Parkside PBS 600 A1 Operation and Safety Notes

Kategoria
Szlifierki elektryczne
Typ
Operation and Safety Notes

Ten podręcznik jest również odpowiedni dla

PÁSOVÁ BRUSKA
Pokyny pro obsluhu a bezpečnostní pokyny
eklad originálního provozního návodu
PÁSOVÁ BRÚSKA
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
BELT SANDER
Operation and Safety Notes
Translation of original operation manual
BANDSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
SZLIFIERKA TAŚMOWA
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
TRAČNI BRUSILNIK
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
PBS 600 A1
4
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB Operation and Safety Notes Page 5
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 15
SI Navodila za upravljanje in varnostna opozorila Stran 25
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 35
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 45
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 55
A
B C
D E F
8
12
2 3 4
13
11
1
67 5
9
10
5 GB
Table of contents
Introduction
Proper use .....................................................................................................................Page 6
Features and equipment ...............................................................................................Page 6
Included items ...............................................................................................................Page 6
Technical information ...................................................................................................Page 7
General safety advice for electrical power tools
1. Workplace safety .....................................................................................................Page 7
2.
Electrical safety ........................................................................................................Page 7
3. Personal safety .........................................................................................................Page 8
4.
Careful handling and use of electrical power tools ..............................................Page 8
Safety advice for belt sanders.....................................................................................Page 9
Preparing for use
Tensioning / changing the sanding belt ......................................................................Page 10
Advice on use ...............................................................................................................Page 10
Vacuum dust extraction ................................................................................................Page 10
Operation
Switching on and o....................................................................................................Page 11
Selecting the correct rotational speed and sanding belt ..........................................Page 11
Using the device in a fixed mounting ..........................................................................Page 12
Tips and tricks ...............................................................................................................Page 12
Maintenance and cleaning ........................................................................Page 12
Service centre .......................................................................................................Page 12
Warranty ..................................................................................................................Page 12
Disposal ......................................................................................................................Page 13
Declaration of Conformity / Manufacturer..................................Page 13
6 GB
Introduction
Belt sander PBS 600 A1
Introduction
Please make sure you familiarise yourself
fully with the way the device works before
you use it for the first time and that you
understand how to handle electrical power tools
correctly. To help you do this please read the accom-
panying operating instructions. Keep these instructions
in a safe place. If you pass the device on to anyone
else, please ensure that you also pass on all the
documentation.
Proper use
The belt sander is designed for dry sanding of large
surfaces of wood, plastic, metal, plaster and painted
surfaces. The device may only be used for dry sand-
ing. Always use a sanding belt and grade of grit
suitable for the particular surface you are sanding.
The speed selected should also be appropriate for
the material. The device is not intended for com-
mercial use. Any other use or modification to the
device shall be considered as improper use and
could give rise to considerable dangers. The manu-
facturer will not accept liability for loss or damage
arising from improper use.
Features and equipment
1
Belt speed adjuster wheel
2
Recesses for clamp mounting
3
ON / OFF switch
4
Lock button for ON / OFF switch
5
Dust box
6
Release button for dust box
7
Belt adjuster screw
8
Sanding belt
9
Adapter port
10
Tensioning lever for sanding belt
11
Clamps
12
Adapter for external vacuum extraction
13
Reducer piece
Included items
1 Belt sander PBS 600 A1
1 Sanding belt
1 Dust collection box
The following pictograms are used in these operating instructions / on the device:
Read instruction manual! Safety class II
Observe caution and safety notes!
Wear hearing protection, dust
protection mask, protective glasses
and protective gloves.
Caution – electric shock!
Danger to life!
Keep children away from electrical
power tools!
Explosive material! For indoor use only!
n
0
Rated idle running speed
Risk of loss of life by electric shock
from damaged mains lead or mains
plug!
V
~
Voltage
Dispose packaging and appliance in
an environmentally-friendly way!
W
Watts (Effective power)
7 GB
Introduction / General safety advice for electrical power tools
1 Vacuum extraction adapter and reducer piece
(for external vacuum extraction)
2 Clamps
1 Operating instructions
Technical information
Belt sander: Parkside PBS 600 A1
Nominal voltage: 230 V
~
50 Hz
Nom. power input: 600 W
No-load belt speed: 170 - 250 m / min
Sanding belt: 75 x 457 mm
Protection class: II /
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 89 dB(A)
Sound power level: 100 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Total vibration, EN 60745:
Vibration emission value a
h,D
= 2,5 m / s
2
Uncertainty K = 1.5 m / s
2
WARNING!
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different vi-
bration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical power
tool is used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of working, you should also take into
account the intervening periods of time when the
device is switched off or is running but is not actual-
ly in use. This can result in a much lower vibration
load over the whole of the period of working.
General safety advice for
electrical power tools
WARNING!
Read all the safety advice
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUC-
TIONS IN A SAFE PLACE FOR FUTURE REFER-
ENCE! THE TERM “ELECTRICAL TOOL” USED
IN THE SAFETY ADVICE REFERS TO ELECTRICAL
TOOLS POWERED BY MAINS ELECTRICITY (BY
MEANS OF A MAINS LEAD) AND ELECTRICAL
TOOLS POWERED BY RECHARGEABLE BATTER-
IES (WITHOUT A MAINS LEAD).
1.
Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other peo-
ple away while you are op-
erating the electrical tool.
Distractions can cause you to lose control of
the device.
2.
Electrical safety
To avoid danger to life from
electric shock:
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth. Unmodified
plugs and matching sockets reduce the risk of
electric shock.
8 GB
General safety advice for electrical power tools
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
device, to hang up the device or to pull
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
e) When working outdoors with an
electrical power tool always use ex-
tension cables that are also approved
for use outdoors. The use of an extension
cable suitable for outdoor use reduces the risk
of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electri-
cal power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo-
ment of carelessness when using the device
can lead to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected and
correctly used. The use of these devices re-
duces the hazard presented by dust.
4.
Careful handling and use of
electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug from the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
9 GB
General safety advice for electrical power tools
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are danger-
o
us when they are used by inexperienced peopl
e.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this,
take into account the working condi-
tions and the task in hand. The use of
electrical power tools for purposes other than
those intended can lead to dangerous situations.
Safety advice for
belt sanders
Hold the device by the insulated han-
dle surfaces as the sanding belt could
strike the device’s own mains lead.
Damaging a live wire could result in the metal
parts of the device also becoming live and
could lead to an electric shock.
DANGER OF FIRE FROM FLYING SPARKS!
Sanding metal creates flying sparks. For this
reason, always make sure that nobody is placed
in any danger and that there are no inflammable
materials near the working area.
When undertaking prolonged sanding of wood,
and in particular when working on materials
that give rise to dusts that are hazardous to
health, the sander must be connected to a
suitable external dust extraction device.
Ensure that there is adequate ventilation when
working on plastic, paint, varnish etc.
The belt sander is designed for the dry sanding
of large surfaces of wood, plastic, metal and
plaster and painted surfaces. The device is to
be used for dry sanding only.
Do not sand materials containing asbestos.
Asbestos is a known carcinogen.
WARNING!
POISONOUS DUSTS!
Sanding paints containing lead, some types of
wood and metal for example may give rise to
hazardous or poisonous dusts and represents a
risk to the health of the person operating the
device and to anyone near the work area.
Wear safety glasses and a dust
protection mask!
Securely support the workpiece. Use clamps or
a vice to grip the workpiece firmly. This is much
safer than holding it with your hand.
Never support yourself by placing your hands
near or in front of the device or the workpiece
surface. A slip can result in injury.
If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
Always work with the mains lead leading
away from the rear of the device.
Avoid contact with the moving sanding belt.
Do not work on moistened materials or damp
surfaces.
Always switch on the device before placing it
against the workpiece. After sanding, lift the de-
vice from the workpiece before switching it off.
When working always hold the device securely
with both hands (see Fig. E). Always keep prop-
er footing and balance.
Switch the device off and allow it to come to
a complete standstill before you put it down.
When taking a break from your work, before
carrying out any tasks on the device itself (e.g.
changing the sanding belt) and when you are
not using the device, always pull the mains
plug out of the mains socket.
10 GB
Preparing for use
Preparing for use
Tensioning / changing the
sanding belt
WARNING!
DANGER OF INJURY!
Before you carry out any work on the belt sander
always pull the plug out of the mains socket.
1. Then release the tensioner for the sanding belt
by moving the tensioning lever
10
fully outwards
(see fig. C). The sanding belt
8
can be removed.
2. Next insert a new sanding belt
8
or change
the belt for one suitable for a different material
or one with a different grit size.
IMPORTANT: The direction of the arrows on
the inside of the sanding belt
8
must agree
with that on sander housing.
3. Press the tensioning lever
10
back into its
initial position.
Adjusting the sanding belt path manually:
If the belt does not run centrally when switched on,
you may have to adjust the sanding belt manually.
To do this, turn the adjuster screw
7
on the front
roller until the sanding belt
8
runs centrally.
IMPORTANT: Always make sure that the
sanding belt
8
does not cut into the housing.
Check the sanding belt regularly and if neces-
sary re-adjust it using the adjuster screw
7
.
Advice on use
Light sanding pressure is enough:
Apply light sanding pressure only. The weight
of the belt sander alone is adequate to produce
good sanding results. By adopting this approach
you will also prolong the life of your sanding
belts and obtain a smoother workpiece surface.
Sanding and surfaces:
The sanding output and the quality of the surface
finish obtained are determined by the belt speed
and the grade of grit on the sanding belt (see the
section on “Selecting the correct rotational speed
and sanding belt”).
Sanding procedure:
With the sander switched on, bring it into con-
tact with the workpiece and move it forward
carefully. Work in parallel and overlapping
widths. Always work in the direction of the grain
to avoid undesirable transverse sanding marks.
After sanding always lift the device from the
workpiece before switching it off.
Vacuum dust extraction
WARNING!
DANGER OF FIRE! There is
the danger of fire when working with electrical de-
vices that have a dustbox or can be connected to a
vacuum cleaner. Under certain conditions the wood
dust in the dust collection box (or in the vacuum‘s
dust bag) may self-ignite, e.g. as a result of flying
sparks generated when abrading metals or metal
objects left in wood. This can happen particularly if
the wood dust is mixed with paint residue or other
chemicals and the abraded particles are hot from
prolonged abrasion. Therefore you must empty the
device’s dust collection box and the vacuum clean-
er’s dust bag before taking a break or stopping
work and always avoid overheating of the abraded
particles and the device.
Wear a dust mask!
Dust extraction with dust box:
Push the dust box
5
on to the adapter port
9
.
Dismantle / remove the dust box:
Press the release button
6
of the dust box
5
and withdraw it towards the rear of the device.
Adapter for external vacuum extraction
(with reducer piece)
WARNING!
EXPLOSIVE MATERIAL!
If there is an explosive mixture of dust and air you
must use a vacuum device especially intended for
that purpose.
DANGER OF FIRE FROM FLYING SPARKS!
Do not use any form of dust extraction (dust box
5
or vacuum extraction device) if you are sanding metal.
11 GB
Preparing for use / Operation
Connection:
Push the adapter for external vacuum extraction
12
into the adapter port
9
. If it is necessary to
use the reducer piece
13
, push the reducer piece
into the adapter for external vacuum extraction
12
.
Slide the hose of a suitable dust extraction de-
vice approved for that purpose (e.g. a workshop
vacuum cleaner) on to the adapter for external
vacuum extraction
12
with the reducer piece
13
,
if used.
Removal:
Pull off the dust extraction device hose.
Pull off the adapter for external vacuum extrac-
tion
12
(with the reducer piece
13
, if used).
Operation
Switching on and off
When operating the belt sander you can select
between intermittent or continuous operation mode.
To switch on intermittent operation mode:
Press the ON / OFF switch
3
.
To switch off intermittent operation mode:
Release the ON / OFF switch
3
.
To switch on continuous operation mode:
Press the ON / OFF switch
3
, and keep it
pressed, then press the locking knob
4
.
To switch off continuous operation mode:
Press and then release the ON / OFF switch
3
.
Selecting the correct rotational
speed and sanding belt
You can select the belt speed using the belt speed
adjuster wheel
1
even whilst the sander is running.
The optimum belt speed depends on the workpiece
and the workpiece material. Always confirm the best
speed by carrying out a small test. The following
table lists some recommended values to help you
determine the optimum speed.
Material / type of
work
Softwood
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 240
Preselected rotation
speed
high (5-6)
Material / type of
work
Hardwood
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 180
Preselected rotation
speed
high (5-6)
Material / type of
work
Chipboard
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 150
Preselected rotation
speed
high (5-6)
Material / type of
work
Removing paint /
varnish
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) ––
Preselected rotation
speed
high (5-6)
Material / type of
work
Sanding varnish
Coarse finish
(Grit grade)
150
Fine finish (Grit grade) 320
Preselected rotation
speed
low (1-2)
12 GB
Material / type of
work
Rust removal
Coarse finish
(Grit grade)
40
Fine finish (Grit grade) 120
Preselected rotation
speed
medium / high (3-4)
Material / type of
work
Plastic
Coarse finish
(Grit grade)
120
Fine finish (Grit grade) 240
Preselected rotation
speed
low / medium (2-3)
Material / type of
work
Non-ferrous metals
(e.g. aluminium)
Coarse finish
(Grit grade)
80
Fine finish (Grit grade) 150
Preselected rotation
speed
medium / high (3-4)
Using the device in
a fixed mounting
Turn the electrical power tool upside down as
shown in Figures D, F and place it on a stable
working surface.
Insert the two clamps
11
into the recesses
2
provided for this purpose and clamp the electri-
cal power tool securely down on to the surface.
Tips and tricks
Never use the same sanding belt to sand wood
and metal.
Worn or ripped sanding belts can damage
the workpiece. Change sanding belts at the
appropriate time.
Keep the sanding belt properly tensioned so
that it does not hang down too much and
become unusable due to nicks, creases etc.
Maintenance and cleaning
WARNING!
Before you carry out any work
on the belt sander always pull the mains plug out
of the mains socket.
The belt sander is designed to be maintenance-free.
Clean the device frequently. This should be done
immediately after you have finished using it.
Use a dry cloth to clean the device - never use
petrol, solvents or cleaners that attack plastic.
Emptying / cleaning the dust box:
Simultaneously press the two release button(s)
6
and pull the dust box
5
backwards from of
the device.
Empty the dust collection box completely by
knocking the dust out and place the dust box
back on to the device.
Always keep the ventilation slots clear.
Remove any adhering dust with a narrow
paint brush.
Service centre
WARNING!
Have your device re-
paired only by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
WARNING!
If the plug or mains lead
needs to be replaced, always have the
replacement carried out by the manu-
facturer or its service centre. This will
ensure that your device remains safe to use.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
Operation / Maintenance and cleaning / Service centre / Warranty
13 GB
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage, f
or
wearing parts or for damage to fragile components,
e.g. buttons or batteries. This product is for private
use only and is not intended for commercial use.
The warranty is void in the case of abusive and im-
proper handling, use of force and internal tamper-
ing not carried out by our authorized service branch.
Your statutory rights are not restricted in any way
by this warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
DES UK LTD
Tel.: 0871 5000 700 (£ 0.10 / minute)
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electrical power
tools with the household rubbish!
In accordance with European Directive 2002 / 96 / EC
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn
out electrical power tools must be collected sepa
rately
and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for
more details of how to dispose of your worn out
electrical devices.
Declaration of Conformity /
Manufacturer
We, Kompernaß GmbH, the person responsible for
documents: Mr Dennis Dohm, Burgstr. 21,
D-44867 Bochum, Germany, hereby declare that
this product complies with the following standards,
normative documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60745-1:2006
EN 60745-2-4:2003+A11
EN 55014-1:2006
EN 55014-2:1997+A1
EN 61000-3-2:2006
EN 61000-3-3:1995+A1+A2
Type / Description of product:
Belt sander PBS 600 A1
Date of manufacture (DOM): 04 - 2010
Serial number: IAN 49405
Bochum, 30.04.2010
Hans Kompernaß
- Managing Director -
We reserve the right to make technical modifications
in the course of further development.
Warranty / Disposal / Declaration of Conformity / Manufacturer
14
15 PL
Spis zawartości
Wstęp
ytkowanie zgodnie z przezna cze niem .................................................................St rona 16
Wyp o s ażenie ...............................................................................................................St rona 16
Zakres dostawy ...........................................................................................................Strona 17
Dane techniczne ..........................................................................................................Strona 17
Ogólne wskazówki bezpieczeństwa dla
elektronarzędzi
1. Bezpieczeństwo miejsca pracy ..............................................................................Strona 17
2.
Bezpieczeństwo elektryczne ..................................................................................Strona 18
3. Bezpieczeństwo osób .............................................................................................Strona 18
4.
Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ....................Strona 19
Wskazówki dotycce bezpieczeństwa dla szlifierki taśmowej ............................Strona 19
Uruchomienie
Zamocowanie / wymiana taśmy szlifierskiej .............................................................Strona 20
Wskazówki robocze....................................................................................................Strona 20
Odsysanie pyłu ............................................................................................................Strona 21
Obsługa
Włączanie i wyłączanie .............................................................................................Strona 21
Wybór obrotów i taśmy szlifierskiej ...........................................................................Strona 22
Praca stacjonarna ........................................................................................................Strona 23
Dobre rady i triki ..........................................................................................................Strona 23
Konserwacja i czyszczenie ....................................................................... Strona 23
Serwis .........................................................................................................................Strona 23
Gwarancja .............................................................................................................. Strona 23
Utylizacja ................................................................................................................. Strona 24
Deklaracja zgodności / Producent .....................................................Strona 24
16 PL
Wstęp
Szlifierka taśmowa PBS 600 A1
Wstęp
Przed pierwszym uruchomieniem należy
zapoznać się z działaniem urządzenia i
nauczyć się właściwego obchodzenia
się z elektronarzędziami. W tym celu należy prze-
czytać poniższą instrukcję. Instrukcję należy staran-
nie przechowywać. W razie przekazania urządzenia
osobom trzecim należy dać również niniejszą in-
strukcję obsługi.
Użytkowanie zgodnie
z przeznaczeniem
Szlifierka taśmowa jest zaprojektowana do szlifo-
wania na sucho powierzchni drewna, tworzywa
sztucznego, metalu i masy szpachlowej oraz
powierzchni lakierowanych. Urządzenia wolno
używać wyłącznie do szlifowania na sucho. Zwróć
uwagę na to, żeby do obróbki różnych materiałów
stosować odpowiednie arkusze szlifierskie o zróż-
nicowanej ziarnistości, a także na to, żeby również
dopasować obroty do materiału. Urządzenie nie
jest przewidziane do celów zarobkowych. Każde
inne zastosowanie maszyny lub przeprowadzenie
w niej zmian jest uznawane za niezgodne z prze-
znaczeniem i kryje w sobie poważne zagrożenie
nieszczęśliwym wypadkiem. Za szkody powstałe
wskutek sprzecznego z przeznaczeniem użytkowa-
nia producent nie ponosi żadnej odpowiedzialności.
Wyposażenie
1
Kółko nastawcze prędkości taśmy
2
Wycięcia na śrubowy ścisk stolarski
3
WŁĄCZNIK / WYŁĄCZNIK
4
Przycisk blokady WŁĄCZNIKA / WYŁĄCZNIKA
5
Pojemnik na pył
6
Przycisk zwalniający pojemnika na p
7
Śruba regulacyjna biegu taśmy
8
Taśma szlifierska
9
Przyłącze adaptera
10
Dźwignia napinająca taśmy szlifierskiej
11
Śrubowy ścisk stolarski
12
Adapter do odpylania zewnętrznego
13
Złączka redukcyjna
W niniejszej instrukcji obsługi urządzenia zastosowano następujące piktogramy:
Przeczytaj instrukcję obsługi! Klasa bezpieczeństwa II
Przestrzegaj wskazówek
ostrzegawczych i bezpieczeństwa!
Zakładać okulary ochronne, ochronniki
słuchu, maskę przeciwpyłową i rękawice
ochronne.
Ostrzeżenie przed porażeniem prądem
elektrycznym! Zagrożenie dla życia!
Dzieci trzymać z daleka od narzędzia
elektrycznego!
Niebezpieczeństwo wybuchu!
Tylko do użytku w pomieszczeniach
wewnętrznych!
n
0
Projektowe obroty biegu jałowego
Niebezpieczeństwo utraty życia wsku-
tek porażenia prądem elektrycznym
w przypadku uszkodzonego kabla
sieciowego lub uszkodzonej wtyczki
sieciowej!
V
~
Volt (Napięcie przemienne)
Opakowanie i urządzenie przekaż
do utylizacji zgodnie z przepisami
o ochronie środowiska!
W
Watt (Moc skuteczna)
17 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Zakres dostawy
1 Szlifierka taśmowa PBS 600 A1
1 Taśma szlifierska
1 Pojemnik zintegrowanego systemu odsysania pyłu
1 Adapter odpylania i złączka redukcyjna
(do odpylania zewnętrznego)
2 Śrubowe ściski stolarskie
1 Instrukcja obsługi
Dane techniczne
Szlifierka taśmowa:
Parkside PBS 600 A1
Napięcie znamionowe: 230 V
~
50 Hz
Pobór mocy znamionowy: 600 W
Bieg jałowy-Prędkość taśmy: 170 - 250 m / min
Taśma szlifierska: 75 x 457 mm
Klasa ochrony: II /
Informacje dotyczące hałasu i wibracji:
Wartość pomiarowa hałasu wyznaczona zgodnie
z EN 60745. Poziom hałasu elektronarzędzia wg
oceny A wynosi typowo:
Poziom ciśnienia hałasu: 89 dB(A)
Pozom mocy hałasu: 100 dB(A)
Niepewność pomiaru K: 3 dB
Zakładać ochronniki słuchu!
Wartości całkowite drgań, EN 60745:
Wartość emisji drgań a
h,D
= 2,5 m / s
2
Niepewność K = 1,5 m / s
2
OSTRZEŻENIE!
Podany w niniejszych in-
strukcjach poziom drgań wyznaczony został za
pomocą metody pomiarowej określonej w normie
EN 60745 i może zostać użyty do porównania
urządzeń. Poziom wibracji będzie się różnił w za-
leżności od zastosowania elektronarzędzia i w nie-
których przypadkach może przekroczyć wartość
podaną w niniejszej instrukcji. Obciążenie drgania-
mi może być mniej uciążliwe, jeśli elektronarzędzie
będzie regularnie trzymane w ten sposób.
Wskazówka: Celem dokładnego oszacowania
obciążenia wibracjami w okresie określonego okre-
su czasu pracy należy uwzględnić również te okresy,
w których urządzenie jest wyłączone lub wprawdzie
jest włączone, ale w rzeczywistości nie pracuje.
Może to przyczynić się do znacznej redukcji obciąże-
nia wibracjami w całym okresie czasu pracy.
Ogólne wskazówki
bezpieczeństwa dla
elektronarzędzi
OSTRZEŻENIE!
Przeczytaj wszystkie
wskazówki dotyczące bezpieczeństwa
oraz instrukcje! Zaniedbania w przestrzeganiu
wskazówek dotyczących bezpieczeństwa oraz w
przestrzeganiu instrukcji mogą spowodować pora-
żenie prądem elektrycznym, pożar i / lub ciężkie
obrażenia ciała.
PRZECHOWUJ NA PRZYSZŁOŚĆ WSZYSTKIE
WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA
ORAZ INSTRUKCJE! UŻYWANY WE WSKA-
ZÓWKACH DOTYCZĄCYCH BEZPIECZEŃSTWA
TERMIN „NARZĘDZIE ELEKTRYCZNE“ ODNOSI
SIĘ DO NARZĘDZI ELEKTRYCZNYCH ZASILA-
NYCH Z SIECI (Z KABLEM SIECIOWYM) ORAZ
DO NARZĘDZI ELEKTRYCZNYCH ZASILANYCH
Z AKUMULATORÓW (BEZ KABLA SIECIOWEGO).
1.
Bezpieczeństwo miejsca pracy
a) Utrzymywać stanowisko pracy w czy-
stości i dobrze oświetlone. Nieporządek
i nieoświetlone obszary robocze mogą prowa-
dzić do wypadków.
b)
Nie pracuj przy użyciu urzą-
dzenia w otoczeniu zagrożo-
nym eksplozją, w którym
znajdują się palne ciecze, gazy lub
pyły. Urządzenia elektryczne wytwarzają
iskry, które mogą zapalić pył lub pary.
c)
Podczas użytkowania urzą-
dzenia elektrycznego trzymaj
dzieci i inne osoby z daleka
od urządzenia. Przy odchyleniu możesz
stracić kontrolę nad urządzeniem.
18 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
2.
Bezpieczeństwo elektryczne
Unikaj niebezpieczeństwa
utraty życia wskutek porażenia
prądem elektrycznym:
a) Wtyk sieciowy urządzenia musi
pasować do wtykowego gniazdka
sieciowego. W żaden sposób nie wol-
no zmieniać wtyku sieciowego urzą-
dzenia. Nie używaj żadnych wtyków
adapterowych razem z urządzeniami
wyposażonymi w uziemienie ochron-
ne. Niezmienione wtyki sieciowe i pasujące
wtykowe gniazdka sieciowe zmniejszają
ryzyko porażenia prądem elektrycznym.
b) Unikaj kontaktu fizycznego z powier-
zchniami uziemionymi takimi jak
powierzchnie rur, grzejników, kuchni
elektrycznych i lodówek. Istnieje podwyż-
szone niebezpieczeństwo porażenia prądem
elektrycznym, gdy twoje ciało jest uziemione.
c) Trzymaj urządzenie z daleka od desz-
czu i wilgoci. Wniknięcie wody do urządze-
nia elektrycznego zwiększa ryzyko porażenia
prądem elektrycznym.
d)
Nie używaj kabla sieciowego w
sposób sprzeczny z jego prze-
znaczeniem, tj. do noszenia
urządzenia, zawieszania urzą dzenie
lub do wyciągania wtyku sieciowego
z wtykowego gniazdka sieciowego.
Trzymaj kabel z daleka od gorąca,
oleju, ostrych krawędzi lub porusza-
jących się części urządzeń. Uszkodzone
lub poplątane kable zwiększają ryzyko pora-
żenia prądem elektrycznym.
e)
Gdy pracujesz z urządzeniem elektrycz-
nym na dworze używaj wyłącznie
przedłużaczy, które są dopuszczone
również do pracy na dworze. Użycie
przedłużacza przystosowanego do stosowania
na dworze zmniejsza ryzyko porażenia prądem
elektrycznym.
f) Jeśli praca elektronarzędzia w otocze-
niu wilgotnym jest nie do uniknięcia,
należy zastosować wyłącznik prądu
uszkodzeniowego. Zastosowanie wyłącz-
nika prądu uszkodzeniowego zapobiega nie-
bezpieczeństwu porażenia prądem elektrycznym.
3. Bezpieczeństwo osób
a) Bądź stale uważny, zwracaj uwagę
na to co robisz i postępuj rozsądnie w
trakcie pracy z narzędziem elektrycz-
nym. Nie używaj narzędzia, gdy jesteś
zmęczony lub znajdujesz się pod
wpływem narkotyków, alkoholu lub
lekarstw. Chwila nieuwagi przy użytkowaniu
urządzenia może prowadzić do poważnych
obrażeń ciała.
b)
Noś osobiste wyposażenie
ochronne i zawsze okulary
ochronne. Noszenie osobistego
wyposażenia ochronnego takiego jak maska
przeciwpyłowa, buty antypoślizgowe, kask
ochronny lub ochrona słuchu stosownie do
sposobu użytkowania narzędzia elektrycznego
zmniejsza ryzyko obrażeń ciała.
c) Unikaj niezamierzonego uruchomienia.
Upewnij się, że narzędzie elektryczne
jest wyłączone zanim podłączysz je
do zasilania prądowego, uchwycisz je
lub będziesz je przenosił. Jeżeli podczas
przenoszenia urządzenia będziesz trzymał pa-
lec na przełączniku WŁĄCZ. / WYŁĄCZ. lub
jeżeli urządzenie jest włączone, to może to
prowadzić do nieszczęśliwych wypadków.
d) Usuń narzędzia do nastawiania urzą-
dzenia lub klucze płaskie zanim włą-
czysz urządzenie. Narzędzie lub klucz,
który znajduje się w obracającej się części
urządzenia może prowadzić do obrażeń ciała.
e) Unikaj nienormalnej postawy ciała.
Zadbaj o pewne stanowisko i w każ-
dej chwili utrzymuj równowagę. Dzięki
temu będziesz mógł lepiej kontrolować urzą-
dzenie, zwłaszcza w nieoczekiwanych
sytuacjach.
f) Noś odpowiednią odzież. Nie noś ob-
szernej odzieży ani biżuterii. Trzymaj
włosy, odzież i rękawice z daleka od
poruszających się części. Luźna odzież,
19 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
biżuteria lub długie włosy mogą zostać uchwy-
cone przez poruszające się części.
g) Jeżeli zostaną zamontowane urzą-
dzenia do odsysania i wychwytywania
pyłu, to upewnij się, że są one podłą-
czone i że będą prawidłowo używane.
Używanie tych urządzeń zmniejsza zagrożenie
wywoływane pyłem.
4.
Staranne obchodzenie
się i użytkowanie narzędzi
elektrycznych
a) Nie przeciążaj urządzenia. Używaj
do swojej pracy przeznaczonego do
niej narzędzia elektrycznego. Za pomo-
cą odpowiedniego narzędzia elektrycznego
pracujesz lepiej i bezpieczniej w danym zakre-
sie robót.
b) Nie używaj żadnego narzędzia elek-
trycznego, którego przełącznik jest
uszkodzony. Narzędzie elektryczne, które
nie daje się już więcej włączyć lub wyłączyć,
jest niebezpieczne i musi zostać naprawione.
c) Zanim przeprowadzisz nastawy urzą-
dzenia, wymienisz części osprzętu lub
odłożysz urządzenie wyciągnij wtycz-
kę sieciową z sieciowego gniazdka
wtykowego. Ten środek ostrożności zapo-
biega niezamierzonemu startowi urządzenia.
d) Przechowuj nieużywane narzędzia
elektryczne poza zasięgiem dzieci. Nie
pozwól na użytkowanie urządzenia
osobom, które nie są z nim obznajo-
mione lub nie przeczytały niniejszych
instrukcji. Narzędzia elektryczne są niebez-
pieczne, gdy są używane przez osoby niedo-
świadczone.
e) Pielęgnuj starannie urządzenie.
Sprawdź, czy ruchome części urzą-
dzenia funkcjonują nienagannie i nie
zakleszczają się, czy części urządzenia
nie są złamane lub uszkodzone w ta-
kim stopniu, że funkcjonowanie urzą-
dzenia jest uszczuplone. Zleć napra
uszkodzonych części przed użyciem
urządzenia. Przyczyną wielu wypadków są
źle konserwowane narzędzia elektryczne.
f) Utrzymuj narzędzia tnące w stanie
ostrym i czystym. Starannie pielęgnowane
narzędzia tnące o ostrych krawędziach tną-
cych mniej zakleszczają się i dają się łatwiej
prowadzić.
g) Używaj narzędzia elektrycznego,
osprzętu, narzędzi wymiennych itp.
odpowiednio do niniejszych instrukcji
i w taki sposób, jaki jest zalecany dla
tego specjalnego typu urządzenia.
Uwzględniaj przy tym warunki robo-
cze i wykonywane czynności. Użycie
narzędzi elektrycznych do innych zastosow
niż to przewidziano może prowadzić do nie-
bezpiecznych sytuacji.
Wskazówki dotyczące
bezpieczeństwa dla
szlifierki taśmowej
Niniejsze urządzenie należy trzymać
na
izolowanych powierzchniach uchwytόw
,
jako że taśma szlifierska może uszko-
dzić własny przewόd sieciowy. Uszko-
dzenie przewodόw przewodzących prąd elek-
tryczny może spowodować, że metalowe części
urządzenia znajdą się pod napięciem oraz do-
prowadzić do porażenia prądem elektrycznym.
ZAGROŻENIE POŻAROWE WSKUTEK
WYRZUCANIA ISKIER! Gdy szlifowane są
metale postaje wyrzut iskier. Dlatego też należy
bezwzględnie zwracać uwagę na to, żeby nie
zostały zagrożone żadne osoby oraz żeby w
pobliżu obszaru roboczego nie znajdowały się
żadne palne materiały.
Przy obróbce drewna, a zwłaszcza, gdy obra-
biane będą materiały, w przypadku których
powstają szkodliwe dla zdrowia pyły, należy
podłączyć odpowiednie zewnętrzne urządzenie
odsysające.
Przy obróbce tworzyw sztucznych, farb,
lakierów itp. należy zadbać o wystarczające
napowietrzanie.
Szlifierka taśmowa jest zaprojektowana do szli-
fowania powierzchniowego na sucho drewna,
tworzywa sztucznego, metalu i masy szpachlowej
20 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi / Uruchomienie
oraz powierzchni lakierowanych. Urządzenie
wolno stosować tylko do szlifu suchego.
Materiału zawierającego azbest nie wolno ob-
rabiać. Azbest jest uznawany za rakotwórczy.
OSTRZEŻENIE!
TRUJACE PYŁY! Powsta-
jące przy szlifowaniu na przykład powłok ma-
larskich zawierających ołów, niektórych rodzajów
drewna oraz metali szkodliwe / trujące pyły
stanowią zagrożenie zdrowia dla osoby obsłu-
gującej urządzenie lub dla osób znajdujących
się w pobliżu.
Noś okulary ochronne i maskę
przeciwpyłową!
Zabezpieczaj przedmiot obrabiany. Używaj
urządzenia mocującego / imadła, aby przy-
trzymać przedmiot obrabiany. W ten sposób
jest on przytrzymywany pewniej niż ręką.
W żadnym wypadku nie opieraj rąk obok lub
przed urządzeniem oraz przed obrabianą
powierzchnią, ponieważ w razie ześlizgnięcia
istnieje niebezpieczeństwo obrażeń ciała.
W przypadku niebezpieczeństwa wyciągnij
natychmiast wtyczkę sieciową z wtykowego
gniazdka sieciowego.
Zawsze prowadź kabel od urządzenia do tyłu.
Unikaj kontaktu z biegnącą taśmą szlifierską.
Nie obrabiaj żadnych zwilżonych lub wilgot-
nych powierzchni.
Urządzenie należy prowadzić zawsze w stanie
włączonym do przedmiotu obrabianego. Po
obróbce należy podnieść urządzenie z przed-
miotu obrabianego i dopiero wtedy je wyłączyć.
W trakcie obróbki zawsze trzymaj urządzenie
mocno oburącz (zobacz również rysunek E).
Zadbaj o pewną podstawę.
Pozwól, aby urządzenie całkowicie zatrzymało
się i wyłącz je zanim je odłożysz.
Podczas przerw w pracy, przed wszelkimi ro-
botami na urządzeniu (na przykład wymiana
papieru ściernego)oraz w przypadku nieużyt-
kowania urządzenia należy zawsze wyciągnąć
wtyk sieciowy z wtykowego gniazdka sieciowego
.
Uruchomienie
Zamocowanie / wymiana
taśmy szlifierskiej
OSTRZEŻENIE!
NIEBEZPIECZEŃSTWO
POWSTANIA OBRAŻEŃ! Zawsze wyciągnij wtyk
sieciowy z wtykowego gniazdka sieciowego zanim
przystąpisz do wykonania robót na szlifierce taśmowej.
1. Poluzuj najpierw urządzenie mocujące taśmy
szlifierskiej odchylając całkowicie dźwignię
mocującą
10
(zobacz Rysunek C). Taśmę szli-
fierską
8
można zdjąć.
2. Teraz należy założyć nową taśmę szlifierską
8
względnie wymienić ją, aby obrabiać inny
materiał lub zmienić ziarnistość.
WAŻNE: Kierunki strzałek na stronie wewnętrz-
nej taśmy szlifierskiej
8
oraz na obudowie
urządzenia muszą być zgodne.
3. Naciśnij znowu dźwignię mocująca
10
w pozycję wyjściową.
Ręczna regulacja taśmy szlifierskiej:
Jeśli po włączeniu taśma nie biegnie centrycznie,
należy dokonać ręcznej regulacji.
W tym celu należy pokręcać śrubę regulacyjną
7
na przedniej rolce, dopóki taśma szlifierska
nie będzie biec centrycznie
8
.
WAŻNE: Zwracaj bezwzględnie uwagę na
to, żeby taśma szlifierska
8
nie ocierała się o
obudowę. Sprawdzaj regularnie bieg taśmy i
w razie potrzeby wyreguluj go za pomocą
śruby justującej
7
.
Wskazówki robocze
Niewielki nacisk przy szlifowaniu
wystarczy:
Pracuj przy niewielkim nacisku szlifowania. Ciężar
własny szlifierki taśmowej jest wystarczający
do uzyskania dobrych wydajności szlifowania.
Dzięki takiemu sposobowi pracy oszczędzasz
zużycie taśmy szlifierskiej, a powierzchnia ob-
rabianego przedmiotu będzie gładsza.
21 PL
Uruchomienie / Obsługa
Usuwanie materiału i powierzchnia:
Wydajność usuwania materiału i jakość powierzch-
ni jest wyznaczana przez prędkość taśmy szlifierskiej
oraz grubość ziarna taśmy szlifierskiej (zobacz rów-
nież rozdział »Wybór obrotów i taśmy szlifierskiej«).
Proces szlifowania:
Włączone urządzenie ulokować na obrabianym
przedmiocie i pracować z równomiernym
posuwem. Proces szlifowania należy prowadzić
wnoległymi pasmami i na zakładkę. Aby
uniknąć zakłócających obraz szlifu, przebiega-
jących poprzecznie śladów szlifowania, należy
szlifować wyłącznie w kierunku włókien. Po
obróbce podnieś urządzenie z przedmiotu
obrabianego i dopiero wtedy je wyłącz.
Odsysanie pyłu
OSTRZEŻENIE!
ZAGROŻENIE POŻA-
ROWE! W trakcie robót z urządzeniami elektrycz-
nymi, które dysponują pojemnikami zintegrowanego
systemu odsysania pyłu lub które mogą zostać
połączone poprzez urządzenie odsysające pył z
odkurzaczem, istnieje zagrożenie pożarowe! Przy
niekorzystnych warunkach, takich jak na przykład
wyrzucanie iskier przy szlifowaniu metalu lub resztek
metalu w drewnie może nastąpić samozapłon pyłu
drzewnego w pojemniku zintegrowanego systemu
odsysania pyłu (lub w worku na pył odkurzacza).
Może to nastąpić w szczególności wtedy, gdy pył
drzewny jest wymieszany z resztkami lakieru lub
innymi substancjami chemicznymi, a zeszlifowany
materiał wskutek dłuższej pracy szlifierki jest gorący.
Dlatego też należy bezwzględnie unikać przegrza-
nia zeszlifowanego materiału oraz urządzenia i
przed przerwami w pracy zawsze opróżniać po-
jemnik zintegrowanego systemu odsysania pyłu
względnie worek odkurzacza.
Noś maskę przeciwpyłową!
Odpylanie za pomocą pojemnika na pył:
Nasunąć pojemnik na p
5
na przyłącze
adaptera
9
.
Demontaż pojemnika pyłu:
Nacisnąć przyciski zwalniające
6
pojemnik
na pył
5
i pociągnąć go do tyłu.
Adapter do odpylania zewnętrznego
(ze złączką redukcyjną)
OSTRZEŻENIE!
NIEBEZPIECZEŃSTWO
WYBUCHU! W przypadku wybuchowej miesza-
niny pył / powietrze musisz użyć nadającego się
specjalnie do tego celu odsysacza.
NIEBEZPIECZEŃSTWO POWSTANIA PO-
ŻARU OD WYLATUJĄCYCH ISKIER! Podczas
szlifowania powierzchni metalowych nie należy
używać odpylania (pojemnik na pył
5
lub odku-
rzacz).
Podłączenie:
Wsunąć adapter odpylania zewnętrznego
12
do przyłącza adaptera
9
. W razie potrzeby
użyć złączki redukcyjnej
13
, wsuwając ją do
adaptera odpylania zewnętrznego
12
.
Nasunąć wąż dopuszczonego urządzenia od-
pylającego (np. odkurzacza przemysłowego)
na adapter odpylania zewnętrznego
12
w
razie potrzeby ze złączką redukcyjną
13
.
Zdejmowanie:
Zdjąć wąż urządzenia odpylającego.
Zdjąć adapter odpylania zewnętrznego
12
ewentualnie ze złączką redukcyjną
13
.
Obsługa
Włączanie i wyłączanie
W trakcie eksploatacji szlifierki taśmowej możesz
wybrać między trybem pracy chwilowym a trybem
pracy długotrwałym.
Włączenie trybu pracy chwilowej:
Naciśnij przełącznik WŁĄCZ. / WYŁĄCZ.
3
.
Wyłączenie trybu pracy chwilowej:
Zwolnij przełącznik WŁĄCZ. / WYŁĄCZ.
3
.
1 / 1

Parkside PBS 600 A1 Operation and Safety Notes

Kategoria
Szlifierki elektryczne
Typ
Operation and Safety Notes
Ten podręcznik jest również odpowiedni dla

w innych językach