Potter RD13 Residential Riser Instrukcja obsługi

Potter
Marka
Potter
Model
RD13 Residential Riser
Typ
Instrukcja obsługi
5401579 - REV B • 11/18 PAGE 1 OF 2
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com
RD13
Residential Riser with Capped
Flowswitch Port
Description
The RD13 Riser (with NPT connectors) is constructed from Listed
CPVC products suitable for re sprinkler services subject to the
limitations and installation requirements of Flameguard® CPVC
pipe and Spears® CPVC ttings. The RD13 Riser incorporates a
connection for a VSR-SG ow switch, gauge, and drain/test valve.
The connection for the VSR-SG owswitch is capped with a union
connection to facilitate the installation and removal of the switch in
conned spaces at a later date.
Installation
1. Using appropriate sealant, thread the female adapter on to the
main water supply. Then glue the riser assembly to the female
adapter. Pipe the drain connection to an adequate drain location
capable of handling the drain discharge. The riser can be mounted
in the horizontal or vertical position. The waterow switch
connection must be located on the top or on the side of the pipe
when installed in the horizontal position. This will prevent debris
from entering the throat of the waterow switch which could
interfere with proper operation.
2. Following CPVC manufacturer’s instructions for preparation and
gluing of CPVC piping systems, glue the main riser to the main
supply line for the sprinkler heads.
Note: All glued connections must be completed and cured before
the owswitch is installed.
3. A thread sealant shall be used in making threaded connections.
Teon® thread tape is the recommended sealant. Some thread
sealants other than Teon thread tape contain solvents or other
materials that may be damaging to CPVC. For other types of
thread sealants, which have been specically investigated and
conrmed to be “System Compatible”, refer to www.spearsmfg.
com. Attach gauge to riser. Apply Teon® tape to male tting of
gauge only. See Fig 1.
Riser Technical Specications
Dimensions See Fig 1
Service Pressure 175 PSI (12,07 BAR) - UL
Environmental
Limitations
Temperature range: 40°F-120°F (4.5°C-49°C)-
UL
Specications subject to change without notice.
Service Use
Automatic Sprinkler NFPA-13
One or two family dwelling NFPA-13D
Residential occupancy up to four stories NFPA-13R
National Fire Alarm Code NFPA-72
British Standard BS9251
Features
• Pre-assembled and pressure tested
• Available in 1”,1 1/4”, 1 1/2”, & 2” nominal pipe size models
• Female adapter ships loose so riser can be installed in a conned
space
• Fits in standard 2 x 4 construction walls
• Easily removable owswitch port cap for installation of VSR-
SG Flowswitch (VSR-SG not included)
• Includes 3 way valve to allow for calibration of pressure gauge
Installation must be performed by qualied personnel and in
accordance with all national and local codes and ordinances.
Do not over-tighten the union nut, hand tighten only. Use of a
wrench may cause damage to the union nut.
CAUTION
firealarmresources.com
5401579 - REV B • 11/18 PAGE 2 OF 2
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com
RD13
Residential Riser with Capped
Flowswitch Port
Dimensions
Fig 1
3 1/2” Gauge
(Shipped Loose)
1” NPT
Drain
Valve
Flowswitch
Port Cap
NPT Adaptor (Shipped Loose)
(See Chart Below)
*RD13 Risers (ASSEMBLED DIMENSIONS)
Riser
Size Model Number Part
Number
Dimension “A” Dimension “B” Dimension "C" Dimension "D" Dimension "E" Dimension "F"
(in.) (mm.) (in.) (mm.) (in.) (mm.) (in.) (mm.) (in.) (mm.) (in.) (mm.)
1" RD13 Riser w/ Cap 1” 1119068 19 483 15 3/4 400 18 457 14 5/8 371 12 1/4 311 10 1/2 267
1 1/4" RD13 Riser w/ Cap 1.25” 1119078 19 5/8 498 16 1/2 419 18 1/2 470 15 3/8 391 12 1/2 318 10 5/8 270
1 1/2" RD13 Riser w/ Cap 1.5” 1119088 N/A N/A 16 3/4 425 N/A N/A 15 5/8 397 12 3/4 324 10 3/4 273
2" RD13 Riser w/ Cap 2” 1119098 N/A N/A 18 1/4 464 N/A N/A 16 7/8 429 13 3/8 340 11 1/8 283
Ordering Information
Ordering Information
Nominal Pipe
Size Model Part Number
1" RD13 Riser w/ Cap 1” 1119068
1 1/4" RD13 Riser w/ Cap 1.25” 1119078
1 1/2" RD13 Riser w/ Cap 1.5” 1119088
2" RD13 Riser w/ Cap 2” 1119098
Optional: VSR-SG, stock no. 1144460
Gauge and NPT Adapter shipped loose in box.
A
B
C
D
E
F
firealarmresources.com
  • Page 1 1
  • Page 2 2

Potter RD13 Residential Riser Instrukcja obsługi

Potter
Marka
Potter
Model
RD13 Residential Riser
Typ
Instrukcja obsługi
ściągnij PDF
raport

w innych językach

Inne dokumenty