Sports Attack Crick Attack Instrukcja obsługi

Marka
Sports Attack
Model
Crick Attack
Typ
Instrukcja obsługi
CRICKET BOWLING MACHINES
CRICKETCRICKET
CRICK ATTACK™ BOWLING MACHINE
PATENTS APPLIED FOR
INSTRUCTION MANUAL
REV08022022
OPERATION · SETUP · USE & CARE · SERVICE
SPORTS ATTACK LLC. | 800.717.4251 | www.sportsattack.com
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com xi
Warranty/Shipping
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully
inspected and packaged by skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation company assumes full responsibility
for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the
freight bill or express receipt, and that the note of loss or damage is signed by the
delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is
 unpacked,notifythetransportationcompanyorcarrierimmediately,andle
 “CONCEALEDDAMAGE”claimwiththem.Thismustbedonewithinfteen(15)days
from the date the delivery was made to you. Be sure to retain the container
for inspection.
Sports Attack LLC. cannot assume liability for damage or loss incurred in transit.
We will, however, at your request, supply you with the necessary documents to support
your claim.
RETURNS
To return an item, please
contact our Customer
Service Department at
800.717.4251.
A15%restockingfeewillbe
charged for any items accepted
for return. It is the customer’s
responsibility to handle the
repackingandshipment(aswell
asallassociatedfees)backto
Sports Attack.
No returns will be accepted after
30 days of receiving product.
WARRANTY STATEMENT
What is most important to Sports Attack is that your machine meets your expectations
of quality and performance. We stand behind the material and workmanship of our
machinesforve(5)yearsfromthedateororiginalpurchaseforinstitutionalandresidential
useandone(1)yearforcommercialenvironments,withthefollowingexceptions:
-Throwing Wheels are warranted for two (2) years;
-Electronic Controller is warranted for two (2) years; and,
-Throwing Wheel Motors are warranted for two (2) years.
This warranty excludes any cosmetic issues or normal wear and tear of the unit, and is not
ineffectifthemachinehasbeenmisused,misapplied,improperlyassembled,ormodied
without the express written permission of Sports Attack. In addition, this warranty does
not apply to damage in transit, in any accident unrelated to the direct operation of the
equipment,orbyre,oodoractofGod.
If you encounter any issues during the warranty period, Sports Attack will quickly get your
machine back in working order. If the warranty repair involves a replacement part, we will
make sure you get both the part and easy instructions for replacement at no cost to you.
If a service person is needed, Sports Attack will pay the pre-approved labor charge to get
your machine back in working order.
EFFECTIVE IMMEDIATELY: Warranty components such as motors, etc. now require
a picture of the component when submitting replacement request.
Please know that any problem can quickly be resolved with a phone call to our experienced,
responsivecustomerservicedepartmentat800.717.4251.Weareheretoansweryour
questions and to make sure your machine provides you years of service.
RETURNS
Sports Attack manufactures the highest quality sports training equipment in the world.
Ifforanyreasonyouarenotsatised,amachinecanbereturnedwithin30daysofreceipt
foranyreasonforafullrefundlessa10%restockingfee.Costofshippingtheunitbackto
Sports Attack will also be the responsibility of the purchaser. Please note that the refund
amount may be reduced by any non-cosmetic damage to the machine.
If you have any questions or concerns, please give our experienced, responsive customer
service department a call at 800.717.4251.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 1
Table of Contents/Introduction
TABLE OF CONTENTS
Warranty Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i
Safety Instructions .............................................................2
CRICKET BOWLING MACHINE OPERATION
Features & Operating Controls ................................................4
Set-up & Preparation .........................................................5
Training Practice .............................................................8
Shutting Down .............................................................10
MAINTENANCE & SERVICE
Care, Cleaning & Maintenance ...............................................11
Component Replacement ...................................................12
Exploded View .............................................................14
Parts List ...................................................................15
INTRODUCTION
Thank you for purchasing this Sports Attack LLC. equipment.
Proper assembly, careful operation and consistent maintenance of this equipment will
ensure that it gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly set up the Crick Attack,
and to use, care for and maintain the Crick Attack in a manner which will ensure its
optimum performance.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 2
Crick Attack™ Safety Instructions
SAFETY INSTRUCTIONS
ELECTRICAL SAFETY
Upto200ft.frompowersource,useaminimum#14/3grounded3-wire15ampminimum
rating extension cord.
Over 200 ft. from power source, consult a licensed electrician for required power cord size.
OPERATING SAFETY
CAUTION: Never reach down near moving throwing wheels for any reason! If it is
necessary to reach into the throwing wheels, ALWAYS:
1. Turn all three speed dials to “0”.
2. Turn on/off switch “OFF”.
3. Unplug Crick Attack from power source
4. Wait until the throwing wheels have come to a complete stop before
reachinghandsorngersanywherenearthethrowingwheels.
CAUTION: Carefully check Crick Attack for completeness and condition before
connecting to electrical power:
1. Throwing wheels must be tight on the motor shafts
2. Wheel guard and ball chute must be tightly fastened to the throwing head.
Carefully check the throwing wheels frequently for cleanliness, chips and cracks. Do not
use the machine if the throwing wheels are damaged, or if chips or cracks appear in the
wheels.(FordamagewithinWarrantyperiod,seeWarrantyStatement,pagei.)
ALWAYS set the speed controls to “0” before connecting the machine to power. Check
that the speed controls are at “0” before turning the on/off switch “ON”.
Do not allow anyone to walk in front of the machine if it is connected to electrical power.
WARNING
PERSONAL INJURY
HAZARD
Carefully read all instructions
in this manual, and all labels
and warnings on Crick Attack
before using this machine.
Use machine only under adult
supervision. Failure to operate
CrickAttack as described in
this manual can result in severe
personal injury or death.
Never loosen the horizontal
swivel lock while pitching to a
batter. If the lock is not secure,
the throwing head could pivot.
A loose swivel lock can allow a
pitch to be inside which could hit
the batter.
ELECTRICAL SHOCK
HAZARD
Crick Attack must be
connected to a properly
grounded electrical receptacle.
Do not operate on wet ground.
CAUTION
PERSONAL INJURY
HAZARD
Keep hands away from throwing
wheels anytime the machine is
connected to a power source.
Carefully check Crick Attack for
completeness and condition
before connecting to electrical
power.
EQUIPMENT
ELECTRICAL DAMAGE
Keep hands away from throwing
wheels anytime the machine is
connected to a power source.
Carefully check Crick Attack for
completeness and condition
before connecting to electrical
power.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 3
Crick Attack™ Safety Instructions
SAFETY INSTRUCTIONS (cont’d)
BALL SELECTION
Never mix cricket balls with synthetic Bowling machine balls.
Be careful not to mix new with old balls or balls from different manufacturers.
Balls must be consistent in type and amount of wear to produce repeatability.
Never use wet balls!
BATTING PRACTICE
The horizontal swivel lock must be securely tightened before the batter enters the net.
ALWAYS test and adjust the Crick Attack before a batter enters the net:
 1.AdjustsothatCrickAttackthrowsaballstraightatrst,thenread
just for variations.
2. Throw test balls until required velocity, swing or spin are reached.
3. Throw several balls to verify repeatability.
DO NOT make any changes while the batter is in the net.
Batter and machine operator must wear batting helmets.
Only one person at a time should operate the machine.
Always present the ball to the batter before feeding the ball into the machine.
Operator must stand behind a protective screen to prevent injury from balls off the bat.
Screen is not included with Crick Attack.
FIELDING PRACTICE
Both the elevation control and swivel lock must be released so that the throwing
head moves freely through the intended range of motion.
Never reach up chute to push ball into the throwing wheels.
Keephandsandngerswellawayfromthethrowingwheels.
Be careful to keep all persons away from in front of Crick Attack.
For best accuracy, use dimpled bowling machine balls.
NOTE:Vertical(elevationcontrol)mustbeadjustedwheneveryouchangedeliveries.
Never put machine on 10,10, 10, it is very dangerous.
CAUTION
PERSONAL INJURY
HAZARD
Always use a protective screen to
protect the operator from the ball
offthebat.(Screennotincluded
withCrickAttack.)
Always wait for all three throwing
wheels to come to a complete stop
before transporting Crick Attack,
lifting the throwing head or
performing any repairs.
ADDITIONAL
INFORMATION
If you have any questions
regarding the safe operation
of this equipment, please call:
Sports Attack
Customer Service:
800.717.4251 or
775.345.2882
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 6
4
Features & Operating Controls
CRICKET FEATURES & OPERATING CONTROLS
CRICK ATTACK PITCHING MACHINE
PATENTS APPLIED FOR
Detail A control panel frame here with labels
Ball Chute
Travel Lock
(opposite side)
Elevation
Control
Horizontal
Swivel Lock
Wheel Guard
Throwing
Wheel
Serial
Number
Transport
Wheel
Under Carriage
Travel lock must be secure
prior to movement.
Figure 1 Position Crick Attack
Tip up onto Wheel Guard;
Insert two front legs
Figure 2 Set Crick Attack
upright
Carefully tilt Crick Attack up
onto its legs
SAFETY HINT
Keep your back straight and lift
with your legs. Be ready to grab
the wheel guard and guide Crick
Attack into the upright position.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 5
Set-up & Preparation
CRICKET SET-UP & PREPARATION
1. Installtherearleg(Note: the leg has a push button, which locks the leg into the
socket).RollCrickAttackintopositionatthebowlersend.
2. Be sure the horizontal swivel lock is tightened securely.
3. Tilt Crick Attack forward until it rests on the throwing wheel guard.
1. Insert the two front legs into the front sockets in the undercarriage
(Note:thefrontlegsalsohavelockingpushbuttons).
2. See Figure 2 on page 4.
Walk around to the front of Crick Attack, and, with your back to home plate, reach
down and grasp the wheel guards. Then, lift Crick Attack up and over the front legs
and set it gently onto the rear leg.
3. Position Crick Attack:
a. To approximate the release point of a live bowler, position Crick Attack
 sothattherearlegislevelwiththestumps(TBC).
b. Then, sight down ball chute. Move the swing control right or left to adjust
machine so that it is pointing directly at home plate.
c. Check the horizontal swivel lock to make sure it remains tight.
4. Unlock the travel lock. Turn the handle of the elevation control counter-clockwise
until the bar of the travel lock snaps back out of the way.
5. Adjust the throwing head:
a. Turn the handle of the elevation control clockwise. Raise the throwing head
until it will throw somewhere near the required height.
b. This initial adjustment will come through experience. To start, turn the
elevation adjustment 10 turns clockwise.
6. Examine Crick Attack for condition and completeness:
a. Be sure the horizontal swivel lock is secured.
b. Throwing wheels must be tight on the motor shafts. Check that the keyway
retaining bolts are tight.
c. Wheel guard and ball chute must be securely fastened to the throwing head.
7. Be certain on/off switch is turned “OFF”, then plug Crick Attack into an extension
cordorotherpowersource.(Seegeneratorinformationatrightifapplicable.)
WARNING
HAZARD FROM
HIGHSPEED
PROJECTILES
Being struck by a pitched ball
can cause serious injury or death.
Make sure that no one steps in
front of Crick Attack while it is
connected to electric power.
Clear all hitters away from home
plate, the batter’s box and the
backstop area before connecting
Crick Attack to electric power.
GENERATOR
INFORMATION
1. Crick Attack requires a
generator capable of
providing clean electric-
ity 2000 watts at 120 volts
60hz.
2. Be sure the on/off switch
is “OFF” before plugging
Hack Attack into the
generator.
3. Start the generator and
allow it to reach full speed
before turning the on/off
switch “ON”.
IMPORTANT: Generator speed
uctuationscandamage
the electronic speed control.
Maintain adequate fuel in the
generator at all times.
4. Turn the on/off switch
“OFF” before shutting off
the generator and before
unplugging Crick Attack.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 6
Set-up & Preparation
INSTALLING EXTENDED LEGS ONTO YOUR
CRICK ATTACK CRICKET BOWLING MACHINE
(Requires two people)
1. FRAMELOCKthethrowinghead(seemanualforinstruction;ref.ShuttingDown)
Figure 1
2. Remove all three standard legs by laying down the machine.
NOTE: See Figure 2. After standard legs are removed insert the extended legs.
3. See Figure 3-7. 2 people need to lift it up.
Figure 2 Insert new extended legs into sockets Figure 3 Stand the machine up - 2 people lift
Figure 1 Frame Lock
ADJUSTABLE
HEIGHT LEGS
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 7
Set-up & Preparation
Figure 6 Figure 7
Figure 4 Figure 5
INSTALLING EXTENDED LEGS ONTO YOUR
CRICK ATTACK CRICKET BOWLING MACHINE - CONT’D
(Requires two people)
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 8
Cricket Batting Practice
NOTE: As wheel speeds are
changed for different velocities
and spins, the ball will be
pitched to differing locations.
Compensate for these changes
by turning the elevation control,
and by moving the rear leg.
Figure 3 Present the ball to the hitter
Figure 4 Feeding the Ball
IMPORTANT: Hitter should
stride the instant he sees the
ball release from the feeder’s
hand at the upper end of the
ball chute.
CRICKET BATTING PRACTICE
SET UP
1. Turn the on/off switch “ON”.
2. Set the speed control dials*:
Top Left to “4”
Top Right to “4”
Bottom to “4”
3. Check again to make sure no one is in front of Crick Attack or anywhere near the
net.Then,feedaballdowntheballchutetobowltherstball.
4. Note where the ball goes in relation to the stumps. Adjust the ball to the left or right
by shifting the rear leg:
a. To move the ball left, move the swing control to the right.
b. To move the ball right, move the swing control to the left.
 c. Finalnehorizontaladjustment(inside/outside)ismadeusingthe
Horizontal Control Handle. First loosen the Horizontal Swivel Lock than
  adjustusingHorizontalControlHandle.Andnallyre-tightenthe
Horizontal Swivel Lock Handle.
5. Adjust the length:
a. Turn the elevation control clockwise to bowl fuller.
b. Turn the elevation control counter-clockwise to bowl shorter.
6. Adjust the speed control dials to produce the required speed. Larger numbers
equal higher speed.
7. Feed a second ball.
8. Repeatsteps4,5and6untilthedesiredswing,spin,accuracyandspeedareachieved.
9. Refer to “Selecting the Type of Bowling”, page 7.
10. Feed several more test balls to ensure the machine is set correctly.
11. After you are sure desired delivery is repeating, allow the batter to step into the net.
12. See Figures 3 and 4 at left.
a. Before each feed present the ball to the batter.
b. Drop the ball into the ball chute.
WHEN FEEDING TO A BATTER
Proper feeding technique is important to take advantage of Crick Attack’s life-like
vision and timing.
When feeding:
1. Be sure batter is ready.
2. Present the ball to batter by raising it so batter can clearly see it, then place
ballatthetopoftheballchute,seatingitrmlyagainsttheballchute.Theball
should be held back against the chute to ensure a smooth consistent feed.
3. Release the ball to roll down the ball chute and into the throwing wheels.
WARNING
HAZARD FROM
HIGHSPEED
PROJECTILES
Being struck by a thrown ball can
cause serious injury or death.
Make sure that no one steps in
front of Crick Attack while
it is connected to electric power.
Clear all hitters away from the
backstop area before connecting
Crick Attack to electric power.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 11
9
Cricket Batting Practice
CRICKET BATTING PRACTICE (cont’d)
SELECTING THE PITCH
1. NOTE: Vertical(elevation)andhorizontal(swivel)mustbothbeadjustedwhenever
you change speed or spin.
Always have the batter step away from the wicket area before adjusting speed or spin.
BALL SELECTION
1. Never mix different type of cricket balls.
2. Be careful not to mix new with old balls, or balls from different manufacturers.
3. Balls must be consistent in type and amount of wear to produce repeatability.
4. NEVER USE WET BALLS!
Real leather OR balles designed to work in cricket machines are best.
Discard old or soft leather balls from your Crick Attack batting sessions. Similarly,
discard older worn cricket pitching balls.
WARNING
PERSONAL INJURY
HAZARD
Never reach down near throwing
wheels for any reason! Always
turn all three speed control
dials “OFF”, turn the on/off switch
“OFF”, unplug Crick Attack from
the power source and wait until
the throwing wheels have come
to a complete stop before
reachinghandsorngers
anywhere near throwing wheels.
Right wheel
speed control
Left wheel
speed control
Bottom wheel
speed control
IN SWINGOUT SWING
OFF CUTTER
LEG CUTTER
STRAIGHT
Knuckleballs thrown too fast are dangerous (and unrealistic).
Throw test pitches until desired velocity and break are achieved.
LEFT
4 ± 1
6 ± 1
RIGHT
4 ± 1
6 ± 1
BOTTOM
4 ± 1
3 ± 1
LEFT
2 ± 1
5 ± 1
RIGHT
8 ± 1
9 ± 1
BOTTOM
1 ± 1
3 ± 1
TOP SPIN
LEFT
0 ± 1
RIGHT
0 ± 1
BOTTOM
5 ± 1
LEFT
8 ± 1
9 ± 1
RIGHT
2 ± 1
5 ± 1
BOTTOM
1 ± 1
3 ± 1
OFF SPIN
LEFT
0 ± 1
RIGHT
5 ± 1
BOTTOM
0.2 ± 1
LEFT
6 ± 1
7 ± 1
RIGHT
2.5 ± 1
5.5 ± 1
BOTTOM
1 ± 1
3.5 ± 1
LEG SPIN
LEFT
5 ± 1
RIGHT
0 ± 1
BOTTOM
0.2 ± 1
RIGHT
6 ± 1
7 ± 1
BOTTOM
1 ± 1
3.5 ± 1
LEFT
2.5 ± 1
5.5 ± 1
80 KmPH
100 KmPH
80 KmPH
100 KmPH
70 KmPH
100 KmPH
70 KmPH
100 KmPH
60 KmPH 60 KmPH
Figure 5 Bowling Style Selection Chart - These settings are a general guideline for
professional bowling for professional batters only. Adjustments for players of lesser
skill can be made from these settings.
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 10
Shutting Down
CRICKET SHUTTING DOWN
TURNING CRICK ATTACK “OFF”
1. Set each speed control dial to “0”.
2. Turn the on/off switch “OFF”.
3. Unplug Crick Attack from the power source.
PUTTING CRICK ATTACK AWAY
1. Be absolutely sure that the throwing wheels have completely stopped turning.
2. See Figure 7 at right:
a. Turn the elevation adjustment counter-clockwise until the throwing head
is all the way down against the elevation control nut.
b. Push and hold the travel lock all the way in.
c. Turn the elevation adjustment clockwise until the throwing head is held
tightly against the travel lock. Tighten just enough to secure the throwing
head. It is not necessary to over tighten.
3. Using the rear leg as a handle, tip Crick Attack up and over onto the wheel guard.
4. Remove(unsocket)bothfrontlegsandstorebyinsertinginthetravelstoragesockets.
5. See Figure 8 at right:
Again, using the rear leg as a handle, tip Crick Attack back until machine can be
comfortably rolled on the travel wheels. Crick Attack can now be rolled and
maneuveredoffoftheeld.
6. To transport Crick Attack in a car, remove the throwing head:
a. Be sure the travel lock is engaged and the throwing head is tightly secured
to the yoke.
b. Loosen the horizontal swivel control. Turn it counter-clockwise until the
throwing head is free to lift out of the swivel.
c. Lift the throwing head straight up and clear of the undercarriage.
SUGGESTION: The throwing head, while awkward, can be carried for short
distances by gripping the top section of the wheel guard and balancing the
piece against your thighs as you walk.
d. To prevent damage in transport, rest the throwing head on the wheel
guard and yoke; motors should be down, and the control panel pointing up.
Figure 7 Secure the Travel Lock
Figure 8 Maneuvering
Storing Legs in Travel Socket
ELEVATION
CONTROL
LOCKING
TAB ON
THROWING
HEAD
TRAVEL
LOCK
USE TRANSPORT
LEG AS A HANDLE
TO MANEUVER
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 11
CARE, CLEANING & MAINTENANCE
LUBRICATION (onceperseason,orasrequired):
1. Elevation Control
a. Apply fresh grease.
b. Reinstall, making sure that the tension spring is around the threads.
 (Seeitem30,30Band31onpage13).
2. Travel Lock
3. Applyasmallamountofgreasewherethepinpassesthroughthetting.Makesure
the travel lock operates freely.
4. Horizontal Swivel Lock
a. Completely remove the horizontal swivel lock nut. Clean all old grease,
dirt, etc. from the threads.
b. Wipe the threads with a very small amount of fresh grease.
c. Reinstall.
THROWING WHEEL MOTORS
Motors are sealed and require no lubrication.
Check bolts for tightness once a season. Tighten bolts securely, but do not over-tighten.
See Figures 7 and 8 on page 11.
CLEANING THE THROWING WHEELS
The throwing wheels must be kept clean to maintain accuracy. Clean the wheels
periodically to control the build-up of grass and dirt.
1. Turn the on/off switch “OFF” and allow the wheels to come to a complete stop.
Unplug Crick Attack from electric power.
Dampen a rag with soap and water. Turn the throwing wheel by hand and scrub the
wheel until the build-up is removed. For very heavy build-up, a synthetic scouring pad,
such as a Scotch-Brite® scouring pad, or medium sandpaper may be used sparingly.
Acetone may be
required to help loosen the build-up of dirt or ball residue.
EXAMINE THE MACHINE
Examine Crick Attack for condition and completeness before every use:
1. For batting practice, be sure the horizontal swivel lock is secured.
2. Throwing wheels must be tight on the motor shafts. Check that the keyway retaining
bolts are tight.
3. Wheel guard and ball chute must be securely fastened to the throwing head.
CAUTION
PERSONAL INJURY
HAZARD
Never attempt to clean the
throwing wheels while they are
turning. Rags or implements
caught in spinning wheels can
cause serious injury.
Unplug the machine before
cleaning the wheels or
performing any service.
CHEMICAL HAZARD
Acetone
Read and follow the directions
and safety instructions on the
acetone container.
FIRE HAZARD
Acetone
Acetoneisammable.Donot
useacetonearoundareor
ame.Donotuseacetonenear
a running generator or other
source of ignition.
Care & Cleaning
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 12
COMPONENT REPLACEMENT
THROWING WHEEL REPLACEMENT
1. Turn the on/off switch “OFF” and unplug the power cord. For the bottom throwing
wheel, remove 6 bolts holding the wheel guard to the main casting.
2. Hold the wheel so that it cannot move. Turn the keyway retaining bolt counter-
clockwise using a box end wrench.
3. Remove the bolt and washers.
4. Work the wheel off of the motor shaft. Be sure to catch the key as it is freed from
the keyway.
5. Ball throwing wheels are machine balanced. Small holes in the side of the wheel
are applied at the factory and are normal. A slight wobble is normal.
Reassemble in reverse order.
a. Install wheel to motor shaft with key slots aligned.
 b. Besurethekeyisinplace,andinsertedsothatitisushwiththebossat
the wheel center.
c. Be sure the washer and lock washer are installed in the right order, and
that the keyway retaining bolt is tightened.
d. Test the wheel by spinning it by hand and making sure that it spins freely
without wobble before turning the unit “ON”.
e. Be sure the wheel guard is properly and securely reinstalled.
MOTOR REPLACEMENT
1. Turn the on/off switch “OFF” and unplug the power cord.
2. Removethethrowingwheel(seeabove).
3. Remove four screws holding controller into main casting. Note the position of the
motor wires on the controller, then disconnect the wires. See Figure 10 on page 12.
4. Note the routing of the motor wires. Loosen any wire clamps.
5. Remove four bolts holding the motor to the main casting. See Figures 7 and 8
on page 11.
6. Reassemble in reverse order.
Component Replacement
NOTE: On the bottom wheel, the
Frontwheelguard(part43on
page13)mustberemovedprior
to the removal of the motor or
ball-throwing wheel.
Hold wheel while loosening bolts.
NOTE: Check bolts for tightness once a season. Tighten bolts securely,
but do not over-tighten.
When replacing the motor, you
will see two sets of bolts:
2 - 1/4” x 1 1/4” coarse thread bolts
2-5/16”x11/2”coarsethread
bolts
The wrench or socket size needed
for the 1/4” bolt is a 7/16”.
The wrench or socket size needed
forthe5/16”boltisa1/2”.
Figure 7 Shown using a 6” extension
with 1/2” socket.
Figure 8 Shown using a 6” extension with
7/16” socket.
1/2” KEYWAY
RETAINING BOLT
LOCK WASHER
FL AT WASHER
KEY
MOTOR
THROWING
WHEEL
HOLES DRILLED
FOR BALANCE
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 13
COMPONENT REPLACEMENT (cont’d)
CONTROLLER REPLACEMENT
1. Turn the on/off switch “OFF” and unplug the power cord.
2. Remove four screws holding controller faceplate into main casting. Note the
position of the main power and motor wires on the controller, then disconnect the
wires. See Figure 10 on page 12 for the three motor wires. See Figure 11 on page
12 for the main power cord wires.
3. Loosen the nuts holding the three speed control shafts to the faceplate, then
remove the controller.
Reassemble in reverse order.
Be sure wires are correctly reinstalled. Motor wire connectors are different sizes.
Be sure they are installed on the correct size terminal. See Figure 10 for the motor
wires and Figure 11 for the power cord wire.
Component Replacement
Figure 9 Wiring diagram from the control board side.
Figure 10 Wiring diagram for all three motors.
Right Motor Circuit Breaker
Bottom Motor
Left Motor
POWER CORD WIRE
CONNECTING WIRES
Motor Black White
Wire Wire
Right A- A+
Left A+ A-
Bottom A- A+
Black (#1)
Circuit breaker
White (#2)
N on green control board
Green (#3)
Grounds to machine
Black motor wires are 3/16”
female disconnect and white
wires are 1/4” female disconnect.
#3
#1
#2
Figure 11
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 14
EXPLODED VIEW
Exploded View
1Cane Tip
2 Leg, Cricket
5Undercarriage
13 Horizontal Swivel
Lock Handle
14 Swivel Lock Pivot Bolt
Assembly
17 Leg Spring, Dual Snap
19 TravelWheel(withaxle,
bolt,not,washers)
21 Yoke
26 Frame Lock Pin
27 Spring, Lock Pin
30 Elevation Control Nut
Assembly
30B Tension Spring,
Elevation Control
31 Handle, Elevation Control
34 Main Casting,
Throwing Head
35 Upper Clamp
37 Motor, Variable Speed
38 ThrowingWheel(with
key,bolt,washers)
39 Ball Chute
43 Wheel Guard
49 Grommet, Wiring
60 Control Face Plate
61 Knob, Speed Control
63 Controller
64 Safety Reset
65 On/Off Switch
67 Swing Control Handle
Decal Set, Safety and
Operating Info
2
5
21
31
37
37
37
38
38
34
35
39
38
30B
30
27
26
17
14
43
19
63
60
49 61
64
65
67
13
1
2
CRICK ATTACK™ CRICKET BOWLING MACHINE
Sports Attack, LLC. • 800.717.4251 • www.sportsattack.com 15
Parts List
EM PART NO. DESCRIPTION QTY PER
1280-1000 Cane Tip 3
2532-0026 Leg, Cricket 3
5513-1309 Undercarriage, Crick Attack 1
13 533-0500 Horizontal Swivel Lock Handle 1
14 533-0501 Swivel Lock Pivot 1
17 270-0002 Leg Spring Dual Snap 1
19 281-0002 Travel Wheel (with axle, bolt, not washers) 2
21 533-1302 Yoke 1
26 531-1506 Frame Lock Pin 1
27 270-0005 Spring Lock Pin 1
30 531-1505 Fitting, Elevation Control 1
30B 310-0021 Tension Spring, Elevation Control 1
31 531-1504 Handle, Elevation Control 1
34 290-0014 Main Casting, Throwing Head 1
35 533-0002 Wire Clamp 1
37 210-1803 Motor, Variable Speed 180V 3
38 531-0001 Throwing Wheel (with key, bolt, washers) 3
39 533-1307 Ball Chute 1
43 533-1306 Wheel Guard 1
49 280-3007 Grommet, Wiring 1
60 533-1503 Control Face Plate 1
61 280-2003 Knob, Speed Control 3
63 530-0031 Controller 1
64 232-0002 Safety Reset 1
65 223-0004 On/Off Switch 1
67 533-0600 Swing Control Assembly 1
281-0001 Travel Wheel, Extra-Heavy Duty
Decal Set, Safety and Operating Info 1
Power Cord (240v-AU) 1
PARTS LIST
Parts List
To order additional parts,
please contact:
Sports Attack
Customer Service Dept.
Ph 800.717.4251
Fx 775.345-2883
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Sports Attack Crick Attack Instrukcja obsługi

Marka
Sports Attack
Model
Crick Attack
Typ
Instrukcja obsługi
ściągnij PDF
raport

w innych językach

Inne dokumenty