Tenda TEF1109TP-8-102W Instrukcja instalacji

TEF1109TP-8-102W
Tenda
Marka
Tenda
Model
TEF1109TP-8-102W
Kategoria
Przełączniki sieciowe
Typ
Instrukcja instalacji
Model
TEF1109TP-8-102W
Standards
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at,
10/100Mbps RJ45 port
8
Working mode
VLAN Off, VLAN On
Switching capacity
3.6 Gbps
Store-and-forward
Supported
MAC address learning
Auto learning & auto aging
MAC address table
2 K
PoE power
supply
PoE standard
IEEE 802.3af, IEEE 802.3at
PoE port
1 - 8
Maximum output of a
single port
30 W
Maximum output of the
switch
92 W
PoE power cable core
8 cores: voltage of cores 1, 2, 4, 5 is +, and cores 3, 6, 7, 8 is -.
Lightning
protection
Port
6 kV (for port 9)
Power supply
Common mode: 4 kV
Differential mode: 4 kV
Environment
Operating environment
Temperature: (0 - 40) °C
Humidity: (10% - 90%) RH non-condensing
Storage environment
Temperature: (-40 - 70) °C
Humidity: (5% - 90%) RH, non-condensing
Power supply
Input: 100 - 240 V AC 50/60 Hz, 1.6 A
Output: 51 V DC 2 A
Dimension
177.5 mm * 104.1 mm * 26 mm
Transmission media
Ethernet: CAT3 UTP/STP cable or better
Fast Ethernet: CAT5 UTP/STP cable or better
Specifications
Copyright
Copyright © 2019 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd.
Other brand and product names mentioned herein are trademarks or registered trademarks
of their respective holders. Specifications are subject to change without notice.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052
Canada hotline: 1-888-998-8966
Toll free: Mon to Fri, 9am to 6pm PST
Hong Kong hotline: 00852-81931998
Global hotline: +86 755-2765 7180 (China time zone)
Website: http://www.tendacn.com
E-mail: [email protected]
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
The mains plug is used as disconnect device; the disconnect device shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is
recommended to use a shielded RJ45 cable.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is
recommended to use a shielded RJ45 cable.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
This means that this product must be handled pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the environment.
Producto
NOMBRE DEL PRODUCTO:
Switch de Escritorio de 8 puertos PoE 8FE+1GE
Alimentador de Energía:
Alimentación: 100 - 240 V ca 50/60 Hz, 1.6 A
PAIS DE ORIGEN: CHINA
LA OPERACIóN DE ESTE DISPOSITIVO ESTA SUJETA A LAS SIGUIENTES CONDICIONES:
a) Es posible que este equipo o dispositivo no cause interferencia perjudicial.
b) Este equipo o dispositivo debe aceptar cualquier tipo de interferencia, incluyendo la que
pueda causar su operación no deseada.
Caution:
Adapter Model: BN038-A10151
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Input: 100 - 240 V AC 50/60 Hz, 1.6 A
Output: 51 V 2 A
: DC Voltage
LED-Anzeige
Beschreibung
PWR
Das Gerät ist korrekt an eine Stromversorgung angeschlossen.
Der Switch ist von der Stromversorgung getrennt oder nicht
ordnungsgemäß angeschlossen.
Link/Act
Der Port ist korrekt verbunden.
Die Daten werden über den Port übertragen.
Der Port ist nicht verbunden oder falsch angeschlossen.
Einführung in die Betriebsmodi
Der PoE-Switch hat zwei Modi: VLAN Off und VLAN On. Schalten Sie den PoE-Switch
über den Schieberegler in den gewünschten Modus. Wählen Sie den Modus gemäß der
nachfolgenden Beschreibungen aus.
VLAN Off: Ist der Standardmodus des PoE-Switches. In diesem Modus können alle Ports
des Switches untereinander kommunizieren.
VLAN On: In diesem Modus können die Ports 1 bis 8 des TEF1109TP-8-102W mit dem
Port 9 kommunizieren aber nicht untereinander. Verwenden Sie diesen Modus, um
Broadcast-Storm zu reduzieren oder den DHCP-Broadcast zu isolieren.
Deutsch
Indicatore LED
Stato
Descrizione
PWR
Spento
L'interruttore è scollegato dall'alimentazione o non
Link/Act
Accensione
I dati vengono trasmessi attraverso la porta.
Spento
La porta è scollegata o collegata in modo non corretto.
Introduzione modalità di lavoro
Lo switch PoE presenta due modalità: VLAN Off, e VLAN On. Utilizzare l'interruttore
scorrevole per regolare l'interruttore PoE nella modalità richiesta secondo le seguenti
indicazioni.
VLAN Off: Modalità predefinita dell'interruttore PoE. In questa modalità tutte le porte
dello switch possono comunicare tra loro.
VLAN On: In questa modalità, le porte 1-8 del TEF1109TP-8-102W possono comunicare
con la porta 9 ma non tra di loro. Si può utilizzare questa modalità per ridurre il
broadcast storm e isolare la trasmissione DHCP.
Italiano
Indicador LED
Estado
Descrição
PWR
Off (Desligado)
O interruptor é desligado da fonte de alimentação ou não
Link/Act
Sólido ativado
A porta está ligada corretamente.
A piscar
Os dados estão a ser transmitidos pela porta.
Off (Desligado)
A porta está desconectada ou indevidamente conectada.
Introdução ao Modo de Trabalho
O interruptor PoE tem dois modos: VLAN Off e VLAN On. Use o controlo deslizante
para definir o interruptor PoE para o modo necessário de acordo com as seguintes
descrições.
VLAN Off: Modo padrão do interruptor PoE. Neste modo, todas as portas do switch
podem se comunicar entre si.
VLAN On: Neste modo, as portas 1 a 8 do TEF1109TP-8-102W podem comunicar com a
porta 9 mas não podem comunicar entre si. Pode utilizar este modo para reduzir os
Português
Indicador LED
Estado
Descripción
PWR
Encendido
El dispositivo está conectado a la fuente de alimentación
Apagado
El switch está desconectado de una fuente de alimentación o no
Link/Act
Introducción al Modo Trabajo
El switch PoE dispone de dos modos: VLAN Off y VLAN On. Use el interruptor para
establecer el switch PoE en el modo deseado de acuerdo con las descripciones
siguientes.
VLAN Off: modo predeterminado del switch PoE. En este modo, todos los puertos del
conmutador pueden comunicarse entre sí.
VLAN On: En este modo, los puertos 1 a 8 del TEF1109TP-8-102W pueden comunicarse
con el puerto 9 pero no pueden comunicarse entre sí. Puede usar este modo para
Español
Indicateur LED
Statut
Description
PWR
Solide en
Le dispositif est branché correctement à l'alimentation.
Eteint
Le commutateur est déconnecté de la source d’alimentation
ou n’est pas connecté à une source d’alimentation.
Link/Act
Solide en
Le port est correctement connecté.
Clignotant
Les données sont transmises à travers le port.
Eteint
Le port est déconnecté ou n’est pas correctement connecté.
Introduction du mode de fonctionnement
Le commutateur PoE a deux modes: VLAN Off, et VLAN On. Utilisez la glissière pour
régler le commutateur PoE au mode requis selon les descriptions suivantes.
VLAN Off: Mode par défaut du commutateur PoE. Dans ce mode, tous les ports du
commutateur pourraient communiquer entre eux.
VLAN On: Dans ce mode, les ports 1 à 8 de TEF1109TP-8-102W peuvent communiquer
avec le port 9 mais pas entre eux. Vous pouvez activer ce mode pour réduire la diffusion
et isoler la diffusion DHCP.
Français
LED индикатор
Статус
Описание
PWR
Без прекъсване
Превключвателят е свързан правилно с електрозахранването.
Изключен (Off)
Прекъсвачът е изключен от захранването или не е свързан
правилно с него.
Link/Act
Без прекъсване
Портът е свързан правилно.
Мигащ
Данните се предават през порта.
Изключен (Off)
Портът е прекъснат или неправилно свързан.
Въведение в работния режим
Превключвателят за захранване по Ethernet (PoE) има два режима: VLAN Off
(VLAN изключено) и VLAN On (VLAN включено). Използвайте страничния
превключвател, за да настроите превключвателя за захранване по Ethernet
(PoE) в изисквания режим според следните описания.
VLAN Off: Режим по подразбиране на превключвателя за захранване по
Ethernet (PoE). В този режим всички портове могат да комуникират един с друг.
VLAN On: В този режим портове от 1 до 8 от TEF1109TP-8-102W могат да
комуникират с порт 9, но не могат да комуникират един с друг. Можете да
използвате този режим, за да намалите бродкаст бурята и да изолирате
излъчването на DHCP.
Български
LED visszajelző
Státusz
Leírás
PWR
Folyamatosan
A készülék helyesen van az energiaellátáshoz csatlakoztatva.
Ki
A váltó nincs, vagy nem megfelelően van csatlakoztatva a
tápegységhez.
Link/Act
Folyamatosan
Az egyező port helyesen van csatlakoztatva.
Villog
Adatátvitel van folyamatban a porton keresztül.
Ki
A port nincs, vagy nem megfelelően van csatlakoztatva.
Bevezetés: üzemmódok
A PoE kapcsoló két üzemmóddal rendelkezik: VLAN Off (VLAN kikapcsolva) és VLAN
On (VLAN bekapcsolva). A csúszókapcsolóval állítsa a PoE kapcsolót a kívánt
üzemmódba az alábbi leírások szerint.
VLAN Off: A PoE kapcsoló alapértelmezett üzemmódja. Ebben a módban a váltó
összes portja tud kommunikálni egymással.
VLAN On: Ebben az üzemmódban a TEF1109TP-8-102W 1–8-es portja képes
kommunikálni az 9-ös porttal, de nem képesek kommunikálni egymással. Ezzel az
üzemmóddal csökkentheti a szórási viharokat, és elkülönítheti a DHCP-szórást.
Magyar
Светодиодный
индикатор
Статус
Описание
PWR
Горит постоянно
Коммутатор подключен к источнику питания.
Не горит
Коммутатор отключен от источника питания или
подключен к нему неправильно.
Link/Act
Горит постоянно
Порт подключен правильно.
Мигает
Через порт осуществляется передача данных.
Не горит
Порт не подключен или подключен неправильно.
Обзор режимов работы
У коммутатора с PoE есть два режима: VLAN Off и VLAN On. Используйте
переключатель для перевода коммутатора с PoE в нужный режим,
выбранный на основе описания.
VLAN Off: Режим по умолчанию коммутатора с PoE. В этом режиме все
порты могут подключаться друг к другу и имеют одинаковый приоритет.
VLAN On: В этом режиме порты 1–8 устройства TEF1109TP-8-102W могут
подключаться к порту 9, но не могут подключаться друг к другу. В этот
режим можно перейти, чтобы уменьшить broadcast шторм и изолировать
DHCP broadcast.
Русский
Indicator LED
Stare
Descriere
PWR
Rămâne aprins
Dispozitivul este conectat corect la sursa de alimentare.
Oprit
Switch-ul este deconectat de la sursa de alimentare sau nu
Link/Act
Rămâne aprins
Portul corespunzător este conectat corect.
Lumineaza
intermitent
Datele sunt transmise prin port.
Oprit
Portul este deconectat sau nu este conectat corect.
Prezentarea modurilor de lucru
Switch-ul PoE are două moduri: VLAN Off şi VLAN On. Setati switch-ul PoE în modul
dorit din comutator, conform următoarelor descrieri.
VLAN Off: Modul implicit al switch-ului PoE. În acest mod, toate porturile pot
comunica între ele.
VLAN On: În acest mod, porturile 1-8 ale TEF1109TP-8-102W pot comunica cu portul 9
dar nu pot comunica între ele. Puteți utiliza acest mod pentru a reduce broadcast
storm și pentru a izola DHCP broadcast.
Română
Kontrolka LED
Stan
Opis
PWR
Ciągłe światło
Urządzenie jest prawidłowo podłączone do źródła zasilania.
Wyłączone
Urządzenie jest odłączone od źródła zasilania lub nie zostało
do niego poprawnie podłączone.
Link/Act
Ciągłe światło
Gniazdo jest połączone poprawnie.
Miganie
Port obsługuje przesyłanie danych.
Wyłączone
Port jest odłączony lub niepoprawnie podłączony.
Wprowadzenie do trybów pracy
Switch PoE może działać w dwóch trybach: VLAN Off. i VLAN On. Za pomocą
przełącznika włącz w switchu PoE wymagany tryb pracy. Opisy trybów znajdują się
poniżej.
VLAN Off: Tryb domyślny switcha PoE. W tym trybie wszystkie porty switcha mogą się ze
sobą komunikować.
VLAN On: W tym trybie porty od 1 do 8 urządzenia TEF1109TP-8-102W mogą
komunikować się z portem 9, ale nie ze sobą nawzajem. Dzięki temu trybowi można
zmniejszyć liczbę burz broadcastowych i odizolować rozgłaszanie DHCP.
Polski
2. Connecting your devices
LED Indicator
Status
Description
PWR
Solid on
The switch is connected to a power supply properly.
Off
The switch is disconnected from a power supply or not
properly connected to a power supply.
Link/Act
Solid on
The port is connected properly.
Blinking
Data is being transmitted over the port.
Off
The port is disconnected or improperly connected.
Working mode introduction
The PoE switch has two modes: VLAN Off and VLAN On. You can use the working
mode toggle to set the PoE switch to required mode according to the following
descriptions.
VLAN Off: Default mode of the PoE switch. In this mode, all ports can communicate
with each other.
VLAN On: In this mode, ports 1 to 8 of TEF1109TP-8-102W can communicate with
All ports of your switch support the auto MDI/MDIX function, indicating that either straight cable or crossover
cable is acceptable to connect your switch to Ethernet devices.
Tips
To protect the switch from overload, PoE ports of your switch are assigned with power supply priorities,
and the priorities decrease as the port number increases. When the total power consumption of the
PoE-powered devices exceeds 92 W, the switch starts cutting the power supply from the port with the
lowest priority, until the total consumption does not exceed 92 W.
To protect your switch from lightning damage, connect the grounding terminal to a grounding cable.
Router
LAN port WAN port
LAN 1 LAN 2 LAN 3 LAN4 W AN
Uplink port
Power adapter
TEF1109TP-8-102W
Internet
Computer
PoE-powered devices
IP camera IP phoneAP
TEF1109TP-8-102W
VLAN
Off On
8FE+1GE Desktop Switch With 8-Port PoE
PWR
9 (Uplink)
Grounding terminal
Power socket
1. Installing the switch
Select one mounting method as required.
Option B. Wall mounting
Step 1: Drill two holes in the wall in a horizontal distance of 113.5 mm. Knock sleeve
anchors (self-preparation) into the holes using a rubber hammer, until the sleeve
anchor is level with the wall. Then tighten two screws (self-preparation) into the sleeve
anchors using a screwdriver, and keep the screw heads outside the wall at least 2.3
mm, to ensure that the switch can be hung on the screws firmly.
Step 2: Align the slots of the switch to the screw heads, and slip the switch to make it
fixed on the screws firmly.
Note: For safety, do not face the air vents of the switch down.
Option A. Desktop mounting
Put the switch on a stable and flat desktop.
Package contents
Quick installation guide * 1
Switch * 1
Power adapter * 1
Quick Installation Guide
8FE+1GE Desktop Switch With 8-Port PoE
Model: TEF1109TP-8-102W
If any item is missing, damaged or incorrect, please keep the original
packaging and contact the local reseller or distributor immediately.
113.5mm
2. 3mm
  • Page 1 1

Tenda TEF1109TP-8-102W Instrukcja instalacji

TEF1109TP-8-102W
Tenda
Marka
Tenda
Model
TEF1109TP-8-102W
Kategoria
Przełączniki sieciowe
Typ
Instrukcja instalacji
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty