Novus NVIP-5VE-6711/TA/3 Instrukcja obsługi

NVIP-5VE-6711/TA/3

Quick start guide

2

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Exclusion of liability in the event of damage to data contained on disks or other devices or media:

The manufacturer is not liable in the event of damage or loss of data contained on disks or other

devices or carriers during the operation of the Product.

Obligation to consult the Manufacturer before performing any action not provided for in the

instruction manual or other documents:

Before performing an action that is not provided for a given Product in the user manual, other

documents attached to the Product or does not result from the normal purpose of the Product, it is

necessary, under pain of exclusion of the Manufacturer's liability for the consequences of such action,

to contact the Manufacturer.

Pictures in this publication showing camera views can be simulations. Actual camera

images may vary depending on the type, model, settings, observation area, or

environmental conditions.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonization of the laws of the Member States

relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes).

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electronic equipment WEEE)

(OJ L 197, 24.7.2012, p. 38–71, with changes).

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in

electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes).

COMMISION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending

Annex II to Directive 2011/65/EU of the European Parliament and of the Council as regards

the list of restricted substances.

DIRECTIVE (EU) 2017/2102 OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 15 November 2017 amending Directive 2011/65/EU on the restriction of the

use of certain hazardous substances in electrical and electronic equipment.

3

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

3

IMPORTANT SAFEGUARDS AND WARNINGS

1. Please read this manual carefully before installation and operation;

2. Please keep this manual for the lifespan of the device in case referring to the contents of this

manual is necessary;

3. It is necessary to comply with the safety requirements described in the manual, as they have a

direct impact on the safety of users and the durability and reliability of the device;

4. All activities performed by installers and users must be carried out as described in the manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. It is not allowed to use any additional devices, components or accessories not provided for and not

recommended by the manufacturer;

7. Do not install this device in places where proper ventilation cannot be provided (e.g. closed

cabinets, etc.), as this may cause heat build-up and may result in damage;

8. Do not place the device on unstable surfaces. Installation must be carried out by qualified

personnel with appropriate permissions in accordance with the recommendations provided in this

manual;

9. The device may be powered only from sources with parameters compliant with those indicated by

the manufacturer in the technical data;

Before using the device, read the instruction manual in order to ensure proper and safe operation

of the device. Failure to comply with the instructions may lead to damage to the device and/or

safety violations.

The user may not repair the device himself. Repairs and maintenance of the device may only be

performed by qualified service personnel.

The device, which is an element of a professional CCTV system used for supervision and

control, is not intended for self-assembly in households by persons without specialist

knowledge.

As the product is constantly improved and optimised, some of its parameters and functions may have

changed from those described in this manual. If in doubt, please refer to the user manual at

www.novuscctv.com

The user manual located at www.novuscctv.com is always the most up-to-date version.

4

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

4

TABLE OF CONTENTS .................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimensions .......................................................................................... ...7

1.4. Package contents .............................................................................................. ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors and control tools ........................................................ 8

2.2. Ethernet cable connecting .................................................................................. 9

2.2. Power connection ................................................................................................ 9

2.3. Camera mounting .............................................................................................. 10

2.4. Starting the IP camera ....................................................................................... 11

2.5. Initial configuration via the web browser .......................................................... 12

2.6. Security recommendations for network architecture and configuration ......... 13

3. NETWORK CONNECTION USING WEB BROSWER ......................................... 14

3.1. Recommended PC specification for web browser ............................................. 14

3.2. Connection with IP camera via web browser ..................................................... 14

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 19

4.1. Displaying live video. ........................................................................................ 19

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 20

5.1. MicroSD card installation ................................................................................. 20

6. FACTORY SETTINGS RESTORING ...................................................................... 21

6.1. Software factory settings restoring via web browser ......................................... 21

6.2. Software factory settings restoring via NMS IPTool……… ... ………………..21

6.3. Hardware factory settings restoring ...................... ………………..…………...22

TABLE OF CONTENTS

5

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

5

1. FOREWORD INFORMATION

1.1. General Characteristics

General:

• Dual camera - thermal/visual

• FPA - thermal image sensor that allows observation of objects in total darkness

• Thermo dual vision - a feature that allows to overlay a thermal image on a video image

• Advanced image analysis features based on Deep Learning available in both thermal and video

modules

• Ability to use two different image analysis functions at the same time

• Temperature measurement at any point or area

• Temperature alarm - alarming if the temperature threshold is exceeded at any point or area

• Fire detection - alarming about the appearance of fire in the field of view of the camera

• 10 Temperature measurement zones (polygon, line, point)

• Active deterrence: LED warning lamp, white flashing or continuous light

• Audio speaker built into the camera with the ability to use custom voice messages

Thermal module:

• FPA - uncooled microbolometer

• Number of effective pixels: 256 x 192

• Fixed-focal lens: f=3.2 mm/F1.1

• Object detection range: 133m - human, 409m - vehicle

• Object recognition range: 33m - human, 102m - vehicle

• Detection temperature: -20°C ~ 150 °C

• Temperature Measurement Accuracy ± 2°C

• Video content analysis: line cross, intrusion detection

Video module:

• 5 MPX CMOS sensor 1/2.7” OmniVision

• Fixed-focal lens: f=4 mm/F1.6

• Stream resolution up to: 2592 x 1944

• Compression: H.264, H.265, MJPEG / G.711

• Video content analysis: tamper, line cross, zone entrance, zone exit, cross counting, scene

change, video blurred, video color cast, intrusion detection

Others:

• MicroSD card support up to 256 GB

• Onvif protocol support

• Ability to define compression, resolution, speed and quality for each stream

• Power supply 12 VDC/PoE

FOREWORD INFORMATION

6

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

6

1.2. Technical specification

FOREWORD INFORMATION

IMAGE - THERMAL MODULE

Image Sensor Uncooled FPA Microbolometer

Number of Effective Pixels 256 (H) x 192 (V)

Pixel Size 12 µm

Spectral Range 8 - 14 µm

Thermal Sensitivity 50 mK

Thermovision Modes White Hot, Black Hot, Rainbow, Iron Oxide Red, Lava Color

Detection Temperature -20°C ~ 150°C

LENS - THERMAL MODULE

Lens Type f=3.2 mm/F1.1

Object Detection Range 133m - human , 409m - vehicle

Object Recognition Range 33m - human , 102m - vehicle

IMAGE

Image Sensor 5 MPX CMOS sensor 1/2.7” OmniVision

Number of Effective Pixels 2688 (H) x 1944 (V)

Min. Illumination 0.02 lx/F1.6 - color mode, 0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1/3 s ~ 1/100000 s

Digital Slow Shutter (DSS) up to 1/3 s

Digital Noise Reduction (DNR) 2D, 3D

Defog Function (F-DNR) yes

Highlight Compensation (HLC) yes

Back Light Compensation (BLC) yes

Reduction of image flicker (Antiflicker) yes

LENS

Lens Type fixed focal, f=4 mm/F1.6

DAY/NIGHT

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time, external

Switching Level Adjustment yes

Switching Delay 2 ~ 120 s

Switching Schedule yes

Visible Light Sensor yes

NETWORK

Stream Resolution 2592 x 1944, 2592 x 1520, 2560 x 1440 (QHD), 2304 x 1296, 1920 x 1080 (Full HD),

1280 x 720 (HD), 704 x 576, 480 x 240, 352 x 288 (CIF)

for thermal module: 704x576, 352 x 288 (CIF), 1280x720, 480x240

Frame Rate 30 fps for each resolution

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous Connections max. 10

Bandwidth 50 Mb/s in total

Network Protocols Support HTTP, IPv4, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS, NTP, RTSP, RTP, UPnP, SNMP, QoS,

IEEE 802.1X, PPPoE, SMTP, RTCP, ICMP

ONVIF Protocol Support Profile S/G/T

Camera Configuration from Internet Explorer, Firefox, Chrome, Opera, Edge browser

languages: Polish, English, and others

Compatible Software NMS, NOVUS MANAGEMENT SYSTEM AC, N Control 6000

Mobile applications SuperLive Plus (iPhone, Android)

7

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

7

FOREWORD INFORMATION

1.3. Camera dimensions (mm)

Camera NVIP-5VE-6711/TA/3

100 mm

112 mm

OTHER FUNCTIONS

Temperature Measurement yes

Temperature Alarm yes - for thermal module

Temperature Measurement Zones 10 - for thermal module polygon, line, point

Temperature Measurement Accuracy +/- 2°C

Privacy Zones 4 video mask type: single color

Motion Detection yes

Region of interest (ROI) 8

Video Content Analysis (VCA) tamper, line cross, zone entrance, zone exit, cross counting, Scene Change, Video Blurred,

Video Color Cast, intrusion detection, face detection

for thermal module: line cross, intrusion detection

Image Processing sharpening, vertical flip, horizontal flip, lens distortion correction

Prealarm/Postalarm up to 6 s/up to 120 s

System Reaction to Alarm Events e-mail, e-mail with attachment, saving file on FTP server, saving file on SD card,

alarm output activation, playback of the audio message

Determent white LEDs, flashing light,

audio signaling device (siren), built-in speaker (predefined or custom voice messages)

Restoring default settings via web browser, using reset button, via NMS IPTool software

IR LED

LED Number 2

Range 30 m

Smart IR yes (software support)

WHITE LIGHT ILLUMINATOR

LED Number 1, warm white color

INTERFACES

Audio Input/Output 1 x Jack (3.5 mm)/- built-in microphone/speaker

Alarm Input/Output 1 (NO/NC)/1 relay type (max. 12VDC/300mA)

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 256GB

INSTALLATION PARAMETERS

Dimensions (mm) 112 (Ф) x 100 (H)

Weight 0.7 kg

Degree of Protection IP 66 (details in the user’s manual)

Enclosure vandalproof IK10 impact rating aluminium, white

Power Supply 12 VDC, PoE (IEEE 802.3af, Class 3)

Surge protection TVS 4000 V

Power Consumption

5.5 W,

7.5 W (IR illuminator on),

8 W (white light illuminator on),

10 W (IR and white light illuminators on)

Operating Temperature -30°C ~ 60°C

Humidity max. 95%, relative (non-condensing)

8

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

8

START-UP AND INITIAL IP CAMERA CONFIGURATION

1.4. Package contents

After opening the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not com-

patible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages caused

by the usage of improper power supply source are not covered by the warranty.

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.1 Description of connectors and control tools

1. 100 Mb/s Ethernet port

(PoE RJ-45 connector)

2. Audio input „MIC” (Jack 3.5mm)

3. Alarm input/output

4. Power supply connector 12VDC

5. Base of camera

6. Counter nut

7. Built-in speaker

8. Light sensor

9. Built-in microphone

10. White light and IR illuminator

11. microSD card slot

12. RESET button

7

6

1

2

3

4

5

8

9

10

12

11

9

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2. Power supply connection

The camera can be powered from a commercially available DC power supply, provided that it meets

the technical requirements of the camera. The source must provide stabilized 12VDC voltage, must

allow the consumption of at least 10W of power, and have a barrel DC 2.1/5.5 plug with the correct

polarity of the contacts:

It is also possible to power the camera via the RJ45 network socket, using PoE technology (IEEE

802.3af, Class 3).

Caution!

Do not use power supplies and POE adapters that do not comply with the IEEE 802.3at stand-

ard, the so-called "passive POE" power supplies. Damage resulting from the use of an unsuita-

ble adapter is not covered by the warranty!

2.3 Protection against water ingress

The declared degree of protection applies only to camera housing and the location where the connec-

tion cable enters the inside of the housing.

This means that the connection cable, including sockets, connectors, switches, buttons, and other ele-

ments on this cable, as well as other camera equipment/construction elements (such as hoods, brack-

ets, supports, etc.), are not waterproof. It is the responsibility of the person installing the camera to

protect the elements that require it (and in any case the connection cable) against moisture.

The manufacturer is not responsible for any damages or camera malfunctions resulting from failure to

comply with the above obligation, which also means that they are not covered by the warranty repairs.

The RJ-45 socket cover included in the camera accessories (depending on the version/model) is not a

water protection element. Its purpose is to protect against the ingress of dust and atmospheric moisture

into the socket and prevent accidental disconnections by mechanically stabilizing the network plug in

the RJ-45 socket.

Illustrative drawing

Water protected area Area that needs to be sealed

during installation

10

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

10

2

1

3

4

5

2.4. Camera mounting

To mount a camera please follow the instructions below:

• Unscrew the counter screw (4).

• Remove the camera cover (3), remove the camera from the base (5).

• Put the bracket to the wall in a desired mounting place (with cable hole). Take the drill pattern

and mark future drilling holes for screws and wires.

• Drill holes for screws, wires and base.

• Mount the camera base (5) using the supplied plugs and screws.

• If necessary, unscrew the camera service panel (1), mount microSD card in the socket (2) and

screw the camera service panel (1).

• Connect the camera wires, put camera on the base (5), attach the cover (3) and pre-tighten the

counter screw (4).

• Adjust camera position.

• Tighten to the stop counter screw (4).

Caution!

Pay particular attention to the surface to which is attached the camera to have the appropriate capacity.

Caution!

It is recommended to install the camera using one of the dedicated adapters. The use of an adapter

allows for an aesthetic camera installation, facilitates later servicing and provides a water-protected

space for hiding cables.

START-UP AND INITIAL CAMERA CONFIGURATION

Adapters are additional equipment, to be purchased separately. The characteristics and functions

of the adapter (such as mounting method, space for cables, etc.) depend on its model. The list of

dedicated adapters and their specifications can be found on the camera’s catalog card under the

“Related Products” tab

11

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

11

2.5. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network PoE switch

with PoE support (IEEE 802.3af).

You can also power it from 12VDC power supply compatible with camera power supply specification.

The recommended way to start an IP camera and perform its configuration is a direct connection to the

network switch which is not connected to other devices. To obtain further information about network

configuration parameters (IP address, gateway, network mask, etc.) please contact your network

administrator.

• Connection using network switch with PoE support

• Connection using external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Power supply and

network transmission

Computer

IP Camera

Network PoE Switch

Network transmission

IP Camera

Network transmission

Network Switch Computer

Network transmission

12

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

12

• Connection using external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s

manual.

2.6. Initial configuration via the web browser

The default network settings for NVIP-5VE-6711/TA/3 camera are :

1. IP address - 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer.

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

13

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

13

2.7. Security recommendations for network architecture and configuration

CAUTION!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

14

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

14

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display in

2592 x 1944 resolution and 30 fps speed.

1. CPU Intel i7 3 GHz

2. RAM Memory min. 6 GB

3. VGA card Nvidia GeForce 1GB

4. Operating System Windows 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

• Connecting to the camera for the first time

Enter the IP address of the camera (default 192.168.1.200) in the address bar of the web browser. If the

address is correct and the target device is currently available, the first connection window will be

displayed. In this window, user should read the privacy statement and after reading it, select the

checkbox next to the Already Read button, and press this button.

The acceptance of the privacy statement cannot be omitted. This window only appears the first time

you log in, but it can be displayed again at any time.

Access to the privacy statement can be found in the menu Config > System > Basic information >

Privacy statement.

NETWORK CONNECTION USING WEB BROWSER

15

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

15

NETWORK CONNECTION USING WEB BROWSER

• Device Activation

After accept privacy statement, device activate window appears. In this window user has to set a

password for the web account.

Check the "Activate Onvif user" checkbox to change the password for the Onvif account to the same

password as for the web account.

The password can be up to 16 characters long. While password is entered strength of it displaing on

an ongoing basis by the security level indicator. To ensure the good security of the password, use upper

and lower case letters, numbers and special characters. After entering the correct password twice and

confirming it with the OK button, the administrator password will be saved, the window will close and

the login screen will be displayed.

• User accounts

The Web account is the administrator account created during the activation of the device. It means that

the user logging in, by using the root login and a predefined password and have access to the full

functionality and all available settings in the camera. The account is also used to log in to the camera

via the 6000 series network recorders and NMS (Novus Management System) software using the

LongPolling event method.

The Onvif account is an account used to log in to the camera via the NMS software (Novus

Management System) or using the Onvif or the RTSP protocol. This account is created automatically

during activation of the device, and the default login data are login: "root" and password: "pass".

For security reasons, immediately change the default password for the Onvif account after

activating the device. It is recommended to set the same password in both accounts: the Onvif

account and the web account.

If the user assigns a new password during the device activation but does not check the

"Activate Onvif User" checkbox, the Onvif account will remain with the default login data

(login: root and password: pass).

16

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

16

• Onvif account edition

In order to change the Onvif account password, after logging in, go to the Settings tab in the upper

right corner and then Network > Onvif.

In the Onvif tab, click the Modify button, then in the Edit User window, enter the new password and

confirm with OK button. If the connection to the camera via the NMS software is using the

LongPolling event handling method, the same password for the Onvif account as for the Web account

must be set in this step.

In order to delete the Onvif account, select the user by clicking on the appropriate row in the table, then

click Delete button. Please note that deleting Onvif account means that the camera cannot be added to

NMS software. Add button is used to create new Onvif account.

• Logging in to the camera for the first time

In this window, in order to login to camera, enter the user name root and the newly set administrator

password. In the Stream type field user can select the stream that is displayed in the live view window

after login. The Language field allows to change the interface language. The Forget Password option

allows to log in to the camera if you forget the administrator password and for this is required to know

the answers to the security questions (set in the next step).

After entering appropriate data, click the Login button to login to the web panel of the camera.

NETWORK CONNECTION USING WEB BROWSER

17

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

17

• Safety questions

The next step in logging in for the first time is

entering answers to the security questions.

In the window that appears, select questions

from among those available on the list and enter

your own answers.

Knowing the right answers is essential to

recovering the administrator password.

• Plug-in installation

If the browser has no connected to any of the 6000 series cameras so far, or if an older version of the

plug-in is installed, a message will be displayed in the remote viewing window that the appropriate

plug-in version must be installed.

NETWORK CONNECTION USING WEB BROWSER

This step cannot be omitted. The security question window is displayed only during the first

login, and the only possibility to change the given answers is to restore the factory settings and

go through all stages of the first connection with the camera.

18

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

18

To start plug-in installation, click Here button. Then the browser displays a window asking how to

proceed with the NetAIIPCamera.exe file. Press the Run button to start the plug-in installer.

In the installer window, select the installation language (English by default) and then click Install

button to install plug-in. After installation click the Finish button to close the installer and refresh the

browser window (you can also close and restart the browser).

If after installation and browser window refresh, the same text appears on the screen, go to the browser

Tools (the gearwheel icon in the top right corner), then click Menage add-ones. In the window that

appears click right mouse button on the NetAIIPCamera Control, then click the Enable option and

refresh the browser window.

After completion all of the above steps, preview of the camera in the live view window should appears.

NETWORK CONNECTION USING WEB BROWSER

19

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

19

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1 Displaying live video

1. Camera menu:

• Live - opens the camera live video,

• Config - opens the camera configuration menu,

• Search - opens the camera playback,

• Chart - opens the intelligent image analysis statistics window.

2. The buttons for changing the displayed stream and fluency:

• Allow to change the displayed stream to Main stream, Sub stream.

• Allow you to choose between Real-time, Balanced and Fluent fluency.

3. Alarm icons - icons showing the current status of some camera alarms.

To see what an icon is responsible for, move over it the mouse cursor.

4. Video camera preview window.

5. Thermal camera preview window.

6. Image settings buttons - these buttons change the picture display mode in the live video preview:

Original size Adapt Thermal and video image in division

Proper size Full screen Video image Thermal image

WWW INTERFACE - WORKING WITH IP CAMERA

3

1 2

6 7

4 5

20

NVIP-5VE-6711/TA/3 Quick start guide version 1.1

20

6. Function buttons:

Start/stop live view Enable/disable audio

Snapshot Start Recording

Zoom In (digital) Zoom out (digital)

Enable/disable face detection panel Two-way communication

Activate alarm output

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. Micro SD card installation

Camera supports microSD cards up to a maximum size of 256GB. In order to install the card

properly, please follow the instructions below:

• Turn off the camera power.

• Unscrew the camera service panel (1).

• Mount microSD card in the socket (2).

• Screw the camera service panel (1).

• Turn on the camera.

• Check the SD card by checking its capacity in the “System” -> “SD Card” tab.

ELECTRIC CONNECTORS AND ACCESORIES

2

1

Strona jest ładowana ...

Novus NVIP-5VE-6711/TA/3 Instrukcja obsługi

Novus NVIP-5VE-6711/TA/3 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty