HP LaserJet 9050 Printer series Skrócona instrukcja obsługi

HP LaserJet 9040/9050

Getting Started Guide

Začínáme

Alapvet tudnivalók kézikönyve

Wprowadzenie

English

HP LaserJet 9040/9050 printer

Getting Started Guide

Development Company, L.P.

Reproduction, adaptation, or translation

without prior written permission is prohibited,

except as allowed under the copyright laws.

The information contained herein is subject

to change without notice.

Publication number

Q3721-90938

Edition 1, 02/2005

The only warranties for HP products and

services are set forth in the express warranty

statements accompanying such products and

services. Nothing herein should be construed

as constituting an additional warranty.

HP shall not be liable for technical or editorial

errors or omissions contained herein.

Trademark Credits

Microsoft



, Windows



, and Windows NT



are U.S. registered trademarks of Microsoft

Corporation.

UNIX



is a registered trademark of

The Open Group.

All other products mentioned herein may be

trademarks of their respective companies.

ENWW Contents 3

English

Printer Setup

Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Prepare printer location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Check package contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Locate printer parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remove internal packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Install accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Install print cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connect printer cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting a parallel cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting to Ethernet 10/100TX network (for the HP LaserJet 9040n/9050n and the

HP LaserJet 9040dn/9050dn). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Change the control panel overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connect power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Configure the control panel display language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Load Tray 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Load Trays 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Print a configuration page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Install printing software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installing Windows printing software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Installing Macintosh printing software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Verify printer setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Customer support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Warranty and regulatory information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Hewlett-Packard limited warranty statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

HP’s Premium Protection Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

HP Software License Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

FCC regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4 Printer Setup ENWW

Introduction

Congratulations on your purchase of the HP LaserJet 9040/9050 printer. This series of printers is

available in the following configurations.

HP LaserJet 9040/9050 printer

The HP LaserJet 9040/9050 printer (product number Q7697A/Q3721A) comes standard with

64 megabytes (MB) of random-access memory (RAM), wide-format printing, and two 500-sheet

trays.

Note Only the HP LaserJet 9040/9050 printer requires an optional enhanced input/output

(EIO) card to connect to a network.

HP LaserJet 9040n/9050n printer

The HP LaserJet 9040n/9050n printer (product number Q7698A/Q3722A) comes standard with

128 MB of RAM, wide-format printing, two 500-sheet trays, a 100-sheet multipurpose tray

(Tray 1), and an embedded HP Jetdirect print server.

HP LaserJet 9040dn/9050dn printer

The HP LaserJet 9040dn/9050dn printer (product number Q7699A/Q3723A) comes standard

with 128 MB of RAM, wide-format printing, two 500-sheet trays, a 100-sheet multipurpose tray

(Tray 1), an embedded HP Jetdirect print server, and a duplex printing accessory (for printing on

both sides of paper).

Installation checklist

This guide will help you set up and install your new printer. For correct installation, please

complete each section in order:

WARNING! The printer is heavy. HP recommends that four people move it to avoid injury to you and damage

to the printer.

● Unpack the printer steps 1-4

● Install the printer steps 5-13

● Install printing software step 14

● Verify printer setup step 15

ENWW Prepare printer location 5

English

Step 1. Prepare printer location

Shipping box space requirements

Make sure that your building has a door or receiving area large enough for delivery of the

shipping box. The approximate dimensions of the shipping box are as follows:

911 x 790 mm deep x 1036 mm high (36 x 31 inches deep x 41 inches high).

Unpacking space requirements

Before removing the plastic wrapping from the shipping box, make sure that you have enough

space to remove the contents from the shipping box, and then lift the product off its shipping

pallet. HP recommends at least 3.1 meters (10 feet) of space around the shipping box to remove

all of the shipping materials.

Removing the printer from the shipping box

See the graphics on the shipping box for information about how to remove the printer from the

shipping box.

WARNING! The printer is heavy. HP recommends that four people move it to avoid injury to you and damage

to the printer.

6 Printer Setup ENWW

Printer size

Prepare a location for the printer that allows for these physical and environmental requirements:

HP LaserJet 9040/9050 printer dimensions (top and side views)

633 mm (24.9 inches)

353 mm

(13.9 inches)

638 mm (25.1 inches)

600 mm (23.6 inches)

368 mm

(17.8 inches)

353 mm

(13.9 inches)

638 mm (25.1 inches)

406 mm

(16 inches)

406 mm

(16 inches)

ENWW Prepare printer location 7

English

1

The smaller measurement is the space that is required to extend the output device with the

attachment bar still attached to the latch under optional Tray 4. The larger measurement is the

space that is required to remove the output device from the product. The additional space

allows enough clearance to remove the attachment bar from the latch under optional Tray 4.

HP LaserJet 9040/9050 with typical output device, Tray 4, and Tray 1 installed (top and

side views) to show maximum dimensions

1001 mm

(39.4 inches)

1036 mm (40.8 in)

2591 mm (102 inches) to extend output

device; 2705 mm (106.5 inches) to

remove output device

1

2591 mm (102 inches) to extend output

device; 2705 mm (106.5 inches) to

remove output device

1

8 Printer Setup ENWW

Printer weight (without print cartridge)

● HP LaserJet 9040/9050 printer: 63.5 kg (140 lb)

● HP LaserJet 9040n/9050n printer: 69.4 kg (153 lb)

● HP LaserJet 9040dn/9050dn printer: 76.2 kg (168 lb)

Location requirements for the printer

● A level area on a hard surface,

preferably a floor without carpet

● Space allowance around the

printer

● A well-ventilated room

● No exposure to direct sunlight

or chemicals, including

ammonia-based cleaning

solutions

● Adequate power supply (For

the 110 V model, a dedicated

15 A circuit is recommended;

for the 220 V model, a

dedicated 8 A circuit is

recommended)

● A stable environment—no

abrupt temperature or humidity

changes

● Relative humidity 20% to 80%

● Room temperature 10°C to

32.5°C (50°F to 91°F)

ENWW Check package contents 9

English

Step 2. Check package contents

Package contents

Note The HP LaserJet 9040n/9050n printer includes Tray 1 and an embedded HP Jetdirect print server

(not shown).

The HP LaserJet 9040dn/9050dn printer includes Tray 1, an embedded HP Jetdirect print server

(not shown), and a duplex printing accessory (duplexer; not shown).

power cord

printer

control panel

overlay

print

cartridge

printer software

CD-ROM

(including use

guide)

printer documentation

(this manual)

face-up output bin

optional

Tray 4

optional

Tray 1

10 Printer Setup ENWW

Step 3. Locate printer parts

The following illustrations give the location and names of the important printer parts.

Printer parts (front and rear views)

1 Face-up output bin

2 Control panel

3 Tray 2

4 Power switch

5 Tray 1

6 Standard output bin

(face-down bin)

7 Front door

8 Tray 3

9 EIO slots (2)

10 Security lock port

11 Power cord

connector

12 Local area network (LAN)

connector (RJ-45) (for the

HP LaserJet 9040n/9050n

and 9040dn/9050dn)

13 Parallel B cable connector

14 HP Jet-Link connector (for

paper-handling accessory)

1

2

6

8

3

4

7

10

11

12

13

9

5

14

ENWW Remove internal packaging 11

English

Step 4. Remove internal packaging

CAUTION The printer contains orange shipping tape and internal packaging to prevent damage during

shipping. You must remove all shipping materials and internal packaging in order for the printer

to function correctly.

To remove internal packaging

1 Remove all orange packing material from the exterior of the printer and remove any

cardboard or styrofoam material that is not orange.

2 Remove all orange packing material from the standard output bin and the protective film from

the control panel display.

3 Open the left door and pull straight back on the shipping tape to remove the two fuser

shipping locks (as shown by the diagram on the printer). Make sure that the fuser levers are

in the lock position.

4 Open the trays, remove any orange packing material, and close the trays.

5 Open the front door and remove the orange packing tape at the front transfer roller area and

on the lock lever for the print cartridge. Close the front door.

Note Save all packing material. You might need it to repack the printer at a later date.

12 Printer Setup ENWW

Step 5. Install accessories

WARNING! This printer weighs approximately 63.5 kg (140 lb). HP recommends that four people move it to

avoid injury to you and damage to the printer.

Install any paper-handling accessories that you purchased with the printer or separately. Use the

installation instructions that are packaged with the accessories. The instructions might be on a

CD-ROM.

Install duplexer

Note If you purchased an output device (the multifunction finisher, the 3,000-sheet stacker, the 3,000-

sheet stacker/stapler, or the 8-bin mailbox) along with a duplexer and an input device (Tray 4 and/

or Tray 1), install the duplexer and the input device(s) before trying to install the output device.

Refer to the installation instructions that are included with the duplexer. The instructions might be

on a CD-ROM.

Duplexer

Note After you have installed the duplexer, return to this guide to complete the printer setup.

Install input device(s)

Refer to the installation instructions that are included with the input device(s). The instructions

might be on a CD-ROM.

Tray 1 and Tray 4

ENWW Install accessories 13

English

Note After you have installed the input device(s), return to this guide to complete the printer setup.

Install output device

Install any output device that you purchased. After the device is installed, go to step 6.

Refer to the installation instructions that are included with the output device. The instructions

might be on a CD-ROM.

.

Output devices

8-bin mailbox

Multifunction finisher

3,000-sheet stacker/stapler

or 3,000-sheet stacker

14 Printer Setup ENWW

Step 6. Install print cartridge

Use this procedure to install the print cartridge. If toner gets on your clothing, wipe it off with a dry

cloth and wash the clothing in cold water. Hot water sets toner into fabric.

To install the print cartridge

1 Before removing the print cartridge from its packaging, set the print

cartridge on a sturdy surface. Gently slide the print cartridge out of

the packaging.

CAUTION

To prevent damage to the print cartridge, use two hands when handling

the cartridge.

Do not expose the print cartridge to light for more than a few minutes.

Cover the print cartridge when it is outside of the printer.

2 Gently rock the print cartridge from front to back to distribute the

toner evenly inside the cartridge. This is the only time that you need

to rock the cartridge.

3 Open the front door on the printer.

4 Rotate the green lever downward to the unlock position.

5 Hold the cartridge so that the arrow is on the left side of the

cartridge. Position the cartridge as shown, with the arrow on the left

side pointing toward the printer, and align the cartridge with the

printing guides. Slide the cartridge into the printer as far as it will go.

Note

The print cartridge has an internal pull tab. The printer automatically

removes the pull tab after the print cartridge is installed and the product

is turned on. The print cartridge makes a loud noise for several seconds

when the product removes the pull tab. This noise occurs with new print

cartridges only.

6 Press the button on the green lever, and turn the lever clockwise to

the lock position.

7 Close the front door.

1

5

3

4

6

7

ENWW Connect printer cables 15

English

Step 7. Connect printer cables

The printer can connect to a computer using a parallel cable, or to the network using an optional

HP Jetdirect print server.

For printers equipped with the embedded HP Jetdirect print server, a network cable connection

is provided through a 10/100TX (RJ-45) connector. The printer also has a connector for an

HP Jet-Link Connector.

Location of interface ports

Parallel B

connector (Parallel)

Local area network

(LAN) connector

(RJ-45)

HP Jet-Link

connector (for paper-

handling accessory)

16 Printer Setup ENWW

Connecting a parallel cable

Use a parallel cable if you want to connect the printer directly to a computer.

To ensure reliability, use an IEEE-1284 bidirectional B-type parallel cable. These cables are

clearly marked with “IEEE-1284.” Only IEEE-1284 cables support all of the advanced printer

features.

To connect a parallel cable

1 Make sure that the printer power cord is not connected to an outlet.

2 Connect the parallel cable to the printer parallel port. Press the

locking release levers while connecting the cable.

Note

If installing the cable is difficult, make sure you have the correct cable.

3 Connect the other end of the cable to the proper connector on the

computer.

2

3

ENWW Connect printer cables 17

English

Connecting to Ethernet 10/100TX network (for the HP LaserJet

9040n/9050n and the HP LaserJet 9040dn/9050dn)

Use the RJ-45 connector if you want to connect the printer to an Ethernet 10/100TX network.

To connect to Ethernet 10/100TX network

1 Make sure that the printer power cord is not connected to an outlet.

2 Connect a network cable to the embedded HP Jetdirect print server

that is installed in the printer.

3 Connect the other end of the cable to the network port.

2

3

18 Printer Setup ENWW

Step 8. Change the control panel overlay

The control panel comes with an English overlay installed. If necessary,

use the procedure below to change the control panel overlay to one

included in the box.

To change the overlay

1 Insert your fingernail or a thin, rigid object in back of the overlay and

lift up.

2 Gently lift the overlay up and backward to move it away from the

printer.

3 Position the new overlay over the control panel. Align the ends of

the overlay with the holes on the control panel and slide the overlay

in.

4 Snap the overlay firmly onto the control panel. Ensure that the

overlay is flat against the control panel.

1

2

3

4

5

Strona jest ładowana ...

HP LaserJet 9050 Printer series Skrócona instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

HP LaserJet 9050 Printer series Skrócona instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty