T&S 5F-8WLX08 Instrukcja instalacji

Marka: T&S

Model: 5F-8WLX08

Typ: Instrukcja instalacji

P/N: 098-013852-45 Rev.1

Date: 04-22-14

Drawn: TEH

Checked: DMH 04-23-14

Approved: JHB 04-28-14

Part Numbers

Equip Faucet and Pre-Rinse Unit Parts List

Ceramic Cartridge, Hot 013787-45

Ceramic Cartridge, Cold 013788-45

Handle Screw, Plain (10) 013849-45

Lever Handle Kit (includes color coded screws) 5-HDL-L

3/4-27UN Full Flow Laminar Outlet 014250-45

3” Rigid Gooseneck w/ Laminar Outlet 5SP-03

Nut, Swivel 013839-25

O-Ring, Swivel Piece (10) 013848-45

5-1/2” Swivel Gooseneck w/ Laminar Outlet 5SP-05

6” Swing Nozzle w/ Laminar Outlet 5SP-06

8” Swing Nozzle w/ Laminar Outlet 5SP-08

10” Swing Nozzle w/ Laminar Outlet 5SP-10

12” Swing Nozzle w/ Laminar Outlet 5SP-12

14” Swing Nozzle w/ Laminar Outlet 5SP-14

16” Swing Nozzle w/ Laminar Outlet 5SP-16

18” Swing Nozzle w/ Laminar Outlet 5SP-18

Check Valve, 20mm 013840-45

Check Valve Adapter, 1/2” BSP 010321-45

Overhead Spring, PRU 014068-45

Finger Hook Assembly 004R

Spray Valve Assembly, PRU 5SV

Bonnet Valve Assembly, PRU 002856-40

Bumper, Spray Face & Screw for PRU 5SV-RK

Hose Assembly, 44” 5HSE44

Hose Assembly, 68” 5HSE68

Hose Assembly, 84” 5HSE84

Hose Assembly, 96” 5HSE96

1/2” NPT Supply Nipple Kit (2) B-0425-M

1/2” NPT Male Elbow Kit (2) B-0230-K

1/2” NPT Female Eccentric Flange 00AA

Wall Bracket Assembly, 6” 013716-40

Riser, 18” 000369-40

Installation and

Maintenance

Instructions

EQUIP 8”

WALL-MOUNT

FAUCETS AND

PRE-RINSE UNITS

Limited One Year Warranty

Equip warrants to the original purchaser (other than for

purposes of resale) that such product is free from defects in

material and workmanship for a period of one (1) year from the

date of purchase. During this one-year warranty period, if the

product is found to be defective, Equip shall, at its option, repair

and/or replace it. To obtain warranty service, products must be

returned to...

Equip Foodservice Accessories

Attn: Warranty Repair Department

P.O. Box 1088, 2 Saddleback Cove

Travelers Rest, SC 29690

Shipping, freight, insurance, and other transportation

charges of the product to Equip and the return of repaired or

replaced product to the purchaser are the responsibility of the

purchaser. Repair and/or replacement shall be made within a

reasonable time after receipt by Equip of the returned product.

This warranty does not cover Items which have received

secondary  nishing or have been altered or modi ed after

purchase, or for defects caused by physical abuse to or

misuse of the product, or shipment of the products.

Any express warranty not provided herein, and any

remedy for Breach of Contract which might arise, is

hereby excluded and disclaimed. Any implied warranties

of merchantability or  tness for a particular purpose are

limited to one year in duration. Under no circumstances

shall Equip be liable for loss of use or any special conse-

quential costs, expenses or damages.

Some states do not allow limitations on how long

an implied warranty lasts or the exclusion or limitation

of incidental or consequential damages, so the above

limitations or exclusions may not apply to you. Speci c

rights under this warranty and other rights vary from

state to state.

Instructions Instructions

STEP 1

STEP 2

STEP 3

STEP 12

wall or

backsplash

B-0230-K

inlet kit

(available

separately)

Note: If unit is equipped with a rigid or swivel spout/gooseneck, install spout/

gooseneck  rst.

Rigid Gooseneck Installation:

1. Apply Te on tape, Loctite, or pipe joint compound to threads of gooseneck.

Thread gooseneck into outlet hole of body until joint is secure and

gooseneck faces desired direction.

Swing Nozzle/Swivel Gooseneck Installation:

Note: Silicon grease is applied to the interior swivel cavity of the body prior to

shipment. No additional grease is required.

2. Remove plastic cap from body outlet.

3. Insert nozzle/gooseneck into body cavity.

4. Tighten swivel lock nut using 1 5/16” wrench.

Faucet Body Installation:

5. Flush debris from water lines then shut o water supply.

6. Drill two holes, approximately 1” to 1-1/4” diameter, in wall or backsplash of

sink. Holes must be 8” between centers.

7. Install washers and nuts onto B-0230-K supply elbow kits, or similar ½” NPT

inlets, as far onto threaded ends as possible. Apply Te on tape or thread

sealant to ½“ NPT threads of these ends and pass through from back side of

wall openings. Thread elbow ends into the inlet holes of the faucet  anges

until the joints are secure.

8. Apply plumbers putty to faucet  ange mounting surfaces.

9. Secure faucet in place with supply elbow kit washers and nuts.

10. Connect water supplies to other end of elbows.

Pre-Rinse Installation:

11. After installation of the faucet body per steps 5 through 10, apply Te on

tape, Loctite, or pipe thread compound on the bottom of the riser. Slide

 nger hook onto riser before riser installation. Thread riser into outlet hole

of faucet body until joint is secured.

12. Install wall bracket and  nger hook, tightening all fasteners securely.

13. Rotate spring and hose assembly until they face desired direction.

14. Turn on water supplies and check for leaks.

T&S 5F-8WLX08 Instrukcja instalacji

Marka: T&S

Model: 5F-8WLX08

Typ: Instrukcja instalacji

ściągnij PDF

raport

w innych językach

English: T&S 5F-8WLX08 Installation guide

T&S 5F-8WLX08 Instrukcja instalacji

T&S 5F-8WLX08 Instrukcja instalacji

w innych językach

Inne dokumenty