Sony KLV-20SR3 Instrukcja obsługi

Operating Instructions

GB

Before operating the TV, please read the “Safety Information”

section of this manual. Retain this manual for future reference.

R

LCD Colour TV

Инструкция по эксплуатации

RU

Перед тем как включить телевизор, просим Вас ознакомиться

с разделом "Общие правила техники безопасности"

настоящей инструкции. Сохраняйте настоящую инструкцию

на будущее.

Instrukcja obsługi

PL

Przed przystąpieniem do eksploatacji telewizora należy

zapoznać się z rozdziałem "Informacje dotyczące

bezpieczeństwa" w niniejszej instrukcji. Prosimy o zachowanie

niniejszej instrukcji do wglądu w przyszłości.

Manual de Instruções

PT

Antes de utilizar o televisor, por favor leia a secção “Informação

sobre segurança” deste manual. Guarde este manual para

futuras consultas.

KLV-20SR3

2-067-275-12 (1)

3

GB

Introduction

• Thank you for choosing this Sony product.

• Before operating the TV, please read this manual thoroughly and retain it for future reference.

• Symbols used in the manual:

Table of Contents

Introduction .......................................................................................................................................................... 3

Quick Start Guide................................................................................................................................................. 4

Safety Information.............................................................................................................................................. 10

Precautions .........................................................................................................................................................13

Overview & Installation

Checking the Accessories Supplied.................................................................................................................... 14

Overview of Remote Control Buttons................................................................................................................ 15

Overview of the TV Buttons and side Connectors.............................................................................................17

Overview of the TV Indicators...........................................................................................................................18

Inserting Batteries into the Remote Control.......................................................................................................18

Removing the Rear Cover ..................................................................................................................................19

Connecting the Aerial and VCR......................................................................................................................... 20

Adjusting the viewing angle of the TV .............................................................................................................. 21

First Time Operation

Switching on the TV and Automatically Tuning ............................................................................................... 22

TV Functions

Introducing and Using the Menu System .......................................................................................................... 24

The Picture Adjustment menu ..................................................................................................................... 25

The Sound Adjustment menu.......................................................................................................................27

The Features menu........................................................................................................................................ 28

The Set Up menu.......................................................................................................................................... 30

The Manual Programme Preset menu.......................................................................................................... 32

Other Functions

Sleep Timer ........................................................................................................................................................34

Picture Freeze.....................................................................................................................................................34

Teletext..................................................................................................................................................................35

Additional Information

Connecting Equipment to the TV........................................................................................................................36

Viewing pictures from equipment connected to the TV......................................................................................38

Technical Specifications......................................................................................................................................39

Troubleshooting...................................................................................................................................................40

• Buttons shaded white on the remote control show you the

buttons you have to press to follow the sequence of the

instructions.

• Informs you of the result of the instructions.

• Important information.

• Information on a feature.

• 1,2... Sequence of instructions.

Table of Contents

4

Quick Start Guide

This section will help you to:

-Insert batteries into the remote control,

-Remove the rear cover,

-Connect an aerial and VCR,

-Automatically tune the TV,

1 Mains Lead (Type C-6):

2 Batteries (AA size):

1 Remote

control

(RM-Y1108):

Quick Start Guide

Checking the Accessories supplied

1

5

GB

Inserting batteries into the remote control

2

SONY CORPORATION JAPAN/4

S

ON

Y CO

R

PO

R

A

T

IO

N

JA

PA

N

/4

Make sure you insert the supplied batteries using the correct polarities.

Always remember to dispose of used batteries in an environmental friendly way.

Quick Start Guide

6

Removing the rear cover

3

When you connect the cables, remove the rear cover of the TV set. Be sure to attach the rear cover back on the TV

set after you finish connecting the cables.

Removing the rear cover

Hold the rear cover as illustrated below and pull off one side of the lower part of the cover towards you first. Then,

detach the upper part of the cover from the TV set.

Attaching the rear cover

Hold the rear cover as illustrated below, fitting the four detents on the rear cover into the corresponding holes on the

TV set, then push the rear cover back on to the TV set.

It is not necessary to attach the rear cover if you install a wall-mount bracket SU-W210 (optional

accessory).

Quick Start Guide

7

GB

or

VCR

Connecting the aerial and VCR

4

Make sure to connect the aerial before the Scart.

For more details regarding VCR connection, refer to “Connecting Equipment to the TV” on page 36.

Quick Start Guide

8

The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose

the language of the menu screen 2) choose the country in which you are going to operate the TV, 3) search and

store all available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast)

appear on the screen.

However, if you need to change any of these settings at a later date, you can do that by selecting the appropriate

option in the (Set Up menu) or by pressing and holding the Auto Start Up button on the top of TV set

for more than three seconds, see page 17.

Switching on the TV and automatically tuning

5

1 Connect the TV plug to the mains socket (220-240V

AC, 50Hz).

2 The first time that the TV set is connected, it is usually

turned on. If the TV is off, press the on/off button to

turn on the TV.

The first time you switch on the TV, a Language menu

appears automatically on the TV screen.

3 Press the V, v, B or b buttons on the remote control to select your

language, then press the

OK button to confirm your selection. From

now on all the menus will appear in your chosen language.

4 The Country menu appears automatically. Press the v or V button

to select the country in which you are using the TV. Press the

OK

button to confirm your selection.

• If the country in which you want to use the TV set does not

appear in the list, select “-” instead of a country.

• To avoid wrong teletext characters for cyrillic languages we

recommend selecting Russia if your own country does not

appear in the list.

Country

Select country

United Kingdom

Ireland

Nederland

België/Belgique

Luxembourg

France

Italia

Schweiz/Suisse/Svizzera

Deutschland

Österreich

Quick Start Guide

9

GB

5 The Auto Tuning menu appears on the screen. Press the OK

button to select Yes.

6 The TV starts to automatically search and store all

available broadcast channels for you.

This procedure could take some minutes. Please be patient

and do not press any buttons, otherwise automatic tuning

will not be completed.

If no channels were found during the auto tune process, a

message appears automatically on the screen asking you to

connect the aerial. Check the aerial connection (refer to

page 20). Press the

OK button to restart the auto tuning

process.

7 After all available channels are captured and stored,

the Programme Sorting menu automatically appears

on the screen enabling you to change the order in

which the channels are stored.

a) If you wish to keep the broadcast channels in the tuned order,

go to step 8.

b) If you wish to store the channels in a different order:

1 Press the v or V button to select the programme

number with the channel (TV Broadcast) you wish

to move. Press the

b button.

2 Press the v or V button to select the new

programme number position for your selected channel

(TV Broadcast). Press the

OK button to store

The selected channel now moves to its new

programme position and the other channels move

accordingly.

3 Repeat steps b)1 and b)2 if you wish to change

the order of the other channels.

8 Press the MENU button to remove the menu from the screen

Your TV set is now ready for use

Auto tuning

Programmes found:

No channel found.

Please connect aerial

Confirm

Programme Sorting

Exit:

MENU

01

02

03

04

05

06

07

08

09

10

11

TVE

TVE2

TV3

C33

C27

C58

S02

S06

C44

C47

C48

Programme Sorting

Exit:

MENU

01

02

03

04

05

06

07

08

09

10

11

TVE

TVE2

TV3

C33

C27

C58

S02

S06

C44

C47

C48

01 TVE

Do you want to start

automatic tuning?

Ye s No

Quick Start Guide

10

Safety Information

Mains lead

Unplug the mains lead when

moving the TV. Do not move

the set with the mains lead

plugged in. It may damage the

mains lead and result in fire or

electric shock. If the set has been dropped or

damaged, have it checked immediately by qualified

service personal.

Medical institution

Do not place this TV set in a

place where medical

equipment is in use. It may

cause malfunction of medical

instruments.

Damage requiring service

If the surface of the display cracks, do not touch it until

you have unplugged the mains lead. Otherwise electric

shock may result.

Ventilation

Leave space around the TV set. Otherwise, adequate air-

circulation may be blocked causing overheating which

may cause fire or damage the TV set.

LCD screen

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are

effective, black dots may appear or bright points of

light (red, blue or green) may appear constantly on the

LCD screen. This is a structural property of the LCD

panel and is not a malfunction.

• Do not expose the LCD screen surface to the sun.

Doing so may damage the screen surface.

• Do not push or scratch the front filter, or place objects

on top of the TV set .The image may be uneven or the

LCD panel may be damaged.

• If the TV set is used in a cold place, a smear may occur

in the picture or the picture may become dark. This

does not indicate a failure. These phenomena disappear

as the temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when the TV set is in

use. This is not a malfunction

Carrying

Before carrying the TV set, disconnect all the cables

from the TV set.

Fluorescent lamp

This TV set uses a special fluorescent lamp as its

light source. If the screen image becomes dark,

flickers or does not appear, the fluorescent lamp has

run down and should be replaced. For replacement,

consult qualified service personnel.

Adjusting the viewing angle of the TV set

When adjusting the angle, hold the stand with your

hand so that it does not come loose or fall off.

Be careful not to catch your fingers between the TV

set and the stand.

10 cm

Leave at least this

much space.

30 cm

10 cm

Never install the unit as follows:

Air circulation

is blocked

Wall

Safety Information

11

GB

Power Sources

Overloading

This TV set is designed to operate

on a 220-240V AC supply only.

Take care not to connect too

many appliances to the same

mains socket as this could result

in fire or electric shock.

Mains lead protection

Pull out the mains lead by the

plug. Do not pull on the mains

lead itself.

Wiring

Unplug the mains lead when wiring cables. Be sure to

unplug the mains lead for your safety, when hooking up.

Cleaning

Clean the mains plug regularly. If the

plug is covered with dust and it picks up

moisture, its insulation may deteriorate

and result in fire. Unplug the mains plug

and clean it regularly.

When not in use

For environmental and safety

reasons, it is recommended that

the TV set is switched off when

not in use - not left in standby

mode. Disconnect from the

mains.

Mains

Do not use a poor fitting mains socket. Insert

the plug fully into the mains. If it is loose, it

may cause arcing and result in fire. Contact

your electrician to have the mains socket

changed.

Moisture

Do not touch the mains lead with a wet

hand. If you plug/unplug the mains lead

with a wet hand, it may cause electric

shock.

Lightning storms

For your own safety, do not touch

any part of the TV set, mains lead

or aerial lead during lightning

storms.

Mains lead

If you damage the mains lead, it

may result in fire or electric

shock.

• Do not pinch, bend, or twist the

cable excessively. The core

lines may be bared or cut,

causing a short - circuit which

may in fire or electric shock.

• Do not convert or damage the

mains lead.

• Do not put anything heavy on the mains lead. Do not

pull the mains lead.

• Keep the mains lead away from heat sources.

• Be sure to grasp the plug when disconnecting the

mains lead.

• If the mains lead is damaged, stop using it and ask your

dealer or Sony service centre to exchange it.

Electric shock

Do not touch the TV set with wet hands. Doing so may

cause electric shock or damage the TV set.

Corrosion

If you use this set near the seashore, salt may corrode

metal parts of the TV set and cause internal damage or

fire. It may also shorten the life of the TV set. Steps

should be taken to reduce the humidity and temperature

of the area where the set is located.

Cable wiring

Take care not to catch your feet on the cables. It may

damage the TV set.

Installation

Do not install optional components too close to the TV

set. Keep optional components at least 30 cm away from

the TV set. If a VCR is installed in front or at the right

side of the TV set, the picture may distort.

Heat

Do not touch the surface of the TV. It remains hot, even

after the TV has been turned off for some time.

Oils

Do not install TV set in restaurants that use oil. Dust

absorbing oil may enter into the TV set and damage TV

set.

Water and moisture

Do not use the TV set near water – for example, near a

bathtub or shower room. Also, do not expose to rain,

moisture or smoke. This might result in fire or electric

shock. Do not use the TV set where insects may enter.

Disposal of the TV set

• Do not dispose of the TV set with general household

waste.

• The LCD contains a small amount of liquid crystal and

mercury. The fluorescent tube used in the TV set also

contains mercury. Follow your local ordinances and

regulations for disposal

continued...

Safety Information

12

Installation and moving

Ventilation

Never cover the ventilation holes in the

cabinet. It may cause overheating and

result in fire. Unless proper ventilation is

provided, the TV set may gather dust and

get dirty. For proper ventilation, observe

the following:

• Do not install the TV set turned backward or sideways.

• Do not install the TV set turned over or upside down.

• Do not install the TV set on a shelf or in a closet.

• Do not place the TV set on a rug or bed.

• Do not cover the TV set with cloth, such as curtains, or

items such as news papers, etc.

Outdoor use

Do not install this TV set

outdoors. If the TV set is exposed

to rain, it may result in fire or

electric shock. If the TV set is

exposed to direct sunlight, the TV

set may heat up and it may

damage the TV set.

Vehicle or ceiling

Do not install this TV set in a vehicle.

Bumping of the vehicle may cause the

set to fall down and cause injury. Do

not hang this TV set from the ceiling.

Ships and other vessels

Do not install this TV set in a ship

or vessel. If the TV set is exposed

to seawater, it may cause fire or

damage the TV set.

Servicing

Do not open the cabinet. Entrust

the TV set to qualified service

personnel only.

To prevent the TV set from falling

Place the TV set on a secure, stable stand. Do not hang

anything on the TV set.

Moisture and flammable objects

• Do not let this TV set get wet.

Never spill liquid of any kind on

the TV set. If any liquid or solid

object does fall through, do not

operate the TV set. It may result in electric shock or

damage to the TV set. Have it checked immediately by

qualified personnel.

• To prevent fire, keep flammable objects or naked

lights (e.g. candles) away from the TV set.

Ventilation holes

Do not insert anything in the ventilation

holes. If metal or something flammable

enters, it may result in fire or electric shock.

Protruding location

Do not install the TV set in protruding locations. If you

install the TV set in the following locations, it may result

in injury.

• Do not install the TV set in a location where the TV set

protrudes, such as on or behind pillar.

• Do not install the TV set in a location where you might

bump your head on it.

Placement

Never place the TV set in hot,

humid or excessively dusty places.

Do not install the TV set where it

may be exposed to mechanical

vibrations.

Cleaning the Screen Surface

The screen surface is finished with a special coating to

prevent strong light reflections. Be sure to observe the

following precautions to avoid the damaging the finish.

• To remove dust from the screen surface, wipe gently with

a soft cloth. If dust is persistent, wipe with a soft cloth

slightly moistened with a diluted mild detergent

solution. You can wash and repeatedly use the soft cloth.

• Never use any type of abrasive path, alkaline/acid

cleaner, scouring powder, or strong solvent such as

alcohol, benzine or thinner.

Cleaning

Unplug the mains lead when cleaning this TV set. If not,

it may result in electric shock.

Recommended place for the TV set

Place the TV Set on a stable, level

surface. Otherwise, the TV set may fall

and cause injury.

Safety Information

13

GB

Precautions

On viewing the TV comfortably

• To view the TV comfortably, the recommended viewing position is from four to seven times of the screen’s

vertical length away from the TV set.

• View the TV in a moderate light room, as viewing the TV in poor light taxes your eyes. Watching the screen

continuously for long periods of time can also tax your eyes.

On installing the TV set

• Do not install the TV in places subject to extreme temperature, for example in direct sunlight, or near a radiator,

or heating vent. If the TV set is exposed to extreme temperature, the TV set may heat up and it may cause

deformations of the casing or cause the TV set to malfunction.

• To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot

lighting directed down from the ceiling.

• The TV set is not disconnected from the mains when the switch is in Off position. To disconnect the set

completely, pull the plug from the mains.

On volume adjustment

• Adjust the volume so as not to trouble neighbours. Sound carries very easily at night time. Therefore, closing the

windows or using headphones is suggested.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

On handling the remote control

• Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote control in a location near a heat source, or in a place subject to direct sunlight, or in a

damp room.

On cleaning the cabinet

• Be sure to unplug the mains lead before cleaning.

• Clean the cabinet with a soft cloth lightly dampened. Do not use any type of abrasive pad, alkaline cleaner,

scouring powder or solvent, such as alcohol or benzine, or antistatic spray.

• Note that material deterioration or screen coating degradation may occur if the TV is exposed to a volatile solvent,

such as alcohol, thinner, benzine or insecticide, or if prolonged contact is maintained with rubber or vinyl

materials.

• The ventilation holes can accumulate dust over a period of time and the accumulated dust may make the cooling

function less effective. To prevent this, we recommend removing the dust periodically (once a month) using a

vacuum cleaner.

On handling and cleaning the screen surface

To avoid screen degradation, follow the points mentioned below. Do not push on or scratch with hard objects, or

throw anything at the screen. The screen may be damaged.

• Be sure to unplug the mains lead before cleaning.

• Do not touch the TV after operating continuously for along period as the display panel becomes hot.

• We recommend that the screen surface is touched as little as possible.

• Clean the screen with a soft cloth lightly moistened. Cleaning with dirty cleaning cloth may result in damage to

the TV set. Never use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. This type

of contact may result in damage to the screen surface.

Safety Information

14

Overview & Installation

Checking the Accessories supplied

1 Mains Lead (Type C-6):

2 Batteries (AA size):

1 Remote

control

(RM-Y1108):

Overview & Installation

15

GB

Overview of Remote Control Buttons

1 Muting the Sound: Press this button to mute the sound from the TV. Press it

again to cancel.

2 TV I/ -

Switching the TV to the standby mode:

Press this button to temporarily turn off the TV and switch it to standby mode (the

(Standby/Sleep) indicator on the TV lights up in red). Press again to switch on

the TV from standby mode.

• To save energy, we recommend switching the TV off completely when

the TV is not in use.

• If no signal is received or no operation is performed in the TV mode for

15 minutes, the TV automatically switches to standby mode.

3

Picture Freeze: Press this button to freeze the picture. For more details refer to

"Picture Freeze" on page 34

4

Turning on the Sleep Timer Function: Press this button to set the TV to

automatically switch to standby mode after a specified time period. For more

details, refer to "Sleep Timer Function" on page 34.

5

Selecting the input source: Press this buttons repeatedly until the input

symbol of the desired source appears on the screen.

6 0 - 9

Selecting Channels: Press these buttons to select channels. For

double-digit channel numbers, enter the second digit within 2.5 seconds.

7

Displaying on-screen information: Press this button to display all on-screen

indicators. Press it again to cancel.

8

Watching Last Channel Selected: Press this button to watch the last channel

selected (the last channel watched for at least five seconds).

9

Fastext: In Teletext mode, these buttons can be used as Fastext buttons. For

more details see page 35

q; Selecting a sound effect: Press this button repeatedly to change the sound

effect. For details on different sound effects refer to page 27

qa Selecting the Picture Mode / Adjusting the Brightness Of Teletext

Pages.

a)

In normal TV mode: Press this button repeatedly to change the picture

mode. For more details, refer to "Picture Adjustment" on page 25.

b) In Teletext mode: Press this button repeatedly to change the brightness of

Teletext pages.

Overview & Installation

1

3

2

4

5

7

8

9

q;

6

qa

qs

qd

qf

qg

qh

qk

qj

continued...

16

The buttons with green symbols (except for (Power/Standby)) are also used for Teletext operations. For

more details refer to "Teletext" on page 35.

qs V / v / B / b / OK Buttons:

a)

When the menu is displayed: use these buttons to operate the menu

system. For more details, refer to "Introducing and Using the Menu

System" on page 24.

b) When the menu is turned off: press OK to show an overview of all TV

Channels. Then press

V or v to select the channel and press OK to watch

the selected channel.

qd Selecting the TV mode: Press this button to switch off Teletext or video

input.

qf Selecting Teletext: Press this button to switch on Teletext. For more

details, refer to "Teletext" on page 35.

qg MENU - Displaying the menu system: Press this button to display the

menu on the screen. Press it again to remove the menu from the screen.

qh 2

+/- Adjusting the TV volume: Press these buttons to adjust the

volume of the TV.

qj

PROG +/- Selecting Channels: Press these buttons to select the next or

previous channel.

qk

Selecting screen format: Press this button to view programmes in 16:9

mode. Press again to return to 4:3 mode.

Overview & Installation

1

3

2

4

5

7

8

9

q;

6

qa

qs

qd

qf

qg

qh

qk

qj

17

GB

Overview of the TV Buttons and side Connectors

3

o3

Power On / OffVolume control

(+/-)

Programme Up or

Down (selects TV

channels)

Picture Freeze press this button to

freeze the picture. For more details

refer to “Picture Freeze” on page 34.

Auto Start Up press and hold this

button for three seconds to start the

Auto Start Up sequence. For more

details refer to “Switching On the

TV and Automatically Tuning” on

page 22.

Selecting Input Source

for more details refer to

“Viewing pictures from

equipment connected to

the TV” on page 38.

Overview of the TV Buttons

Overview of the side Connectors

S Video Input

jack

Audio Input

jacks

Video Input

jack

Headphones

jack

Overview & Installation

18

Overview & Installation

Overview of the TV indicators

Inserting Batteries into the Remote Control

Make sure you insert the supplied batteries using the correct polarities.

Always remember to dispose of used batteries in an environmental friendly way.

To operate the remote

control, point it towards

this receiver.

Lights up in green when the

TV is switched on.

• Lights up in red when

the TV is in standby

mode.

• Flashes red when a

button is pressed on the

remote control.

• Lights up in red when

the sleep timer is set.

For more details, refer

to “Sleep Timer” on

page 34.

SONY CORPORATION JAPAN/4

S

O

N

Y

C

O

R

PO

R

A

TIO

N

JA

P

AN

/4

19

GB

Overview & Installation

Removing the Rear Cover

When you connect the cables, remove the rear cover of the TV set. Be sure to attach the rear cover back on the TV

set after you finish connecting the cables.

Removing the rear cover

Hold the rear cover as illustrated below and pull off one side of the lower part of the cover towards you first. Then,

detach the upper part of the cover from the TV set.

Attaching the rear cover

Hold the rear cover as illustrated below, fitting the four detents on the rear cover into the corresponding holes on the

TV set, then push the rear cover back on to the TV set.

It is not necessary to attach the rear cover if you install a wall-mount bracket SU-W210 (optional

accessory).

20

Connecting the Aerial and VCR

or

VCR

Overview & Installation

Make sure to connect the aerial before the Scart.

For more details regarding VCR connection, refer to “Connecting Equipment to the TV” on page 36.

21

GB

Adjusting the viewing angle of the TV

You can adjust the angle to avoid the reflection of light and get a better view of the TV set.

When adjust the angle, hold the stand with your hand so that it does not come loose or fall off.

Be careful not to catch your fingers between the TV and the stand.

Backward direction

Horizontal direction

10º

75º 75º

Overview & Installation

Strona jest ładowana ...

Sony KLV-20SR3 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Sony KLV-20SR3 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty