Electrolux EWF1029 Instrukcja obsługi

GB

CZ

H

PL

INSTRUCTION BOOKLET

NÁVOD K OBSLUZE

HASZNÁLATI ÚTMUTATÓ

INSTRUKCJA OBSLUGI

EWF 1029

WASHING MACHINE

AUTOMATICKÁ PRAC

ˇ

KA

AUTOMATA MOSÓGÉP

PRALKA AUTOMATYCZNA

132 990 461

132990461 gb.qxd 17-2-2006 7:54 Pagina 1

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is

particularly important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use

of the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use environmentally

friendly paper.

2

Washing hints 10

Sorting the laundry 10

Temperatures 10

Before loading the laundry 10

Maximum loads 10

Laundry weights 10

Removing stains 11

Detergents and additives 11

Operating sequence 12-13

International wash code symbols 14

Washing programmes 15-16

Maintenance 17

Bodywork 17

Door seal 17

Detergent dispenser drawer 17

Drain pump 17

Water inlet filter 18

Emergency emptying out 18

Frost precautions 18

Something not working? 19-20

Warnings 3

Disposal 4

Tips for environmental protection 4

Technical specifications 4

Installation 5

Unpacking 5

Positioning 5

Water inlet 5

Water drainage 6

Electrical connection 6

Assembly upon a stand kit 6

Your new washing-machine 7

Description of the appliance 7

Detergent dispenser drawer 7

Use 8

Control panel 8

Controls 8-9

Contents

132990461 gb.qxd 17-2-2006 7:54 Pagina 2

3

Installation

•When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact

the Service Centre.

• All internal packing must be removed before using

the appliance. Serious damage may be caused to

the machine or adjacent furniture if the protective

transit devices are not removed or are not

completely removed. Refer to the relevant

paragraph in the instruction book.

• Any electrical work required to install this

appliance must be carried out by a qualified

electrician.

• Any plumbing work required to install this

appliance must be carried out by a qualified

plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the

feet and the floor.

Use

• This appliance is designed for domestic use. It

must not be used for purposes other than those

for which it was designed.

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on each

garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

•Make sure that all pockets are empty. Objects

such as coins, safety pins, pins and screws can

cause extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing

garments in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

Warnings

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

laundry.

• Leave the porthole door slightly ajar when the

appliance is not in use. This preserves the door

seal and prevents the formation of musty smells.

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

• Always unplug the appliance and shut the water

tap after use.

General safety

• Repairs to the machine must be carried out only

by qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• During high temperature wash programmes the

door glass may get hot. Do not touch it!

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children -

danger of suffocation! Keep them out of children’s

reach.

• Keep all detergents in a safe place out of

children’s reach.

•Make sure that children or pets do not climb into

the drum.

•When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

Please read these operating instructions carefully and pay particular attention to the safety notes indicated

below. We recommend that you keep this instruction booklet for future reference and pass it on to any future

owners.

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 3

4

DIMENSIONS Height 85 cm

Width 60 cm

Depth 59 cm

MAXIMUM LOAD Cotton 5.0 kg

Synthetics 2.5 kg

Delicates 2.5 kg

Woollens/Hand Wash 2.5 kg

SPIN SPEED 1000 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz

TOTAL POWER ABSORBED 2200 W

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 0,05 MPa

Maximum 0,80 MPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing

of them properly in appropriate collection

containers.

Machine

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

The symbol on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead it shall be handed over to

the applicable collection point for the recycling of

electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help

prevent potential negative consequences for the

environment and human health, which could

otherwise be caused by inappropriate waste

handling of this product. For more detailed

information about recycling of this product, please

contact your local city office, your household waste

disposal service or the shop where you purchased

the product.

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally cotton soiled laundry may be washed

without prewashing in order to save detergent,

water and time (the environment is protected too!).

• The machine works more economically if it is fully

loaded. Do not overload!

•With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

132990461 gb.qxd 17-2-2006 7:54 Pagina 4

5

Unpacking

All transit bolts and packing must be

removed before using the appliance.

You are advised to keep all transit devices so that

they can be refitted if the machine ever has to be

transported again.

1. Using a spanner, unscrew and remove the two

rear bottom screws. Slide out the two plastic

pins.

2. Lay the machine on its back, taking care not to

squash the hoses. This can be avoided by

placing one of the corner packing pieces

between the machine and the floor.

3. Remove the polystyrene block from the bottom

of the machine and release the two plastic bags.

4. Very carefully slide out the left polythene bag,

removing it towards the right and then

downwards.

5. Very carefully slide out the right polythene bag,

removing it towards the left and then upwards.

6. Set the machine upright and remove the

remaining rear screw. Slide out the relevant pin.

P0001

7. Plug all the holes with the plugs which you will

find in the envelope containing the instruction

booklet.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that the

machine does not touch the wall or other kitchen

units.

Carefully level by screwing the adjustable feet in or

out. Never place cardboard, wood or similar

materials under the machine to compensate for any

unevenness in the floor.

Water inlet

Connect the water inlet hose to a tap with a 3/4"

thread.

Do not use already employed hoses for water

connection.

Important!

Before connecting up the machine to new pipework

or to pipework that has not been used for some

time, run off a reasonable amount of water to flush

out any debris that may have collected in the pipes.

P1088

P1051

P0002

Installation

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 5

6

The other end of the inlet hose which connects to

the machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

Water drainage

The end of the drain hose can be positioned in three

ways:

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

P0022

P0021

The drain hose must not be kinked.

For a correct functioning of the machine the

drain hose must remain hooked on the proper

support piece situated on the top part of the

back side of the appliance.

Electrical connection

This machine is designed to operate on a 220-230

V, single-phase, 50 Hz supply.

Check that your domestic electrical installation can

take the maximum load required (2.2 kW), also

taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility

for damage or injury through failure to

comply

with the above safety precaution.

Should the appliance power supply cable

need to be replaced, this should be carried

out by our Service Centre.

Please ensure that when the appliance is

installed the power supply cable is easily

accessible.

Assembly upon a stand kit

Stand Dimension:

Height: 30 cm.

Width: 60 cm.

Depth: 60 cm.

This appliance can be installed upon a steel Stand

with Drawer to make the loading and unloading of

your laundry easier.

Please ask authorized dealer the suitable stand kit.

P1118

132990461 gb.qxd 17-2-2006 7:54 Pagina 6

7

This new machine meets all modern requirements for effective treatment of laundry with low water, energy and

detergent consumption.

• The automatic cooling of the washing water from 95° to 60°C before draining will prevent old drain pipes

from being deformed.

• The special wool programme with its new delicate wash system treats your woolens with extreme care.

• The unbalance detection device prevents vibration during spinning.

• The ECO valve allows total use of detergent and reduces water consumption so saving energy.

1Detergent dispenser drawer

2 Control panel

3 Door handle

4 Drain pump

5 Adjustable feet

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

Your new washing machine

Description of the appliance

C0063

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 7

8

Use

Programme Option buttons

Depending on the programme, different functions

can be combined. These must be selected after

choosing the desired programme and before

depressing the START/PAUSE button .

When these buttons are pressed, the corresponding

pilot lights come on. When they are pressed again,

the pilot lights go out.

If an incorrect option is selected, the pilot lights flash

for about 2 seconds.

1 Spin speed reduction button , Rinse

hold

Press this button to select one of these options. The

light corresponding to the selected option illuminates.

●

Spin speed

The following speeds are available for the different

fabrics:

- cotton, linen: from 1000 to 500 rpm

- syntetics, wool: from 900 to 450 rpm

- delicates: from 700 to 450 rpm.

●

Rinse hold : by selecting this option the water

of the last rinse is not emptied out to prevent the

fabrics from creasing. When the programme has

finished the phase light is on and the door is

locked. The water must be emptied out.

To do this:

●

turn the programme selector dial to “O”

●

select the drain or spin programme.

Using the spin speed reduction button you can

choose the desired spin.

●

depress START/PAUSE button.

2 “PREWASH” button

Select this programme if you wish your laundry to be

prewashed at 30°C before the main wash (not

available for wool ).

The prewash ends with a short spin in programmes

for cotton and synthetic fabrics, whereas in the

programme for delicate fabrics the water is only

drained.

3 “SUPER RINSE” button

The Super Rinse option can be selected with all

programmes except the wool programme. The

machine will perform 2 additional rinses. This option

is recommended for people who are allergic to

detergents, and in areas where the water is very

soft.

4 “QUICK WASH” button

This button allows you to select the Quick Wash

function, for laundry that is only slightly soiled (not

for wool and economy programme 60E).

The washing time will be reduced according to the

type of fabric and the selected temperature.

Max. load for cotton 3,5 kg.

Control panel

132990461 gb.qxd 17-2-2006 7:54 Pagina 8

9

5“START/PAUSE” button

After having selected the required programme,

press this button to start the machine; the

corresponding pilot light stops flashing and

remains lit.

To interrupt a programme which is running,

depress the Start/Pause button: the

corresponding pilot light starts to flash.

To restart the programme from the point at

which it was interrupted, press the

START/PAUSE button again.

6Programme progress display

When you select the programme, the lights relevant

to the phases that form the programme light up.

After the machine has started, only the running

phase pilot light stays on.

●

/

: when this light comes on this means that

the machine is performing the washing phase. If

you have selected the “Prewash” function, this

light will be on during the prewash phase too.

●

= rinses

●

= spin

●

= drain

●

= end of programme

At the end of the programme the pilot light

illuminates.

The pilot light also flashes in the event of

operating problems:

- 4 flashes = the door has not been closed

- 2 flashes = the machine does not empty

- 1 flash = the machine does not fill

To eliminate the problem, see paragraph “Something

not working”.

7Programme selector dial

The selector is divided into 5 sections:

• Cotton

• Synthetics

• Delicates

• Wool

• Special programmes

The selector dial can be turned either clockwise

or anticlockwise.

Position corresponds to “cold wash”.

Position O corresponds to Reset

programme/Switching OFF of the machine.

At the end of the programme the selector dial

must be turned to position O, to switch the

machine off.

ATTENTION!

If you turn the programme selector dial to another

programme when the machine is working, the lights

of the programme progress display start to flash.

The machine will not perform the new selected

programme.

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 9

10

Washing hints

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

whites, coloureds, synthetics, delicates, woollens.

Temperatures

95°

for normally soiled white cottons and linen

(e.g. tea cloths, towels, tablecloths,

sheets...)

60° for normally soiled, colour fast garments

(e.g. shirts, night dresses, pyjamas....) in

linen, cotton or synthetic fibres and for

lightly soiled white cotton (e.g.

underwear).

(cold)for delicate items (e.g. net curtains), mixed

30°-40° laundry including synthetic fibres and

woollens.

Before loading the laundry

Never wash whites and coloureds together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins, pins).

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes.

Remove persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Treat curtains with special care. Remove hooks or

tie them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

programme charts.

General rules:

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Delicate fabrics and woollens: drum no more than

one third full.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe 1200 g

napkin 100 g

quilt cover 700 g

sheet 500 g

pillow case 200 g

tablecloth 250 g

towelling towel 200 g

tea cloth 100 g

night dress 200 g

ladies’ briefs 100 g

man’s work shirt 600 g

man’s shirt 200 g

man’s pyjamas 500 g

blouse 100 g

men’s underpants 100 g

Removing stains

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Blood: treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Dried grease stains: moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites

and fast coloureds only).

Grass: soap lightly and treat with bleach (whites and

fast coloureds only).

Ball point pen and glue: moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

Lipstick: moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

132990461 gb.qxd 17-2-2006 7:54 Pagina 10

11

Red wine: soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

residual marks with bleach.

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

All commonly available washing machine detergents

may be used in this appliance:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (60°C max)

and woollens,

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of

fabric, or special for woollens only.

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

If using concentrated powder or liquid detergents, a

programme without prewash must be selected.

The washing machine incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Pour liquid detergent into the dispenser drawer

compartment marked just before starting the

programme.

Any fabric softener or starching additives must be

poured into the compartment marked before

starting the wash programme.

Follow the product manufacturer’s

recommendations on quantities to use and do not

exceed the «MAX» mark in the detergent

dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Water hardness is classified in so-called “degrees”

of hardness. Information on hardness of the water in

your area can be obtained from the relevant water

supply company, or from your local authority.

Follow the product manufacturers’ instructions on

quantities to use.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 11

12

4. Select the required programme

Turn the programme selector dial to the required

programme.

5. Select the required options

The light corresponding to the depressed button

illuminates.

6. Start the programme

To start the selected programme, press the

START/PAUSE button .

The light

/

illuminates.

Operating sequence

Before the first wash we recommend that you pour 2

litres of water into the main wash compartment

of the detergent drawer in order to activate the ECO

valve. Then run a cotton cycle at 95°C, with the

machine empty, in order to remove any

manufacturing residue from the drum and tub.

Pour half a measure of detergent into the main wash

compartment and start up the machine.

1. Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

main wash compartment .

If you wish to carry out the prewash, pour detergent

or the stain remover into the appropriate

compartment marked .

3. Measure out the additive

If required, pour fabric softener into the

compartment marked , without exceeding the

«MAX» mark.

C0065

C0064

P0004

132990461 gb.qxd 17-2-2006 7:54 Pagina 12

13

7. How to change a programme during

its cycle

Before you make any change, you must pause the

washing machine by pressing the START/PAUSE

button.

It is possible to change any phase before the

programme carries it out.

When the programme has started, you can only

reset it by turning the programme selector dial to O

and then you can select the new programme. The

washing water remains in the tub. Start the new

programme by depressing the START/PAUSE

button.

Note: To drain the water before starting the new

cycle, you have to cancel the programme and select

the DRAIN cycle.

8. Cancelling a programme

Turn the selector dial to O to cancel a programme

which is running. Now you can select a new

programme.

9. Opening the door after the

programme has started

First set the machine to PAUSE by pressing the

START/PAUSE button .

If the door does not open, this means that the

machine is already heating, that the water level is

above the bottom edge of the door or that the drum

is turning.

If you cannot open the door but you need to open it

you have to switch the machine off by turning the

selector dial to “O”. After about 3 minutes the door

can be opened (pay attention to the water level and

temperature!).

10. At the end of the programme

The machine stops automatically.

The START-PAUSE pilot light goes out and the

END pilot light comes on. The door can be

opened.

If the Rinse Hold option has been selected, the

END pilot light remains lit and the door is locked

to indicate that the water must be emptied out

before opening the door.

To do this turn the programme selector dial to “O”

and then to programme (drain) or (short spin).

The spin programme is performed at the maximum

speed.

Switch the machine off by turning the programme

selector dial to “O”.

Remove the laundry from the drum and carefully

check that the drum is empty so as to avoid any

forgotten items being damaged in a subsequent

wash (e.g. shrinking) or their colour running into a

load of whites.

If you do not intend to carry out another wash, close

the water tap.

Leave the door open to prevent the formation of

mildew and unpleasant smells.

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 13

14

International wash code symbols

These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.

Energetic wash

Delicate wash

Max. wash

temperature

95°C

Max. wash

temperature

60°C

Max. wash

temperature

40°C

Max. wash

temperature

30°C

Hand wash Do not

wash

at all

Bleaching Bleach in cold water Do not bleach

Ironing Hot iron

max 200°C

Warm iron

max 150°C

Lukewarm iron

max 110°C

Do not iron

Dry cleaning Dry cleaning

in all solvents

Dry cleaning in

perchlorethylene,

petrol, pure alcohol,

R 111 & R 113

Dry cleaning

in petrol,

pure alcohol

and R 113

Do not

dry clean

Drying Flat On the line On clothes

hanger

Tumble dry

high

temperature

low

temperature

Do not

tumb

le dr

y

A

P

F

95

60

40

30

132990461 gb.qxd 17-2-2006 7:54 Pagina 14

15

ENGLISH

Programme table

* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending

on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.

It refers to the highest temperature for each wash programme.

** In compliance with EC directive 92/75, the consumption figures indicated on the energy label refer to the

wash programme 60°E.

Washing programmes

Type of

laundry

Max

load

Programme/

temperature

Description

of programme

Available

options

Energy

kWh

Water

lt

Duration

h/min.

Consumption*

White cotton:

e.g. sheets,

tablecloths,

household linen

White Cotton

95°C

5 kg

2.0 53 140

Main wash at

95°C

3 rinses

Long spin

White/Coloured

cotton:

e.g. shirts, blouses,

underwear, towels

White/Coloured

Cotton

60°E**

5 kg

0.95 49 130

Main wash at

60°C

3 rinses

Long spin

Coloured cottons

Coloured

cottons

30°-40°-60°C

5 kg

1.2 49 120

Main wash at

30°-40°-60°C

3 rinses

Long spin

Synthetic fabrics:

e.g. shirts, blouses,

underwear

Synthetics

30°-40°-60°C

2.5 kg

0.9 54 90

Main wash at

30°-40°-60°C

3 rinses

Short spin

Delicate fabrics:

e.g. acrylic fabrics,

viscose, polyester,

synthetic blends

Delicates

30°-40°C

2.5 kg

0.5 55 60

Main wash at

30°-40°C

3 rinses

Short spin

Wool

-40°C

2 kg

0.45 55 55

Main wash at

- 40°C

3 rinses

Short spin

132990461 gb.qxd 17-2-2006 7:54 Pagina 15

16

Programme table

SPECIAL PROGRAMMES

* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on

the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.

Programme

selector dial

position

Rinses

Programme

description

Additional

functions

Wash load

max.

Energy

kWh

Water

lt

Duration

min.

Consumptions*

For rinsing hand

washed items

3 rinses with liquid

additive, if required

Short spin at max.

speed

5 kg 0.05 55 30

/

--1.5

5 kg

--5

Drain

For emptying out

the water of the

last rinse of

programmes with

option

Separate spin for

cotton,

synthetics,

delicates and

wool/handwash

Water draining

Drain and short spin at

max. speed

Spin

/

---

For cancelling

the programme

which is running

or to switch the

machine off.

O

Reset/Off

132990461 gb.qxd 17-2-2006 7:54 Pagina 16

17

Bodywork

Clean the outside of the machine with soap and

water only. Rinse with clean water and dry with a

soft cloth.

Important: do not use methylated spirits, solvents

or similar products to clean the bodywork.

Door seal

Check from time to time the door seal and eliminate

eventual possible objects that could be trapped in

the fold.

Detergent dispenser drawer

After a while, detergents and fabric softeners leave

deposits in the drawer.

Clean the drawer from time to time by rinsing it

under a running tap. To remove the drawer from the

machine, press the button in the rear left-hand

corner.

To facilitate cleaning, the top part of the additive

compartments can be removed.

C0067

C0066

P1050

Detergent can also accumulate inside the drawer

recess: clean it with an old toothbrush. Refit the

drawer after cleaning.

Drain pump

The pump should be inspected if

• the machine does not empty and/or spin

• the machine makes an unusual noise during

draining due to objects such as safety pins, coins

etc. blocking the pump.

Proceed as follows:

• Disconnect the appliance.

• If necessary wait until the water has cooled down.

• Open the pump door.

• Place a container close to the pump to collect any

spillage.

• Release the emergency emptying hose, place it in

the container and remove its cap.

• When no more water comes out, unscrew the

pump cover and remove the pump. Always keep a

rag nearby to dry up spillage of water when

removing the pump.

P0038

Maintenance

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 17

18

• Remove any objects from the pump impeller by

rotating it.

• Put the cap back on the emergency emptying

hose and place the latter back in its seat.

• Screw the pump cover fully in.

• Close the pump door.

Water inlet filter

If you notice that the machine is taking longer to fill,

check that the filter in the water inlet hose is not

blocked.

Turn off the water tap.

Unscrew the hose from the tap.

Clean the filter with a stiff brush.

Screw the hose back onto the tap.

P1090

Emergency emptying out

If the water is not discharged, proceed as follows to

empty out the machine:

• pull out the plug from the power socket;

• close the water tap;

• if necessary, wait until the water has cooled down;

• open the pump door;

• place a bowl on the floor and place the end of the

emergency emptying hose into the bowl. Remove

its cap. The water should drain by gravity into the

bowl. Whe the bowl is full, put the cap back on the

hose. Empty the bowl. Repeat the procedure until

water stops flowing out;

• clean the pump if necessary as previously

described;

• replace the emergency emptying hose in its seat

after having plugged it;

• screw the pump cover again and close the door.

Frost precautions

If the machine is installed in a place where the

temperature could drop below 0°C, proceed as

follows:

• Remove the plug from the socket.

• Close the water tap and unscrew the water inlet

hose from the tap.

• Place the end of the emergency emptying hose

and that of the inlet hose in a bowl placed on the

floor and let water drain out.

• Screw the water inlet hose back on and reposition

the emergency emptying hose after having put the

cap on again.

By doing this, any water remaining in the machine is

removed, avoiding the formation of ice and,

consequently, breakage of the affected parts.

When you use the machine again, make sure that

the ambient temperature is above 0°C.

Important!

Every time you drain the water through the

emergency emptying hose you must pour 2 litres of

water into the main wash compartment of the

detergent drawer and then run the drain

programme. This will activate the ECO VALVE

device avoiding that part of the detergent remains

unused at next washing.

132990461 gb.qxd 17-2-2006 7:54 Pagina 18

19

Problems which you can resolve yourself, before calling the After Sales Service.

During machine operation it is possible that the end light starts to flash:

4 flashes= the door has not been closed

2 flashes= the machine does not empty

1 flash= the machine does not fill.

Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If after

all checks, the problem persists, contact your local Service Centre.

Problem Possible cause

• The machine does not start up:

• The door is not firmly closed.

• The machine is not plugged in or there is no power

at the socket.

• The main fuse has blown.

• The programme selector dial is not positioned correctly.

• The START/PAUSE button has not been depressed.

• The machine does not fill:

• The water tap is closed.

• The inlet hose is squashed or kinked.

• The filter in the inlet hose is blocked.

• The door is not properly closed.

• The machine fills then empties

immediately:

• The end of the drain hose is too low. Refer to

relevant paragraph in “water drainage” section.

• The machine does not empty

and/or does not spin:

• The drain hose is squashed or kinked.

• The option has been selected.

• The drain pump is clogged.

• There is water on the floor:

• Too much detergent or unsuitable detergent

(creates too much foam) has been used.

• Check whether there are any leaks from one of the

inlet hose fittings. It is not always easy to see this

as the water runs down the hose; check to see if it

is damp.

• The drain hose is damaged.

• The cap on the emergency emptying hose has not

been replaced after cleaning the pump.

• Unsatisfactory washing results:

• Too little or too much detergent has been used.

• An unsuitable detergent has been used.

• Stubborn stains have not been treated prior to

washing.

• The correct programme or temperature was not

selected.

• Excessive laundry load.

• The machine vibrates or is noisy:

• The transit bolts and packing have not been removed.

• The support feet have not been adjusted.

• The laundry is not evenly distributed in the drum.

• Maybe there is very little laundry in the drum.

Something not working?

ENGLISH

132990461 gb.qxd 17-2-2006 7:54 Pagina 19

20

If you are unable to identify or solve the problem,

contact our service centre. Before telephoning,

make a note of the model, serial number and

purchase date of your machine: the Service Centre

will require this information.

P0042 BD

Problem

Possible cause

•Water is not visible in the

machine:

• The machine, which is the result of modern

technology, runs in a very economical way with

low water consumption. Performance is

nevertheless excellent.

• Spinning starts late or the

machine does not spin:

• The electronic unbalance detection device has cut

in because the laundry is not evenly distributed in

the drum. The laundry is redistributed by reverse

rotation of the drum. This may happen several

times before the unbalance disappears and normal

spinning can resume. If, after 10 minutes, the

laundry is still not evenly distributed in the drum,

the machine will not spin. In this case, redistribute

the load manually and select the spin programme.

• The machine makes an unusual

noise

• The machine is fitted with a type of motor which

makes an unusual noise compared with other

traditional motors. This new motor ensures a softer

start and more even distribution of the laundry in

the drum when spinning, as well as increased

stability of the machine.

• Detergent residue is left after the

wash cycle

• This is most probably due to non soluble

components contained in modern detergents. It is

not a sign of inadequate rinsing. Brush or shake

the garments and, if necessary, wash them again.

• Foam remains after the last rinse

•Modern detergents can produce foam even after

rinsing, but this will not affect the quality of the

wash.

• The door will not open:

• The programme is still running, the drum is turning.

• The door lock has not been released.

• The water level is above the bottom edge of the

door.

• The machine is heating the water.

132990461 gb.qxd 17-2-2006 7:54 Pagina 20

Strona jest ładowana ...

Electrolux EWF1029 Instrukcja obsługi

Electrolux EWF1029 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty