Classic Exhibits VK-2094 Setup Instructions
- Typ
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2094 - Magellan Miracle - General Layout
20’
10’
Plan View
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
Using You Set-up Instructions:
The Visionary Designs Set-up Instructions for Magellan displays are created
specifically for your configuration. They are laid out sequentially, including an
exploded view of the entire display and a logical series of detailed steps for
assembly. We encourage you to study the instructions before attempting to
assemble your exhibit.
THIS IS VERY IMPORTANT!
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in red).
Cleaning & Packing Your Display:
1) Use care when cleaning aluminum extrusions or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or counter tops, use mild cleansers and
a soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing materials. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Hex Key Tool
Typical Connection Typical Connection
Most visionary design exhibits can
be assembled with the supplied Hex
Key Tool. Occasionally, a flat head
screwdriver may be required.
Detail A: Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock and creates
a strong positive connection.
Numbered
Label
Detail B: Each extrusion contains a numbered label that
corresponds to set-up instructions. The label is located
within a groove of the extrusion (when possible). Visionary
Design labels contain Black numbers unless otherwise
specified.
Horizontal Connection
Detail C: A rectangular connection bar with plastic
T Knobs is inserted between two horizontal extrusions
joined end-to-end. Turn the knobs clockwise to tighten.
Do Not Overtighten.
www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
Part Number
1
2
3
4
5
6
7
8
9a/9b
10a/10b
11
12
Qty
1
1
1
1
1
1
1
1
1/1
1/1
1
1
Description
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
23”w Lower Horizontal Extrusion
23”w Upper Horizontal Extrusion
44”w Lower Horizontal Extrusion
44”w Upper Horizontal Extrusion
Backwall Support Leg Extrusion
Backwall Support Leg Extrusion
Steps
Unit can be assembled face down on the floor then lifted upright.
1)
Connect upper and lower vertical extrusions together [1 to 2, 3 to 4 and 5 to 6].
2) Connect horizontal extrusions together [9a to 9b and 10a to 10b].
3) Attach horizontal extrusions [7 and 8] between vertical assemblies [1/2 and 3/4].
4) Attach horizontal assemblies [9a/9b and 10a/10b] between vertical assemblies
[3/4 and 5/6].
5) Attach support leg extrusions [11 and 12] to back of verticals [1 and 5], see
leg attachment detail.
GREEN STAR indicates location
of connection lock with knob.
Knob
**Do not over tighten Knobs.**
RED STAR indicates location
of connection bar knob.
Turn Knob Clockwise
to Tighten Lock
Rear View of Display
**Do not over tighten Knobs.**
Knob
Knob
Connection
Bar
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
FRONT
VIEW
BACK
VIEW
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
Keep assembled
when shipping
Backside of backwall
Connect support leg to vertical
by placing lock into slot and
tighten with Allen Wrench.
Support Leg Attachment
(If accidentally removed from vertical)
1
2
3
4
5
6
9a
10a
7
8
11
9b
10b
A
A
A
B
B
12
Velcro at top of bar
Velcro at
top of bar
Velcro at bottom of bar
Velcro at left
& right of bar
Velcro at left
& right of bar
Velcro at
left of bar
Graphic Attachment
Apply graphic to back
of assembled backwall.
BACK VIEW
Velcro at
bottom of bar
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Part Number
13
14
15
16
17a/17b
18a/18b
19
20
21
Qty
1
1
1
1
1/1
1/1
1
1
1
Description
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
44”w Lower Horizontal Extrusion
44”w Upper Horizontal Extrusion
23”w Lower Horizontal Extrusion
23”w Upper Horizontal Extrusion
Backwall Support Leg Extrusion
Steps
1)
Connect upper and lower vertical extrusions together [13 to 14 and 15 to 16].
2) Connect horizontal extrusions together [17a to 17b and 18a to 18b].
3) Attach horizontal assemblies [17a/17b and 18a/18b] between vertical
assemblies [5/6 and 13/14].
4) Attach horizontal extrusions [19 and 20] between vertical assemblies
[13/14 and 15/16].
5) Attach support leg extrusions [21] to back of verticals [15], see
leg attachment detail.
GREEN STAR indicates location
of connection lock with knob.
Knob
**Do not over tighten Knobs.**
RED STAR indicates location
of connection bar knob.
Turn Knob Clockwise
to Tighten Lock
Rear View of Display
**Do not over tighten Knobs.**
Knob
Knob
Connection
Bar
5
6
13
14
15
16
17a
18a
19
20
12
17b
18b
A
A
A
B
B
21
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Velcro at top of bar
Velcro at
top of bar
Velcro at bottom of bar
Velcro at left
& right of bar
Velcro at
right of bar
Graphic Attachment
Apply graphic to back
of assembled backwall.
BACK
VIEW
BACK VIEW
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
Keep assembled
when shipping
Backside of backwall
Connect support leg to vertical
by placing lock into slot and
tighten with Allen Wrench.
Support Leg Attachment
(If accidentally removed from vertical)
Velcro at
bottom of bar
Backwall Assembly (Cont’d)
www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Backwall Workstation Assembly
Part Number
22
23
23a
24
25
Qty
2
2
2
2
2
Description
Base Plate
37.6”h Curved Vertical Extruaion
Oval Flange Plate
18.5”w Horizontal Extrusion
15.69”w Horizontal Extrusion
Steps
1)
Attach curved vertical [23] to base plate [22],
see Base Plate Attachment detail.
2) Attach horizontal extrusions [24 and 25] between
curved verticals [23] and backwall verticals [3 and 13]
where indicated.
3) Attach flange plate to top of verticals [23] as shown.
4) Place counter tops on assembled counter base,
see Counter Attachment detail.
Base Plate Attachment
22
23
24
25
Connect Vertical Extrusion to Base
Plate by placing lock into slot
and tighten with tool.
23a
Screw
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
22
23
24
25
23a
Screw
4
Monitor Mount
Monitor Mount Attachment
*
*
*
www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Pedestal Assembly - QTY. 2
Shelf
Counter
Part Number
26
27
28
29
30/30a
31
Qty
1
1
1
1
6
2
Description
37.5”h Vertical Extrusion
37.5”h Corner Extrusion
37.5”h Corner Extrusion
37.5”h Vertical Extrusion
11”w Horizontal Extrusion
24.875”w Horizontal Extrusion
Steps
1)
Attach horizontal extrusions [30 and 30a] between vertical
extrusions [26&27 and 28&29], see Top View for
extrusion orientation.
2) Attach curved horizontal extrusions [31] between
corner extrusions [27 and 28], placing insert between
curved horizontals.
Sintra Insert
26
27
28
29
31
31
30
Top View
26
27 28
29
31
30 30
30a
Lip for Shelf
Placement
Lip for Shelf
Placement
Steps (Cont’d):
3) Place hooks onto horizontal extrusions
where indicated, see Hook Attachment detial.
4) Set shelf atop hooks.
5) Set counter top atop assembled base.
30
30
30
30a
Extrusions 30a
have a lip for
floor to rest
upon. Lip
Extrusion Details:
www.classicexhibits.com
Step 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing Instruction - Case 1 of 4
Backwall Components
Top View of Each Level
Level 1 (Bottom) Level 2 Level 3 Level 4
Flange Plate
Backwall
Counter
#24
#25
#23
Base Plate
Horizontal Extrusions #9a&9b and 10a&10b
#11
#1
#2
#4
#7 & #8
#3
#6
#5
#12
Graphics
Halogen Lights
Setup Hardware
www.classicexhibits.com
Step 6
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing Instruction - Case 2 of 4
Backwall Components
Top View of Each Level
Level 1 (Bottom) Level 2 Level 3
Flange Plate
Backwall
Counter
#24
#25
#23
Base Plate
Horizontal Extrusions #17a&17b and 18a&18b
#19 & #20
#14
#16
#13
#15
#21
Graphics
Halogen Lights
Setup Hardware
www.classicexhibits.com
Step 7
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing Instruction - Case 3 of 4
Pedestal Components
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
Front Insert
Internal Shelf
(2)#21
Counter Top
Curved Extrusions # 22
Assembled
Pedestal
Side
Assembled
Pedestal
Side
www.classicexhibits.com
Step 8
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing Instruction - Case 4 of 4
Pedestal Components
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
Front Insert
Internal Shelf
(2)#21
Counter Top
Curved Extrusions # 22
Assembled
Pedestal
Side
Assembled
Pedestal
Side
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Classic Exhibits VK-2094 Setup Instructions
- Typ
- Setup Instructions
w innych językach
- English: Classic Exhibits VK-2094
Powiązane dokumenty
-
Classic Exhibits VK-2092 Setup Instructions
-
-
-
-
-
-
-
-
-