Yamaha DVD-S795 Instrukcja obsługi

Marka: Yamaha

Model: DVD-S795

Kategoria: Odtwarzacze DVD

Typ: Instrukcja obsługi

DVD/Video CD/CD Player

DVD-S795

Operating Instructions

Before attempting to connect, operate or adjust this product,

please read this Operating Instructions manual completely

and save this manual for future reference.

VQT8007-1

Safety information

Note:

This player can be used only where the power supply

is AC 120 V, 60 Hz. It cannot be used elsewhere.

CAUTION:

DVD/VIDEO CD/CD PLAYER IS A CLASS I LASER

PRODUCT. HOWEVER THIS DVD/VIDEO CD/CD

PLAYER USES A VISIBLE LASER BEAM WHICH

COULD CAUSE HAZARDOUS RADIATION EXPO-

SURE IF DIRECTED. BE SURE TO OPERATE THE

DVD/VIDEO CD/CD PLAYER CORRECTLY AS IN-

STRUCTED.

WHEN THIS DVD/VIDEO CD/CD PLAYER IS

PLUGGED TO THE WALL OUTLET, DO NOT

PLACE YOUR EYES CLOSE TO THE OPENING

OF THE DISC TRAY AND OTHER OPENINGS TO

LOOK INTO THE INSIDE OF THIS PLAYER.

USE OF CONTROLS OR ADJUSTMENTS OR PER-

FORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR

YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS PLAYER TO

RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, AND ANNOYING INTERFERENCE, USE

THE SUPPLIED ACCESSORIES ONLY.

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated “dangerous volt-

age” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral trian-

gle is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the ap-

pliance.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PER-

SONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION -LASER RADIATION WHEN OPEN.

DO NOT STARE INTO BEAM.

ATTENTION-RAYONNEMENT LASER EN CAS D'OUVERTURE.

NE PAS REGARDER DANS LE FAISCEAU.

VORSICHT -LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.

NICHT IN DEN STRAHL BLICKEN.

ADVARSEL -LASERSTRÅLING VED ÅBNING.

SE IKKE IND I STRÅLEN.

ADVARSEL -LASERSTRÅLING NÅR DEKSEL ÅPNES.

STIRR IKKE INN I STRÅLEN.

VARNING -LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.

STIRRA EJ IN I STRÅLEN.

VARO! -AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE.

ÄLÄ TUIJOTA SÄTEESEEN.

(Inside of player)

This player is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this player itself is turned off. This state is

called the standby mode.

In this state, this player is designed to consume a

very small quantity of power.

FOR CANADIAN CUSTOMERS

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT AND FULLY

INSERT.

THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003.

Getting Started

FCC INFORMATION (for U.S.A)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the in-

structions contained in this manual, meets FCC require-

ments. Modifications not expressly approved by Yamaha

may void your authority, granted by the FCC, to use the

product.

IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded ca-

bles. Cable/s supplied with this product MUST be used. Fol-

low all installation instructions. Failure to follow instructions

could void your FCC authorization to use this product in the

USA.

NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential enviroment will not result

in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices.

Compliance with FCC regulations does not guarantee that in-

terference will not occur in all installations. If this product is

found to be the source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affect-

ed by the interference.

Utilize power outlets that are on different branch (circuit

breaker of fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory re-

sults, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate re-

tailer, please contact Yamaha Electronics Corp., U.S.A. 6600

Orangethorpe Ave, Buena Park, CA 90620

The above statement apply ONLY to those products distribut-

ed by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the

most out of your equipment by playing it at a safe lev-

el. One that lets the sound come through loud and

clear without annoying blaring or distortion—and,

most importantly, without affecting your sensitive

hearing. Since hearing damage from loud sounds is

often undetectable until it is too late,

YAMAHA and the Electronic Industries

Association’s Consumer Electronics

Group recommend you to avoid

prolonged exposure from excessive

volume levels.

Precautions

Please read these precautions before operating this player.

È AC cord

To avoid any malfunctions of the player, and to protect against

electric shock, fire or personal injury, please observe the fol-

lowing:

ÁHold the plug firmly when connecting or disconnecting

the AC cord to this player.

ÁDo not connect or disconnect the AC cord when your

hands are wet.

ÁKeep the AC cord away from heating appliances.

ÁNever put any heavy object on the AC cord.

ÁDo not attempt to repair or reconstruct the AC cord in

any way.

ÁRemove dust, dirt, etc. on the plug at regular intervals.

ÁIf the player has been dropped or otherwise damaged,

set the player to the standby mode and disconnect the

AC cord.

ÁIf smoke, malodors or noises are emitted from the play-

er, set the player to the standby mode and disconnect

the AC cord.

È Placement

Avoid placing the player in areas of:

Ádirect sunlight or heating radiators, or closed automobiles

Áhigh temperature [over 95uF (35uC)] or high humidity (over

90%)

Áexcessive dust

Ávibration, impact or where the surface is tilted as the internal

parts may be seriously damaged.

ÁPlace the player in a horizontal position, and do not place

anything heavy on it.

ÁDo not place the player on amplifiers or other equipment

which may become hot.

È Non-use periods

When the player is not being used, set the player to the stand-

by mode.

When left unused for a long period of time, the player should

be unplugged from the household AC outlet.

È Do not place objects inside the player

ÁTouching internal parts of this player is dangerous, and may

cause serious damage to the player. Do not attempt to disas-

semble the player.

ÁDo not put any foreign object on the disc tray.

È Keep away from water and magnets.

ÁKeep the player away from flower vases, tubs, sinks, etc. If

liquids are spilled into the player, serious damage could

occur.

ÁKeep magnetic objects such as speakers, at a distance from

the player.

È Condensation

Moisture may form on the lens in the following conditions:

Áimmediately after a heater has been turned on.

Áin a steamy or very humid room.

Áwhen the player is moved from a cold environment to a warm

one.

If moisture forms inside this player, it may not operate proper-

ly. In this case, turn on the power and wait about one hour for

the moisture to evaporate.

È When watching a TV broadcast

Depending on the reception condition of the TV, interference

may appear on the TV screen while you are watching a TV

broadcast and the player is left on. This is not a malfunction of

the player or the TV. To watch a TV broadcast, set the player

to the standby mode.

Dear Customers

May we take this opportunity to thank you for purchasing this

YAMAHA DVD/Video CD/CD player.

We strongly recommend that you carefully study the Operating

Instructions before attempting to operate the player and that

you note the listed precautions.

Accessories

Please check and identify the

supplied accessories.

Remote control

unit . . . . . . . . . . . . . . 1

Batteries . . . . . . . . . 2

for remote control unit

[size “AA”]

AC cord . . . . . . . . . . 1

Video/audio

cable . . . . . . . . . . . . 1

The model number and serial number of this player can

be found on either the back or the bottom of the player.

Please note them in the space provided below and re-

tain this booklet as a permanent record of your purchase

to aid identification in the event of theft.

MODEL NUMBER__________________________

SERIAL NUMBER__________________________

This product incorporates copyright protection technolo-

gy that is protected by method claims of certain U.S. pat-

ents and other intellectual property rights owned by

Macrovision Corporation and other rights owners. Use of

this copyright protection technology must be authorized

by Macrovision Corporation, and is intended for home

and other limited viewing uses only unless otherwise au-

thorized by Macrovision Corporation. Reverse engineer-

ing or disassembly is prohibited.

Getting StartedBasic OperationOperation Using

On-Screen Menu Icons

Advanced OperationInitial SettingsFor Your Reference

Table of contents

Getting Started:

Safety information . . . . . . . . . . . . . . . . . . . . . 02

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

Definition of terms . . . . . . . . . . . . . . . . . . . . . 7

Control reference guide . . . . . . . . . . . . . . . . . 08

ÁMain unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 008

ÁRemote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 008

Front panel FL display . . . . . . . . . . . . . . . . . . 09

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ÁConnecting to an AV amplifier containing Dolby Digital

or dts (digital theater systems) decoder . . . . . . . . . . . . . 010

ÁConnecting to an AV amplifier which does not contain

Dolby Digital or dts (digital theater systems)

decoder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 012

Remote control unit preparation . . . . . . . . . . 13

ÁBattery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 013

ÁRemote control operation range . . . . . . . . . . . . . . . . . . . 013

Connecting headphones . . . . . . . . . . . . . . . . 13

Basic Operation:

Basic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ÁBefore enjoying DVD/Video CD/CD . . . . . . . . . . . . . . . . 014

ÁBasic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 014

ÁStopping play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 015

Skipping ahead or back . . . . . . . . . . . . . . . . . 16

Still picture (Pause) . . . . . . . . . . . . . . . . . . . . 16

Rapid advance (Rapid reverse) . . . . . . . . . . . 17

Frame advance (Frame reverse)

[DVD/Video CD] . . . . . . . . . . . . . . . . . . . . . . . . 17

Slow-motion play

[DVD/Video CD] . . . . . . . . . . . 17

Enjoying Video CDs with playback control

without using menus

[Video CD] . . . . . . . . . 17

Operation Using On-Screen Menu Icons:

General information about On-Screen Menu

Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ÁCommon procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 018

Detailed descriptions of each On-Screen

Menu Icon. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

ÁScreen for disc information (For DVD) . . . . . . . . . . . . . . 019

ÁScreen for disc information (For Video CD/CD) . . . . . . . 020

ÁScreen for player information . . . . . . . . . . . . . . . . . . . . . 021

ÁShuttle screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 022

Advanced Operation:

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ÁRepeat viewing (listening) . . . . . . . . . . . . . . . . . . . . . . . 023

ÁRepeating sections between two specific points

(A-B repeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 024

Program play [Video CD/CD] . . . . . . . . . . . . . . . . . . 25

Random play

[Video CD/CD] . . . . . . . . . . . . . . . 26

Storing markers in memory to be viewed

(listened to) again . . . . . . . . . . . . . . . . . . . . 26

ÁStoring a marker in the memory . . . . . . . . . . . . . . . . . . . 026

ÁRecalling/clearing a marker . . . . . . . . . . . . . . . . . . . . . . 027

Changing audio soundtrack language

[DVD] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Switching vocals ON or OFF for Karaoke

discs

[DVD/Video CD] . . . . . . . . . . . . . . . . . . . 27

Changing subtitle language

[DVD] . . . . . . . . . 28

Viewing from another angle

[DVD] . . . . . . . . . 29

Using a title menu

[DVD] . . . . . . . . . . . . . . . . . 29

Using a DVD menu

[DVD]. . . . . . . . . . . . . . . . . 29

Initial Settings:

Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . 30

ÁCommon procedures of initial settings . . . . . . . . . . . . . . 030

ÁSelecting disc languages [DVD] . . . . . . . . . . . . . . . . . . . 031

ÁSelecting rating level [DVD] . . . . . . . . . . . . . . . . . . . . . . 032

ÁSelecting language of On-Screen Display menu . . . . . . 033

ÁSelecting the display format of the On-Screen

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 034

ÁSelecting the FL display brightness . . . . . . . . . . . . . . . . 035

ÁSelecting TV screen type . . . . . . . . . . . . . . . . . . . . . . . . 036

ÁConcerning images which appear on the TV screen

(aspect ratios of the screen) . . . . . . . . . . . . . . . . . . . . . . 037

ÁSelecting digital output . . . . . . . . . . . . . . . . . . . . . . . . . . 038

ÁSpeaker settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

ÁOther settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 042

Language code list . . . . . . . . . . . . . . . . . . . . . 44

For Your Reference:

Disc handling and maintenance . . . . . . . . . . 45

ÁMaintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 045

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 46

ÁSelf-diagnosis display function . . . . . . . . . . . . . . . . . . . . 047

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 48

Features

È High picture quality

Á10 bit video D/A converter

With its 10 bit capability, this D/A converter reproduces fine

images faithfully.

ÁComponent video output

When used with a compatible monitor, a video connection via

the component video output jacks of your new DVD/Video CD/

CD player is capable of the most precise color reproduction in

a video signal.

ÁAn array of picture quality modes yielded by digital

processing

Signal deterioration is kept to the minimum by processing the

data as digital data.

This feature can be used as the picture quality setting individ-

ually tailored for DVD playback.

–Cinema Image (See page 21.)

Using the On-Screen Menu Icon enables the cinema mode,

which is best for the playback of movie programs, to be se-

lected.

In addition, the picture quality best suited to the type of soft-

ware programs concerned can be selected. In all, four pic-

ture quality modes are provided: normal, soft, fine and

cinema.

–User selection (See page 21.)

Using the On-Screen Menu Icon, the contrast, color hue,

equalizer and brightness can be adjusted to suit your own

preference.

–Monitor selector (See page 36.)

Once the type of TV used [Standard (Direct View TV), CRT

Projector, LCD Projector, Projection TV] has been selected

when the initial setting operations are performed, the opti-

mum picture quality for the type of TV concerned will be

automatically selected.

È High sound quality

Á96 kHz/24 bit audio D/A converter

This player enables 96 kHz/24 bit linear PCM signals, which

constitute the highest specifications in the DVD standards, to

be reproduced faithfully. To support 96 kHz sampling/24 bit

sound, the shaping noise of this multi-level digital sigma type

of D/A converter is kept flat up to 44 kHz, thus preventing the

important audio signals from being affected in any way. In

terms of the bottom line, the sound in all of its various modes

is reproduced faithfully.

ÁDolby Digital 5.1ch surround decoder

(See pages 21 and 40.)

The Dolby Digital 5.1ch surround decoder incorporated in

this player comes with speaker mode settings which support

the low-range reproduction capability of the speakers, speak-

er level settings, delay time settings, audio dynamic range

suppression, Cinema Dialogue function to make it easier to

hear movie dialogues, and other features.

Ádts (digital theater systems) digital output (See page 10.)

By connecting an amplifier incorporating a dts decoder, you

can enjoy high quality digital surround from dts discs.

È On-Screen Menu Icons (See page 18.)

By simply pressing the ON SCREEN button on the remote

control, information on the DVD/Video CD/CD player and disc

can be displayed on the TV screen for easy identification. The

player’s operations and settings can be easily accessed by

operating the cursor buttons on the remote control while moni-

toring the TV screen. The color and position of the On-Screen

Menu Icons can be changed.

È Versatile DVD features

ÁMulti-audio function (See page 27.)

The audio soundtrack can be heard in up to 8 languages.

(The number of audio sound languages depends on the soft-

ware.)

ÁMulti-subtitle function (See page 28.)

Subtitles may be displayed in one of a maximum of 32 lan-

guages. (The number of the subtitle languages depends on

the software.)

ÁMulti-angle function (See page 29.)

This function allows you to choose the viewing angle of

scenes which were shot from a number of different angles.

(Limited to DVD recorded with multiple camera angles.)

ÁParental lock function (See page 32.)

This function can prevent playback of DVD software unsuita-

ble for some audiences (especially for children).

È Marker function (See page 26.)

This player can store a maximum of 5 positions in memory, for

convenient access, as desired.

È Disc formats supported by this player

The player can play back discs bearing any of the following

marks:

È Discs which cannot be played with this

player

ÁDVD with Region No. other than “1” or “ALL”

ÁDisc of PAL system ÁCD-G

ÁDVD-ROM ÁCD-RW

ÁDVD-R/DVD-RAM ÁDVDoRW

ÁCD-ROM ÁCVD

ÁVSD ÁSVCD

ÁCDV ÁDivx Video Disc

etc.

ÁDo not try to play Photo CD or CD-R.

(Otherwise, data on the disc may be damaged.)

È Region Management Information

This player is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD

disc. The Region number of this player is “1”. If the Region

number described on the DVD disc does not correspond to the

Region number of this player, this player cannot play this disc.

This player will play DVD discs made for “ALL” Regions. This

player will play DVD discs marked with the following symbols:

DVD

[3w (8 cm) disc/

5w (12 cm) disc]

Video CD

[3w (8 cm) disc/

5w (12 cm) disc]

[3w (8 cm) disc/

5w (12 cm) disc]

ALL

Getting Started

Angle

Recorded onto some DVD discs are scenes which have been

simultaneously shot from a number of different angles (the

same scene is shot from the front, from the left side, from the

right side, etc.). With such discs, the ANGLE button can be

used to view the scene from different angles.

Chapter number

These numbers are recorded on DVD discs. A title is subdivid-

ed into many sections, each of which is numbered, and specif-

ic parts of video presentations can be searched quickly using

these numbers.

Digital audio output connector (Optical)

The digital audio output connector (optical) converts electrical

signals into optical signals and transfers them to the amplifier.

Consequently, it has a number of features including its immu-

nity from electrical interference from external sources and its

ability to prevent the generation of noise and its minimal effect

on the external environment.

DVD

This refers to a high-density optical disc on which high-quality

pictures and sound have been recorded by means of digital

signals. Incorporating a new video compression technology

(MPEG 2) and high-density recording technology, DVD en-

ables esthetically pleasing full-motion video to be recorded

over long periods of time (for instance, a whole movie can be

recorded).

DVD has a structure consisting of two 0.6 mm thin discs which

are adhered to each other. Since the thinner the disc, the high-

er the density at which the information can be recorded, a DVD

disc has a greater capacity than a single 1.2 mm thick disc.

Since the two thin discs are adhered to each other, there is the

potential to achieve double-sided play sometime in the future

for even longer duration of play.

Field

Half of the video information (video signal) in a frame is called

a field. With conventional TV systems, a signal frame (a single

screen) consists of two fields.

Field still

Only one field (half of the video information) is displayed on the

TV screen, so the apparent resolution is low. However, there is

no blurring on the screen.

Frame

Individual images in a video or on the TV are called frames.

Frame still

The two fields are displayed, alternately, on the TV screen, so

the image is blurry. However, the image quality is better than

field images.

Playback control

This is recorded on a Video CD (version 2.0). The scenes or

information to be viewed (or listened to) can be selected inter-

actively with the TV monitor by looking at the menu shown on

the TV monitor.

Subtitles

This is the appearance of the dialogue at the bottom of the

screen which are prerecorded on some DVD discs.

Title number

These numbers are recorded on DVD discs. When a disc con-

tains two or more movies, these movies are numbered as title

1, title 2, etc.

Track number

These numbers are assigned to the tracks which are recorded

on Video CDs and CDs. They enable specific tracks to be lo-

cated quickly.

Video CD

This contains recordings of pictures and sound whose quality

is on a par with that of videotape. This player also supports

Video CDs with playback control (version 2.0).

Definition of terms

Remote control unit

Page

e POWER button (*/I) . . . . . . . . . . . . . . . . . . . . . . . . . . 14

f STOP button (@) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

g SKIP buttons (H, I). . . . . . . . . . . . . . . . . . . . 15, 16

h TITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 29

i Cursor buttons (A, B, C, D)/SELECT button . . . . . 15

j ON SCREEN button . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

k AUDIO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

l SUBTITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

m MARKER button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

n PLAY MODE button . . . . . . . . . . . . . . . . . . . . . . . . 25, 26

o REPEAT button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

p CLEAR button. . . . . . . . . . . . . . . . . . . . . . . 18, 21, 25, 27

q A-B button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

r SET UP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

s OPEN/CLOSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 14

t STILL/PAUSE button (g). . . . . . . . . . . . . . . . . . . . . . . 16

u PLAY button (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

v SLOW/SEARCH buttons (F, G) . . . . . . . . . . . . . . 17

w MENU button . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 17, 29

x RETURN button . . . . . . . . . . . . . . . . . . . . . . . . 15, 18, 30

y ANGLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

z Numeric buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ÁTo select a 2-digit number

Example: To select track 23

Press “X10”, “2” and then “3”.

Control reference guide

Main unit

Page

e STANDBY/ON button . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Press to switch the player from standby mode to ON or vice

versa. In standby mode, the player is still consuming a

small amount of power.

f Disc tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

g OPEN/CLOSE button (E) . . . . . . . . . . . . . . . . . . . . . . . 14

h PLAY button (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

i PAUSE button (g) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Page

j STOP button (@) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

k Headphones jack (PHONES) . . . . . . . . . . . . . . . . . . . . 13

l Phones level control (LEVEL) . . . . . . . . . . . . . . . . . . . 13

m Remote control signal sensor. . . . . . . . . . . . . . . . . . . 13

n FL Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

o SKIP buttons (H, I). . . . . . . . . . . . . . . . . . . . 15, 16

p SEARCH buttons (F, G) . . . . . . . . . . . . . . . . . . . . 17

NATURAL SOUND DVD PLAYER

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

SKIP

;

D I G I T A L

1fghij

ponmlk

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

Getting Started

Front panel FL display

e Rotates during play.

Rotates fast clockwise or counterclockwise

during rapid advance (reverse). (See page 17.)

Rotates slowly clockwise or counterclockwise

during slow-motion play.

[DVD/Video CD] (See page 17.)

Illuminates in the stop mode.

f Illuminates during playback.

Flashes when the RESUME function is ON.

(See page 15.)

g Illuminates during repeat play. (See pages 23 and 24.)

h Illuminates in the still picture (pause) mode.

(See page 16.)

i Indicates the title/chapter number. [DVD]

Indicates the track number. [Video CD/CD]

j Indicates the elapsed playing time from the start of the

title/track during play.

k Indicates the audio channel information recorded in the

disc being played back (e.g. 2ch or 5.1ch).

l Illuminates when a DVD is loaded.

m Illuminates when it is possible to switch the angle.

[DVD] (See page 29.)

n Illuminates during program play. [Video CD/CD]

(See page 25.)

o Illuminates when Linear PCM of 96 kHz sampling is be-

ing played.

p Illuminates when Linear PCM of 24 bit is being played.

q Illuminates when the disc tray is open.

r Illuminates when the disc tray is being closed (re-

tracted).

s Illuminates during play of a DVD.

t Illuminates during play of an interactive DVD.

u Illuminates during play of a Karaoke DVD.

v Illuminates during play of an interactive Karaoke DVD.

w Illuminates during play of a Video CD.

x Illuminates during play of a Video CD with playback

control.

y Illuminates during play of a CD.

z Illuminates when the track number is selected to be

stored in the memory (program play). [Video CD/CD]

(See page 25.)

{ Illuminates when playback is impossible.

ÁDVD for which playback is prohibited by the initial settings

“2 Ratings”. (See page 32.)

ÁDVD with Region No. other than “1” or “ALL”

Á(See page 6.)

ÁDisc of PAL system

| Illuminates when no disc is loaded.

An interactive DVD is DVD software which includes multi-

ple angles, multiple plot endings, etc.

Surround (L)

Front (L)

Center

Surround (R)

Subwoofer

Front (R)

DVD

PROG.

ANGLE

96kHz 24bit

1 3 5 642

89 o0 p

{

DVD

PROG.

Connection

ÁEnsure that this player and other equipment to be connected are set to the standby mode or off, and disconnect the AC cord, before commencing

connection.

ÁDo not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.

ÁRead through the instructions before connecting other equipment.

ÁEnsure that you observe the color coding when connecting audio and video cables.

ÁSelect the appropriate screen type at the initial setting “6 TV Aspect” according to your TV set [4:3/16:9 and Standard (Direct View TV)/CRT Projector/

LCD Projector/Projection TV]. (See page 36.)

Notes:

ÁIf the DVD/Video CD/CD player is connected to the TV through a video cassette recorder, the picture may not be played back normally with some

DVDs.

ÁWhen playing some DVD discs, TV volume level may be lower than from some other sources, adjust the TV volume to your desired level.

ÁWhen the DVD/Video CD/CD player is connected to the TV set through the component video output connectors, the ON SCREEN informations from

the amplifier will not show on the TV screen. To show them, select the input position which is connected to the amplifier on the TV set.

Do not place the player on amplifiers or other equipment which may become hot.

Connecting to an AV amplifier containing Dolby Digital or dts (digital theater systems)

decoder

When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream is output from the player’s OPTICAL

digital audio output connector or COAXIAL digital audio output connector. When the player is connected to a Dolby Digital decoder or

dts decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable or coaxial digital audio cable (both

optional) is required when an optional Dolby Digital decoder or dts decoder is used.]

Note:

ÁWhen connecting an AV amplifier which contains dts decoder, be sure to select “Bitstream” at “3 dts” of the initial setting “7 Digital

Audio Output”. (“Off” is selected at the factory preset.) If “Off” is selected, dts bitstream is not output from the digital audio output

connector.

Video cable (optional)

Direction of

signal flow

TV set (optional)

Coaxial digital

audio cable

(optional)

Optical

digital

audio cable

(optional)

Video/audio

cable

(supplied)

S video

cable

(optional)

DVD/Video CD/CD player

AC cord (supplied)

To AC outlet

To component video input

connectors (Y, C

B, CR)

COAXIAL

DVD/LD

OPTICAL

DVD/

AUDIO SIGNAL

R L VIDEO S-VIDEO

VIDEO SIGNAL

PCM/U DIGITAL

DTS

COAXIAL

AUDIO OUT

OPTICAL

SUBWOOFER

CENTER SURROUND

6CH DISCRETE

MIXED 2CH

VIDEO

MAIN

S VIDEO

YCB CR

VIDEO OUT

COMPONENT VIDEO

AC IN

AV amplifier with

Dolby Digital/dts

decoder (optional)

Getting Started

Dust protection cap

Component video output connectors (Y, C

B, CR)

The component video output connector outputs the color dif-

ference signals (C

B, CR) and luminance signal (Y) separately in

order to achieve high fidelity in reproducing colors.

ÁThe description of the component video input connectors

may differ depending on the TV set or monitor (e.g. Y, P

B, PR/

Y, B-Y, R-Y/Y, C

B, CR and so on). Refer to the instruction

manual of your TV set for details.

S video output connector

The S video output connector separates the color (C) and lu-

minance (Y) signals before transmitting them to the TV set in

order to achieve a sharper picture.

Use the S video cable (optional) when connecting the player to

a TV set equipped with an S video input connector for the best

picture clarity possible.

Notes when connecting the optical digital audio cable

(optional)

ÁRemove the dust protection cap from the optical digital audio

output connector and connect the cable firmly so that the

configurations of both the cable and the connector match.

ÁKeep the dust protection cap and, to protect against dust, al-

ways reattach the cap when not using the connector.

Concerning the audio output from the player’s optical/

coaxial digital audio output connector

The type of audio output from the connector can be selected

by “7 Digital Audio Output” of the initial settings.

(See page 38.)

Compressed sound converted to PCM will be output.

Disc

DVD

Video

Sound

recording

format

Dolby Digital

Linear PCM

(48/96 kHz

16/20/24 bit)

dts

MPEG 1

Linear PCM

Optical/coaxial digital

audio output from

connector

Dolby Digital bitstream

(1–5.1ch) or PCM (2ch)

(48 kHz/16 bit)

\1 \2

Linear PCM (2ch)

(48 kHz sampling/16 bit

only) or no output

dts bitstream (1–5.1ch) or

no output

PCM

(44.1 kHz sampling)

Linear PCM

(44.1 kHz sampling)

Caution for the optical/coaxial digital audio output

connector:

È When connecting an amplifier (with an optical/

coaxial digital input connector) which contains

the Dolby Digital decoder or dts decorder

ÁBe sure to select “Bitstream” both at “2 Dolby Digi-

tal” and “3 dts” of the initial setting “7 Digital Audio

Output”. (See page 38.)

È When connecting an amplifier (with an optical/

coaxial digital input connector) which does not

contain the Dolby Digital decoder or dts de-

coder

ÁBe sure to select “PCM” at “2 Dolby Digital” and

“Off” at “3 dts” of the initial setting “7 Digital Audio

Output”. (See page 38.)

ÁOtherwise any attempt to play DVDs may cause

such a high level of noise that it may be harmful to

your ears and damage your speakers.

ÁVideo CDs and CDs can be played as they would

normally be played.

Note:

ÁSome dts decoders which do not support DVD-dts interface

may not work properly with the DVD/Video CD/CD player.

For your reference:

ÁDolby Digital is a digital sound compression technique devel-

oped by the Dolby Laboratories, Inc.

Supporting 5.1-channel surround sound, as well as stereo

(2-channel) sound, this technique enables a large quantity

of sound data to be efficiently recorded on a disc.

ÁLinear PCM is a signal recording format used in a CD. While

a CD is recorded in 44.1 kHz/16 bit, a DVD is recorded in

48 kHz/16 bit up to 96 kHz/24 bit.

ÁIf you have a Dolby Pro Logic Surround decoder, you will

obtain the full benefit of Pro Logic from the same DVD mov-

ies that provide full 5.1-channel Dolby Digital soundtracks, as

well as from titles with the Dolby Surround mark.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories. Confidential Unpublished Works.

j 1992–1997 Dolby Laboratories, Inc. All rights re-

served.

Connection

Connecting to an AV amplifier which does not contain Dolby Digital or dts (digital theater

systems) decoder

This DVD/Video CD/CD player contains a Dolby Digital decoder. This enables the playback of DVDs recorded in Dolby Digital Sur-

round or Linear PCM without the need for an optional decoder with Dolby Digital or Linear PCM processing. When the DVD/Video CD/

CD player is connected to an AV amplifier with 5.1ch input connectors, you can enjoy theater-quality audio in your home when playing

discs recorded in Dolby Digital Surround or Linear PCM.

TV set (optional)

Video/audio

cord

(supplied)

DVD/Video CD/CD player

Audio cord

(optional)

Notes:

ÁAfter connection is made, set the “8 Speaker Setting” (such

as Yes/No and Large/Small) according to your speaker sys-

tem. (See page 40.)

ÁIf the surround speakers are set to “No” at the “8 Speaker

Setting” (see page 40), the discs recorded in Linear PCM will

be played back only in 2 channels even when the center

speaker is connected as well as the front speakers.

ÁDVDs recorded in Linear PCM/96 kHz sampling in which

“Center Speaker” is contained will also be played back only

in 2 channels.

ÁIf the player is connected to the AV amplifier as shown

above, audio recorded in dts will not be output. To enjoy dts

sound, it is necessary to connect the player as shown on

page 10.

Direction of

signal flow

Video cable

(optional)

To component video input

connectors (Y, C

B, CR)

PCM/U DIGITAL

DTS

COAXIAL

AUDIO OUT

OPTICAL

SUBWOOFER

CENTER SURROUND

6CH DISCRETE

MIXED 2CH

VIDEO

MAIN

S VIDEO

VIDEO OUT

COMPONENT VIDEO

AC IN

CENTER

SUB

WOOFER

MAIN

SURROUND

AUDIO SIGNAL

DVD/LD

VIDEO SIGNAL

S-VIDEO

6CH DISCRETE INPUT DVD/LD

AV amplifier without

Dolby Digital/dts

decoder (optional)

S video cord

(optional)

In the case of the AV amplifier without

5.1ch input connectors

In the case of the AV amplifier

with 5.1ch input connectors

Getting Started

Remote control unit preparation

Battery installation A

Insert the batteries while observing the correct (o) and (p) po-

larities as illustrated at left.

Service life of batteries

ÁThe batteries normally last for about one year although this

depends on how often, and for what operations, the remote

control unit is used.

ÁIf the remote control unit fails to work, even when it is operat-

ed near the player, replace the batteries.

ÁUse size “AA” batteries.

Remote control operation range B

Point the remote control unit from no more than about 23 feet

(7 m) from the remote control sensor and within about 60u of

the front of the player.

ÁThe operating distance may vary according to the brightness

of the room.

Notes:

ÁDo not point bright lights at the remote control sensor.

ÁDo not place objects between the remote control unit and the

remote control sensor.

ÁDo not use this remote control unit while simultaneously op-

erating the remote control unit of any other equipment.

Connecting headphones C

Connect the headphones (optional).

ÁHeadphones with a

/4w (6.3 mm) stereo plug can be con-

nected.

Adjust the volume.

Caution:

Avoid listening to sound at levels which may be harmful to your

ears.

Notes:

ÁDo not use rechargeable (Ni-Cd) batteries.

ÁDo not attempt to recharge, short-circuit, disassemble,

heat or throw the batteries into a fire.

ÁDo not drop, step on or otherwise impact the remote

control unit. This may damage the parts or lead to mal-

function.

ÁDo not mix old and new batteries.

ÁIf the remote control unit is not going to be used for a

long time, remove the batteries. Otherwise, electrolyte

may leak which may lead, not only to malfunctioning

but also, to burns if contact is made with the electro-

lyte.

ÁWipe away any electrolyte leaking inside the remote

control unit, and install new batteries.

ÁIf any electrolyte should come into contact with parts of

your body, wash it off thoroughly with water.

Remote control signal sensor

23 feet (7 m)

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

NATURAL SOUND DVD PLAYER

SKIP

;

D I G I T A L

30˚ 30˚

STANDBY/ON

PHONES LEVEL

010

DVD / VIDEO CD /

NATURAL SOUND DVD PLAYER

LEVEL

010

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

POWER

*/ I

STOP

TITLE

RETURN

PLAY

OPEN/CLOSE

SKIP I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

NATURAL SOUND DVD PLAYER

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

SKIP

;

SKIP

;

D I G I T A L

Before enjoying DVD/Video CD/CD

The On-Screen menu language of your player has been

factory preset to English.

If you would like to change the menu language to

French or Spanish, please refer to “Selecting language

of On-Screen Display menu” on page 33.

In the explanations given below it is assumed that Eng-

lish has been selected as the menu language.

Basic play

Open

CloseReading

Preparations

ÁConfirm that the TV set or the audio equipment (if connected)

is properly connected to the player.

ÁConfirm that the power for the TV set or the audio equipment

(if connected) is turned on.

ÁConfirm that the input setting for the TV set or the audio

equipment (if connected) is properly selected.

(Example: Select “VCR 2” on the TV set if this player has

been connected to TV input connector [2].)

Basic play

Press POWER to switch on the power.

Press OPEN/CLOSE to

open the disc tray.

Place the disc on the disc tray with the label

side to be played facing upwards.

Hold the disc without touching either of its surfaces, posi-

tion it with the label side to be played facing upwards,

align it with the guides, and place it in its proper position.

e 3w (8 cm) disc

f 5w (12 cm) disc

Press PLAY.

The disc tray is automatically closed and play begins.

Basic Operation

ÁWhen the disc tray is closed by pressing OPEN/CLOSE,

press PLAY to start play.

ÁWhen a menu screen appears on the TV monitor

In case of an interactive DVD or

a Video CD with playback con-

trol, a menu screen appears on

the TV monitor. Perform step

5 to start play.

Press the cursor buttons (A, B, C, D) and

press SELECT, or press the numeric but-

tons, to select the preferred item.

ÁThe cursor buttons (A, B, C, D) are not effective for

selecting items for Video CDs.

Play of the selected item now begins.

While watching the movie program

ÁSetting to the picture quality best suited to movies

Using the On-Screen Menu Icon will select the optimum pic-

ture quality for movie programs (this setting gives a gentler

feel to videos, producing more detail in darker scenes and

helping to reduce noise).

The picture quality of your choice can be set using the On-

Screen Menu Icons. (See “Cinema Image” on page 21.)

ÁRaising the volume but only for the dialogue

The volume for the dialogue only can be raised by displaying

the On-Screen Menu Icons (for player information) and set-

ting “Cinema Dialogue” to “ON”. (See page 21.)

[This setting takes effect only for discs which are recorded

with Dolby Digital 5.1ch and with the sound contained in the

center channel.]

When the menu continues onto another screen

After step 4 on page 14, press SKIP (I).

ÁTo return to the previous menu screen

Press SKIP (H).

ÁDue to the design of some software titles, SKIP (H, I)

may not always work. For operation, refer also to the jacket

of the disc concerned.

Stopping play and returning to the menu

screen

Press TITLE, MENU or RETURN (for DVD), or RETURN (for

Video CD).

Play is suspended, and the menu screen is displayed.

ÁThe buttons may not work depending on the disc used.

What is playback control?

If a Video CD has “playback control” written on its disc or

jacket, it means that particular scenes or information can

be selected for viewing interactively with the TV monitor

using the menu screen.

(Example)

(Example of DVD)

Notes:

ÁThe disc continues to rotate while the menu is displayed

even after the player has finished playing a particular item.

When no further selections are to be played, be sure to press

STOP to clear the menu display.

ÁIf the disc is placed in upside down (and it is a single sided

disc), the FL display will indicate “NO PLAY”.

For your reference:

ÁWhen —— appears on the TV monitor while a button is be-

ing operated, it means that the corresponding operation is

prohibited by the player or the disc.

Stopping play

Press STOP during play.

RESUME function

The player records the point where STOP was pressed during

play (RESUME function). (“D” flashes on the player’s FL dis-

play when this function is activated.)

ÁPress PLAY again while “D” flashes, and play will resume

from this point.

ÁWhen the tray is opened or STOP is pressed again while “D”

flashes, the RESUME function will be cleared.

The RESUME function works only with titles for which the

elapsed playing time appears on the player’s FL display during

playback.

This feature will not be cleared when the player is set to the

standby mode and then turned back ON.

Chapter preview function (DVD only)

When PLAY is pressed while

“D” flashes, the message

shown at right is displayed.

When PLAY is pressed again while the above message is dis-

played, the first few seconds of each chapter from the begin-

ning of the title up to the point where operation was stopped

will be played. This makes it possible to review previously

viewed chapters. Normal playback will commence from the

point where operation was stopped.

Notes:

ÁCancelling the RESUME function will also clear the chapter

preview function.

ÁThe chapter preview function may not work with some DVDs.

After operation

When the player is not in use, remove the disc and press

POWER to set the player to the standby mode.

The player is automatically set to the standby mode after

30 minutes or so have elapsed in the stop mode.

(Auto power-off function)

TITLE MENU

Dogs

BirdsLovers

Castles

of the world

TITLE MENU

Birds

Dogs

Lovers

Castles

Press PLAY to Chapter Preview

Skipping ahead or back

Press SKIP (H, I) during play.

H: Reverse direction

I: Forward direction

For your reference:

ÁA chapter (DVD) or a track (Video CD/CD) is skipped each

time the button is pressed.

ÁWhen SKIP (H) is pressed once midway through a chap-

ter/track, play returns to the start of that chapter/track. When

it is pressed again, a chapter/track is skipped each time the

button is pressed.

ÁWhen SKIP (H, I) is pressed during menu play of Vid-

eo CDs with playback control, a menu screen may some-

times be recalled.

Still picture (Pause)

By the remote control unit

Press STILL/PAUSE during play.

By the main unit

Press PAUSE during play.

ÁDVD/Video CD: The player will be placed in the still picture

mode.

ÁCD: The player will be placed in the pause

mode.

ÁNormal play is resumed when PLAY is pressed.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

SELECT

STILL/PAUSE

PLAY

SKIP I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

POWER

NATURAL SOUND DVD PLAYER

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

SKIP

;

SKIP

;

D I G I T A L

STOP

Basic Operation

Rapid advance (Rapid reverse)

By the remote control unit

Press SLOW/SEARCH (F, G) during play.

On the main unit

Press SEARCH (F, G) during play.

ÁThe speed of advance (reverse) is relatively slow at first.

When the button is pressed again, the speed becomes fast-

er. (Each time the button is pressed, the speed increases up

to 5 steps.)

ÁThe speed will be retained even after the button is released.

ÁNormal play is resumed when PLAY is pressed.

For your reference:

ÁWhen SLOW/SEARCH (F, G) or SEARCH (F, G)

is used during menu play of Video CDs with playback control,

a menu screen may sometimes be recalled.

ÁFor DVD and Video CDs, audio from 6CH DISCRETE or

MIXED 2CH output connectors will be heard during rapid

advance scanning at the initial scan speed. (See page 42.)

Frame advance (Frame reverse)

[DVD/Video CD]

Press the cursor buttons (C, D) in the still pic-

ture mode.

(See page 16.)

C: Reverse direction

D: Forward direction

ÁThe disc is advanced (reversed) by one frame each time the

cursor button (C, D) is pressed.

ÁWhen the cursor button (C, D) is kept pressed, consecutive

frame advance (reverse) works.

ÁNormal play is resumed when PLAY is pressed.

Note:

ÁFor Video CDs, frame reverse is not possible.

For your reference:

ÁPressing STILL/PAUSE or PAUSE also activates frame ad-

vance.

ÁWhether the pictures are advanced by a “Frame” or “Field” is

automatic. (See page 42.)

Reverse

direction

Forward

direction

(Example)

Forward

direction

Reverse

direction

Slow-motion play [DVD/Video CD]

By the remote control unit

Press SLOW/SEARCH (F, G) in the still pic-

ture mode.

(See page 16.)

On the main unit

Press SEARCH (F, G) in the still picture

mode.

(See page 16.)

ÁThe speed of slow-motion is slow at first. When the button is

pressed again, the speed becomes faster. (Each time the

button is pressed, the speed increases up to 5 steps.)

ÁThe speed will be retained even after the button is released.

ÁNormal play is resumed when PLAY is pressed.

Note:

ÁFor Video CDs, slow-motion playback in reverse direction is

not possible.

Enjoying Video CDs with

playback control without using

menus [Video CD]

1. Press STOP after the menu screen appears (after step 4 on

page 14).

(“PBC” will be cleared from the player’s FL display.)

2. Press the numeric buttons to select the preferred track.

(Play begins.)

ÁRefer to the jacket etc. of the disc concerned for the track

numbers.

ÁPress “1” to start play from the beginning of the disc.

To return to menu play

Press STOP to stop playback and press MENU.

(“PBC” will light up on the player’s FL display and the menu

screen is resumed.)

Perform step 5 on page 15.

(Example)

Forward

direction

Reverse

direction

Forward

direction

Reverse

direction

SLOW/

1818

General information about On-

Screen Menu Icons

This player features On-Screen Menu Icons providing various

functions. A “banner” will be displayed on the TV monitor by

pressing the ON SCREEN button on the remote control.

Operating the cursor buttons/SELECT button on the remote

control will show disc information (title/chapter/track number,

elapsed playing time, audio/subtitle language, and angle) and

player information (repeat play, play mode, marker, etc.).

Some icons allow the settings to be changed.

Common procedures

Press ON SCREEN during play or in the

stop mode.

Each time this button is pressed, the TV monitor changes

as shown below.

[>On-Screen Menu Icons are not displayed

l>On-Screen Menu Icons for selecting disc information

l On-Screen Menu Icons for selecting player information

{=Shuttle screen

ÁSome functions cannot be accessed from the stop

mode.

Press the cursor buttons (C, D) to select

the preferred item.

ÁThe currently selected item is indicated by the yellow

frame on the On-Screen Menu Icons.

Press the cursor buttons (A, B) to select

the preferred setting.

ÁFor some functions, the setting will be registered imme-

diately; for others, SELECT or PLAY must be pressed.

ÁWhen numbers are displayed (e.g. title No.), the numeric

buttons are also effective for setting instead of the cursor

buttons (A, B). When numbers are entered by the nu-

meric buttons, press SELECT to register the setting.

Press RETURN or CLEAR to clear the On-Screen Menu

Icons.

Examples of On-Screen Menu Icons

(See A, B and C for detailed illustration.)

(The screens may differ depending on the disc contents.)

ÁDVD (A) ÁVideo CD (B) ÁCD (C)

For your reference:

ÁDepending on the type of DVD software and a TV with auto-

matic picture zoom function enabled, the On-Screen Menu

Icons may not be displayed or only partially displayed on the

TV screen.

In this case, change the position of the On-Screen Menu

Icons in “4 On-Screen Messages” of the initial settings.

(See page 34.)

ÁThe color (blue, violet or green) of the On-Screen Menu

Icons can be changed. (See page 34.)

1 1:56:37 1

LPCM

ENG

148k 16

OFF

ENG

3:37

L R

OFF

PBC

PRG

3:37

PRG

OFF

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

PLAY

CLEAR

SELECT

RETURN

ON SCREEN

OFF

Operation Using

On-Screen Menu Icons

Detailed descriptions of each On-Screen Menu Icon

Screen for disc information (For DVD)

Chapter No.

Change the chapter No. by using the cursor buttons (A, B) or the numeric buttons and

press SELECT.

Audio soundtrack

language No.

(See page 27.)

Audio soundtrack

language

LPCM

dts

Vocal

Change the No. by using the

cursor buttons (A, B) or the

numeric buttons.

ENG: English POR: Portuguese

FRA: French RUS Russian

DEU: German JPN: Japanese

ITA: Italian CHI: Chinese

ESP: Spanish KOR: Korean

NLD: Dutch MAL: Malay

SVE: Swedish VIE: Vietnamese

NOR: Norwegian THA: Thai

DAN: Danish U: Others

Linear PCM

(“k” stands for kHz

and “b” stands for bit.)

Dolby Digital

dts

DVD Karaoke (Solo)

DVD Karaoke (Duet)

16b

20b

24b

Audio

attribute

96k

48k

1–5.1ch

--- (OFF)

V1oV2

Change the No. by using the

cursor buttons (A, B) or the

numeric buttons.

ENG: English POR: Portuguese

FRA: French RUS Russian

DEU: German JPN: Japanese

ITA: Italian CHI: Chinese

ESP: Spanish KOR: Korean

NLD: Dutch MAL: Malay

SVE: Swedish VIE: Vietnamese

NOR: Norwegian THA: Thai

DAN: Danish U: Others

Select “ON” or “OFF” by using

the cursor buttons (A, B).

OFF Subtitle is cleared.

ON Subtitle is displayed.

Subtitle language No.

(See page 28.)

Subtitle language

Subtitle on/off

For your reference:

Á“Ô Õ” around the icon means that the item can be changed using the cursor buttons (A, B).

Title No. Change the title No. by using the cursor buttons (A, B) or the numeric buttons and press SELECT.

Angle No.

(See page 29.)

Change the No. by using the cursor buttons (A, B) or the

numeric buttons.

Elapsed playing time

(hour: minute: second)

Change the time by using the numeric buttons and press SELECT.

It can be used to find a specific scene quickly.

Example: To specify “1 hour 56 min. 37 sec.”, enter “15637”.

(This function does not work with some discs.)

2020

Playback control

(Video CD only)

(See page 15.)

OFF Menu play is not ON.

ON Menu play is ON.

Detailed descriptions of each On-Screen Menu Icon

Screen for disc information (For Video CD/CD)

Track No.

Change the track No. by using the cursor buttons

(A, B) or the numeric buttons and press SELECT.

Elapsed playing time

(minute: second)

During CD play, display is changed by using the cursor

buttons (A, B).

Elapsed playing time>

Remaining time of the track

^-----Remaining time of the disc(--}

Audio mode

(Video CD only)

(See page 27.)

Change the mode by using the cursor buttons (A, B).

Left channel sound is output from the speaker (L),

and right channel sound from the speaker (R).

Left channel sound only is output.

Right channel sound only is output.

Note:

ÁTrack No. and the elapsed playing time are not displayed during menu play of Video CDs with playback control.

ÁIt is not possible to turn playback control ON or OFF using the On-Screen Menu Icons.

For your reference:

Á“Ô Õ” around the icon means that the item can be changed using the cursor buttons (A, B).

Strona jest ładowana ...

Yamaha DVD-S795 Instrukcja obsługi

Marka: Yamaha

Model: DVD-S795

Kategoria: Odtwarzacze DVD

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

čeština: Yamaha DVD-S795 Návod k obsluze
español: Yamaha DVD-S795 El manual del propietario
italiano: Yamaha DVD-S795 Manuale del proprietario
Deutsch: Yamaha DVD-S795 Bedienungsanleitung
svenska: Yamaha DVD-S795 Bruksanvisning
português: Yamaha DVD-S795 Manual do proprietário
français: Yamaha DVD-S795 Le manuel du propriétaire
Türkçe: Yamaha DVD-S795 El kitabı
English: Yamaha DVD-S795 Owner's manual
dansk: Yamaha DVD-S795 Brugervejledning
русский: Yamaha DVD-S795 Инструкция по применению
Nederlands: Yamaha DVD-S795 de handleiding
română: Yamaha DVD-S795 Manualul proprietarului

Yamaha DVD-S795 Instrukcja obsługi

Yamaha DVD-S795 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty