Bissell Cleanview Lift-off 10N4 SERIES Instrukcja obsługi

Kategoria
Odkurzacze parowe
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

2
Thank You
USER'S GUIDE
10N4, 22K7 SERIES 220-240V
Safety Instructions
Product View
Assembly
Operations
Maintenance and Care
Troubleshooting
Accessories
Consumer Services
3
4-5
6
7-12
13-15
16
17
20
Replacement Parts
Warranty
18
19
www.bissell.com
Thanks for buying a BISSELL CleanView® Lift-Of
We’re glad you purchased a BISSELL CleanView
®
Lift-Off
®
.
Everything we know about floor care went into the innovative
design and construction of this complete, high-tech home cleaning
system.
Your BISSELL CleanView
®
Lift-Off
®
is well made, and we back it
with a limited five year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services department, so,
should you ever have a problem, you’ll receive fast, considerate
assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and
service of high quality homecare products like your BISSELL
CleanView
®
Lift-Off
®
.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman, President & CEO
2
www.bissell.com
IMPORTANT SAFETY INSTRUCTIONS
3
When using an electrical
appliance,
basic precautions should be observed,
including the following:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
DEEP CLEANER.
Always connect to a properly Earthed
outlet. Unplug from outlet when not in use
and before conducting maintenance or
troubleshooting.
WARNING: To
reduce the risk of fire,
electric shock, or injury:
Use indoors only
Do not immerse; use only on surfaces
moistened by cleaning process
Do not leave machine when it is plugged in
Do not service machine when it is plugged in
If the supply cord is damaged, it must
be replaced by the manufacturer or its
service agent in order to avoid a hazard
Do not use machine if it has been
dropped, damaged, left outdoors or
dropped into water
Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces
Do not carry the appliance while in use
Do not unplug by pulling on cord;
unplug by grasping plug not the cord
Do not handle plug or appliance with
wet hands
Do not put any object into appliance openings,
use with blocked opening or restrict air flow
Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts
Do not pick up hot or burning objects
Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene,
etc.) or use in the presence of explosive
liquids or vapours
Do not use appliance in an enclosed space
filled with vapours given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapours
Remove plug from electrical outlet before
cleaning or maintaining the appliance
Not intended for use by persons (including
children) with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been
given supervision or instruction concerning
use of the appliance by a person respon-
sible for their safety
Young children should be supervised to ensure
that they do not play with the appliance
Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, petrol, etc.)
Do not modify the Earthed plug
Do not use for any purpose other than
described in this User’s Guide
Use only manufacturer’s recommended
attachments
Use only cleaning products formulated
by BISSELL for use in this appliance to
prevent internal component damage
Keep openings free of dust, lint, hair, etc.
Keep appliance on a level surface
Turn off all controls before unplugging
Be extra careful when cleaning stairs
Pay close attention when working
around children
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
This model is for household use only.
WARNING:
This appliance must be Earthed
.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT
A.C. 50/60 Hz POWER SUPPLY ONLY.
If your appliance is fitted with a
nonrewireable BS 1363 plug it must not be
used unless a 13 amp (ASTA approved to BS
1362) fuse is fitted in the carrier contained
in the plug. (Spares may be obtained from
your BISSELL supplier). If for any reason the
plug is cut off, it must be disposed of, as it is
an electric shock hazard should it be inserted
into a 13 amp socket.
Dirty Tank
www.bissell.com
4
Power Cord
Heat
Indicator Light
Carry Handle
Upper Handle
Portable Spot
Cleaning Release
Pedal
Quick Release™
Cord Wrap
Formula &
Water Tank
Flex Hose
Removeable
Nozzle
Edge Sweep
Brushes
Product view
Power Button
www.bissell.com
Support Handle
Tool Storage
(select models)
Hose Secure
Latch
Tool Storage
Cord Clip
Recline Pedal
Product view
5
Cleaning formula
WARNING:
To reduce the risk of fire
and electric shock due
to internal component
damage, use only
BISSELL cleaning formulas
intended for use with the
deep cleaner.
Spray Trigger
Note: Additional BISSELL formula options may be available at your local retailer.
Keep plenty of genuine BISSELL 2X cleaning formula on hand so you can clean and protect
whenever it fits your schedule. Always use genuine BISSELL deep cleaning
formulas. Non-BISSELL cleaning formulas may harm the machine and will void the warranty.
651 mL
Tough
Stain
Precleaner
#0400-E
473 mL
2X Hard
Floor
Solutions
#56L9-E
1.5 L
2X Wash &
Protect Pet
Stain & Odour
Formula w/
Scotchgard
Protector
#66W9-E
1.5 L
2X Wash
& Protect
Professional
Formula w/
Scotchgard
Protector
#81L5-E
1.5 L
2X Wash &
Protect Fresh
Fragrance
Formula w/
Scotchgard
Protector
#92F4-E
1.5 L
2X Wash
& Protect
Spring Breeze
Fragrance
Formula w/
Scotchgard
Protector
#12W4-E
1.5 L
2X Wash
& Protect
Lavender
Fragrance
Formula w/
Scotchgard
Protector
#33D2-E
www.bissell.com
Assembly
6
Your CleanView
®
Lift-Off
®
comes in two
easy to assemble components:
1. Upper handle
2. Portable spot cleaner/Base
The only tool you will need to
assemble your cleaner is a Phillips
screwdriver.
1. Slide upper handle onto base
2. Screw the four included screws into the
marked holes.
Note: two of the holes are located
underneath the support handle indi-
cated by graphics. Angle screwdriver
to secure into place.
3. Wrap power cord around Quick Release
Cord Wrap.
4. Wrap flex hose around the hose wrap
and secure with hose secure latch.
5. Snap attachment(s) into the back of unit.
WARNING:
Do not plug in your
cleaner until you have
completely assembled it
per the above instructions
and are familiar with all
instructions and operat-
ing procedures.
1.
2.
1. 2.
Screw Holes
www.bissell.com
7
Operations
Special features
Innovative cleaning technology
This innovative deep cleaner offers two
machines in one. The upright deep cleaner
uses the power of heat, brushes and clean-
ing formula to get deep down dirt for a
maximum clean. The portable spot cleaner
detaches to clean tough spots and stains and
hard to reach areas.
Hot water heater
This deep cleaner features a patented
built-in hot water heater which will heat
the hand hot tap water you put in to safely
optimize cleaning effectiveness. The heater
temperature is limited to prevent carpet
damage. The heater automatically turns
on when you turn the machine on. This
operates only in upright cleaning mode.
Scotchgard™ Protector
Carpet protection applied at the mill typically
wears down over time from heavy foot traffic
and everyday cleaning, including deep clean-
ing. To help restore this important protection,
only BISSELL offers deep cleaning formulas
with Scotchgard protector. This offers extra
protection against dirt and tough stains to
keep your carpets looking good longer.
Microban
®
antibacterial protection
Microban antibacterial protection helps
prevent the growth of harmful common
household bacteria including E. coli,
Salmonella and Staph. a. It helps to keep
the unit fresher and cleaner between uses.
Pedal Graphic
Tip:
For easy carrying, grab the
carry handle portable spot
cleaner and balance with the
handle on the back of the
machine.
www.bissell.com
Operations
8
Before you clean
1. Move furniture to another area if cleaning
an entire room (optional).
2. Vacuum area with a dry vacuum cleaner
thoroughly before deep cleaning.
3. Pretreating (optional):
3a. Pretreating is recommended to improve
cleaning effectiveness for heavily soiled
carpet in high traffic areas such as
entryway and hallways.
3b. BISSELL Tough Stain precleaner
Spray the BISSELL Tough Stain
precleaner formula onto heavy traffic
areas, soiled areas or stains.
Allow to penetrate for at least 3 minutes.
Clean as normal, using the deep
cleaner in upright mode, following the
instructions below.
Upright cleaning mode
Filling formula & water tank
1. Remove tank from the base of the machine
by lifting up tank carry handle.
Note: This tank was designed with a flat
bottom so it can be easily filled.
2. Unscrew the black cap and remove bottle
insert.
3. Fill tank with hand hot tap water to the
water fill line. Add 60 mL of BISSELL 2X
formula to the tank.
4. Replace the bottle insert in the tank and
tighten the black cap. Replace the tank on
the deep cleaner.
Cleaning
1. Plug into a proper outlet and press the
power button. Allow 1 minute for the hot
water heater to warm-up before cleaning.
2. While pressing the spray trigger, make one
slow forward wet pass and another one back.
ATTENTION:
Some Berber carpets have a ten-
dency to fuzz with wear. Repeated
strokes in the same area with an
ordinary vacuum or deep cleaner
may aggravate this condition.
1.
3b.
2.
WARNING:
To reduce the risk of fire, use only
BISSELL deep cleaning formula for
full size machines in your deep
cleaner. Use of cleaning formulas
that contain lemon or pine oil may
damage this appliance and void the
warranty. Chemical spot cleaners or
solvent-based soil removers should
not be used. These products may
react with the plastic materials used in
your deep cleaner causing cracking
or pitting.
www.bissell.com
9
Operations
Cleaning continued
3. Release the spray trigger and make one
slow forward and backward pass over the
same area. Repeated passes will help aid
in dry time.
4. Continue passes until cleaning area is
complete.
Note: Your machine may be equipped
with a circuit breaker that will auto-
matically shut off the brush if a large
or loose object is caught in the brush
roll. If that happens, be sure to unplug
your machine, remove the foreign
object, and then plug the machine
back in to reset the circuit breaker.
Empty dirty tank
1. When the dirty tank reaches the
“FULL” line on the tank it is time to
empty.
2. Remove dirty tank and carry to a utility
sink, toilet or outside (where you will
dispose of the dirty water).
3. To unlock the dirty tank lid, rotate han-
dle over the back of the tank. Remove
lid and pour out dirty water. Rinse out
dirty tank to remove any debris.
4. Replace top of tank, and rotate the
handle forward to lock in place on front
of tank.
Cleaning your machine
1. Flush out machine of any remaining
residual solution.
Fill the formula & water tank with
hand hot tap water and turn on your
machine.
Recline handle and press the spray trig-
ger for about 15 seconds while making
forward and backward passes on car-
pet. Continue without pressing the spray
trigger until there is no more water
being suctioned up.
Turn off the machine and wrap the power
cord. Make sure the dirty tank and the
formula & water tank are emptied, rinsed,
and dried before the next use.
Before you replace tank, clean all
debris from red filter screen.
Upright cleaning mode continued
CAUTION:
Do not overwet. Take care not
to run over loose objects or
edges of area rugs. Stalling
brush may result in premature
belt failure.
Tip:
Make only one trip to the sink
by removing the entire por-
table cleaner. Fill and empty
in the same trip.
2.
3. 4.
Tip:
For best results empty,
rinse and dry both tanks
before storing.
WARNING:
To reduce the risk of fire, electric
shock, or injury, turn power
OFF and disconnect plug from
electrical outlet before performing
maintenance or troubleshooting.
www.bissell.com
Operations
10
Cleaning your machine continued
2. Rinse front nozzle of any dirt and debris.
Remove portable spot cleaner from the
base of the machine.
Unscrew three screws with Phillips screw
driver and remove nozzle.
Rinse nozzle out at the faucet.
Place back onto the machine by hooking
the tabs into the holes on the bottom sides
of the machine. Secure with screws.
3. The inside of the end caps can be
wiped out with a clean paper towel,
or for a more thorough clean, the end
caps can be taken off and rinsed clean.
4. Any loose hair or debris can be pulled
from the brush rolls and thrown away. For
a more thorough clean, follow directions
on page 15 for removal of brush rolls.
Your machine is now ready to be stored.
Note: Store cleaner in a protected,
dry area. Since this product uses
water, it must not be stored where
there is a danger of freezing.
Freezing will damage internal
components and void the warranty.
Upright cleaning mode continued
2.
WARNING:
To reduce the risk of fire, elec-
tric shock or injury unplug from
outlet before servicing.
Tip:
Let all parts dry completely
and replace onto machine.
www.bissell.com
11
Operations
Portable spot cleaning mode
Preparing the machine
1. Step on the portable spot cleaning pedal to
release the portable spot cleaner.
2. Release flex hose by twisting the hose
secure latch clockwise. Unwrap flex
hose completely.
3. Attach the desired tool to the hose grip
until it snaps together. Make certain the
tool is securely attached.
4. Twist the Quick Release cord wrap clock-
wise to unwrap the power cord com-
pletely and plug into grounded outlet.
Filling tank
1. Follow the instructions for filling the tank
in the upright cleaning mode section on
page 8
Cleaning with Tools:
IMPORTANT! If using to clean uphol-
stery, check upholstery tags. Check
manufacturers tag before cleaning.
“W” or “WS” on the tag means you
can use your CleanView
®
Lift-Off
®
if
the tag is coded with an “X” or an
“S”(with a diagonal stripe through it),
or says “Dry Clean Only”, do not pro-
ceed with any deep cleaning machine.
Do not use on velvet or silk. If manu-
facturers tag is missing or not coded,
check with your furniture dealer.”)
1. Hold the tool approximately 2.5 cm
above the soiled surface. Press the
spray trigger to apply the cleaning solu-
tion to the soiled area.
Note: Hold end of hose below the
tank water level to help prime the
portable spot cleaner.
2. Using the brush on the tool, gently scrub the
area to be cleaned.
3. Apply downward pressure on the tool and
pull it toward you. The suction will remove
the dirt and cleaning solution. Continue until
no more dirt can be removed.
Adsdfdd ghg bvh
cvbbj jkn hnbj jkvh
gcghhjj jhffhl kllgh
Manufacturer’s tag
IMPORTANT
Check for colourfastness in an
inconspicuous place. If pos-
sible, check upholstery stuffing.
Coloured stuffing may bleed
through fabric
www.bissell.com
Operations
12
Cleaning with Deep Reach™ Tool
(select models only)
1. Set tool on soiled surfaces and press the
spray trigger to spray solution onto the
soiled area to be cleaned.
2. Slowly move the tool back and forth over
the soiled surface, keeping the tool in con-
tact with the carpet.
Release spray trigger and move tool
slowly over the soiled area to suction up
water and dirt.
4. Continue to clean the area, working in
small sections, until no more dirt can be
removed.
Empty dirty tank
Follow the instructions under Empty
dirty tank section on page 9 of the
Upright cleaning mode section.
Replacing portable machine on base
1. Align the product as the graphic shows,
with the cord side on the left and hose
side on the right.
2. Push down the portable spot cleaner
until you hear it click securely into
place. Test the fit by pulling up on the
carry handle to make sure it is secure.
Cleaning portable machine
1. Remove and rinse the tools in clean, run-
ning water. Dry and replace in the tool
storage provided.
2. It is recommended that you suction clean
water from a bowl to rinse out the hose.
Then lift end of hose and stretch out to
ensure all water is cleared from hose.
3. Coil flex hose around the hose wrap
and secure with latch.
4. Check suction gate and if it appears
dirty, follow steps 1-4 under Cleaning
Suction Gate on page 13.
1.
3.
Portable spot cleaning mode continued
Graphic
1.
www.bissell.com www.bissell.com
13
Maintenance and care
Machine care (check regularly)
Cleaning suction gate
The suction gate automatically diverts
air when the portable deep cleaner
is detached. This should be checked
and cleaned regularly for any dirt and
debris.
1. Step on the pedal and remove the
portable spot cleaner. Remove dirty
tank.
2. Remove two screws and pull off
suction gate door.
3. Wipe suction gate clean and rinse
suction gate door.
4. Replace suction gate door and two
screws.
Cleaning spray tips
1. Step on the pedal and remove the
portable spot cleaner. To remove, push
in tab and pull it out.
2. Clean by rinsing under water.
3. Replace by snapping back in.
4. Repeat steps on second spray tip.
Cleaning solution filter
1. Step on the pedal and remove the
portable spot cleaner. Remove the red
solution filter cap on the base of the
machine by inserting a coin or a flat
head screw driver into the slot on the
top.
2. Turn counter clockwise to unscrew. Set
aside.
3. Remove the white filter by the post.
Rinse the filter under water.
4. Replace the white filter back into the
filter area.
Note: Make sure the white filter
is seated properly before replac-
ing the red solution filter cap.
5. Replace the red solution filter cap and
turn clockwise to tighten.
Solution
Filter Cap
Suction
Gate
Filter
2.
3.
5.
Spray
Tips
1.
2.
WARNING:
To reduce the risk of fire, elec-
tric shock, or injury, turn power
OFF and disconnect plug from
electrical outlet before perform-
ing maintenance or trouble-
shooting.
www.bissell.com
Maintenance and care
14
Occasional replacement of one or
both belts may become necessary.
If that is needed, please follow the
instructions below.
1. Turn off the machine, and unplug it from
the outlet. Remove portable spot cleaner.
2. Remove the nozzle by unscrewing three
screws on the nozzle cover.
3. Turn the machine on its side.
IMPORTANT: with portable spot
cleaning pedal facing down.
4. Remove end cap by unscrewing the
3 screws. Take care not to drop the
screws into the unit.
5. Remove 1 silver screw from the pivot
arm.
6. Remove pivot arm by gently lifting up.
7. Remove small brush belt.
8. Replace small brush belt, and reverse
steps above.
9. Manually rotate brushes by hand to make
sure they move freely. May notice a slight
resistance from the motor.
2.
4.
6.
8.
Small belt removal and replacement (as needed)
7.
5.
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
www.bissell.com
15
Maintenance and care
Brushes can be removed for cleaning
or replacement as needed.
1. Follow small belt removal Instructions on
page 14 items 1-7.
2. Remove brush rolls by pulling them off
of the metal rods. Be careful not to
lose the small washer at each
end of the brush rolls.
3. Re-attach the large belt to the grooves
on the end of the new brush rolls. If the
belt is damaged, replace with a new
belt.
4. Place cleaned or new brush rolls back
onto the rods. Make sure one washer is
on each end of the rollers prior to sliding
onto the rod. Be sure the brush is seated
completely on the rod.
5. Replace small belt over grooves in back
roller and metal cog.
6. Replace pivot arm and secure with silver
screw.
7. Re-attach end cap by tightening with the
(3) black screws.
8. Return front nozzle to front of unit, by
latching from underneath and then
securing with 3 screws.
9. Follow step number 8 & 9 on page 14.
If you have any questions or are having
trouble installing or replacing your
belt(s) or brushes, please call
BISSELL Consumer Services.
2.
4.
6.
8.
3.
5.
7.
Brush removal and large belt replacement (as needed)
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
www.bissell.com
Troubleshooting
16
Built-in heater ready light does not illuminate
Possible causes Remedies
1. The power is not turned ON 1. The power must be ON to activate the heater ready light
2. The portable spot cleaner is not attached completely 2. Make sure the portable spot cleaner is attached
Push down firmly to check
Reduced Spray or No Spray
Possible causes Remedies
1. Formula & water tank may be empty 1. Refill tank
2. Formula & water tank may not be seated completely 2. Turn power OFF. Remove and reseat tank
3. Pump may have lost prime in portable spot cleaning mode 3. Hold end of hose below water level in tank to prime
4. The portable spot cleaner is not attached completely 4. Push down firmly to check connection
5. Solution filter may be clogged 5. Follow steps under cleaning filter on page 13
DirtLifter
PowerBrush does not turn
Possible causes Remedies
1. The portable spot cleaner is not attached completely 1. Make sure the portable spot cleaner is attached.
Push down firmly to check
2. The unit is in the upright position 2. Brushes only rotate when unit is reclined using the
recline pedal
3.
Circuit breaker on machine (if equipped) may have tripped
3. Turn the machine OFF and unplug from outlet. Check
to see if foreign object is caught in brush roll. Remove
object. Plug machine in to reset circuit breaker
4. The belt is off or broken 4. Turn power OFF and unplug unit from outlet. Follow
instructions on pages 14 and 15
Loss of suction power
Possible causes Remedies
1. Tanks may not be seated properly 1. Pick up both tanks and reseat them so it they fit snugly on
the unit
2. Nozzles may not be assembled properly 2. Unplug the unit. Check to make sure the "lip" of the
nozzle is securely hooked into the groove on bottom of
Tank (see page 10)
3. The portable spot cleaner is not attached completely 3. Make sure the portable spot cleaner is attached.
Push down firmly to check
4. Dirty tank has picked up maximum amount of 4. Empty dirty tank
dirty water and has reached full line
5. Formula & water tank is empty 5. Check fluid levels in formula & water tank
6. Suction gate is open 6. Check to make sure the suction gate is closed. Follow
“Cleaning suction gate” instructions on page 13
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
www.bissell.com
17
Accessories & formulas
Item Part No. Part Name
1 203-6651 3” Tough Stain Tool
2 203-6652 Powered TurboBrush™ Hand Tool
3 203-6653 4” Upholstery Tool
4 203-6654 6” Stair Tool
5 203-7885 Spraying Crevice Tool
6 203-8113 Deep Reach™ Tool
7 310-3040 Mesh Bag
8 81L5-E 1.5 L 2X Wash & Protect Professional Formula w/ Scotchgard
Protector
9 66W9-E 1.5 L 2X Wash & Protect Pet Stain & Odour Formula w/ Scotchgard
Protector
10 92F4-E 1.5 L 2X Wash & Protect Fresh Fragrance Formula w/ Scotchgard
Protector
11 12W4-E 1.5 L 2X Wash & Protect Spring Breeze Fragrance Formula w/
Scotchgard
Protector
12 33D2-E 1.5 L 2X Wash & Protect Lavender Fragrance Formula w/ Scotchgard
Protector
13 0400-E 651 mL Tough Stain Precleaner
*Not all parts are included with every model.
1
6
13
2 3 4 5
11
7 8
12
9 10
Note: Additional BISSELL formula options may be available at your local retailer.
Below please find a list of common replacement parts. While not all of these
parts may have come with your specific machine, all are available to you for
purchase, if desired.
Item Part No. Part Name
1 203-7893 Formula & Water Tank Assembly (includes cap and insert)
2. 203-6675 Cap and Insert for Formula & Water Tank
3. 203-8102 Dirty Tank Assembly (includes entire tank)
4. 203-7904 Cord Wrap
5. 203-7896 End Caps with Edge Brushes (2 pack, includes screws)
6. 203-7897 Spray Tips Assembly (includes two spray tips)
7. 203-7898 In-line Filter Assembly (includes cap and filter)
8. 203-7901 Nozzle Gasket
9. 203-8103 Nozzle Cover Assembly (includes gasket, nozzle cover, and front nozzle cover)
10. 203-8104 Front Nozzle
11. 203-8105 Brush Assembly (includes 2 brush rolls, 2 axles, and 2 swivel arms)
12. 203-8106 Brush Single Pack (includes 1 brush roll, and 1 axle)
13. 203-7900 Small Brush Belt
14. 203-7899 Large Brush Belt
15. 203-6689 Hose Secure Latch
16. 203-7918 Dirty Tank Gasket Assembly (include both gaskets)
17. 203-7917 Diverter Cover Assembly (includes cover and screws)
*Not all parts are included with every model.
www.bissell.com
18
Replacement parts
1
6
11
16
2
7
12
17
3
8
13
4
9
14
5
10
15
www.bissell.com
19
Warranty - BISSELL CleanView® Lift-Off®
This warranty gives you specific legal rights, and you may also have other rights which may
vary from country to country. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by
telephone, or regular post as described below, or contact your local in country distributor.
Limited Five Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc.,
will replace (with new or remanufactured components), at BISSELLs option, free of charge
from the date of purchase by the original purchaser, for five years any defective or
malfunctioning part do to manufacturers defect.
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, or use not in accordance with
the User’s Guide is not covered.
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO THE FIVE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire SL1 4QT
United Kingdom
Telephone: 0844-888-6644
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
BISSELL consumer services
©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4421
Rev 10/11
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban
®
is a registered trademark
of Microban Products Company
www.bissell.com
20
If your BISSELL product should require service:
Call BISSELL Consumer Services at the numbers below and we will give you the location of a
BISSELL Authorized Service Center in your area. If you have questions about your warranty or
need replacement parts please contact the numbers below.
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It
provides proof of purchase date in the event of a
warranty claim. See Warranty on page 19 for details.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire SL1 4QT
United Kingdom
Telephone: 0844-888-6644
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Bissell Cleanview Lift-off 10N4 SERIES Instrukcja obsługi

Kategoria
Odkurzacze parowe
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla