Tenda Desktop Switch Instrukcja instalacji

Kategoria
Przełączniki sieciowe
Typ
Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

Quick Installation Guide
9-Port 10/100M Ethernet Desktop Switch
8FE+1GE Desktop Switch
TEF1109D/TEF1109DT
Package contents
· Switch * 1
· Power adapter * 1
· Quick installation guide * 1
Connect your devices
Power
LAN1 LAN2 LAN3 LAN4 WAN
VLAN
on
Grounding terminal
Internet
Router
IP camera
Computer
Printer
Port 9
LAN port WAN port
Tip:
All ports of your switch support the auto MDI/MDIX function, indicating that either straight cable or crossover cable is acceptable
to connect your switch to Ethernet devices.
To protect your switch from lightning damage, connect the grounding terminal of the switch to a grounding cable.
Model
TEF1109D
TEF1109DT
Standards
IEEE 802.3, IEEE 802.3u,
IEEE 802.3x
IEEE 802.3, IEEE 802.3u,
IEEE 802.3x,
IEEE 802.3ab
10/100 Mbps RJ45 Port
Port 1 - 9
Port 1 - 8
10/100/1000 Mbps RJ45 Port
/
Port 9
Working mode
VLAN off, VLAN on
Switching capacity
1.8 Gbps
3.6 Gbps
Store-and-forward
Supported
Auto learning & auto aging
Supported
MAC address table
2 K
Dimension
140.2 mm * 66.2 mm * 25.2 mm
Power supply
Input: 100-240 V AC, 50/60 Hz, 0.3 A
Output: 9 V DC, 0.6 A
Lightning protection
6 kV for port 9
Operating environment
Temperature: (0 - 40) °C
Humidity: (10 - 90) % RH, non-condensing
Storage environment
Temperature: (-40 - 70) °C
Humidity: (5 - 90) % RH, non-condensing
Transmission rate
Ethernet: 10 Mbps (half duplex) / 20 Mbps
(full duplex)
Fast Ethernet: 100 Mbps (half duplex) / 200
Mbps (full duplex)
/
Gigabit Ethernet:
2000 Mbps (full
duplex)
Transmission media
Ethernet: CAT3 UTP/STP cable or better
Fast Ethernet: CAT5 UTP/STP cable or better
/
Gigabit Ethernet: CAT5e
or CAT6 UTP/STP cable
(recommended)
Specifications
LED indicator
Status
Description
Solid on
The switch is connected to a
power resource properly.
Off
The switch is disconnected or not
properly connected to a power
resource.
1-9
Solid on
The port is connected properly.
Blinking
Data is being transmitted over the
port.
Off
The port is disconnected or
improperly connected.
LED indicators
Working mode introduction
The switch has two modes: VLAN off and VLAN on. Use the
slide switch to set the switch to your required mode
according to the following descriptions.
VLAN off: Default mode of the switch. In this mode, all ports
can communicate with each other.
VLAN on: In this mode, ports 1 to 8 of TEF1109D/TEF1109DT
can communicate with port 9 but cannot communicate with
each other. You can enable this mode to reduce broadcast
storm and isolate DHCP broadcast.
English
LED-Anzeige
Status
Leuchtet
Aus
1-9
Leuchtet
Blinkt
Aus
LED-Anzeige
Einführung in die Betriebsmodi
Der Switch hat zwei Modi: VLAN off und VLAN on. Schalten
Sie den Switch über den Schieberegler in den gewünschten
Modus. Wählen Sie den Modus geß der nachfolgenden
Beschreibungen aus.
VLAN off: Ist der Standardmodus des Switches. In diesem
Modus können alle Ports des Switches untereinander
kommunizieren.
VLAN on: In diesem Modus können die Ports 1 bis 8 des
TEF1109D/TEF1109DT mit dem Port 9 kommunizieren aber
nicht untereinander. Verwenden Sie diesen Modus, um
Broadcast-Storm zu reduzieren oder den DHCP-Broadcast
zu isolieren.
Deutsch
Indicateur LED
Statut
Description
Solide en
marche
Le dispositif est branché
correctement à l'alimentation.
Eteint
Le commutateur est déconnecté de la
source d’alimentation ou n’est pas
connecté à une source d’alimentation.
1-9
Solide en
marche
Le port est correctement connecté.
Clignotant
Les données sont transmises à travers
le port.
Eteint
Le port est déconnecté ou n’est pas
correctement connecté.
Indicateurs LED
Introduction du mode de
fonctionnement
Le commutateur a deux modes: VLAN off, et VLAN on.
Utilisez la glissière pour régler le commutateur au mode
requis selon les descriptions suivantes.
VLAN off: Mode par défaut du commutateur. Dans ce mode,
tous les ports du commutateur pourraient communiquer
entre eux.
VLAN on: Dans ce mode, les ports 1 à 8 de
TEF1109D/TEF1109DT peuvent communiquer avec le port9
mais pas entre eux. Vous pouvez activer ce mode pour
réduire la diffusion et isoler la diffusion DHCP.
Français
Indicador LED
Estado
Descripción
Encendido
El dispositivo está conectado a la
fuente de alimentación
correctamente.
Apagado
El switch está desconectado o no
correctamente conectado a una
fuente de alimentación.
1-9
Encendido
El puerto está conectado
correctamente.
Parpadeo
Se están transmitiendo datos sobre el
puerto.
Apagado
El puerto está desconectado o mal
conectado.
Indicadores LED
Introducción al Modo Trabajo
El switch dispone de dos modos: VLAN off y VLAN on. Use el
interruptor para establecer el switch en el modo requerido
de acuerdo con las descripciones siguientes.
VLAN off: modo predeterminado del switch. En este modo,
todos los puertos del conmutador pueden comunicarse
entre sí.
VLAN on: En este modo, los puertos 1 a 8 del
TEF1109D/TEF1109DT pueden comunicarse con el puerto 9
pero no pueden comunicarse entre sí. Puede usar este
modo para reducir la tormenta de difusión y aislar la
transmisión DHCP.
Español
Indicador LED
Estado
Descrição
Sólido
ativado
O dispositivo está ligado à fonte de
alimentação adequada.
Off
(Desligado)
O interruptor é desligado da fonte de
alimentação ou não é conectado a
uma fonte de alimentação.
1-9
Sólido
ativado
A porta está ligada corretamente.
A piscar
Os dados estão a ser transmitidos
pela porta.
Off
(Desligado)
A porta está desconectada ou
indevidamente conectada.
Indicadores LED
Introdução ao Modo de Trabalho
O interruptor tem dois modos: VLAN off e VLAN on. Use o
controlo deslizante para definir o interruptor para o modo
necesrio de acordo com as seguintes descrições.
VLAN off: Modo padrão do interruptor. Neste modo, todas
as portas do switch podem se comunicar entre si.
VLAN on: Neste modo, as portas 1 a 8 do
TEF1109D/TEF1109DT podem comunicar com a porta 9 mas
o podem comunicar entre si. Pode utilizar este modo para
reduzir os disrbios de transmissão e isolar a transmissão
DHCP.
Português
Indicatore LED
Stato
Descrizione
Accensione
fissa
Il dispositivo è collegato alla rete
elettrica correttamente.
Spento
L'interruttore è scollegato
dall'alimentazione o non
correttamente collegato a una presa
di corrente.
1-9
Accensione
fissa
La porta è collegata correttamente.
Accensione
intermittente
I dati vengono trasmessi attraverso
la porta.
Spento
La porta è scollegata o collegata in
modo non corretto.
Indicatori LED
Introduzione modalità di lavoro
Lo switch presenta due modalità: VLAN off, e VLAN on.
Utilizzare l'interruttore scorrevole per regolare l'interruttore
nella modalità richiesta secondo le seguenti indicazioni.
VLAN off: Modalità predefinita dell'interruttore. In questa
modalità tutte le porte dello switch possono comunicare tra
loro.
VLAN on: In questa modalità, le porte 1 - 8 del
TEF1109D/TEF1109DT possono comunicare con la porta 9
ma non tra di loro. Si può utilizzare questa modalità per
ridurre il broadcast storm e isolare la trasmissione DHCP.
Italiano
LED visszajelző
Státusz
Leírás
Folyamatosan
bekapcsolva
A készülék helyesen van az
energiaellátáshoz csatlakoztatva.
kikapcsolva
A váltó nincs, vagy nem
megfelelően van csatlakoztatva a
tápegységhez.
1-9
Folyamatosan
bekapcsolva
Az egyező port helyesen van
csatlakoztatva.
Villog
Adatátvitel van folyamatban a
porton keresztül.
kikapcsolva
A port nincs, vagy nem
megfelelően van csatlakoztatva.
LED-jelzők
Bevezetés: üzemmódok
A kapcsoló két üzemmóddal rendelkezik: VLAN off (VLAN
kikapcsolva) és VLAN on (VLAN bekapcsolva). A
csúszókapcsolóval állítsa a kapcsolót a kívánt üzemdba
az alábbi lrások szerint.
VLAN off: A kapcsoló alapértelmezett üzemmódja. Ebben a
dban a váltó összes portja tud kommunikálni egymással.
VLAN on: Ebben az üzemmódban a TEF1109D/TEF1109DT
1–8-es portja képes kommunikálni az 9-ös porttal, de nem
pesek kommunikálni egymással. Ezzel az üzemmóddal
csökkentheti a szósi viharokat, és elkülötheti a
DHCP-srást.
Magyar
LED индикатор
Статус
Описание
Без
прекъсване
Превключвателятесвързан
правилноселектрозахранването.
Изключен
(Off)
Прекъсвачътеизключенот
захранванетоилинеесвързан
правилноснего.
1-9
Без
прекъсване
Портътесвързанправилно.
Мигащ
Даннитесепредаватпрезпорта.
Изключен
(Off)
Портътепрекъснатили
неправилносвързан.
LED индикатори
Въведениевработниярежим
Превключвателятимадварежима:VLANoff(VLAN
изключено)иVLANon(VLANвключено).Използвайте
страничнияпревключвател,заданастроите
превключвателявизискваниярежимспоредследните
описания.
VLANoff:Режимпоподразбираненапревключвателя.
Втозирежимвсичкипортовемогатдакомуникират
единсдруг.
VLANon:Втозирежимпортовеот1до8от
TEF1109D/TEF1109DTмогатдакомуникиратспорт9,но
немогатдакомуникиратединсдруг.Можетеда
използватетозирежим,заданамалитебродкаст
бурятаидаизолиратеизлъчванетонаDHCP.
Български
Kontrolka LED
Stan
Opis
Ciągłe
światło
Urządzenie jest prawidłowo
podłączone do źródła zasilania.
Wyłączone
Urządzenie jest odłączone od źródła
zasilania lub nie zostało do niego
poprawnie podłączone.
1-9
Ciągłe
światło
Gniazdo jest połączone poprawnie.
Miganie
Port obsługuje przesyłanie danych.
Wyłączone
Port jest odłączony lub niepoprawnie
podłączony.
Kontrolki LED
Wprowadzenie do trybów pracy
Switch może dziać w dwóch trybach: VLAN off. i VLAN on.
Za pomocą przełącznika włącz w switchu wymagany tryb
pracy. Opisy trybów znajdują się poniżej.
VLAN off: Tryb domyślny switcha. W tym trybie wszystkie
porty switcha mogą się ze sobą komunikować.
VLAN on: W tym trybie porty od 1 do 8 urdzenia
TEF1109D/TEF1109DT mogą komunikować się z portem 9,
ale nie ze sobą nawzajem. Dzięki temu trybowi można
zmniejszyć liczbę burz broadcastowych i odizolow
rozgłaszanie DHCP.
Polski
Indicator LED
Stare
Descriere
Rămâne
aprins
Dispozitivul este conectat corect la
sursa de alimentare.
Oprit
Switch-ul este deconectat de la sursa
de alimentare sau nu este conectat
corect la sursa de alimentare.
1-9
Rămâne
aprins
Portul corespunzător este conectat
corect.
Lumineaza
intermitent
Datele sunt transmise prin port.
Oprit
Portul este deconectat sau nu este
conectat corect.
Indicatoare LED
Prezentarea modurilor de lucru
Switch-ul are două moduri: VLAN off şi VLAN on. Setati
switch-ul în modul dorit din comutator, conform
următoarelor descrieri.
VLAN off: Modul implicit al switch-ului. În acest mod, toate
porturile pot comunica între ele.
VLAN on: În acest mod, porturile 1 - 8 ale
TEF1109D/TEF1109DT pot comunica cu portul 9 dar nu pot
comunica între ele. Puteți utiliza acest mod pentru a reduce
broadcast storm și pentru a izola DHCP broadcast.
Română
Светодиодный
индикатор
Статус
Описание
Коммутаторподключенк
источникупитания.
Негорит
Коммутаторотключенот
источникапитанияили
подключенкнемунеправильно.
1-9
Портподключенправильно.
Мигает
Черезпортосуществляется
передачаданных.
Негорит
Портнеподключенилиподключн
неправильно.
Светодиодныеиндикаторы
Обзоррежимовработы
Укоммутатораестьдварежима:VLANoffиVLAN
on.Используйтепереключательдляперевода
коммутаторавнужныйрежим,выбранныйна
основеописания.
VLANoff:Режимкоммутаторапоумолчанию.В
этомрежимевсепортымогутподключатьсядругк
другуиимеютодинаковыйприоритет.
VLANon:Вэтомрежимепорты1‒8устройства
TEF1109D/TEF1109DTмогутподключатьсяк
порту9,нонемогутподключатьсядругкдругу.В
этотрежимможноперейти,чтобыуменьшить
broadcastштормиизолироватьDHCPbroadcast.
Русский
Горит
постоянно
Горит
постоянно
FCC Statement
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions:(1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Caution!
Anychanges or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. (2) To avoid unnecessary radiation interference, it is
recommended to use a shielded RJ45 cable.
Caution:
Adapter Model: BN049-A05009E/BN049-A05009B
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Input: 100 - 240 V AC 50/60 Hz, 0.3 A
Output: 9 V 600 mA
: DC Voltage
Producto
NOMBRE DEL PRODUCTO:
Switch de escritorio 8FE+1GE
MODELO: TEF1109DT
Alimentador de Energía:
Alimentación: 100-240 V ca 50/60 Hz, 0.3 A
Salida: 9 V cc 0.6 A
PAIS DE ORIGEN: CHINA
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
The mains plug is used as disconnect device; the disconnect device
shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. (2) To avoid unnecessary radiation interference, it is
recommended to use a shielded RJ45 cable.
This product bears the selective sorting symbol for Waste electrical
and electronic equipment (WEEE). This means that this product must
be handled pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or
electronic equipment.
RECYCLING
LA OPERACIóN DE ESTE DISPOSITIVO ESTA SUJETA A LAS
SIGUIENTES CONDICIONES:
a) Es posible que este equipo o dispositivo no cause
interferencia perjudicial.
b) Este equipo o dispositivo debe aceptar cualquier tipo de
interferencia, incluyendo la que pueda causar su operación no
deseada.
Producto
NOMBRE DEL PRODUCTO:
Switch de escritorio Ethernet de 9 puertos 10 / 100M
MODELO: TEF1109D
Alimentador de Energía:
Alimentación: 100-240 V ca 50/60 Hz, 0.3 A
Salida: 9 V cc 0.6 A
PAIS DE ORIGEN: CHINA
Copyright
Copyright © 2018 Shenzhen Tenda Technology Co., Ltd. All rights
reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda
Technology Co., Ltd. Other brand and product names mentioned
herein are trademarks or registered trademarks of their respective
holders. Specifications are subject to change without notice.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan
District, Shenzhen, China. 518052
Canada hotline: 1-888-998-8966
Hong Kong hotline: 00852-81931998
Website: http://www.tendacn.com
If any item is missing, damaged or incorrect, please keep the
original packaging and contact the local reseller or distributor
immediately.
Example: TEF1109D
  • Page 1 1

Tenda Desktop Switch Instrukcja instalacji

Kategoria
Przełączniki sieciowe
Typ
Instrukcja instalacji
Ten podręcznik jest również odpowiedni dla