15

3-6. ABBREVIATION MEANING IN LCD DISPLAY ................................................................................................. 16

3-7. LCD SETTING .................................................................................................................................... 17

3-8. OPERATING MODE/STATUS DESCRIPTION ................................................................................................. 23

3-9. FAULT CODE ...................................................................................................................................... 29

3-10.WARNING INDICATOR ......................................................................................................................... 29

3-11.WARNING CODE ................................................................................................................................ 30

4. TROUBLE SHOOTING ................................................................................................................... 30

5. STORAGE AND MAINTENANCE ..................................................................................................... 32

5-1. STORAGE .......................................................................................................................................... 32

5-2. MAINTENANCE .................................................................................................................................... 32

6. SPECIFICATIONS ......................................................................................................................... 33

1

EN

1. Safety and EMC instructions

Please read carefully the following user manual and the safety instructions before installing the unit or using

the unit!

1-1. Transportation and Storage

Please transport the UPS system only in the original package to protect against shock and

impact.

The UPS must be stored in the room where it is ventilated and dry.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm environment.

The UPS system must be absolutely dry before being installed. Please allow at least two hours for the

UPS system to acclimate the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or nearby heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS (e.g. big motor-type

equipment)) to the UPS output sockets or terminal.

Place cables in such a way that no one can step on or trip over them.

Do not block air vents in the housing of UPS. The UPS must be installed in a location with good

ventilation. Ensure enough space on each side for ventilation.

UPS has provided earthed terminal, in the final installed system configuration, equipotential

earth bonding to the external UPS battery cabinets.

The UPS can be installed only by qualified maintenance personnel.

An appropriate disconnect device as short-circuit backup protection should be provided in the

building wiring installation.

An integral single emergency switching device which prevents further supply to the load by the

UPS in any mode of operation should be provided in the building wiring installation.

Connect the earth before connecting to the building wiring terminal.

Installation and Wiring must be performed in accordance with the local electrical laws and

regulations.

2

EN

1-4. Operation

Do not disconnect the earth conductor cable on the UPS or the building wiring terminals in any

time since this would cancel the protective earth of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output sockets or

output terminal blocks may be electrically live even if the UPS system is not connected to the building

wiring outlet.

In order to fully disconnect the UPS system, first press the “OFF” button and then disconnect the

mains.

Ensure that no liquid or other foreign objects can enter into the UPS system.

The UPS can be operated by any individuals with no previous experience.

1-5. Standards

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission...............................:IEC/EN 62040-2 Category C3

Radiated Emission..................................:IEC/EN 62040-2 Category C3

*EMS

ESD.........................................................:IEC/EN 61000-4-2 Level 4

RS........................................................ ...:IEC/EN 61000-4-3 Level 3

EFT......................................................... :IEC/EN 61000-4-4 Level 4

SURGE................................................... :IEC/EN 61000-4-5 Level 4

CS........................................................... :IEC/EN 61000-4-6 Level 3

Power-frequency Magnetic field.............. :IEC/EN 61000-4-8 Level 4

Low Frequency Signals............................:IEC/EN 61000-2-2

Warning:

This is a product for commercial and industrial application in the

second environment-

installation restrictions or additional measures may be

needed to prevent disturbances.

3

EN

2. Installation and Operation

There are two different types of online UPS: standard and long-run models. Please refer to the following

model table.

Model

Type

Model

Type

10000

Standard

model

10000L

Long-run

model

15000

15000L

20000

20000L

30000

30000L

We also offer optional parallel function for these two types by request. The UPS with parallel function is

called as “Parallel model”. We have described detailed installation and operation of Parallel Model in the

following chapter.

2-1. Unpacking and Inspection

Unpack the package and check the package contents. The shipping package contains:

● One UPS

● One user manual

● One monitoring software CD

● One RS-232 cable (option)

● One USB cable

● One parallel cable (only available for parallel model)

● One share current cable (only available for parallel model)

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged

during transportation. Do not turn on the unit and notify the carrier and dealer immediately if there is any

damage or lacking of some parts. Please keep the original package in a safe place for future use.

4

EN

2-2. Rear Panel View

Diagram 1: 10000(L)/15000(L) Diagram 2: 30000L Rear Panel Diagram 3: 30000 Rear Panel

/20000 (L)

Rear Panel

Diagram 3: 10000(L)15000(L)/20000(L) Diagram 4: 30000(L)

Input/Output Terminal Input/Output Terminal

5

EN

1. RS-232 communication port

2. USB communication port

3. Emergency power off function connector (EPO connector)

4. Share current port (only available for parallel model)

5. Parallel port (only available for parallel model)

6. Intelligent slot

7. Power stage fan

8. External battery terminal

9. Bypass Input Circuit Breaker(Only available for dual input unit)

10. Input/Output terminal (Refer to Diagram 2)

11. Line Input circuit breaker

12. Maintenance bypass switch

13. Output Grounding terminal

14. Output terminal: connect to mission-critical loads

15. Line input terminal

16. Bypass input terminal(Only available for dual input)

17. Input Grounding terminal

2-3. Single UPS Installation

Installation and wiring must be performed in accordance with the local electric laws/regulations and execute

the following instructions by professional personnel.

1) Make sure the mains wire and breakers in the building are enough for the rated capacity of UPS to

avoid the hazards of electric shock or fire.

NOTE: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than

the UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed.

2) Switch off the mains switch in the building before installation.

3) Turn off all the connected devices before connecting to the UPS.

4) Prepare wires based on the following table:

Model

Wiring spec (AWG)

Input(Ph) Output(Ph) Neutral Battery Ground

10000 10 10 8 8

10000L 10 10 8 8 8

15000 8 8 6 6

15000L 8 8 6 6 6

20000 8 8 6 6

20000L 8 8 6 6 6

30000 8 8 4 4

30000L 8 8 4 4 4

6

EN

NOTE 1: The cable for 10000/10000L should be able to withstand over 40A current. It is

recommended to use AWG 10 or thicker wire for Phase and AWG 8 or thicker wire for Neutral for

safety and efficiency.

NOTE 2: The cable for 15000/15000L should be able to withstand over 63A current. It is

recommended to use AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety

and efficiency.

NOTE 3: The cable for 20000/20000L should be able to withstand over 63A current. It is

recommended to use AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety

and efficiency.

NOTE 4: The cable for 30000/30000L should be able to withstand over 63A current. It is

recommended to use AWG 8 or thicker wire for Phase and AWG 4 or thicker wire for Neutral for safety

and efficiency.

NOTE 5: The selections for color of wires should be followed by the local electrical laws and

regulations.

5) Remove the terminal block cover on the rear panel of UPS. Then connect the wires according to the

following terminal block diagrams: (Connect the earth wire first when making wire connection. Disconnect

the earth wire last when making wire disconnection!)

Terminal Block wiring diagram of 10000(L)/15000(L)/20000(L)

Terminal Block wiring diagram of 30000(L)

7

EN

For dual input unit, if there is two separate input, connect the Line input and bypass input respectively; if the

is only one common input, please connect the line input and bypass input together.

NOTE 1: Make sure that the wires are connected tightly with the terminals.

NOTE 2: Please install the output breaker between the output terminal and the load, and the breaker

should be qualified with leakage current protective function if necessary.

6) Put the terminal block cover back to the rear panel of the UPS.

Warning: (Only for standard model)

● Make sure the UPS is not turned on before installation. The UPS should not be turned on during wiring

connection.

● Do not try to modify the standard model to the long-run model. Particularly, do not try to connect the

standard internal battery to the external battery. The battery type and voltage may be different. If you

connect them together, it maybe causes the hazard of electric shock or fire!

Warning: (Only for long-run model)

● Make sure a DC breaker or other protection device between UPS and external battery pack is installed. If

not, please install it carefully. Switch off the battery breaker before installation.

NOTE: Set the battery pack breaker in “OFF” position and then install the battery pack.

● Pay highly attention to the rated battery voltage marked on the rear panel. If you want to change the

numbers of the battery pack, please make sure you modify the setting simultaneously. The connection

with wrong battery voltage may cause permanent damage of the UPS. Make sure the voltage of the

battery pack is correct.

● Pay highly attention to the polarity marking on external battery terminal block, and make sure the

correct battery polarity is connected. Wrong connection may cause permanent damage of the UPS.

● Make sure the protective earth ground wiring is correct. The wire current spec, color, position,

connection and conductance reliability should be checked carefully.

● Make sure the utility input & output wiring is correct. The wire current spec, color, position, connection

and conductance reliability should be checked carefully. Make sure the L/N site is correct, not reverse

and short-circuited.

8

EN

2-4. UPS Installation for Parallel System

If the UPS is only available for single operation, you may skip this section to the next.

1) Install and wires the UPSs according to the section 2-3.

2) Connect the output wires of each UPS to an output breaker.

3) Connect all output breakers to a major output breaker. Then this major output breaker will directly

connect to the loads.

4) Each UPS is connected to an independent battery pack.

NOTE: The parallel system can not use one battery pack. Otherwise, it will cause system permanent failure.

5) Refer to the following wiring diagram:

Wiring diagram of parallel system for 10000(L)/15000(L)/20000(L)

9

EN

Wiring diagram of parallel system for 30000(L)

2-5. Software Installation

For optimal computer system protection, install UPS monitoring software to fully configure UPS shutdown.

10

EN

3. Operations

3-1. Button Operation

Button Function

ON/Enter Button



Turn on the UPS: Press and hold the button more than 0.5s to turn on the UPS.

 Enter Key: Press this button to confirm the selection in setting menu.

OFF/ESC Button



Turn off the UPS: Press and hold the button more than 0.5s to turn off the UPS.

 Esc key: Press this button to return to last menu in setting menu.

Test/Up Button

 Battery test: Press and hold the button more than 0.5s to test the battery while

in AC mode and CVCF* mode.

 UP key: Press this button to display next selection in setting menu.

Mute/Down Button



Mute the alarm: Press and hold the button more than 0.5s to mute the buzzer.

Please refer to section 3-4-9 for details.

 Down key: Press this button to display previous selection in setting menu.

Test/Up +

Mute/Down Button



Press and hold the two buttons simultaneous more than 1s to enter/escape the

setting menu.

* CVCF means Constant Voltage and Constant Frequency.

3-2. LED Indicators and LCD Panel

LED Indicators:

There are 4 LEDs on front panel to show the UPS working status:

Mode LED Bypass Line Battery Fault

UPS On

●

No Output mode

○

Bypass mode

●

○

AC mode

○

●

○

Battery mode

○

●

○

CVCF mode

○

●

○

Battery Test

●

○

ECO mode

●

○

Fault

○

●

Note: ● means LED is lighting, and ○ means LED is faded.

LCD panel

LED indicators

11

EN

LCD Panel:

Display Function

Backup time information

Indicates the battery discharge time in numbers

H: hours, M: minutes, S: seconds

Fault information

Indicates that the warning and fault occurs.

Indicates the fault codes, and the codes are listed in details in section 3-9.

Mute operation

Indicates that the UPS alarm is disabled.

Output & Battery voltage information

Indicates the output voltage, frequency or battery voltage.

Vac: output voltage, Vdc: battery voltage, Hz: frequency

Load information

Indicates the load level by 0-25%, 26-50%, 51-75%, and 76-100%.

Indicates overload.

Indicates the load or the output is short.

Mode operation information

Indicates the UPS connects to the mains.

Indicates the battery is working.

Indicates the bypass circuit is working.

Indicates the ECO mode is enabled.

Indicates the Inverter circuit is working.

Indicates the output is working.

12

EN

Battery information

Indicates the Battery capacity by 0-25%, 26-50%, 51-75%, and 76-100%.

Indicates the battery is not connected.

Indicates low battery level and low battery voltage.

Input & Battery voltage information

Indicates the input voltage or frequency or battery voltage.

Vac: Input voltage, Vdc: battery voltage, Hz: input frequency

3-3. Audible Alarm

Description Buzzer status Muted

UPS status

Bypass mode Beeping once every 2 minutes

Yes

Battery mode Beeping once every 4 seconds

Fault mode Beeping continuously

Warning

Overload Beeping twice every second

No

Others Beeping once every second

Fault

All Beeping continuously

Yes

3-4. Single UPS Operation

1. Turn on the UPS with utility power supply (in AC mode)

1) After power supply is connected correctly, set the breaker of the battery pack at “ON” position (the

step only available for long-run model). Then set the line input breaker at “ON” position(for dual

input unit, also set the bypass input breaker at “ON”). At this time the fan is running and the UPS

enter to power on mode for initialization, several seconds later, UPS operates in Bypass mode and

supplies power to the loads via the bypass.

NOTE: When UPS is in Bypass mode, the output voltage will directly power from utility after you

switch on the input breaker. In Bypass mode, the load is not protected by UPS. To protect your

precious devices, you should turn on the UPS. Refer to next step.

2) Press and hold the “ON” button for 0.5s to turn on the UPS and the buzzer will beep once.

3) A few seconds later, the UPS will enter to AC mode. If the utility power is abnormal, the UPS will

operate in Battery mode without interruption.

NOTE: When the UPS is running out battery, it will shut down automatically at Battery mode. When the

utility power is restored, the UPS will auto restart in AC mode.

2. Turn on the UPS without utility power supply (in Battery mode)

1) Make sure that the breaker of the battery pack is at “ON” position (only for long-run model).

2) Press the “ON” button to set up the power supply for the UPS, UPS will enter to power on mode.

After initialization UPS will enter to No Output mode, then Press and hold the “ON” button for 0.5s

to turn on the UPS, and the buzzer will beep once.

3) A few seconds later, the UPS will be turned on and enter to Battery mode.

13

EN

3. Connect devices to UPS

After the UPS is turned on, you can connect devices to the UPS.

1) Turn on the UPS first and then switch on the devices one by one, the LCD panel will display total

load level.

2) If it is necessary to connect the inductive loads such as a printer, the in-rush current should be

calculated carefully to see if it meets the capacity of the UPS, because the power consumption of

this kind of loads is too big.

3) If the UPS is overload, the buzzer will beep twice every second.

4) When the UPS is overload, please remove some loads immediately. It is recommended to have the

total loads connected to the UPS less than 80% of its nominal power capacity to prevent overload

for system safety.

5) If the overload time is over acceptable time listed in spec at AC mode, the UPS will automatically

transfer to Bypass mode. After the overload is removed, it will return to AC mode. If the overload

time is over acceptable time listed in spec at Battery mode, the UPS will become fault status. At this

time, if bypass is enabled, the UPS will power to the load via bypass. If bypass function is disabled

or the input power is not within bypass acceptable range, it will cut off output directly.

4. Charge the batteries

1) After the UPS is connected to the utility power, the charger will charge the batteries automatically

except in Battery mode or during battery self-test.

2) Suggest to charge batteries at least 10 hours before use. Otherwise, the backup time may be

shorter than expected time.

3) Make sure the battery numbers setting on the control board (Please refer to the section 3-4-12 for

detailed setting) is consistent to real connection.

5. Battery mode operation

1) When the UPS is in Battery mode, the buzzer will beep according to different battery capacity. If the

battery capacity is more than 25%, the buzzer will beep once every 4 seconds; If the battery

voltage drops to the alarm level, the buzzer will beep quickly (once every sec) to remind users that

the battery is at low level and the UPS will shut down automatically soon. Users could switch off

some non-critical loads to disable the shutdown alarm and prolong the backup time. If there is no

more load to be switched off at that time, you have to shut down all loads as soon as possible to

protect the devices or save data. Otherwise, there is a risk of data loss or load failure.

2) In Battery mode, if buzzer sound annoys, users can press the Mute button to disable the buzzer.

3) The backup time of the long-run model depends on the external battery capacity.

4) The backup time may vary from different environment temperature and load type.

5) When setting backup time for 16.5 hours (default value from LCD panel), after discharging 16.5

hours, UPS will shut down automatically to protect the battery. This battery discharge protection

can be enabled or disabled through LCD panel control. (Refer to 3-7 LCD setting section)

6. Test the batteries

1) If you need to check the battery status when the UPS is running in AC mode/CVCF mode, you could

press the “Test” button to let the UPS do battery self-test.

2) Users also can set battery self-test through monitoring software.

7. Turn off the UPS with utility power supply in AC mode

1) Turn off the inverter of the UPS by pressing “OFF” button for at least 0.5s, and then the buzzer will

beep once. The UPS will turn into Bypass mode.

NOTE 1: If the UPS has been set to enable the bypass output, it will bypass voltage from utility

power to output terminal even though you have turned off the UPS (inverter).

14

EN

NOTE 2: After turning off the UPS, please be aware that the UPS is working at Bypass mode and

there is risk of power loss for connected devices.

2) In Bypass mode, output voltage of the UPS is still present. In order to cut off the output, switch off

the line input breaker(for dual input unit, also switch off the bypass line breaker). A few seconds

later, there is no display shown on the display panel and UPS is complete off.

8. Turn off the UPS without utility power supply in Battery mode

1) Turn off the UPS by pressing “OFF” button for at least 0.5s, and then the buzzer will beep once.

2) Then UPS will cut off power to output and there is no display shown on the display panel.

9. Mute the buzzer

1) To mute the buzzer, please press the “Mute” button for at least 0.5s. If you press it again after the

buzzer is muted, the buzzer will beep again.

2) Some warning alarms can’t be muted unless the error is fixed. Please refer to section 3-3 for the

details.

10. Operation in warning status

1) When Fault LED flashes and the buzzer beeps once every second, it means that there are some

problems for UPS operation. Users can get the warning indicator from LCD panel. Please check the

trouble shooting table in chapter 4 for details.

2) Some warning alarms can’t be muted unless the error is fixed. Please refer to section 3-3 for the

details.

11. Operation in Fault mode

1) When Fault LED illuminates and the buzzer beeps continuously, it means that there is a fatal error in

the UPS. Users can get the fault code from display panel. Please check the trouble shooting table

in chapter 4 for details.

2) Please check the loads, wiring, ventilation, utility, battery and so on after the fault occurs. Don’t try

to turn on the UPS again before solving the problems. If the problems can’t be fixed, please contact

the distributor or service people immediately.

3) For emergency case, please cut off the connection from utility, external battery, and output

immediately to avoid more risk or danger.

12. Operation of changing battery numbers

1) This operation is only available for professional or qualified technicians.

2) Turn off the UPS. If the load couldn’t be cut off, you should remove the cover of maintenance

bypass switch on the rear panel and turn the maintenance switch to “BPS” position first.

3) Switch off the line input breaker(for dual input unit, also switch off the bypass input breaker), and

switch off the battery breaker (only available for long-run model).

4) Remove the cabinet cover, and disconnect battery wire for standard model. Then modify the

jumper of JS3 on the control board to set the battery numbers as following table.

Note:1 = connect with jumper; 0 = no jumper; x = the pins are for other functions.

5) Modify the battery pack for the setting number carefully. After complete it, put the cover back,

switch on the battery breaker for long-run model.

Battery Number

in series

JS3

pin1 & pin2 pin3 & pin4 Pin5 & pin6 pin7 & pin8

18 1 0 0 X

19 0 1 0 X

20 0 0 1 X

15

EN

6) Switch on the line input breaker(for dual input unit, also switch on the bypass input breaker) and

the UPS will enter Bypass mode. If the UPS is in maintenance Bypass mode, turn the maintenance

switch to “UPS” position and then turn on the UPS.

3-5. Parallel Operation

1. Parallel system initial startup

First of all, please make sure all of the UPSs are parallel models and have the same configuration.

1) Turn on each UPS to AC mode respectively (Refer to section 3-4(1)). Then, measure the inverter

output voltage of each phase for each UPS to check if the inverter voltage difference between

actual output and setting value is less than 1.5V (typical 1V) with multimeter. If the difference is

more than 1.5V, please calibrate the voltage by configuring inverter voltage adjustment (Refer to

Program 15, 16 and 17, section 3-7) in LCD setting. If voltage difference remains more than 1.5V

after calibration, please contact your local distributor or service center for help.

2) Calibrate the output voltage measurement by configuring output voltage calibration (Refer to

Program 18, 19, and 20, section 3-7) in LCD setting to make sure the difference between real

output voltage and detected value of UPS is less than 1V.

3) Turn off each UPS (Refer to section 3-4(7.)). Then, follow the wiring procedure in section 2-4.

4) Remove the cover of parallel share current cable port on the UPS, connect each UPS one by one

with the parallel cable and share current cable, and then screw the cover back.

5) Turn on the parallel system in AC mode:

a) Turn on the line input breaker of each UPS(for dual input, also turn on bypass input breaker).

After all UPSs enter to bypass mode, measure the output voltage between two UPS for the

same phase to make sure the phase sequence is correct . If these two voltage differences are

near to zero, that means all connections are correct. Otherwise, please check if the wirings are

connected correctly.

b) Turn on the output breaker of each UPS.

c) Turn on each UPS in turns. After a while, the UPSs will enter to AC mode synchronously and

then, the parallel system is completed.

6) Turn on the parallel system in Battery mode:

a) Turn on the battery breaker (only available in long-run model) and output breaker of each UPS.

NOTE: It’s not allowed to share one battery pack for long-run UPSs in parallel system. Each UPS

should be connected to its battery pack.

b) Turn on any UPS. A few seconds later, the UPS will enter to battery mode.

c) Then, turn on another UPS. A few seconds later, the UPS will enter to battery mode and add to the

parallel system.

d) If you have the third UPS, follow the same procedure of c). Then, the parallel system is complete.

If more detailed information is needed, please contact supplier or service center for parallel

operation instruction.

2. Add one new unit into the parallel system

1) You can not add one new unit into the parallel system when whole system is running. You must cut

off the load and shutdown the system.

2) Make sure all of the UPS are the parallel models, and follow the wiring refer to section 2-4.

3) Install the new parallel system refers to the previous section.

3. Remove one unit from the parallel system

There are two methods to remove one unit from the parallel system:

First method:

16

EN

1) Press the “OFF” key twice and each time should be lasted for more than 0.5s. Then, the UPS will

enter into bypass mode or no output mode without output.

2) Turn off the output breaker of this unit, and then turn off the input breaker of this unit.

3) After it shuts down, you can turn off the battery breaker (for long-run model) and remove the

parallel and share current cables. And then remove the unit from the parallel system.

Second method:

1) If the bypass is abnormal, you can not remove the UPS without interruption. You must cut off the

load and shut down the system first.

2) Make sure the bypass setting is enabled in each UPS and then turn off the running system. All UPSs

will transfer to Bypass mode. Remove all the maintenance bypass covers and set the maintenance

switches from “UPS” to “BPS”. Turn off all the input breakers and battery breakers in parallel system.

3) Turn off the output breaker and remove the parallel cable and share current cable of the UPS which

you want to remove. Then, remove it from parallel system.

4) Turn on the input breaker of the remaining UPS and the system will transfer to Bypass mode. Set

the maintenance switches from “BPS” to “UPS and put the maintenance bypass covers back.

5) Turn on the remaining UPS according to the previous section.

Warning: (Only for the parallel system)

● Before turning on the parallel system to activate inverter, make sure that all unit’s maintenance switch

at the same position.

● When parallel system is turned on to work through inverter, please do not operate the maintenance

switch of any unit.

3-6. Abbreviation Meaning in LCD Display

Abbreviation Display content Meaning

ENA

Enable

DIS

Disable

ATO

Auto

BAT

Battery

NCF

Normal mode (not CVCF mode)

CF

CVCF mode

SUB

Subtract

ADD

Add

ON

On

OFF

Off

FBD

Not allowed

OPN

Allow

RES

Reserved

N.L

Neutral line loss

CHE

Check

17

EN

OP.V

Output voltage

PAR

Parallel, 001 means the first UPS

AN

The first phase

BN

The second phase

CN

The third phase

AB

The first line

BC

The second line

CA

The third line

3-7. LCD Setting

There are three parameters to set up the UPS. Refer to following diagram.

Parameter 1: It’s for program alternatives. Refer

to below tables for the programs to set up.

Parameter 2 and parameter 3 are the setting

options or values for each program.

Note: Please select “Up” or “Down” button to

change the programs or parameters.

Programs available list for parameter 1:

Code Description

Bypass /

No Output mode

AC

mode

ECO

mode

CVCF

mode

Battery

mode

Battery

Test

01 Output voltage Y*

02 Output frequency Y

03 Voltage range for bypass Y

04 Frequency range for bypass Y

05 ECO mode enable/disable Y

06 Voltage range for ECO mode Y

07 Frequency range for ECO mode Y

08 Bypass mode setting Y Y

09

Maximum battery discharge time

setting

Y Y Y Y Y Y

10 Reserved Reserved for future options

11 Reserved Reserved for future options

12 Neutral loss detection Y Y Y Y Y Y

Parameter 1

Parameter 2

Parameter 3

Strona jest ładowana ...

Power Walker VFI 20000CP 3/3L Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Power Walker VFI 20000CP 3/3L Instrukcja obsługi

w innych językach

Inne dokumenty