Yamaha DS2416 Instrukcja obsługi

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

M

DS2416

DIGITAL MIXING CARD

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: YAMAHA CORPORATION OF AMERICA

Address: 6600 Orangethorpe Avenue, Buena Park, Calif. 90620 U.S.A.

Telephone: 1-714-522-9011

FAX: 1-714-739-2680

Type of Equipment: DIGITAL MIXING CARD

Model Name: DS2416

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on

different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in

is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

1

DS2416—Owner’s Manual

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Yamaha DSP Factory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

System Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Compatible Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the DS2416 . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Testing the DS2416 . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the Test Program . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using the Test Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Wordclocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Recording Digitally to the DS2416 . . . . . . . . . . . . . . . . . . . 11

Recording Digitally to DAT . . . . . . . . . . . . . . . . . . . . . . . . . 11

Digitally Cascading DS2416 Cards . . . . . . . . . . . . . . . . 12

DS2416 Q&A (Questions & Answers) . . . . . . . . . . . . . . 13

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Effects Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Effects Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

2

DS2416—Owner’s Manual

Important Notices

• Do not place the DS2416 in an area subject to excessive heat, direct sun-

light, excessive humidity, or dust.

• Keep the DS2416 inside its antistatic bag until you are ready to install it.

• To prevent handling damage, hold the DS2416 by the edges or bracket.

• If you accidentally touch the card edge connections, remove any ﬁnger-

prints using a dry tissue.

• Do not place objects on top of the DS2416, and do not put it down in a

place where other objects are likely to be placed on top of it.

• Before removing your computer’s cover, turn it off and remove the power

cord.

• To prevent static electricity damage, touch a grounded metal part of your

computer, such as the power supply case, before handling the DS2416.

Packing List

• DS2416 Digital Mixing Card

• Driver and Test program ﬂoppy disk

• 14-pin to 16-pin cable

• This manual

Trademarks

IBM PC is a registered trademark of International Business Machines. Korg is

a trademark of Korg, Inc. Pentium is a registered trademark of Intel. Sound

Blaster is a registered trademark of Advanced WavEffects. Windows 95 is a

trademark of Microsoft. Yamaha is a trademark of Yamaha Corporation. All

other trademarks are the property of their respective holders and are hereby

acknowledged.

Copyright

No part of the DS2416

Owner’s Manual

may be reproduced or distributed in

any form or by any means without the prior written authorization of Yamaha

Corporation, Inc.

Keep this manual for future reference!

Introduction

3

DS2416—Owner’s Manual

Introduction

Thank you for purchasing the Yamaha DS2416 Digital Mixing Card. With

8-track simultaneous recording, 16-track simultaneous playback, 24-channel

mixing, 4-band parametric EQ, effects, and dynamics, the DS2416 provides a

complete digital recording studio inside a regular personal computer. Unlike

other audio cards, the DS2416’s ﬁve DSPs take the load off the computer’s

main processor leaving it free to concentrate on timing and other tasks while

the DS2416 takes care of high-quality effects, EQ, and dynamics processing.

In some cases, the DS2416’s onboard processing powerhouse may allow audio

software to record and playback a greater number of tracks.

For ease of installation and high data throughput, the DS2416 uses the indus-

try-standard PCI (Peripheral Component Interconnect) bus. Sound cards can

be connected digitally, or two DS2416 cards can be digitally cascaded for

48-channel mixing, each providing 2-channel analog inputs and outputs,

with 20-bit 128-times oversampling A/D converters and 20-bit 8-times over-

sampling D/A converters, and stereo coaxial digital input and output. Inputs

and outputs can be expanded using the optional AX44 Audio Expansion Unit,

which offers four 1/4-inch analog inputs—two of which can be used with

microphones—four 1/4-inch analog outputs and a stereo headphone jack.

Two AX44s can be used with each DS2416 card for eight analog inputs and

outputs.

Yamaha DSP Factory

The DS2416 Digital Mixing Card forms the heart of the Yamaha DSP Factory

system, a range of products designed to bring professional digital multitrack

recording and mixing to personal computers. Other DSP Factory products

include the AX44 Audio Expansion Unit, and several analog and digital

multi-channel input and output options are currently under development.

Check out the Yamaha Professional Audio Web site for the latest information

<http://www.yamaha.co.jp/product/proaudio/homeenglish/>.

Important Note

Whether you can actually use all the DS2416 functions that appear in the

manual will depend on your audio software.

4

Introduction

DS2416—Owner’s Manual

System Requirements

• IBM PC compatible PCI bus Windows 95 computer

• DS2416-compatible audio software

System Notes

The DS2416 can be used in any IBM PC-compatible PCI bus personal com-

puter running Windows 95. The DS2416 requires a single 5 V PCI expansion

bus slot, and cannot be used in 3.3 V PCI slots. It’s compliant with PCI ver-

sion 2.1, requires one IRQ (interrupt request), but no DMA (Direct Memory

Access). Since it’s a PCI card, IRQ settings are made automatically. PCI bus

speeds greater than 33 MHz are not supported.

Processor type, memory, and hard disk requirements are dependent on the

controlling software, not the DS2416. The supplied device driver requires a

few hundred kilobytes of disk space. Although the DS2416 supports 8-track

simultaneous recording and 16-track simultaneous playback, actual perfor-

mance will depend on the capabilities of your computer and audio software.

Compatible Software

Any software that supports Windows MME (Multimedia Extensions), includ-

ing the Windows 95 Media Player accessory, can be used with the DS2416 for

recording and playback. To use the mixing functions, however, requires soft-

ware that supports the DS2416 mixer. As of April 1998, the following software

companies are developing, or have already released software for the DS2416.

Please visit the following Web sites for more information.

•

C-Mexx

<http://www.c-mexx.com/>

•

Cakewalk

<http://www.cakewalk.com/>

•

Canam Computers

<http://www.canam-comp.fr/>

•

Emagic

<http://www.emagic.de/>

•

IQS (Innovative Quality Software)

<http://www.iqsoft.com/>

•

Musicator

<http://www.musicator.com/>

•

SEK’D

<http://www.sekd.com/CConsole/StudCcons.htm>

•

Sonic Foundry

<http://www.sfoundry.com/>

•

Steinberg

<http://www.steinberg.de/>

Audio software that doesn’t support all the features of the DS2416 can still use

a basic feature set. However, input and output patching is ﬁxed, as shown in

the “Fixed Patchbay Diagram” on page 25. The Windows 95 Volume Control

can be used to set the stereo master fader and mute, and the level meters dis-

play the recording levels.

Features

5

DS2416—Owner’s Manual

Features

General

• PCI bus card (compliant with version 2.1)

• Support for Windows 95 MME (Multimedia Extensions)

• Plug and Play installation

• 5 onboard DSPs take the load off the computer’s main processor

• 2 analog inputs with 20-bit 128-times oversampling A/D converters

• 2 analog outputs with 20-bit 8-times oversampling D/A converters

• Stereo coaxial digital input and output (20- or 24-bit)

• Optional multi-channel analog and digital input and output options

Mixer

• 24 input channels, 8 bus outs, 6 aux sends (two feeding the onboard

effects processors), and a stereo output

• Input channels 21–24 function as effects returns for the onboard effects

• 4-band parametric EQ on all inputs channels and the stereo output

• Dynamics processors with reduction meters on all inputs channels and

the stereo output

• Two onboard effects processors with Yamaha ProR3/REV500 quality

• Input delay on input channels 1–20

• Signal level metering for all inputs and outputs

• Digital cascading of two DS2416 cards for 48-channel mixing

• 32-bit digital audio processing

Recorder

• 8-track simultaneous recording

• 16-track simultaneous playback

• Up to 32-bit recording and playback (software dependent)

• Sample-accurate synchronization between tracks

• External synchronization via controlling software

6

Connections

DS2416—Owner’s Manual

Connections

Rear

A

IN L, IN R

Analog IN L and IN R inputs feature phono jacks with a

nominal input level of –10 dBV. Analog to digital conversion

features 20-bit 128-times oversampling techniques. For best

performance use only shielded cables.

B

OUT L, OUT R

Analog OUT L and OUT R outputs feature phono jacks with

a nominal output level of –10 dBV. Digital to analog conver-

sion features 20-bit 8-times oversampling. For best perfor-

mance use only shielded cables.

C

D IN

This two-channel coaxial-type phono connection accepts

digital audio with a 24-bit maximum wordlength. Use con-

necting cables with a nominal impedance of 75 ohms.

D

D OUT

This two-channel coaxial-type phono connection outputs

digital audio with a 24-bit maximum wordlength. Use con-

necting cables with a nominal impedance of 75 ohms.

IN L

IN R

OUT L

OUT R

D IN

D OUT

1

2

3

4

Connections

7

DS2416—Owner’s Manual

Internal

A

SI (Serial In) connector

When two DS2416 cards are installed, this connector is connected to the “SO”

connector on the other card using the supplied 14-pin to 16-pin cable. Sound

cards that support the DS2416 can be connected directly to the mixer’s sub

inputs via this connector.

B

SO (Serial Out) connector

When two DS2416 cards are installed, this connector is connected to the “SI”

connector on the other card using the supplied 14-pin to 16-pin cable.

C

IO-A connector

This connector connects to the ﬁrst optional AX44 Audio Expansion Unit.

D

IO-B connector

This connector connects to the second optional AX44 Audio Expansion Unit.

IO

A

B

1 2 3 4

SI

SO

IO-A

IO-B

8

Installing the DS2416

DS2416—Owner’s Manual

Installing the DS2416

The DS2416 installs into a PCI expansion slot and requires no special jumper

settings or interrupt settings.

See your computer’s manual for full details on installing PCI cards.

1

Turn off the computer and disconnect the power cord.

2

Remove the computer’s cover.

3

Choose an empty PCI slot for the DS2416, and remove the screw

from its expansion-slot cover.

To prevent static electricity from damaging the DS2416, touch a grounded

metal part of your computer, such as the power supply case, before handling

it.

4

Carefully align and insert the DS2416 into the PCI slot.

5

Secure the DS2416 using the screw removed previously.

6

Replace the computer’s cover.

7

Turn on your computer.

8

When the New Hardware Found dialog box appears, select “Driver

from disk provided by hardware manufacturer”, and then click OK.

9

When the Install From Disk dialog box appears, insert the driver

ﬂoppy disk into the ﬂoppy disk drive, and then click OK.

10

When the restart dialog box appears, restart your computer.

Important: The DS2416 is grounded via the expansion-card ﬁxing screw, so

be sure to tighten it securely.

Testing the DS2416

9

DS2416—Owner’s Manual

Testing the DS2416

A test program is included with the DS2416 to make sure that the card, driver,

and DSPs are functioning correctly.

Installing the Test Program

1

Insert the supplied ﬂoppy disk into the ﬂoppy disk drive.

2

Double-click Setup.exe and follow the on-screen prompts.

The Test program and its associated ﬁles are installed.

Using the Test Program

1

From the Start menu, select Programs, DSP Factory, ds2416ck.exe.

2

When the Test program window appears, click the CHECK START

button to run the tests.

The Test program checks:

1. How many DS2416 cards are installed.

2. Whether the DS2416 drivers are installed

3. Whether the DSP chips are functioning correctly.

The test results appear as each test is completed. If all tests are successful, a

sine wave test tone can be produced through the OUT L, OUT R, D OUT, and

outputs 1 through 4 of any connected AX44s by clicking the test tone button.

If a test fails, follow the advice provided.

If the driver test fails again after restarting, try reinstalling the driver.

If the DSP test produces a “DSP ERROR” or “DSP NG” message, the DS2416

has a hardware problem and you should contact your Yamaha dealer.

3

Click the EXIT button to quit the Test program.

10

Wordclocks

DS2416—Owner’s Manual

Wordclocks

Unlike analog audio equipment, digital audio equipment must be synchro-

nized when digital audio is transferred from one device to another, otherwise,

the digital audio might not be read correctly and audible noise, glitches, or

clicks may occur. Synchronization is achieved using what’s called a wordclock,

which is a clock signal for synchronizing all the digital audio words in an

audio system. Note that wordclocks are not the same as SMPTE or MIDI

timecode, which are used to synchronize audio recorders, MIDI sequencers,

and so on. Wordclock synchronization refers to the synchronization of the

digital audio processing circuits inside each digital audio device.

In a typical digital audio system, one device acts as the wordclock master and

the other devices act as wordclock slaves, synchronizing to the wordclock

master. If the DS2416 is the only digital audio device in your system, no spe-

cial wordclock settings are required, as the DS2416 synchronizes to its own

internal wordclock. Add a DAT recorder or digital multitrack recorder, how-

ever, and you must decide which device to use as wordclock master and which

devices to use as slaves. Even when you’ve done this and conﬁgured your sys-

tem, it may sometimes be necessary to change the wordclock settings, such as

when recording from a DAT or CD player.

Wordclocks run at the same frequency as the sampling rate. The DS2416 gen-

erates its own wordclock at 44.1 kHz (the industry-standard sampling rate for

music CDs) or 48 kHz and can be used as wordclock master. Alternatively, it

can be used as a wordclock slave synchronized to an external wordclock of

between 30.08 kHz and 50.88 kHz (32 kHz –6% to 48 kHz +6%). Converting

the sampling rate of digital audio is a complicated process, so it’s best to use

the 44.1 kHz sampling rate, especially if your work is destined for CD distri-

bution.

Wordclock signals can be distributed via dedicated cables or derived from

standard digital audio connections, such as the D IN and D OUT connections

on the DS2416. With Coaxial digital audio connections, a wordclock signal is

transmitted even when no audio signal is present. The DS2416 can also trans-

mit and receive wordclock signals via its SI, SO, IO-A, and IO-B connectors.

In a system where all devices share a common wordclock, it’s important that

all devices be turned on even when they’re not being used. Turn on the word-

clock master ﬁrst, and then the slaves. When shutting down the system, turn

off the slaves ﬁrst, and then the master. Before commencing with a recording

session, make sure that all wordclock slaves are synchronized to the master.

Some devices have front panel indicators to show when they are wordclock

synchronized. Refer to the instructions for each device.

Wordclocks 11

DS2416—Owner’s Manual

Recording Digitally to the DS2416

In this example, a DAT deck is connected to the DS2416 D IN connector for

digital recording. The DS2416 works as wordclock slave, deriving its word-

clock from the D IN connection, and the DAT works as wordclock master.

Recording Digitally to DAT

In this example, the D OUT connector on the DS2416 is connected to the dig-

ital input of a DAT recorder for digital mixdown recording. The DS2416

works as wordclock master and the DAT works as wordclock slave. When the

digital input on the DAT recorder is selected as the recording source, the DAT

should automatically synchronize to the wordclock signal coming from the

DS2416. On some DAT recorders, the wordclock source may have to be set

separately. Refer to the instructions supplied with your DAT recorder.

IN L

IN R

OUT L

OUT R

D IN

D OUT

DAT

00.00.00.00

Digital Out

DAT recorder

(wordclock master)

DS2416

(wordclock slave

Source = D IN)

IN L

IN R

OUT L

OUT R

D IN

D OUT

DAT

00.00.00.00

Digital In

DAT recorder

(wordclock slave)

DS2416

(wordclock master)

12 Digitally Cascading DS2416 Cards

DS2416—Owner’s Manual

Digitally Cascading DS2416 Cards

Using the digital “SI” and “SO” connectors, two DS2416 cards can be digitally

cascaded for common busing and 48-channel mixing.

1 Install the second DS2416 into a PCI slot adjacent to the ﬁrst

DS2416, as explained previously.

2 Using the supplied 14-pin to 16-pin cables, connect the “SI” and

“SO” connectors as shown below.

3 Replace the computer’s cover.

DS2416 (A) DS2416 (B)

I

O

I

O

DS2416 (A) DS2416 (B)

I

O

In this example, the buses of DS2416

(A) and (B) are linked together for 48-

channel mixing. Individual buses from

DS2416 (B) can alternatively be fed to

the sub inputs of DS2416 (A).

In this example, the buses of DS2416

(A) and (B) are linked together for 48-

channel mixing. Individual buses from

either DS2416 can be fed to the other

DS2416.

DS2416 Q&A (Questions & Answers) 13

DS2416—Owner’s Manual

DS2416 Q&A (Questions & Answers)

Q What’s a DSP?

A A DSP, or Digital Signal Processor is a processor optimized for

real-time digital data processing. The DS2416 features the same

DSP as the Yamaha 02R and 03D digital mixing consoles and

ProR3 and REV500 effects processors.

Q At what wordlength is digital audio processed?

A The EQ features a 44-bit data path, 32-bit coefﬁcient, and 54-bit

accumulator. All other mixer sections feature a 32-bit data path,

24-bit coefﬁcient, and 42-bit accumulator.

Q Does the DS2416 have any onboard memory?

A Yes, 3 megabytes, which is used for input, and effects delays.

Q What is the available recording time?

A This depends on the software, selected wordlength, and hard disk

space. In general, two channels of 16-bit digital audio use 10.6

MB/min.

Q How do I synchronize the DS2416 to MIDI Clock, MTC, or SMPTE

timecode?

A If the software and timecode interface support external timecode,

so does the DS2416.

Q Can DS2416 mixer functions be controlled via MIDI?

A If the controlling software supports this, yes.

Q How good are the onboard effects processors?

A As good as those used in the Yamaha ProR3 and REV500 effects

processors.

Q Can the DS2416 be used simultaneously with a Sound Blaster or

Korg 1212 I/O card?

A Yes.

14 Troubleshooting

DS2416—Owner’s Manual

Troubleshooting

Trouble Advice

The DS2416 does not work?

Make sure that the DS2416 is inserted in the

PCI bus slot correctly.

Make sure that the DS2416 input and outputs

are correctly assigned using the controlling

software.

In older computers, some PCI slots may not

function as the bus master, and the DS2416 will

not work in such slots. See your computer’s

manual for more details.

Some PCI cards may conﬂict with the DS2416.

Try removing cards, or swapping slots with the

DS2416.

A low-level hum can be heard?

The DS2416 is grounded via the expan-

sion-card ﬁxing screw, so be sure to tighten it

securely.

Effects Programs 15

DS2416—Owner’s Manual

Effects Programs

The DS2416 provides the following effects programs. Detailed effects param-

eters are shown on page 149.

Reverb-type Effects

Delays

Type Description

REVERB HALL Reverb simulating a large space such as a concert hall.

REVERB ROOM Reverb simulating the acoustics of a smaller space than REVERB HALL.

REVERB STAGE Reverb designed with vocals in mind.

REVERB PLATE

Simulation of a metal-plate reverb unit, producing a feeling of

hard-edged reverberation.

EARLY REF.

An effect which isolates only the early reﬂection (ER) component from

reverberation. A ﬂashier effect than reverb is produced.

GATE REVERB A type of ER designed for use as gated reverb.

REVERSE GATE A reverse-playback type ER.

Type Description

MONO DELAY

Mono delay with simple operation. Use when you don't need to use

complex parameter settings.

STEREO DELAY Stereo delay with independent left and right.

MOD.DELAY Mono delay with modulation.

DELAY LCR Three-tap delay (L, C, R).

ECHO

Stereo delay with additional parameters for more detailed control. The

signal can be fed back from left to right, and right to left.

16 Effects Programs

DS2416—Owner’s Manual

Modulation-type Effects

Guitar Effects

Dynamic Effects

Type Description

CHORUS Three-phase stereo chorus.

FLANGE The well-known ﬂanging effect.

SYMPHONIC

A Yamaha proprietary effect that produces a richer and more complex

modulation than chorus.

PHASER Stereo phaser with 2–16 stages of phase shift.

AUTO PAN An effect which cyclically moves the sound between left and right.

TREMOLO Tremolo

HQ.PITCH

(Effect 2 only)

Only one note is pitch-shifted, but a stable effect is produced.

DUAL PITCH Stereo pitch shift with left and right pitches set independently.

ROTARY Simulation of a rotary speaker.

RING MOD.

An effect that modiﬁes the pitch by applying amplitude modulation to

the frequency of the input.

MOD.FILTER An effect which uses an LFO to modulate the frequency of the ﬁlter.

Type Description

DISTORTION Distortion

AMP SIMULATE Guitar Amp Simulator

Type Description

DYNA.FILTER Dynamically controlled ﬁlter.

DYNA.FLANGE Dynamically controlled ﬂange.

DYNA.PHASER Dynamically controlled phase shifter.

Effects Programs 17

DS2416—Owner’s Manual

Combined Effects

Type Description

REV+CHORUS Reverb and chorus in parallel

REV->CHORUS Reverb and chorus in series

REV+FLANGE Reverb and ﬂange in parallel

REV->FLANGE Reverb and ﬂange in series

REV+SYMPHO. Reverb and symphonic in parallel

REV->SYMPHO. Reverb and symphonic in series

REV->PAN Reverb and auto-pan in parallel

DELAY+ER. Delay and early reﬂections in parallel

DELAY->ER. Delay and early reﬂections in series

DELAY+REV Delay and reverb in parallel

DELAY->REV Delay and reverb in series

DIST->DELAY Distortion and delay in series

18 Block Diagram

DS2416—Owner’s Manual

Block Diagram

SAME AS CH1

CH1

CH2-8

SAME AS CH1

CH9-12

SAME AS CH1

CH13-16

SAME AS CH1

CH17

SAME AS CH1

CH18

SAME AS CH1

CH19

SAME AS CH1

CH20

A/D

CHANNEL

METER

ON

REDUCTION

METER

Signal

Pre

Post

SAME AS CH21

CH21

SAME AS CH21

CH22

SAME AS CH21

CH23

CH24

STEREO

MASTER

CASCADE IN(16ch)

SUB IN(8ch)

PCI

PLAYBACK(16ch)

IO-B

IO-A

PCI

SI

A IN L

A IN R

D IN

IO-A IN(4 or 8ch)

IO-B IN(4 or 8ch)

SERIAL IN

16 or 8

16

8

16

4 or 8

4

2

7

4

4 or 8

4

4 4

8

7

78

4

DC-CUT

ATT/PHASE

4BAND

PEQ

DYNAMICS

DE-EMPHASIS

CHANNEL

METER

ON

REDUCTION

METER

Signal

Pre

Post

DC-CUT

ATT/PHASE

4BAND

PEQ

DYNAMICS

DELAY

BALANCE

Strona jest ładowana ...

Yamaha DS2416 Instrukcja obsługi

Yamaha DS2416 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty