Fieldmann FZS 3005-B Instrukcja obsługi

FZS 3005 B

EN 2

FZS 3005 B

English .................................................................................................................................................................................3–24

Čeština .............................................................................................................................................................................25–46

Slovenčina ..................................................................................................................................................................... 47–68

Magyarul ........................................................................................................................................................................69–90

Polski ................................................................................................................................................................................91–112

Slovenščina ...............................................................................................................................................................113–136

EN

PETROL BRUSH CUTTER USER'S MANUAL

3

Table of Contents

Petrol brush cutter

USER'S MANUAL

Thank you for purchasing this petrol brush cutter. Before you start using it, please

carefully read this user's manual and save it for possible future use.

CONTENTS

1. GENERAL SAFETY INSTRUCTIONS ........................................................................................................................5

Important safety information .................................................................................................................................5

Packaging .......................................................................................................................................................................5

User's manual .................................................................................................................................................................5

2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE ................................................................6

3. OPERATING INSTRUCTIONS ....................................................................................................................................7

Safety instructions ........................................................................................................................................................7

Safety instructions – fuel ........................................................................................................................................... 7

Safety instructions – cutting tools .........................................................................................................................8

4. DESCRIPTION OF THE MACHINE ..........................................................................................................................9

Included contents: .....................................................................................................................................................9

5. ASSEMBLY .......................................................................................................................................................................10

Installing the string trimmer head ......................................................................................................................11

Winding string trimmer line on to the trimmer head ............................................................................. 11

Installing the metal blade .....................................................................................................................................12

6. MIXING THE FUEL MIX .............................................................................................................................................12

Storing fuel .....................................................................................................................................................................13

7. PREPARING FOR OPERATION ..............................................................................................................................13

Points to check before starting work ...............................................................................................................13

8. STARTING THE BRUSH CUTTER ..............................................................................................................................13

Procedures for starting and stopping the engine ....................................................................................14

Starting a cold engine ....................................................................................................................................14

Starting a warm engine ..................................................................................................................................14

Controlling the speed of the string trimmer head / metal blade ............................................15

Stopping the engine ........................................................................................................................................15

9. CUTTING ..........................................................................................................................................................................15

Cutting with the nylon string trimmer head .................................................................................................16

Trimming grass ........................................................................................................................................................16

Clearing and trimming edges .......................................................................................................................16

Cutting using the blade .........................................................................................................................................17

Cutting weeds ........................................................................................................................................................17

EN 4

FZS 3005 B

Table of Contents

10. MAINTENANCE AND STORAGE ..........................................................................................................................18

Maintaining the machine .....................................................................................................................................18

Servicing .........................................................................................................................................................................18

Warranty does not cover: ......................................................................................................................................18

Storage ............................................................................................................................................................................18

11. WHAT TO DO "WHEN"... ............................................................................................................................................19

12. DISPOSAL ........................................................................................................................................................................21

13. DECLARATION OF CONFORMITY ......................................................................................................................22

14. TECHNICAL SPECIFICATIONS ...............................................................................................................................23

EN

PETROL BRUSH CUTTER USER'S MANUAL

5

General safety instructions

1. GENERAL SAFETY INSTRUCTIONS

Important safety notice

Carefully unpack the product and take care not to throw away any part of the packaging before you ﬁ nd all

the parts of the product.

Store the product in a dry place out of reach of children.

Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical

shock, a ﬁ re and/or serious injuries.

Packaging

The product is packed in a package that prevents damage during transport. This package is a resource and so

can be handed over for recycling.

User’s Manual

Before you start working with the machine, read the following safety and usage instructions. Acquaint yourself

with the operating elements and the correct use of the machine. Keep the user’s manual in a safe place where

it can be easily retrieved for future use. Save the original packaging, including the internal packing material,

warranty card and proof of purchase receipt at least for the duration of the warranty. If you need to ship this

machine, pack it in the original cardboard box to ensure maximum protection during shipping or transport

(e.g. when moving or when you need to send this product for repair).

Note: If you hand over the machine to somebody else, do so together with the user’s manual.

Following the instructions in the included user’s manual is a prerequisite for the proper use of the machine.

The user’s manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not

following the instructions in this manual.

EN 6

FZS 3005 B

Explanation of instruction labels on the machine

2. EXPLANATION OF INSTRUCTION LABELS ON

THE MACHINE

Carefully read the manual before use

While working use protective aids

General danger warnings!

Caution, recoil!

Keep other persons (particularly children)

and animals out of range, at least 15 m

from the working area.

EN

PETROL BRUSH CUTTER USER'S MANUAL

7

Operating instructions

3. OPERATING INSTRUCTIONS

Safety instructions

Read carefully!

Always wear a safety helmet, safety gloves, protective clothing (cut-resistant trousers) and safety footwear.

Keep the machine out of children’s reach.

Never run the engine if there is only petrol in the petrol tank.

Never pour in fuel if the engine is running or if it is still hot. Only ﬁ ll up the engine when it is cold.

Store fuel in a closed container in a dry and cool place.

Adhere to safety directives.

Check the work area prior to every use. Remove items that could be deﬂ ected or that could jam in the

machine.

When working, all other persons must be outside the range of at least 15 meters.

Never use the machine without the protective cover (of the cutting blade) installed.

Never ﬁ ll up the petrol tank so that it is completely full.

The fuel tank cap must be ﬁ rmly tightened to prevent fuel from leaking out.

Do not permit the machine to run at full speed if the petrol tank is empty.

Never turn off the machine suddenly if it is running at full speed.

Do not use the machine if it is damaged in any way. Contact a qualiﬁ ed service centre.

When carrying, hold the entire machine because holding it only by the fuel tank is dangerous and may result

in damage to the petrol tank and a ﬁ re.

Always hold the brush cutter with both hands.

Never place a hot brush cutter on to dry grass.

Smoking is forbidden when working with the machine.

Safety instructions

Fuel

During transport, the fuel tank of the brush cutter must be empty.

Only transport fuel in approved canisters.

Regularly inspect the fuel tank cap. It must be tightened and fuel must not leak out

Protect the environment: take care to avoid a fuel spill and soil contamination.

Start the machine at least 3 metres away from where you ﬁ lled it up with fuel.

Never ﬁ ll up fuel in closed rooms. There must be sufﬁ cient ventilation in the room, risk of an explosion.

Do not inhale fuel vapours. Wear safety gloves when pouring in fuel.

Regularly replace and clean your protective clothing.

EN 8

FZS 3005 B

Operating instructions

Safety instructions

Cutting tools

When installing the cutting tool, check the condition of the blade. If it is damaged (cracked, bent, broken off,

etc.), replace it.

After installing the blade, check again that the hole in the blade is level with the arm of the blade tang.

Spin the blade, check again that the blade has no tendency to rotate irregularly.

Check that the blade is installed with the sharp edge moving in the direction of rotation. Never install it the

other way around.

Check that the cutting tool is properly assembled by turning it without load (1 minute is enough).

An appropriate blade must be selected for the material that is to be cut.

Never push the blade against objects when in operation. Material must be cut at reasonable speed.

If you hear an unusual noise or the machine vibrates abnormally, stop working and identify the cause.

Do not stop the machine while the blade is cutting a material. There is a danger of damaging the machine.

The cutting tool must be ﬁ tted with an appropriate guard.

ATTENTION! If instructions are not followed, there is a danger of a serious or even fatal

Injury to persons!

Acquaint all persons working with this machine with the operation of the machine and the safety

instructions.

EN

PETROL BRUSH CUTTER USER'S MANUAL

9

4. DESCRIPTION OF THE MACHINE

Description of the machine

1. Metal blade /

semi-automatic string trimmer head

2. Trimmer line cutter

3. Protective safety guard

5. Handle mount

6. Throttle trigger lock

7. Throttle trigger

8. Power switch

9. Throttle safety switch

10. Engine

11. Fuel tank cap

12. Fuel tank

13. Shoulder strap hitch

14. Choke control lever

15. Fuel primer bulb

Included contents:

Brush cutter, string trimmer head metal blade, shoulder strap, calibrated fuel mixing container, tool set

12

3

4

5

6

7

8

9

12

11

10

14

13

EN 10

FZS 3005 B

Assembly

5. ASSEMBLY

Install the protective guard on to the shaft using

the supplied screws and nuts (see ﬁ g. 2)

Install the handle into the mount (see ﬁ g. 3).

The handle can be moved along the shaft. In this

way, everybody can select the ideal comfortable

working position. After selecting the ideal working

position, tighten the screws. Fasten the control

cable to the shaft using the supplied draw bands.

Fig. 3

Fig. 2

Bolt

Nut

EN

PETROL BRUSH CUTTER USER'S MANUAL

11

Assembly

Installing the string trimmer head

Lock the shaft in place by inserting the hex key

(see ﬁ g. 4). To achieve this, it is necessary to align

the hole in the protective guard with the hole in

the shaft and insert the hex key. Align the holes by

turning the protective guard.

Install the individual components in the following

order:

1. cogged retaining washer A (also equipped

with a retaining hole)

2. string trimmer head

Screw the string trimmer head on to the shaft by

turning it clockwise (attention: reverse thread) and

tighten ﬁ rmly.

Take the hex key out of the retaining hole.

Winding string trimmer line on to the

trimmer head

1. Push in the retaining latches on the side of the

head and take off the cover (see ﬁ g. A & B)

2. Take the spool out of the string trimmer head.

Prepare about 2-3 m of string trimmer line with

a diameter of 2.4 mm.

3. Bend the string trimmer line in the middle and

secure the bend in the groove (see ﬁ g. C)

4. Wind both ends in parallel on to the spool in

a clockwise direction. Secure the ends of the

wound on string trimmer line into the prepared

holes (see ﬁ g. D)

5. Return the spool back into the string trimmer

head and secure in place with the cover

(see ﬁ g. E and F)

WARNING!

Use only good quality nylon string trimmer line

with a diameter of 2.4 mm. Never use wire or wire-

reinforced string trimmer line instead of the nylon

string trimmer line. Only use the original string trimmer

head.

B

CD

E F

A

Fig. 4

Hex key 4 mm

Shaft

Protective cover

Cogged retaining

washer A

Locking hole

String trimmer head

EN 12

FZS 3005 B

Assembly | Mixing the fuel mix

Installing metal blade

Lock the shaft in place by inserting the included

4mm hex key (see Fig. 5). To achieve this, it is

necessary to align the hole in the protective guard

with the hole in the shaft and insert the hex key.

Align the holes by turning the protective guard.

Install the individual components in the following

order:

1. Cogged retaining washer A (also equipped

with a retaining hole)

2. metal blade

3. retaining washer B

4. cup cover

5. lock nut

Make sure that the blade is correctly seated in the

distancing part of the cogged retaining washer A

Using the supplied socket wrench, turn the blade

fastening nut clockwise (attention: reverse thread)

until it is securely tightened.

Take the hex key out of the retaining hole.

WARNING!

IN THE EVENT OF EXCESSIVE VIBRATIONS – IMMEDIATELY STOP THE ENGINE

Excessive vibrations of the blade mean that this blade is not installed correctly. Immediately turn off the engine

and check the blade.

An incorrectly installed blade may cause injuries.

Only use original accessories when performing maintenance or servicing this product.

6. MIXING THE FUEL MIX

WARNING!

Never pour fuel into the fuel tank in a closed and unventilated location.

Do not pour fuel in the vicinity of an open ﬂ ame or a source of sparks.

Do not overﬁ ll the petrol tank. Before starting the engine, make sure that all spilt fuel is wiped away.

If the engine is hot, DO NOT POUR IN FUEL.

For this type of two-stroke engine a mixture of lead-free petrol and two-stroke engine oil is used at a ratio of

40:1.

ATTENTION! A fuel mix that is mixed at a ratio other than 40:1 may damage the engine. Make sure that this

fuel mix is mixed correctly.

Fig. 5

Hex key 4 mm

Shaft

Protective cover

Cogged retaining

washer A

Retaining washer B

Cup cover

Lock nut

Locking hole

Metal blade

EN

PETROL BRUSH CUTTER USER'S MANUAL

13

Mixing the fuel mix | Preparing for operation | Starting the brush cutter

When mixing petrol with two-stroke engine oil, use only petrol containing NO ETHANOL or METHANOL (types

of alcohols).

Use quality petrol with an octane number of 95 or higher. This will help prevent possible damage to the fuel

system and other parts of the engine.

Storing fuel

Only store fuel in a clean, safe and approved canister. Inform yourself about and adhere to local directives related

to the type and storage of canisters ﬁ lled with fuel.

IMPORTANT

Fuel for two-stroke engines may separate. Prior to every use, thoroughly shake the canister with fuel.

Stored fuel ages. Do not mix more fuel than you expect to consume within one month.

7. PREPARING FOR OPERATION

IMPORTANT:

Follow instructions for preparing the fuel mix! Not following these instruction may damage the engine! Do not

use fuel that has been stored for longer than two months. A fuel mix stored for longer than two months will cause

problems at start up and lower engine performance. If the fuel mix is stored for longer than two months, it should

be removed and new fuel must be used.

Points to check before starting work

1. Check whether any screws, nuts and installation elements are loose. Tighten any loose screws.

2. Check whether the air ﬁ lter is dirty. Prior to starting work, remove all dirt from the air ﬁ lter.

3. Make sure that the plastic head guard and the blade is securely fastened in place.

4. Check the fuel tank for leaks.

5. Check the blade or the string trimmer head for damage.

8. STARTING THE BRUSH CUTTER

WARNING!

Prior to starting the engine, make sure that the cutting blade/string trimmer head can move freely and is not

touching any foreign objects.

When the engine is idling, the cutting tool must not be turning. Otherwise, contact an authorised service

centre to perform an inspection and remedy the problem.

Prior to starting the engine, make sure that the throttle trigger moves freely.

EN 14

FZS 3005 B

ATTENTION: Hold the brush cutter ﬁ rmly with both hands. Always stand so that your body is on the left of

the shaft tube. Never hold the handle with crossed arms. These instructions also apply to left-handers.

ATTENTION: Exposure to vibrations may damage the health of persons that suffer from circulatory or

nerve system problems. If any physical problems become evident, such as desensitisation, loss of sensitivity,

loss of usual strength or changes in skin colour, please contact a doctor.

These systems usually manifest themselves on ﬁ ngers, hands or wrists.

PROCEDURES FOR STARTING AND STOPPING THE ENGINE

Starting a cold engine

1. Set the power switch to the "START" position.

(see ﬁ g. 6)

2. Repeatedly push down the fuel primer bulb

(5 to 10 presses), until the fuel gets to the

carburettor. (see ﬁ g. 7)

3. Move the choke lever upwards to the "OFF"

position (=air supply turned off, i.e. choke turned

on). (see ﬁ g. 7)

4. Lean the brush cutter against the ground so that

it is stable and pull on the handle of the starting

cord until the engine rotates (the engine will show

signs of attempting to start).

5. At this point, push the choke lever downwards to

the "ON" position (=air supply turned on, i.e. choke

turned off) and start the engine by repeatedly

pulling on the starting cord.

ATTENTION! Spinning the engine for too long

with the choke lever in the OFF position will result

in ﬂ ooding of the engine and problems with

starting it up.

6. Prior to starting work, leave the engine to warm

up for a few minutes to get up to operating

temperature.

Starting a warm engine

1. Set the power switch to the "START" position.

2. Pull on the handle of the starting cord until the

engine starts up. DO NOT USE THE CHOKE!

Starting the brush cutter

Fig. 7

Fuel primer

bulb

Choke control lever

Fig. 6

Safety

throttle safety switch

Throttle

lever

Power switch

EN

PETROL BRUSH CUTTER USER'S MANUAL

15

ATTENTION! In the event that the fuel in the fuel tank was completely used up, after pouring in fuel, repeat

the steps for STARTING A COLD ENGINE.

Controlling the speed of the string trimmer head / metal blade

To increase speed, ﬁ rst use the palm of your hand to push down the throttle safety switch and then use your

ﬁ nger to pull on the throttle trigger (see ﬁ g. 6)

The throttle trigger can be locked in place using the half-throttle lock (ﬁ g. 1, bod 5)

To lower the speed, release the throttle trigger

Stopping the engine

Move the power switch to the STOP position.

WARNING!

The engine exhaust fumes contain chemical substances that are damaging to health. Never inhale these fumes.

Always start the brush cutter outdoors.

9. CUTTING

WARNING!

When working with any string trimmer or brush cutter model, there is a danger of deﬂ ecting stones, metal or

small objects and the cut material. Carefully read all the safety directives.

Follow all the instructions provided in this user’s manual.

WARNING!

Use head, eye, face and hearing protection. Use appropriate footwear that will protect your feet and which will

ensure a ﬁ rm stance on slippery surfaces. Do not wear ties, jewellery or loose clothing that could become caught

in the moving parts of the tool. Do not wear footwear with an open tip. Do not work barefoot or with bare legs. In

certain situations you must use full face and head protection.

Take care to avoid recoil and jamming of the blade.

WARNING

Always use the shoulder strap.

Set the shoulder strap and its hitch on the tool so that the brush cutter is suspended several centimetres above

the terrain. The head of the brush cutter and the metal guard must be level in all directions. Hang the brush cutter

on the right side of the body.

DANGER ZONE

NOBODY APART FROM THE OPERATOR MAY ENTER THE DANGER ZONE OF A 15 METRE RADIUS. THE OPERATOR

MUST USE APPROPRIATE EYE, HEARING, FACE, FOOT, LEG AND BODY PROTECTION. PERSONS LOCATED IN

THE DANGER ZONE OR IN THE RISK ZONE AFTER THE DANGER ZONE MUST USE EYE PROTECTION AGAINST

DEFLECTED OBJECTS. THE RISK IS REDUCED WITH INCREASING DISTANCE FROM THE DANGER ZONE.

Starting the brush cutter | Cutting

EN 16

FZS 3005 B

Cutting

CUTTING WITH THE NYLON STRING TRIMMER HEAD

The string trimmer head rotates CLOCKWISE.

The trimmer line is extended out semi-automatically. While trimming, simply gently tap the head on the

ground, which will push down the button on the underside of the head and the string trimmer line will slide

out. The string trimmer line is then shortened to the maximum permitted length on the blade integrated in

the plastic guard.

Trimming grass

During this activity, carefully move the trimmer into the material that you wish to trim. Slowly tilt the head so

that the trimmed material is ejected away from you. If you are trimming all the way up to obstacles such as

fences, walls and trees, then approach at such an angle that all material is ejected away from you. Slowly

move the head with the nylon string trimmer line from right to left until the grass is trimmed all the way to the

obstacle but avoid the string trimmer line coming into contact with the obstacle.

When trimming in the vicinity of a wire fence or enclosure, proceed carefully so as not to come into contact

with the wires. If you exceed the minimum distance from the fence, the string trimmer line will be shortened

after impact.

When cutting weeds, it is possible to cut one stem at a time. Place the trimmer head with string trimmer line

at the bottom part of the weed - never the top because the stem may start quivering and the string trimmer

line may become caught in it. Rather than attempting to cut the weed directly, it is better to use only the end

of the string trimmer line and to cut the stem slowly.

Clearing and trimming edges

Both these tasks are performed using the head with the nylon line tilted at large angle. Clearing means

removing the top vegetation after which only soil remains.

Trimming edges means trimming the grass at the edge of lawns that extends on to footpaths and roads.

While clearing and trimming edges, hold the tool at a steep angle and in a position where dirt, cut material

and stones will not be ejected backwards towards you in the event that they ricochet from a hard surface.

Despite the pictures showing how to perform clearing and trimming of edges, every user must ﬁ nd their own

position that will suit their body dimensions and working conditions.

WARNING

If a head with a nylon line is used, the correct protective guard must be ﬁ tted. If the nylon line extends out too far,

it may start ﬂ uttering. If you use a head with a nylon line, always use the protective plastic guard with the cutter

blade.

WARNING

Be very careful when working above soil or gravel because the nylon line may deﬂ ect small stones at a very high

speed.

The protective guard on this tool cannot stop objects that ricochet off hard surfaces.

WARNING

Do not trim in places where there are wires and wire mesh. Use protective aids. Do not trim in locations where

you cannot see what the trimmer is trimming.

EN

PETROL BRUSH CUTTER USER'S MANUAL

17

Cutting

CUTTING USING THE BLADE

Cutting weeds

This is cutting performed by a pendular movement of the blade in an arch shape. In this way you can quickly

clear a large area of dense grass and weed. Brush cutting should be used for cutting large and tough weeds

or woody vegetation.

Brush cutting may be performed in both directions or only in one direction, which will mean that the cut

material will be ejected away from you. With this type of cutting, the part of the blade moving away from you

will do the work. Slightly tilt the blade down to the same side. If you will be brush cutting in both directions,

you will be hit by some deﬂ ected material.

Note: Do not use the brush cutter blade for cutting trees with a diameter larger than 12 mm.

WARNING

DO NOT TOUCH THE FOLLOWING OBJECTS WITH THE BLADE:

METAL POLES, ELECTRICAL WIRE, RUBBER, MASONRY, STONES, FENCES

WARNING

Do not cut if the metal blade is blunt, cracked or damaged.

Before starting to cut, check that there are no obstacles in the work area such as rocks, metal poles or wound up

wires. If you cannot remove these obstacles, mark them out so that they do not come in contact with the blade.

Rocks or metal objects will blunt or damage the blade. Wires may wind on to the blade head or may be deﬂ ected

and cause injuries.

EN 18

FZS 3005 B

Maintenance and storage

10. MAINTENANCE AND STORAGE

Maintaining the machine

Before every use:

– Check that all nuts and bolts are tightened.

– Check that no fuel is leaking from the fuel tank.

– Lubricate the gearbox with grease.

After every 20 hours of operation (For this purpose we recommend you contact an authorised service

centre):

– Clean the air ﬁ lter.

– Clean the fuel ﬁ lter.

After every 50 hours of operation (For this purpose we recommend you contact an authorised service

centre):

– Clean the spark plug and adjust the gap between the electrodes to a distance of 0.6–0.7 mm.

– Clean out deposits from the exhaust and mufﬂ er.

– Disconnect the shaft and lubricate with quality lubricant.

Check the installation after performing maintenance and check that all nuts and bolts are pulled tight.

Service

In the event that after purchasing the product you ﬁ nd any kind of defect, contact the service department.

When using the product, follow the instructions contained in the included user’s manual.

A complaint will not be accepted if you modiﬁ ed the product or if you did not follow the instructions in the

user’s manual.

Warranty does not cover:

Normal wear and tear of operating parts of the machine as a result of its use

Servicing tasks related to standard maintenance of the machine (e.g. cleaning, lubrication, tuning, etc.)

Defects caused by external effects (e.g. climatic conditions, dustiness, inappropriate use, etc.)

Mechanical damage resulting from the machine being dropped, impact, etc.

Damages resulting from unprofessional handling, overloading, use of incorrect parts, inappropriate tools,

etc. On returned products that were not properly protected against mechanical damage during transport,

the risk of potential damage is borne exclusively by the owner.

Storage

ATTENTION! If you will not be using the machine for an extended period of time, store it according to the

following instructions. This will extend the lifetime of the machine.

Fully drain fuel from the fuel tank and the carburettor. Close the choke and pull on the cord 3 to 5 times.

Screw out the spark plug and pour a small amount of motor oil into the socket. Gently pull the pull cord

2 to 3 times.

Use a clean cloth to clean the exterior surfaces. Store the machine in a clean dry location.

EN

PETROL BRUSH CUTTER USER'S MANUAL

19

What to do "when"...

11. WHAT TO DO “WHEN”...

The engine will not start Possible cause Remedy

1. Check the fuel. There is no fuel in the fuel tank or

carburettor.

Add fuel.

The fuel contains water.

Incorrect ratio of the fuel mix. Drain the fuel tank and carburettor.

Fill the fuel tank with new fuel.

2. Remove and check the

spark plug.

Faulty or dirty spark plug. Replace the spark plug

Incorrect gap between the electrodes.

The spark plug is too damp, in contact

with petrol (ﬂ ooded engine).

Slide the spark plug out and reinstall.

3. Take the motor to

a qualiﬁ ed service centre

or to the vendor.

Clogged fuel ﬁ lter, carburettor defect,

starting defect, clogged valves, etc.

Replace or repair the faulty parts.

Engine performance is

insufﬁ cient

Cause of the malfunction Correction

1. Check the air ﬁ lter. Dirty air ﬁ lter. Clean or replace the air ﬁ lter insert.

2. Check the fuel. The fuel contains water. Drain the fuel tank and carburettor.

Fill the fuel tank with new fuel.

Incorrect ratio of the fuel mix.

3. Check the choke setting

and the throttle controls.

The throttle is not fully open. Adjust the setting.

Poorly adjusted throttle cable.

4. Take the motor to

a qualiﬁ ed service centre

or to the vendor.

Clogged fuel ﬁ lter, carburettor defect,

starting defect, clogged valves, etc.

Replace or repair the faulty parts.

EN 20

FZS 3005 B

What to do "when"...

The motor starts

and dies immediately

Possible cause Remedy

1. Check the fuel. Fuel ran out. Add fuel.

The fuel contains water. Drain the fuel tank and carburettor.

Fill the fuel tank with new fuel.

Incorrect ratio of the fuel mix.

2. Remove and check the

spark plug.

Faulty or dirty spark plug. Replace the spark plug.

Incorrect gap between the electrodes.

3. Check the air ﬁ lter. Dirty the air ﬁ lter. Clogged air ﬁ lter. Clean or replace the air ﬁ lter insert.

4. Take the motor to

a qualiﬁ ed service centre

or to the vendor.

Clogged air bleed valve. Replace or repair the faulty parts.

Clogged fuel ﬁ lter, carburettor defect,

starting defect, clogged valves, etc.

Strona jest ładowana ...

Fieldmann FZS 3005-B Instrukcja obsługi

Fieldmann FZS 3005-B Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty