Parkside 73867 Operation and Safety Notes

POWER ENGRAVING TOOL PGG 15 A1

POWER ENGRAVING TOOL

Operation and Safety Notes

Translation of original operation manual

URZĄDZENIE DO GRAWEROWANIA

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

GRA VÍRO V A CÍ PŘÍSTRO J

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

GRA VIERGERÄ T

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

GRA VÍRO V AČKA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

IAN 73867

GB Operation and Safety Notes Page 5

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 21

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 37

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 53

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 69

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

B

1 2 3

45

6

A

7

5 GB

Table of contents

Introduction

Proper use ................................................................................ Page 7

Features and equipment ......................................................... Page 7

Included items ......................................................................... Page 8

Technical details ...................................................................... Page 8

General safety advice for electrical

power tools ....................................................................... Page 9

1. Workplace safety ............................................................... Page 10

2. Electrical safety ................................................................... Page 10

3. Personal safety .................................................................... Page 11

4. Careful handling and use of electrical power tools ......... Page 12

5. Service ................................................................................. Page 13

Operation

Switching on / off .................................................................... Page 14

Setting the stroke rate ............................................................. Page 14

Changing the engraving point ............................................... Page 15

Advice on use .......................................................................... Page 15

Cleaning ............................................................................... Page 16

Service ................................................................................... Page 16

Warranty ............................................................................. Page 17

Disposal ................................................................................ Page 18

Manufacturer’s Declaration of

Conformity / Manufacturer ................................... Page 18

6 GB

Introduction

The following pictograms are used in these operating

instructions / on the device:

Read instruction manual!

V

~

Volt (AC)

A

Amps

Observe caution and safety notes!

Risk of explosion!!

Keep children away from electrical power tools!

Caution – electric shock! Danger to life!

Risk of loss of life by electric shock from damaged mains

lead or mains plug!

Wear hearing protection, dust protection mask, protective

glasses and protective gloves.

Dispose packaging and appliance in an environmen-

tally-friendly way!

7 GB

Introduction

Power engraving tool PGG 15 A1

Introduction

We congratulate you on the purchase of your new device.

You have chosen a high quality product. The instructions for

use are part of the product. They contain important information

concerning safety, use and disposal. Before using the product, please

familiarise yourself with all of the safety information and instructions for

use. Only use the unit as described and for the speciﬁed applications.

If you pass the product on to anyone else, please ensure that you also

pass on all the documentation with it.

Proper use

This product is intended for engraving or decorating materials such

as metal, plastic, glass, ceramic, wood, leather and stone. Any other

use or modiﬁcation to the drill / grinder shall be considered as improper

use and could give rise to considerable dangers. The manufacturer will

not accept liability for loss or damage arising from improper use. Not

intended for commercial use.

Features and equipment

1

ON / OFF switch

2

Stroke switch

3

Hanging eye

4

Mains lead

5

Engraving point

8 GB

6

Engraving point holder

7

Engraving stencils

Included items

1 Power engraving tool PGG 15 A1

2 Engraving stencils

1 Operating instructions

Technical details

Rated voltage: 230 V∼ 50 Hz

Mode of operation: intermittent operation: S3 20 %

Note: A duty cycle (in %) deﬁnes explicitly the maximum continuous

duration of use and the subsequent rest period. In this case the tool

requires a cooling phase of eight minutes after an operating period of

two minutes, for example.

Rated current: 0.15 A

Stroke rate: 6000 min

-1

Noise and vibration data:

Measured values for noise are determined in accordance with

EN 60745. The A-weighted noise level of the electrical power tool

are typically:

Sound pressure level: 74.4 dB(A)

Sound power level: 85.4 dB(A)

Uncertainty K: 3 dB

Introduction / General safety advice for electrical power toolsIntroduction

9 GB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration: 1.582 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level given in these instructions has

been measured in accordance with a standardised measurement pro-

cedure speciﬁed in EN 60745 and can be used to compare devices.

Diﬀerent uses of the device give rise to diﬀerent vibration levels and in

many cases they may exceed the values given in these instructions. It is

easy to underestimate the vibration load if the electrical power tool is

used regularly in particular circumstances.

Note: If you wish to make an accurate assessment of the vibration

loads experienced during a particular period of working, you should

also take into account the intervening periods of time when the device

is switched oﬀ or is running but is not actually in use. This can result in

a much lower vibration load over the whole of the period of working.

General safety advice for

electrical power tools

Read all the safety advice and instruction

s!

Failure to observe the safety advice and instructions may result in electric

shock, ﬁre and / or serious injury.

Keep all the safety advice and instructions in a safe place

for future reference!

Introduction / General safety advice for electrical power toolsIntroduction

10 GB

The term “electrical tool” used in the safety advice refers to electrical

tools powered by mains electricity (by means of a mains lead) and elec-

trical tools powered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) Keep your working area clean and well lit. Untidy or

poorly lit working areas can lead to accidents.

b)

Do not work with the device in potentially

explosive environments in which there are

inflammable liquids, gases or dusts. Electrical

power tools create sparks, which can ignite dusts or fumes.

c)

Keep children and other people away while

you are operating the electrical tool. Distrac-

tions can cause you to lose control of the device.

2. Electrical safety

a)

T

he mains plug on the device must match the mains

socket. The plug must not be modified in any way.

Do not use an adapter plug with devices fitted with

a protective earth. Unmodiﬁed plugs and matching sockets

reduce the risk of electric shock.

b) Avoid touching earthed surfaces such as pipes, radia-

tors, ovens and refrigerators with any part of your

body. There is an increased risk of electric shock if your body is

earthed

.

c) Keep the device away from rain or moisture. Water en-

tering an electrical device increases the risk of electric shock.

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

11 GB

d) Do not use the mains lead for any purpose for

which it was not intended, e.g. to carry the de-

vice, to hang up the device or to pull the mains

plug out of the mains socket. Keep the mains lead

away

from heat, oil, sharp edges or moving parts of the

device. Damaged or tangled mains leads increase the risk of

electric shock.

e) When working outdoors with an electrical power tool

always use extension cables that are also approved

for use outdoors. The use of an extension cable suitable for

outdoor use reduces the risk of electric shock.

f) Use a residual current device (RCD) for protection if

operating the electrical power tool in a moist environ-

ment is unavoidable. The use of an RCD reduces the risk of

electric shock.

3. Personal safety

a) Remain alert at all times, watch what you are doing

and always proceed with caution. Do not use the de-

vice if you are tired or under the influence of

drugs,

alcohol or medication. One mo

ment of carelessness when using

the device can lead to serious injury.

b)

Wear personal protective equipment and

always wear safety glasses. The wearing of per-

sonal protective equipment such as dust masks, non-slip

safety shoes, safety helmets or ear protectors, appropriate to the

type of electrical power tool used and work undertaken, reduces

the risk of injury.

c) Avoid unintentional operation of the device. Check

that the electrical power tool is switched off before y

ou

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

12 GB

connect it to the mains, pick it up or carry it. Accidents

can happen if you carry the device with your ﬁnger on the ON /

OFF switch or with the device switched on.

d) Remove any setting tools or spanners before you

switch the device on. A tool or spanner left attached to a

rotating part of a device can lead to injury.

e) Avoid placing your body in an unnatural position.

Keep proper footing and balance at all times. By doing

this you will be in a better position to control the device in unfore-

seen circumstances.

f) Wear suitable clothing. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves clear of

moving parts. Loose clothing, jewellery or long hair can become

trapped in moving parts.

g) If vacuum dust extraction and collection devices are fit

ted

do not forget to check that they are properly con

nected

and correctly used. The use of these devices reduces the haz-

ard presented by dust.

4. Careful handling and use of

electrical power tools

a) Do not overload the device. Always use an electrical

power tool that is intended for the task you are un-

dertaking. By using the right electrical power tool for the job

you will work more safely and achieve a better result.

b) Do not use an electrical power tool if its switch is de-

fective. An electrical power tool that can no longer be switched

on and oﬀ is dangerous and must be repaired.

c) Pull the mains plug from the socket before you make

any adjustments to the device, change accessories or

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

13 GB

when the device is put away. This precaution is intended to

prevent you from unintentionally starting the device.

d) When not in use always ensure that electrical power

tools are kept out of reach of children. Do not let any-

one use the device if he or she is not familiar with it

or has not read the instructions and advice. Electrical

power tools are dangerous when they are used by inexperienced

people.

e) Look after the device carefully. Check that moving

parts are working properly and move freely. Check

for any parts that are broken or damaged enough to

detrimentally affect the functioning of the device.

Have damaged parts repaired before you use the

device. Many accidents have their origins in poorly maintained

electrical power tools.

f) Keep cutting tools clean and sharp. Carefully maintained

cutting tools with sharp cutting edges are less likely to jam and

are easier to control.

g) Use the electrical power tool, accessories, inserted

tools etc. in accordance with these instructions and ad-

vice, and the stipulations drawn up for this particular

type of device. In doing this, take into account the

working conditions and the task in hand. The use of

electrical power tools for purposes other than those intended can

lead to dangerous situations.

5. Service

a) Have your device repaired at the service centre or by

qualified specialist personnel using original

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

14 GB

manufacturer parts only. This will ensure that your device

remains safe to use.

Operation

Never use the device for a purpose for which it was not intended or

with non-original parts / accessories. The use of tools or accessories

other than those recommended in the operating instructions could lead

to you suﬀering an injury.

Switching on / oﬀ

Insert the mains plug into a mains socket.

Switching on:

Press the ON / OFF switch

1

.

Switching off:

Release the ON / OFF switch

1

.

Setting the stroke rate

The stroke switch

2

is used to set the penetration depth of the engrav-

ing. A low setting is normally adequate for most engraving tasks.

Turn the switch for the number of strokes

2

in the + direction to

increase the penetration depth.

Turn the switch for the number of strokes

2

in the – direction to

decrease the penetration depth.

OperationGeneral safety advice for electrical power tools / Operation

15 GB

Note: Take care when increasing the penetration depth that you do

not turn the stroke switch

2

too far in the + direction. Otherwise the

switch could screw oﬀ the device.

Changing the engraving point

RISK OF INJURY! Switch the device oﬀ before

performing any tasks on the device and pull the mains plug out of the

mains socket.

Replace the engraving point

5

as soon as it becomes too worn

and no longer provides the desired engraving performance. Turn

the engraving point holder

6

anticlockwise until the engraving

point

5

is released.

Remove the spring and the plain washer.

Push the plain washer and spring on to a new engraving point

5

.

Then insert this and turn the engraving point holder

6

clockwise

to lock the engraving point in position.

Ensure that the engraving point

5

is properly ﬁxed in position.

Advice on use

You can use the mini-engraver to produce creative, individual engravings.

For example, you can use it to place identifying marks on your valuables.

You can place numbers and letters on metal, glass, plastic, wood,

ceramic and stone. This is done with the help of the supplied engraving

stencils

7

, see Figs. A and B.

Hold the device at an angle, as you would a pencil.

Your arm should rest on the table.

OperationGeneral safety advice for electrical power tools / Operation

16 GB

Using very light pressure, guide the engraving point

5

over the

workpiece. Find the ideal speed of movement by trial and error on

a piece of waste material.

Note: The engraving point

5

supplied with the product is made

from tungsten steel. Therefore it is not suitable for engraving electronic

media such as CDs, DVDs etc. It could damage these materials and

render them illegible.

Cleaning

Before performing any cleaning or maintenance

work, always remove the mains plug from the socket.

Clean all the dirt oﬀ the device. Use a dry cloth for cleaning.

Service

Have your device repaired at the ser-

vice centre or by qualified specialist personnel using

original manufacturer parts only. This will ensure that your

device remains safe to use.

If the plug or lead needs to be replaced,

always have the replacement carried out by the man-

ufacturer or its service centre. This will ensure that your device

remains safe to use.

WarrantyOperation / Cleaning / Service

17 GB

Warranty

The warranty for this appliance is for 3 years from the date

of purchase. The appliance has been manufactured with

care and meticulously examined before delivery. Please

retain your receipt as proof of purchase. In the event of a

warranty claim, please make contact by telephone with

our Service Department. Only in this way can a post-free

despatch for your goods be assured.

The warranty covers only claims for material and maufacturing defects,

but not for transport damage, for wearing parts or for damage to frag-

ile components, e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and improper handling, use of

force and internal tampering not carried out by our authorized service

branch. Your statutory rights are not restricted in any way by this warranty.

The warranty period will not be extended by repairs made unter warranty.

This applies also to replaced and repaired parts. Any damage and de-

fects extant on purchase must be reported immediately after unpacking

the appliance, at the latest, two days after the purchase date. Repairs

made after the expiration of the warranty period are subject to pay

ment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 73867

WarrantyOperation / Cleaning / Service

18 GB

Manufacturer’s Declaration of Conformity / Manufacturer… / Manufacturer’s Declaration of Conformity / Manufacturer

Disposal

The packaging is wholly composed of environmentally-

friendly materials that can be disposed of at a local

recycling centre.

Do not dispose of electric tools in

the household waste!

In accordance with European Directive 2002 / 96 / EC about waste

electrical and electronic equipment and its transposition into national

legislation, worn out electric tools must be collected separately and

taken for environmentally compatible recycling.

Contact your local refuse disposal authority for more details of how to

dispose of your worn out electrical devices.

Manufacturer’s Declaration of

Conformity / Manufacturer

We, Kompernaß GmbH, the person responsible for documents:

Mr Semi Uguzlu, Burgstr. 21, D-44867 Bochum, Germany, hereby

declare that this product complies with the following standards, norma-

tive documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

19 GB

Manufacturer’s Declaration of Conformity / Manufacturer… / Manufacturer’s Declaration of Conformity / Manufacturer

Electromagnetic compatibility

(2004 / 108 / EC)

Applicable harmonized standards

EN 60745-1:2009

EN 55014-1/A1:2009

EN 55014-2/A2:2008

EN 61000-3-2/A2:2009

EN 61000-3-3:2008

Type / Device description:

Power engraving tool PGG 15 A1

Date of manufacture (DOM): 04–2012

Serial number: IAN 73867

Bochum, 30.04.2012

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations in the course of

further development.

Spis zawartości

20

Strona się ładuje...

Parkside 73867 Operation and Safety Notes

Niniejsza instrukcja jest również odpowiednia dla

Parkside 73867 Operation and Safety Notes

w innych językach

Powiązane artykuły

Inne dokumenty