Vertex 2KW Instrukcja obsługi

3KW Off-Grid PV Inverter

User Manual

www.neoenerji.com

Table Of Contents

1. Introduction ...................................................................................................... 1

2. Important Safety Warning ............................................................................... 2

3. Unpacking & Overview ..................................................................................... 4

3-1. Packing List .................................................................................................. 4

3-2. Product Overview .......................................................................................... 4

4. Installation........................................................................................................ 5

4-1. Selecting Mounting Location .......................................................................... 5

4-2. Mounting Unit ............................................................................................... 5

5. AC Input Connection ............................................................................................ 7

5-1. Preparation .................................................................................................. 7

5-2. Connecting to the AC Power Source ................................................................ 7

6. PV Module (DC) Connection ............................................................................. 8

7. Battery Connection ........................................................................................... 9

8. Load (AC Output) Connection......................................................................... 10

9. Commissioning ................................................................................................ 11

10. Operation ........................................................................................................ 12

10-1. Interface ................................................................................................... 12

10-2. LCD Information Define .............................................................................. 12

10-3. Button Definition ........................................................................................ 14

10-4 Query Menu Operation ................................................................................ 14

11. Charging Management ................................................................................... 23

12. Maintenance & Cleaning .................................................................................. 25

13. Trouble Shooting .............................................................................................. 26

13-1. Warning List .............................................................................................. 26

13-2. Fault Reference Codes ................................................................................ 27

14. Specifications ................................................................................................... 31

www.neoenerji.com

1

1. Introduction

This off-grid PV inverter can provide power to connected loads by utilizing PV power, AC power

and battery power. When PV energy is sufficient, it will power connected loads and charge

battery. When PV energy is not sufficient, this inverter will power connected loads and charge

battery from AC power source. When both PV energy and AC power source are not available,

it will provide battery power to connected loads.

Figure 1 Basic Off-Grid PV System Overview

Depending on different power situations, this hybrid inverter is designed to generate

continuous power from PV solar modules (solar panels), battery, and the utility. When MPP

input voltage of PV modules is within 150 VDC to 500 VDC, this inverter is able to generate

power to the load and charge battery. This inverter is only compatible with PV module types of

single crystalline and poly crystalline. Do not connect any PV array types other than these two

types of PV modules to the inverter. See Figure 1 for a simple diagram of a typical solar system

with this hybrid inverter.

Note: When PV input voltage is lower than 250V, the power of inverter will de-rate.

PV module

Battery

Off-Grid inverter

AC power source

Load

www.neoenerji.com

2

Conventions used:

WARNING! Warnings identify conditions or practices that could result in personal injury;

CAUTION! Caution identify conditions or practices that could result in damaged to the

unit or other equipment connected.

2. Important Safety Warning

Before using the inverter, please read all instructions and cautionary markings on

the unit and this manual. Store the manual where it can be accessed easily.

This manual is for qualified personnel. The tasks described in this manual may be performed

by qualified personnel only.

General Precaution-

WARNING! Before installing and using this inverter, read all instructions and cautionary

markings on the inverter and all appropriate sections of this guide.

WARNING! Normally grounded conductors may be ungrounded and energized when a

ground fault is indicated.

WARNING! This inverter is heavy. It should be lifted by at least two persons.

CAUTION! Authorized service personnel should reduce the risk of electrical shock by

disconnecting AC, DC and battery power from the inverter before attempting any maintenance

or cleaning or working on any circuits connected to the inverter. Turning off controls will not

reduce this risk. Internal capacitors can remain charged for 5 minutes after disconnecting all

sources of power.

CAUTION! Do not disassemble this inverter yourself. It contains no user-serviceable parts.

Attempt to service this inverter yourself may cause a risk of electrical shock or fire and will

void the warranty from the manufacturer.

CAUTION! To avoid a risk of fire and electric shock, make sure that existing wiring is in good

condition and that the wire is not undersized. Do not operate the Inverter with damaged or

substandard wiring.

CAUTION! Under high temperature environment, the cover of this inverter could be hot

enough to cause skin burns if accidentally touched. Ensure that this inverter is away from

normal traffic areas.

www.neoenerji.com

3

CAUTION! Use only recommended accessories from installer . Otherwise, not-qualified tools

may cause a risk of fire, electric shock, or injury to persons.

CAUTION! To reduce risk of fire hazard, do not cover or obstruct the heat sink.

CAUTION! Do not operate the Inverter if it has received a sharp blow, been dropped, or

otherwise damaged in any way. If the Inverter is damaged, called for an RMA (Return Material

Authorization).

www.neoenerji.com

4

3. Unpacking & Overview

3-1. Packing List

Before installation, please inspect the unit. Be sure that nothing inside the package is

damaged. You should have received the following items inside of package:

Inverter unit Software CD Manual USB cable

3-2. Product Overview

1) PV connectors

2) Grid connectors (AC input connection)

3) Battery connectors

4) AC output connectors (Load connection)

5) RS-232 communication port

6) USB communication port

7) Intelligent slot

8) LCD display panel (Please check section 10 for detailed LCD operation)

9) Operation buttons

www.neoenerji.com

5

WARNING!! Remember that this inverter is heavy! Please be carefully when lifting out

from the package.

4. Installation

4-1. Selecting Mounting Location

Consider the following points before selecting where to install:

 Do not mount the inverter on flammable construction materials.

 Mount on a solid surface

 This inverter can make noises during operation which may be perceived as a nuisance in

a living area.

 Install this inverter at eye level in order to allow the LCD display to be read at all times.

 For proper air circulation to dissipate heat, allow a clearance of approx. 20 cm to the

side and approx. 50 cm above and below the unit.

 Dusty conditions on the unit may impair the performance of this inverter.

 The ambient temperature should be between 0°C and 40°C to ensure optimal operation.

 The recommended installation position is to be adhered to (vertical).

 For proper operation of this inverter, please use appropriate cables for grid connection.

 Select an appropriate mounting location. Install the solar inverter in a protected area

that is free of excessive dust and has adequate air flow. Do NOT operate it where the

temperature and humidity is beyond the specific limits. (Please check the specs for the

limitations.)

 This inverter is designed with IP20 for indoor applications only.

4-2. Mounting Unit

Installation to the wall should be implemented with the proper screws. Mount the wall bracket

so that the solar inverter can be easily attached to the wall. After that, the device should be

bolted on securely.

www.neoenerji.com

6

1. Drill four holes in the marked locations

with four screws.

2. Place the unit on the surface and align the

mounting holes with the four screws.

3. Check if the solar inverter is firmly

secured.

Note: Recommended specs for screws.

www.neoenerji.com

7

Chart 2

5. AC Input Connection

5-1. Preparation

Before connecting to AC input power source, please install a separate AC circuit breaker

between inverter and AC power source. This will ensure the inverter can be securely

disconnected during maintenance and fully protected from over current of AC input.

NOTE1: Although this inverter is equipped with a fuse (F6 point on PCB, 250VAC/30A), it’s

still necessary to install a separate circuit breaker for safety consideration. Please use

250VAC/30A circuit breaker.

WARNING! It's very important for system safety and efficient operation to use appropriate

cable for AC connection. To reduce risk of injury, please use the proper recommended cable

size as below.

Suggested cable requirement for AC wire

Conductor cross-section (mm

2

)

AWG no.

≥3.35

10 - 12

5-2. Connecting to the AC Power Source

Step 1: Check the AC voltage and frequency with an AC voltmeter. It should be the same to

“VAC” value on the product label.

Step 2: Turn off the circuit breaker.

Step 3: Remove insulation sleeve 8 mm for three

conductors. And shorten phase L and neutral conductor

N 3 mm. Refer to chart 1.

Step 4: Connect wires according to polarities indicated on terminal block. Be sure to connect

PE protective conductor ( ) first.

L→LINE (brown or black)

→Ground (yellow-green)

N→Neutral (blue)

Step 5: Make sure the wires are securely

connected.

CAUTION: To prevent risk of electric shock, ensure the ground wire is properly earthed

before operating this inverter no matter the AC input is connected or not.

Chart 1

www.neoenerji.com

8

6. PV Module (DC) Connection

CAUTION: Before connecting to PV modules, please install separately a DC circuit breaker

between inverter and PV modules.

NOTE: Please use 600VDC/25A circuit breaker.

Please follow below steps to implement PV module connection:

Step 1: Check the input voltage of PV array modules. The acceptable input voltage of the solar

inverter is 250VDC - 450VDC. This system is only applied with one string of PV array. Please

make sure that the maximum current load of PV input connector is 13A.

Step 2: Disconnect the circuit breaker.

Step 3: Remove insulation sleeve 10 mm for positive and

negative conductors. Refer to chart 3.

Step 4: Check correct polarity of connection cable from

PV modules and PV input connectors. Then, connect

positive pole (+) of connection cable to positive pole (+)

of PV input connector. Connect negative pole (-) of

connection cable to negative pole (-) of PV input

connector. Refer to Chart 4.

Step 5: Make sure the wires are securely connected.

CAUTION: Exceeding the maximum input voltage can destroy the unit!! Check the system

before wire connection.

WARNING: This inverter is only compatible to two types of PV modules: single crystalline

and poly crystalline. To avoid any malfunction, do not connect any PV modules with

possibility of leakage current to the inverter.

Chart 4

Chart 3

www.neoenerji.com

9

WARNING! It's very important for system safety and efficient operation to use appropriate

cable for PV module connection. To reduce risk of injury, please use the proper recommended

cable size as below.

Conductor cross-section (mm

2

)

AWG no.

≥3.35

6 - 12

7. Battery Connection

CAUTION: Before connecting to batteries, please install separately a DC circuit breaker

between inverter and batteries.

NOTE: Please only use sealed lead acid battery, Lithium iron, vented, Nicd, and Gel battery.

Please check maximum charging voltage and current when first using this inverter.

NOTE: Please use 60VDC/100A circuit breaker.

Please follow below steps to implement battery connection:

Step 1: Check the nominal voltage of batteries. The nominal input voltage for this inverter is

48VDC.

Step 2: Use two battery cables. Remove insulation sleeve 12

mm and insert conductor into cable ring terminal. Refer to

chart 5.

Step 3: Following battery polarity guide printed near the

battery terminal! Place the external battery cable ring terminal

over the battery terminal. Refer to Chart 6.

RED cable to the positive terminal (+);

BLACK cable to the negative terminal (-).

Step 4: Make sure the wires are securely connected

WARNING! It's very important for system safety and

efficient operation to use appropriate cable for battery

connection. To reduce risk of injury, please use the proper

recommended cable size as below.

Conductor cross-section (mm

2

)

AWG no.

≥13.3

≤6

CAUTION: If it’s necessary to turn off the inverter during operation, make sure to

disconnect the AC breaker first and then PV DC breaker.

CAUTION: Never directly touch terminals of the inverter. It will cause lethal electric shock.

Chart 5

Chart 6

www.neoenerji.com

10

Chart 8

8. Load (AC Output) Connection

WARNING! It's very important for system safety and efficient operation to use appropriate

cable for AC connection. To reduce risk of injury, please use the proper recommended cable

size as below.

Conductor cross-section (mm2)

AWG no.

≥3.35

10 - 12

Step 1: Remove insulation sleeve 8 mm for three

conductors. And shorten phase L and neutral conductor N 3

mm. Refer to chart 7.

Step 2: Connect wires according to polarities indicated on

terminal block. Be sure to connect PE protective conductor

( ) first. Refer to Chart 8.

L→LINE (brown or black)

→Ground (yellow-green)

N→Neutral (blue)

Step 3: Make sure the wires are securely connected.

CAUTION: It’s only allowed to connect load to “AC Output Connector”. Do NOT connect

the utility to AC Output Connector.

CAUTION: This inverter is not allowed to operate in parallel. Please do NOT parallel

connect more than one unit in AC output connector. Otherwise, it will damage this inverter.

Chart 7

www.neoenerji.com

11

9. Commissioning

Step 1: Check the following requirements before commissioning:

 Ensure the inverter is firmly secured

 Check if the open circuit DC voltage of PV module meets requirement (Refer to Section

6)

 Check if connection of AC cable to AC power source is correct.

 Full connection to PV modules.

 AC circuit breaker, batter circuit breaker, and DC circuit breaker are installed correctly.

Step 2: Switch on the battery circuit breaker and then switch on PV DC breaker. After that, if

there is utility connection, please switch on the AC circuit breaker. At this moment, the inverter

is turned on already. However, there is no output generation for loads. Then:

 If LCD lights up to display the current inverter status, commissioning has been

successfully. After pressing “ON” button for 1 second when the utility is detected, this

inverter will start to supply power to the loads. If no utility exists, simply press “ON”

button for 3 seconds. Then, this inverter will start to supply power to the loads.

 If red LED lights up, or warning/fault indicator appears in LCD, an error has occurred to

this inverter. Please inform your installer.

Step 3: Install monitoring software in your PC. Follow below steps to install software.

1. Go to the website http://www.power-software-download.com/solarpower.html

to download software in your PC. Then, please execute setup.exe for initiating installation

software.

2. Follow the on-screen instructions to install the software.

3. When your computer restarts, the monitoring software will appear as shortcut icon located

in the system tray, near the clock.

www.neoenerji.com

12

10. Operation

10-1. Interface

This display is operated by four buttons.

NOTICE: To accurately monitor and calculate the energy generation, please calibrate the

timer of this unit via software every one month. For the detailed calibration, please check the

user manual of bundled software.

10-2. LCD Information Define

Display

Function

Indicates AC input voltage or frequency.

Vac: voltage, Hz: frequency

Indicates AC output power, voltage, frequency, or load

percentage.

KW: power, Vac: Voltage, Hz: frequency, %: Load

percentage

www.neoenerji.com

13

Indicates PV input voltage or power.

Volt: voltage, KW: power

Indicates battery voltage or percentage.

Volt: voltage, %: percentage

Indicates charging current to battery.

Indicates that the warning occurs.

Indicates that the fault occurs.

Indicates fault code or warning code.

Indicates date and time, or the date and time users set for

querying energy generation.

Indicates solar panels.

Icon flashing indicates PV input voltage or is out of range.

Indicates utility.

Icon flashing indicates utility voltage or frequency is out of

range.

Indicates battery condition. And the lattice of the icon

indicates battery capacity.

Icon flashing indicates battery is not connected.

Icon flashing indicates the battery voltage is too low.

Indicates AC output for loads is enabled and inverter is

providing power to the connected loads.

Indicates AC output for loads is enabled but there is no

power provided from inverter. At this time, no battery and

the utility are available. Only PV power exists but is not able

to provide power to the connected loads.

Indicates overload.

Indicates PV energy generated.

www.neoenerji.com

14

10-3. Button Definition

Button

Operation

Function

ENTER/ON

Short press.

Enter query menu.

If it’s in query menu, press this button to

confirm selection or entry.

Press and hold the button for

approximately 1 second when

the utility is detected or 3

seconds without the utility.

This inverter is able to provide power to

connected loads via AC output connector.

ESC/OFF

Short press.

Return to previous menu.

Press and hold the button

until the buzzer continuously

sounds.

Turn off power to the loads.

Up

Short press.

Select last selection or increase value.

Down

Short press.

If it’s in query menu, press this button to

jump to next selection or decrease value.

Mute alarm in standby mode or battery

mode.

NOTE: If backlight shuts off, you may activate it by pressing any button. When an error

occurs, the buzzer will continuously sound. You may press any button to mute it.

10-4 Query Menu Operation

The display shows current contents that have been set. The displayed contents can be

changed in query menu via button operation. Press ‘Enter’ button to enter query menu. There

are seven query selections:

 Input voltage or frequency of AC input

 Frequency, voltage, power or load percentage of AC output

 Input voltage or power of PV input.

 Battery voltage or capability percentage.

 Date and time.

 Today or total energy generated.

 Mode of query energy generated.

www.neoenerji.com

15

Setting Display Procedure

 Input voltage or frequency of AC input

Procedure

1.

Enter

Up

Down

Up

Down

EnterEnter

2.

3.

4.

5.

 Frequency, voltage, power or percentage of AC output

Procedure

1.

Enter

Up

Down

Up

Down

EnterEnter

2.

3.

4.

5.

www.neoenerji.com

16

Input voltage or power of PV input.

Procedure

1.

Enter

Up

Down

Up

Down

EnterEnter

2.

3.

4.

5.

 Battery voltage or percentage.

Procedure

1.

Enter

Up

Down

Up

Down

EnterEnter

2.

3.

4.

5.

www.neoenerji.com

17

 Date and time.

Procedure

1.

Enter

Up

Down

Up

Down

Enter

2.

3.

4.

5.

 Today or total energy generated.

Procedure

Enter

Up

Down

Up

Down

Enter

3.

4.

www.neoenerji.com

18

 Mode of query energy generated.

Energy generation display of selected day

Procedure

1.

Enter

Up

Down

Up

Down

Enter

2.

3.

4.

5.

Enter

Flashes

Enter

Up Down

Enter

Esc

Up

Down

Returns to main menu

6.

Sets year

Sets month

Sets day

LCD Display:

Energy generation display of selected month

Procedure

1.

Enter

Up

Down

Up

Down

Enter

2.

3.

4.

5.

Enter

Flashes

Enter

Up Down

Enter

Esc

Up

Down

Returns to main menu

6.

Sets year

Sets month

LCD Display:

www.neoenerji.com

Strona jest ładowana ...

Vertex 2KW Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Vertex 2KW Instrukcja obsługi

w innych językach

Inne dokumenty