Parkside PSSA 18 A1 Original Instructions Manual

CORDLESS SABRE SAW PSSA 18 A1

AKKU-SÄBELSÄGE

Originalbetriebsanleitung

CORDLESS SABRE SAW

Translation of the original instructions

A

KUMULATOROWA PIŁA SZABLASTA

Tłumaczenie oryginalnej instrukcji obsługi

A

KU PILA OCASKA

Překlad originálního provozního návodu

AKUMULÁTOROVÁ PÍLA

Preklad originá lneho návodu na obsluhu

A

KUMULATORSKA SABLJASTA ŽAGA

Prevod originalnega navodila za uporabo

AKKUS KARDFŰRÉSZ

Az originál használati utasítás fordítása

IAN 104447

104447_par_Akku-Saebelsaege_cover_PL_HU_SI_CZ_SK.indd 2 11.02.15 17:04

GB Translation of the original instructions Page

PL Tłumaczenie oryginalnej instrukcji obsługi Strona

HU Az originál használati utasítás fordítása Oldal

SI Prevod originalnega navodila za uporabo Stran

CZ Překlad originálního provozního návodu Strana

SK Preklad originálneho návodu na obsluhu Strana

DE / AT / CH Originalbetriebsanleitung Seite

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funk cjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funk cióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

104447_par_Akku-Saebelsaege_cover_PL_HU_SI_CZ_SK.indd 3 11.02.15 17:04

4

21

40

113

95

77

59

1 23 4

431

56 78

8

9

10

11

1414a

11

13

14

12

4

GB

Content

_LBIntroduction ............................4

Intended Use ................................ 4

General Description ......................5

Scope of delivery .............................. 5

Overview ......................................... 5

Function Description .......................... 5

Technical Data ..............................5

Notes on Safety ...........................6

Symbols ........................................... 6

General safety instructions for power

tools ................................................ 7

Special Safety Directions for the device 9

Correct handling of the battery charger .11

Charging the battery ..................12

Removing/inserting the battery ......... 12

Recharging the battery ..................... 12

Used batteries ................................ 13

Assembly ...................................13

Installing/changing the blade ........... 13

Operation ..................................13

Switching on and off ....................... 14

Adjusting the base plate .................. 14

Switching on/off the oscillating function 14

Checking the charge status of the re-

chargeable battery .......................... 14

Practical tips ................................... 15

Cleaning/Maintenance ...............16

Cleaning ........................................ 16

General maintenance ...................... 16

Storage ......................................16

Waste Disposal/

Environmental Protection ...........16

Guarantee .................................17

Repair Service ............................18

Service-Center ............................18

Importer .................................... 18

Spare Parts/Accessories .............19

Trouble Shooting ........................ 20

Translation of the original EC

declaration of conformity .........133

Exploded Diagram ...................137

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product. During production,

this equipment has been checked for qual-

ity and subjected to a nal inspection. The

functionality of your equipment is therefore

guaranteed.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied. Keep this

manual safely and in the event that

the product is passed on, hand over

all documents to the third party.

Intended Use

The device is suitable for light and medium

sawing through wood, plastic and plaster-

board. If a separately available saw blade

is used, it is also possible to saw through

metal. The device is not suitable for com-

mercial use.

Any other use that is not explicitly ap-

proved in these instructions may result in

damage to the equipment and represent a

serious danger to the user.

The operator or user is responsible for ac-

cidents or damage to other people or their

property. The manufacturer is not liable

for damages caused by unspecied use or

incorrect operation.

5

GB

General Description

The illustration of the principal

functioning parts can be found

on the front and back foldout

pages.

Scope of delivery

Carefully unpack the trimmer and check

that it is complete. Dispose of the packag-

ing material correctly.

- Cordless reciprocating saw

- Saw blade

- Rechargeable battery

- Charger

- Instruction Manual

Overview

1 Saw blade

2 Footplate

3 Saw blade retainer

4 Chuck ring

5 Adjustment button for the base

plate

6 Rotary switch for oscillating

movement

7 Ventilation slit

8 On/off switch

9 Switch lock

10 Rear handle

11 Rechargeable battery

12 Unlock button - rechargeable bat-

tery

13 Front handle

14 Charger

Function Description

The cordless sabre saw is a hand-held pen-

dulum jigsaw with a saw blade that moves

back and forth. The oscillating motion can

be switched on to improve the progress of

the sawing action.

Read the sections below to learn more

about each operating element’s function.

Technical Data

Appliance

Motor voltage ............................. 18 V

Idling speed n

0

............ 0-3000 min

-1

(rpm)

Protection category ...........................IPX0

Stroke ..............................approx. 20 mm

Max. cutting depth

Wood .................................... 100 mm

Metal ........................................ 8 mm

Weight (incl. accessories) ...............2.5 kg

Sound pressure level

(L

PA

) .................. 85.73 dB (A), K

PA

=3 dB

Sound power level

(L

WA

) ................ 96.73 dB(A); K

WA

=3 dB

Vibration (a

h

) ..........................................

Sawing boards .................. 13.88 m/s

2

Sawing wood beams .......... 17.01 m/s

2

K=1,5 m/s

2

Battery (Li-Ion) ....................PAP 18-1.5 A1

Number of battery cells......................... 5

Nominal voltage ........................ 18 V

Capacity ..................................... 1.5 Ah

Charging time ...................... approx. 1 h

Recharger ............................. JLH-H150-18

Nominal consumption .................... 40 W

Voltage input .........100-240 V~, 50-60 Hz

Voltage output ..............18 V

1500 mA

Protection class .................................

II

Protection category ...........................IPX0

6

GB

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity.

Technical and optical changes may be

undertaken in the course of further develop-

ment without notice. All dimensions, refer-

ences and information in this instruction

manual are therefore not guaranteed. Legal

claims made on the basis of the instruction

manual can therefore not be considered as

valid.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning:

The vibration emission value may

differ during actual use of the

power tool from the stated value de-

pending on the manner in which the

power tool is used.

Safety precautions aimed at protect-

ing the user should be based on

estimated exposure under actual

usage conditions (all parts of the op-

erating cycle are to be considered,

including, for example, times during

which the power tool is turned off

and times when the tool is turned on

but is running idle).

Notes on Safety

This section details the basic safety instruc-

tions for working with the appliance.

Symbols

Symbols on the Equipment

Caution!

Read through the instruction manual

carefully.

Wear eye protection.

Wear ear protection.

Wear breathing protection.

Wear cut-resistant gloves.

Keep other people away from the

device.

Keep hands away from the sawing

area.

Remove the battery from the device

before carrying out any work.

Electrical appliances must not be

disposed of with the domestic

waste.

Symbols on the battery

Do not dispose of bat-

teries in household

waste, re or water.

7

GB

Do not subject the battery to strong

sunlight over long periods and

do not leave it on a heater (max.

45°C).

Take batteries to an old battery

collection point where they will

be recycled in an environmentally

friendly manner.

Symbols on the recharger

Caution!

Read the operating instructions be-

fore charging.

The recharger is for indoor use only.

T2A

Miniature fuse

Protection class II

Electrical appliances must not be

disposed of with the domestic

waste.

LED display

while charging.

Symbols in the manual

Warning symbols with in-

formation on damage and

injury prevention.

Instruction symbols (the instruction

is explained at the place of the ex-

clamation mark) with information on

preventing damage.

Help symbols with information on

improving tool handling.

General safety instructions

for power tools

WARNING! Read all safety

directions and instructions.

Omissions in the compliance with

safety directions and instructions

can cause electrical shock, re

and/or severe injuries.

Retain all safety directions and in-

structions for future use.

The term „power tool“ in the warnings refers

to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

• Keepworkareacleanandwell

lit. Cluttered or dark areas invite ac-

cidents.

• Donotoperatepowertoolsin

explosive atmospheres, such as

inthepresenceofammable

Iiquids, gases or dust. Power tools

create sparks which may ignite the dust

or fumes.

• Keepchildrenandbystanders

away while operating a power

tool. Distractions can cause you to

lose control.

2) ELECTRICAL SAFETY

• Powertoolplugsmustmatch

the outlet. Never modify the

plug in any way. Do not use

any adapter plugs with earthed

(grounded) power tools. Unmodi-

ed plugs and matching outlets will

reduce risk of electric shock.

• Avoidbodycontactwithearthed

or grounded surfaces, such as

pipes, radiators, ranges and re-

8

GB

frigerators. There is an increased risk

of electric shock if your body is earthed

or grounded.

• Donotexposepowertoolsto

rain or wet conditions. Water

entering a power tool will increase the

risk of electric shock.

• Donotabusethecord.Never

use the cord for carrying, pull-

ing or unplugging the power

tool. Keep cord away from

heat, oil, sharp edges or moving

parts. Damaged or entangled cords

increase the risk of electric shock.

• Whenoperatingapowertool

outdoors, use an extension cord

suitable for outdoor use. Use of a

cord suitable for outdoor use reduces

the risk of electric shock.

• Ifoperatingapowertoolina

damp location is unavoidable,

use a residual current device

(RCD) protected supply. Use of an

RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

• Stayalert,watchwhatyouare

doing and use common sense

when operating a power tool.

Do not use a power tool while

youaretiredorundertheinu-

ence of drugs, alcohol or medi-

cation. A moment of inattention white

operating power tools may result in

serious personal injury.

• Usepersonalprotectiveequip-

ment. Always wear eye protec-

tion. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

• Preventunintentionalstarting.

Ensure the switch is in the off-po-

sition before connecting to power

sourceand/orbatterypack,

pickinguporcarryingthetool.

Carrying power tools with your nger on

the switch or energising power tools that

have the switch on invites accidents.

• Removeanyadjustingkeyor

wrench before turning the pow-

er tool on. A wrench or a key left

attached to a rotating part of the power

tool may result in personal injury.

• Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear

loose clothing or jewellery. Keep

your hair, clothing and gloves away

from moving parts. Loose clothes, jew-

ellery or long hair can be caught in

moving parts.

• If devices are provided for the

connection of dust extraction

and collection facilities, ensure

these are connected and prop-

erly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

• Do not force the power tool. Use

the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the

switch does not turn it on and

off. Any power tool that cannot be

controlled with the switch is dangerous

and must be repaired.

• Disconnect the plug from the

power source and/or the bat-

terypackfromthepowertool

beforemakinganyadjust

9

GB

-ments, changing accessories, or

storing power tools. Such preven-

tive safety measures reduce the risk of

starting the power tool accidentaIly.

• Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions

to operate the power tool. Power

tools are dangerous in the hands of

untrained users.

• Maintainpowertools.Checkfor

misalignment or binding of mov-

ingparts,breakageofpartsand

any other condition that may af-

fect the power tool’s operation. If

damaged, have the power tool repaired

before use. Many accidents are caused

by poorly maintained power tools.

• Keep cutting tools sharp and

clean. Properly maintained cutting

tools with sharp cutting edges are less

Iikely to bind and are easier to control.

• Use the power tool, accessories

and tool bits etc. in accordance

withtheseinstructions,tak-

ingintoaccounttheworking

conditionsandtheworktobe

performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) CAREFUL HANDLING AND USE

OF BATTERY DEVICES

• Chargethebatteriesonlyin

chargers that are recommended

by the manufacturer. Risk of re if a

charger that is suitable for a specic type

of battery is used with other batteries.

• Inthepowertools,useonlythe

batteries designed for the pur-

pose. The use of other batteries may

result in injuries and risk of re.

• Keeptheunusedbatteryaway

frompaperclips,coins,keys,

nails, screws and other small

metal objects, which could cause

bridging of the contacts. A short

circuit between the battery contacts

may cause burns or re.

• Ifusedincorrectly,liquidmay

leakfromthebattery.Avoid

contact with this. In the event of

accidental contact, rinse off with

water. If the liquid gets into eyes, seek

medical assistance. Leaking battery u-

id may cause skin irritations or burns.

6) SERVICE

• Have your power tool serviced

byaqualiedrepairpersonus-

ing only identical replacement

parts. This will ensure that the safety

of the power tool is maintained.

Special Safety Directions for

the device

1) SPECIAL SAFETY INSTRUCTIONS

FOR RECIPROCATING SAWS

• Holdtheelectrictoolbythein-

sulated gripping surfaces when

performingworkinwhichthe

cutting tool may come into con-

tact with hidden wiring. Contact

with a live wire can also cause a

charge in metal parts of the device and

result in an electric shock.

• Keephandsawayfromthesaw-

ing area. Do not reach under-

neaththeworkpiece.Upon contact

with the blade there is a risk of injury.

• Onlywhentheelectrictoolis

turned on should the sawing

blade be moved against the

10

GB

workpiece.There is a risk of kickback

if the tool insert jams in the work piece.

• Makesurethatthebaseplate

is securely placed against the

workpieceduringsawing.The

saw blade can tilt and lead to loss of

control over the power tool.

• Afteryouhavenishedwork,

turn the power tool off and do

not pull the saw blade out of the

cut until it has come to a stand-

still. In this way you will avoid any

kickback and can safely put down the

power tool.

• Useonlyundamagedsaw

blades in perfect condition. Bent

or blunt blades can break, adversely

affect the cut or cause kickback.

• Donotbrakethesawblade

after switching the device off

by applying side pressure. The

saw blade may be damaged, break or

cause a kickback.

• Tightenthematerialrmly.Donot

supporttheworkpiecebyhand

or foot. Do not touch any objects

or the ground with the saw run-

ning. There is a risk of kickback.

• Usesuitabledetectorsinorder

tondhiddensupplylinesor

askthelocalutilitycompany.

Contact with electrical cables can lead

to electric shock and re, contact with

a gas pipe can result in an explosion.

Damage to a water pipe can lead to

property damaged and electric shock.

• Holdthepowertooltightlywith

bothhandswhileworkingand

ensure a secure footing. The power

tool is guided more securely with both

hands.

• Securetheworkpiece. A work

piece that is retained with clamping

devices or a vice is held more securely

than with your hand.

• Waituntilthepowertoolhas

stopped before placing it down.

The tool insert can tilt and lead to loss

of control over the power tool.

• Donotsawanymaterials(e.g.

lead-based paints and coatings

or materials containing asbes-

tos) whose dust can be harmful.

2) SPECIAL SAFETY DIRECTIONS FOR

BATTERY-OPERATED TOOLS

• Ensurethatthedeviceis

switched off before inserting

the battery. Inserting a battery into

a power tool that is switched on may

result in accidents.

• Rechargethebatteriesindoors

only because the battery charg-

er is designed for indoor use

only. Risk of electric shock.

• Toreducetheelectricshockhaz-

ard, unplug the battery charger

from the mains before cleaning

the charger.

• Donotsubjectthebatteryto

strong sunlight over long pe-

riods and do not leave it on a

heater. Heat damages the battery

and there is a risk of explosion.

• Allowahotbatterytocoolbe-

fore charging.

• Donotopenupthebatteryand

avoid mechanical damage to the

battery.Riskofshortcircuitand

fumes may be emitted that ir-

ritate the respiratory tract. Ensure

fresh air and seek medical assistance in

the event of discomfort.

• Donotusenon-rechargeable

batteries. This could damage the ap-

pliance.

11

GB

3) RESIDUAL RISKS

Even if properly operating and handling

this electric tool, some residual risks will

remain. Due to its construction and build,

this electric tool may present the following

hazards:

a) Lung damage, if suitable respiratory

protection is not worn;

b) Cuts

c) Ear damage if working without ear pro-

tection.

d) Damage to your health caused by

swinging your hands and arms when

operating the appliance for longer pe-

riods of time or if the unit is not held or

maintained properly.

Warning! During operation, this

electric tool generates an electro-

magnetic eld which, under certain

circumstances, may impair the

functionality of active or passive

medical implants. To reduce the risk

of serious or lethal injuries, we rec-

ommend that persons with medical

implants consult their doctor and the

manufacturer of their medical im-

plant before operating the machine.

Correct handling of the bat-

tery charger

• This appliance can be used by

persons with reduced physical,

sensory or mental capabili-

ties or lack of experience and

knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved. Children

shall not play with the appli-

ance.

• To charge the battery, use only

the charger supplied. Risk of re

and explosion. This ensures that the

safety of the device is maintained.

• Beforeeachuse,checkthe

charger, cable and plug and

have them repaired by quali-

edprofessionalsandonlywith

original parts. Do not use a de-

fective charger and do not open

it up yourself. This ensures that the

safety of the device is maintained.

• Connect the charger only to a

socketwithanearth.Ensure

that the mains voltage matches

thespecicationsonthecharger

rating plate. Risk of electric shock.

• Disconnect the charger from the

mains before closing or opening

connection to the battery / power

tool / device. This ensures that the bat-

tery and charger are not damaged.

• Keep the charger clean and

away from wet and rain. Do not

use the charger outdoors. Dirt

and the entry of water increase the risk

of electric shock.

• Operate the charger only with

the appropriate original bat-

teries. Charging other batteries may

result in injuries and risk of re.

• Avoid mechanical damage to

the charger. This can result in inter-

nal short circuits.

• Do not operate the charger on a

combustible surface (e.g. paper,

textiles). Risk of re due to heating

during charging.

• Ifthepowercableforthis

equipment is damaged, it must

be replaced by the manufac-

turer, a customer service agent

of the same or a similarly quali-

edpersoninordertoprevent

12

GB

hazards.

• Donotchargenon-rechargeable

batteries in the charger. This could

damage the appliance.

Charging the battery

Do not expose the battery to

extreme conditions such as

heatorimpact.Riskofinjury

from escaping electrolytic so-

lution!Aftereye/skincontact,

rinse the affected areas with

water or a neutraliser and

consult a doctor.

Charge the battery in a dry

room only. Prior to attach-

ingthecharger,checkthat

the battery’s outer surface is

cleananddry.Thereisarisk

ofinjuryduetoelectricshock.

Only use the charger from the pack-

age to charge the battery. Mind not

to charge the appliance for more

than 1 hour at a time. If you do, the

battery and the appliance may be

damaged and longer charging times

would be a waste of energy. Exces-

sive charging will void the warranty.

• Charge the battery before the rst time

of use. Do not briey charge the bat-

tery several time in a row.

• If a fully recharged battery lasts for con-

siderably shorter operating times, the

battery is used up and needs to be re-

placed. Only use an OEM spare battery

available from our Customer Service.

• Always take heed of the applicable

safety instructions as well as the envi-

ronmental protection regulations and

information.

• The warranty excludes all defects

caused by improper handling.

Removing/inserting the

battery

1. To remove the battery (11) from

the appliance, press the release

button (12) on the battery and

pull out the battery.

2. To insert the battery (11), place

it on the guide track and push it

back into the appliance. It will

audibly snap in.

Recharging the battery

Charge the battery (11) when only

the red LED of the charge indicator

(11a) is lit (see “Checking the bat-

tery charge status”).

1. Remove the battery (11) from the

appliance, as necessary.

2. Slide the rechargeable battery

(11) onto the charger (14). It

locks into place audibly.

3. Plug the battery charger (14) into

a mains outlet.

4. When the battery is fully re-

charged unplug the battery charg-

er (14) from the mains.

5. Press the release button (

10) on

the battery (11) and pull the battery

out of the battery charger (14).

Overview of the LED indicators

(14a) on the charger (14):

green LED ashes:

Charger is connected to the

mains without a battery.

red LED lights up:

Charging.

13

GB

green LED lights up:

Charging is completed.

green LED ashes:

The battery voltage is < 12.5V,

battery is pre-charged for

30min.

LEDs ash red and green:

Defective battery installed,

no charging.

LEDs light up in red and green:

Rechargeable battery is too cold

or too hot.

After a cooling or heating period,

charging starts automatically.

Used batteries

• If a fully recharged battery lasts for

considerably shorter operating times,

the battery is used up and needs to be

replaced. Only use an OEM battery

pack replacement available from our

Customer Service.

• Always take heed of the applicable

safety instructions as well as the envi-

ronmental protection regulations and

information (see “Waste Disposal and

Environmental Protection”).

Assembly

Only insert the rechargeable

battery when the device is com-

pletely assembled. If the device

is switched on accidentally,

there is a danger of injury.

Installing/changing the

blade

Always wear protective gloves

when handling the saw blade in

order to avoid cutting yourself.

 Caution,riskofInjury!

- Do not use any blunt or bent

blades or blades which are dam-

aged in any other way.

- Always insert a suitable saw

blade.

An overview of appropriate blades

can be found in “Spare Parts/Ac-

cessories”.

Installing the blade:

1. Turn the chuck ring (4) in the

direction of the arrow

and

insert the shank of the saw blade

(1) all the way into the slot of the

saw blade holder (3).

2. To lock, turn the chuck ring (4)

back to the starting position.

3. Check that the saw blade is se-

cure by pulling on it.

Removing the saw blade:

4. Turn the chuck ring (4) in the

direction of the arrow

and

pull the blade out of the saw

blade holder.

For certain work, the saw blade

can also be inserted after turning

through 180°.

Operation

 Whenworkingwiththede-

vice, always wear suitable

clothing and appropriate pro-

tective equipment.

Prior to each use it must be

ensured that the device is

workingcorrectly.

Personal protective equip-

ment and a fully functional

devicereducetheriskofinju-

14

GB

ries and accidents.

After the device has been

switched off, the blade con-

tinues moving for some time.

Do not touch the moving

blade and do not attempt to

brakeit.Dangerofinjury!

Switching on and off

Ensure your stance is stable and

hold the device tightly with both

hands and away from your body.

Before switching the device on,

ensure it is not in contact with the

work piece.

Switching on:

1. Ensure that the battery (11) is in-

serted (see “Removing/inserting

the battery”).

2. Press the switch lock (9) and the

on/off switch (8), then release

the switch lock (9).

3. By using the on/off switch (8) you

can progressively control the stroke

rate.

Gentle pressure: low stroke rate.

Greater pressure: higher stroke rate.

The on/off switch cannot be

locked.

Switching off:

4. Release the on/off switch (8).

Adjusting the base plate

To adapt to the work piece, the base plate

can be adjusted and swivelled to 4 posi-

tions.

1. Press the adjusting button (5).

2. The base plate (2) can now be ad-

justed to the desired position. It can

now be felt locking into place.

3. The base plate (2) can be pivoted

by applying light pressure.

Switching on/off the oscillat-

ing function

To improve the progress of the sawing pro-

cess, an oscillating motion can be switched

on.

Sawing without oscillation:

- For thin, hard work pieces such as

wooden boards.

- In order to achieve cleaner cut edges.

Sawing with oscillation:

- For processing work pieces with medium

and soft strength, such as soft and hard

wood, tree wood, insulation material.

Switching on the oscillating

function:

1. Turn the rotary switch (6) to posi-

tion “1”.

Switching off the oscillating

function:

2. Turn the rotary switch (6) to posi-

tion “0”.

Checking the charge status of

the rechargeable battery

The state of charge display (11a) indicates

the state of charge of the battery (11).

Press the button (11b) on the bat-

tery (11). The state of charge of

the battery is displayed by illumi-

nating the 3-colour LED lights of

the state of charge display (11a).

All LEDs are on: Battery is fully

charged.

15

GB

Red and yellow LEDs are on:

Battery has a residual charge

(< 90 %).

Red LED lights up: Battery is

empty, please charge.

Practical tips

Wear gloves when handling the

saw blade. In this way, you avoid

injury from cuts.

 Caution:Riskofinjuryand

damage to property!

- Do not use any blunt or bent

blades or blades which are dam-

aged in any other way.

- Before sawing the work piece,

check for hidden foreign objects

such as nails, screws. These must

be removed.

- Always insert a suitable saw

blade.

- Secure the work piece with the

aid of clamping devices on the

workbench.

- Apply only as much pressure as

is required for sawing. If there is

excessive pressure, the sawing

blade may bend and break.

- Switch the device off immedi-

ately if the sawing blade jams.

Spread the saw cut out and pull

the blade out carefully.

- Always stand to the side of the

saw when working.

- Always make sure that the work-

place is well ventilated.

- Avoid over-stressing the device

while working.

Conventional sawing:

1. Turn the device on. Before switching

the device on, ensure it is not in contact

with the work piece.

2. Place the base plate on the work piece.

3. Cut with a uniform forward motion. You

can saw horizontally (see

), diago-

nally or vertically (see

).

4. After completion of the work, rst re-

move the blade from the saw cut and

then switch the device off.

Plunge sawing:

Plunge cuts are technically more demand-

ing and harbour a greater risk. Only per-

form this work if you are familiar with this

technique.

Plunge cuts may only be car-

ried out in soft materials such

as wood or plasterboard

and with short blades (max.

length 150 mm). There is a

riskofkickbackandperson-

al injury.

1. Place the front edge of the base plate (2)

on the work piece so that the saw blade

(1) does not touch the work piece.

2. Turn the device on and let the saw blade

(1) slowly plunge into the work piece.

3. When the work piece depth has been

cut through, continue sawing as usual.

Flush separation:

With elastic bi-metal saw blades (see

spare parts/accessories) you can separate

water pipes, for example, ush to the wall.

 Makesurethatthebladeis

always longer than the pipe

diameter.Thereisariskof

kickbackandpersonalinjury.

16

GB

Cleaning/Maintenance

Remove the battery from the

device before carrying out

anyworkortransportingit.

If the device is switched on

accidentally, there is a dan-

ger of injury.

Repair and servicing work not

described in this manual should

always be carried by our Service

Centre. Use only original parts.

Always wear protective gloves

when handling the saw blade in

order to avoid cutting yourself.

The following cleaning and servicing

should be done regularly. This will ensure a

long and reliable service life.

Cleaning

Do not spray the appliance

with water and do not im-

merse it in water. Electric

shockhazard!

• Keep clean the ventilation slots, motor

housing and handles of the appliance.

Use a damp cloth or a brush.

Do not use cleaning agents or solvents.

You may otherwise irreparably damage

the appliance.

• Clean the saw blade holder with a

brush or by blowing out with com-

pressed air. To do this, remove the saw

blade from the device.

General maintenance

• Prior to every use, check the appliance

for obvious defects such as loose, worn

or damaged parts.

• Check covers and safety devices for

damages and correct installation. Re-

place as necessary.

• Replace a blunt or bent blade or one

which has been damaged in some

other way.

Storage

• Store the device in a dry place well out

of reach of children.

• Remove the battery before storing the

unit for longer periods of time (e.g. hi-

bernation).

• Store the battery only in a partially

charged state. The state of charge

should be 40 – 60 % over a longer stor-

age period (two LED lights of the char-

ge status indicator (

11a) light up).

• During a longer storage period, check

the state of charge of the battery and

recharge if necessary roughly every

3months.

• In order to keep the battery well

charged, avoid exposing the appliance

to extreme heat or cold in storage.

• Store the equipment between 10° C

and 25° C. During storage, avoid ex-

treme cold or heat so the battery does

not lose power.

Waste Disposal/

Environmental Protection

Remove the battery from the device and

take the device, battery, accessories and

packaging for environmentally friendly

recycling.

Machines do not belong with do-

mestic waste.

17

GB

Do not dispose of batteries in house-

hold waste, re (risk of explosion) or

water. Damaged batteries may dam-

age the environment and your health

if toxic fumes or liquids leak out.

• Return the unit to a recycling centre.

• Dispose of batteries in discharged condi-

tion. We recommend covering the pole

with adhesive tape to prevent a short

circuit. Do not open up the battery.

• Dispose of batteries in accordance with

the local regulations. Take batteries to

an old battery collection point where

they will be recycled in an environmen-

tally friendly manner. For information

about this, ask your local waste man-

agement company or our service centre.

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These statu-

tory rights are not restricted by our guaran-

tee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect occurs

within three years of the date of purchase

of this product, we will repair or replace –

at our choice – the product for you free of

charge. This guarantee requires the defec-

tive equipment and proof of purchase to be

presented within the three-year period with

a brief written description of what consti-

tutes the defect and when it occurred.

If the defect is covered by our guarantee, you

will receive either the repaired product or a

new product. No new guarantee period be-

gins on repair or replacement of the product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced

in accordance with strict quality guidelines

and conscientiously checked prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee does

not extend to cover product parts that are

subject to normal wear and may therefore

be considered as wearing parts (e.g. saw

blade, battery) or to cover damage to

breakable parts (e.g. switches).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

18

GB

Processing in Case of Guarantee

To ensure quick handling of you issue,

please follow the following directions:

• Please have the receipt and identica-

tion number (IAN 104447) ready as

proof of purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

• After consultation with our customer ser-

vice, a product recorded as defective

can be sent postage paid to the service

address communicated to you, with the

proof of purchase (receipt) and speci-

cation of what constitutes the defect

and when it occurred. In order to avoid

acceptance problems and additional

costs, please be sure to use only the ad-

dress communicated to you. Ensure that

the consignment is not sent carriage

forward or by bulky goods, express or

other special freight. Please send the

equipment inc. all accessories supplied

at the time of purchase and ensure ad-

equate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the

guarantee can be carried out by our ser-

vice branch, which will be happy to issue

a cost estimate for you. We can handle

only equipment that has been sent with ad-

equate packaging and postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 104447

Importer

Please note that the following address is

not a service address. Please initially con-

tact the service centre specied above.

GrizzlyToolsGmbH&Co.KG

Stockstädter Straße 20

63762 Großostheim, Germany

www.grizzly-service.eu

GB

19

GB

Spare Parts/Accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone (see

“Service-Center” Page 18). Please have the order number mentioned below ready.

Position Position Description Use Order No.

instruction exploded

manual drawing

1 19 Wood saw blade for wood, plastic, 1380 0221

(HCS 150 mm/6 TPI*) plasterboard

11 16 Battery 18 V, 1,5 Ah 8000 1161

14 21 Charger EU, 1,5 Ah 8000 1082

Optionally available:

Description Use Order No.

Metal saw blade

for metal sheets,

proles and tubes

1380 0222

Battery 18 V, 2,6 Ah 8000 1162

Charger EU, 2,6 Ah 8000 1086

* HCS = High Carbon Steel, steel with high carbon content

TPI = Teeth per inch

We recommend using the battery only with the battery charger supplied.

More blades with a universal shank are commercially available for any

purpose.

20

GB

Trouble Shooting

Problem Possible cause Corrective action

Appliance

won‘t start

Battery (

11) discharged Recharge battery (see „Charging“)

Battery (

11) not inserted Insert battery (see „Operation“)

Switch lock (

11) has not

been operated properly

Switch on (see "Operation")

On/Off switch (

7) defec-

tive

Send in to Service Centre for repair

Intermittent op-

eration

Internal loose contact

Send in to Service Centre for repair

On/Off switch (

7) defec-

tive

Poor sawing

performance

Saw blade unsuitable

for the work piece to be

worked on

Insert a suitable saw blade

Saw blade blunt Insert a new saw blade

Incorrect sawing speed Adjust sawing speed

Low battery power

Charge battery (

11) (see "Charg-

ing process")

Saw blade

quickly be-

comes blunt

Saw blade unsuitable

for the work piece to be

worked on

Insert a suitable saw blade (see "In-

stallation")

Too much pressure applied Reduce the pressure

Sawing speed too high Reduce the sawing speed

Strona jest ładowana ...

Parkside PSSA 18 A1 Original Instructions Manual

Parkside PSSA 18 A1 Original Instructions Manual

w innych językach

Powiązane dokumenty

Inne dokumenty