Bestway 58259 Pool Heater Instrukcja obsługi

Marka: Bestway

Model: 58259 Pool Heater

Typ: Instrukcja obsługi

OWNER’S MANUAL

bestwaycorp.com/support

Visit Bestway YouTube channel

58259

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

Spare Parts, Please Visit

bestwaycorp.com/support

SAFETY INSTRUCTIONS

WARNING

When installing and using this electrical appliance, basic safety

precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL

INSTRUCTIONS

WARNING:

• The Pool Heater must be tested before each use. To test, follow the

instructions in the Operation section of this manual.

• The Pool Heater must be supplied through a residual current device

(RCD) having a rated residual operating current not exceeding 30mA.

• The power source on the wall of building should keep more than 4m

away from pool and at a height of 1.2m at least.

• Parts containing live parts, except parts supplied with safety extra-low

voltage not exceeding 12V, must be inaccessible to a person in the

pool; Parts incorporating electrical components, except remote control

devices, must be located or fixed so that they cannot fall into the

swimming pool.

• RISK OF ELECTRIC SHOCK - The Pool Heater can not be used while

people are inside the pool.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a

hazard.

• Extension cords can’t be used.

• Do not bury cord. Locate cord to minimize abuse from lawn mowers,

hedge trimmers, and other equipment.

• The Pool Heater should not be setup or left out in temperature lower

than 4°C (40°F).

• It is necessary to have the plug accessible after installation of the pool.

• Before using the Pool Heater, make sure the pool has been filled with

water.

• Pool Heaters are designed for used with specific water volume; ensure

your Pool Heater matches your pool’s water volume along with your

Filter Pump or Sand Filter’s designated water flow rate.

• RISK OF ELECTRIC SHOCK - Install at least 2m from all

metalsurfaces.

• The heater must be supplied by earthed power source.

• WARNING: Always keep plug dry, plug in with wet plug is

definitely forbidden!

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision. (For EU market)

• WARNING - This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance

by a person responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance. (For market other

than EU)

Cleaning and user maintenance must be performed by an adult above

18 years old who is familiar with the risk of electric shock.

Caution: Read the instruction before using the appliance and

installation/reassemble each time.

Warning: For electric safety, a PRCD device is incorporated in the

power cord, if the leakage current is detected more than 10mA,

the device will operate and cut-off the power supply, in such case,

please unplug and stop using the product at once. Don’t reset the

product by yourself. And you must contact the local service agent

to check and repair the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

- on raining days

- before cleaning or other maintenance

- Leave it unattended on holidays

When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• Safekeeping the instruction. For reconstruction the pool set every time,

please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

CAUTION:

• Pool Heater is for use with storable pools only. Do not use with

permanently-installed pools. A storable pool is constructed so that it is

capable of being readily disassembled for storage and reassembled to

its original integrity. A permanently-installed pool is constructed in or

on the ground or in a building such that it cannot be readily

disassembled for storage.

• Never add water to chemicals. Always add chemicals to water to avoid

strong fumes or violent reactions that may result in hazar ous chemical

spray.

Electric installations should follow national wiring rules, consult a

qualified electrician with any questions.

After using your heater for 3-5 years, you should contact your local

qualified maintenance technician to ensure the safety and

performance.

The main components, such as heating element, within the electric unit

should be checked and replaced(if necessary) by professional

persons.

NOTE:

• Handle the Pool Heater with care. Do not pull or carry the Pool Heater

by the power cord. Keep cords free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the Pool Heater.

• Please examine all equipment before use. Notify Bestway through our

customer service address listed on this manual for any damaged or

missing parts at the time of purchase. Verify all components represent

the model that you purchased.

• This product is not intended for commercial use.

IMPORTANT: Using the Pool Heater with an unmatched electrical

supply is dangerous and will result in catastrophic failure of the Pool

Heater.

SAVE THESE INSTRUCTIONS

PRCD WARNING

WARNING: The PRCD plug must be tested before each use to avoid

risk of electric shock.

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

Spare Parts, Please Visit

bestwaycorp.com/support

POOL HEATER

OWNER’S MANUAL

Visit Bestway YouTube

channel

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the pump.

WARNING: Do not use the heater if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

SAFETY INSTRUCTIONS

WARNING

When installing and using this electrical appliance, basic safety

precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL

INSTRUCTIONS

WARNING:

• The Pool Heater must be tested before each use. To test, follow the

instructions in the Operation section of this manual.

• The Pool Heater must be supplied through a residual current device

(RCD) having a rated residual operating current not exceeding 30mA.

• The power source on the wall of building should keep more than 4m

away from pool and at a height of 1.2m at least.

• Parts containing live parts, except parts supplied with safety extra-low

voltage not exceeding 12V, must be inaccessible to a person in the

pool; Parts incorporating electrical components, except remote control

devices, must be located or fixed so that they cannot fall into the

swimming pool.

• RISK OF ELECTRIC SHOCK - The Pool Heater can not be used while

people are inside the pool.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a

hazard.

• Extension cords can’t be used.

• Do not bury cord. Locate cord to minimize abuse from lawn mowers,

hedge trimmers, and other equipment.

• The Pool Heater should not be setup or left out in temperature lower

than 4°C (40°F).

• It is necessary to have the plug accessible after installation of the pool.

• Before using the Pool Heater, make sure the pool has been filled with

water.

• Pool Heaters are designed for used with specific water volume; ensure

your Pool Heater matches your pool’s water volume along with your

Filter Pump or Sand Filter’s designated water flow rate.

• RISK OF ELECTRIC SHOCK - Install at least 2m from all

metalsurfaces.

• The heater must be supplied by earthed power source.

• WARNING: Always keep plug dry, plug in with wet plug is

definitely forbidden!

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision. (For EU market)

• WARNING - This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance

by a person responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance. (For market other

than EU)

Cleaning and user maintenance must be performed by an adult above

18 years old who is familiar with the risk of electric shock.

Caution: Read the instruction before using the appliance and

installation/reassemble each time.

Warning: For electric safety, a PRCD device is incorporated in the

power cord, if the leakage current is detected more than 10mA,

the device will operate and cut-off the power supply, in such case,

please unplug and stop using the product at once. Don’t reset the

product by yourself. And you must contact the local service agent

to check and repair the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

- on raining days

- before cleaning or other maintenance

- Leave it unattended on holidays

When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• Safekeeping the instruction. For reconstruction the pool set every time,

please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

CAUTION:

• Pool Heater is for use with storable pools only. Do not use with

permanently-installed pools. A storable pool is constructed so that it is

capable of being readily disassembled for storage and reassembled to

its original integrity. A permanently-installed pool is constructed in or

on the ground or in a building such that it cannot be readily

disassembled for storage.

• Never add water to chemicals. Always add chemicals to water to avoid

strong fumes or violent reactions that may result in hazar ous chemical

spray.

Electric installations should follow national wiring rules, consult a

qualified electrician with any questions.

After using your heater for 3-5 years, you should contact your local

qualified maintenance technician to ensure the safety and

performance.

The main components, such as heating element, within the electric unit

should be checked and replaced(if necessary) by professional

persons.

NOTE:

• Handle the Pool Heater with care. Do not pull or carry the Pool Heater

by the power cord. Keep cords free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the Pool Heater.

• Please examine all equipment before use. Notify Bestway through our

customer service address listed on this manual for any damaged or

missing parts at the time of purchase. Verify all components represent

the model that you purchased.

• This product is not intended for commercial use.

IMPORTANT: Using the Pool Heater with an unmatched electrical

supply is dangerous and will result in catastrophic failure of the Pool

Heater.

SAVE THESE INSTRUCTIONS

PRCD WARNING

WARNING: The PRCD plug must be tested before each use to avoid

risk of electric shock.

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the pump.

WARNING: Do not use the heater if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

SAFETY INSTRUCTIONS

WARNING

When installing and using this electrical appliance, basic safety

precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL

INSTRUCTIONS

WARNING:

• The Pool Heater must be tested before each use. To test, follow the

instructions in the Operation section of this manual.

• The Pool Heater must be supplied through a residual current device

(RCD) having a rated residual operating current not exceeding 30mA.

• The power source on the wall of building should keep more than 4m

away from pool and at a height of 1.2m at least.

• Parts containing live parts, except parts supplied with safety extra-low

voltage not exceeding 12V, must be inaccessible to a person in the

pool; Parts incorporating electrical components, except remote control

devices, must be located or fixed so that they cannot fall into the

swimming pool.

• RISK OF ELECTRIC SHOCK - The Pool Heater can not be used while

people are inside the pool.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a

hazard.

• Extension cords can’t be used.

• Do not bury cord. Locate cord to minimize abuse from lawn mowers,

hedge trimmers, and other equipment.

• The Pool Heater should not be setup or left out in temperature lower

than 4°C (40°F).

• It is necessary to have the plug accessible after installation of the pool.

• Before using the Pool Heater, make sure the pool has been filled with

water.

• Pool Heaters are designed for used with specific water volume; ensure

your Pool Heater matches your pool’s water volume along with your

Filter Pump or Sand Filter’s designated water flow rate.

• RISK OF ELECTRIC SHOCK - Install at least 2m from all

metalsurfaces.

• The heater must be supplied by earthed power source.

• WARNING: Always keep plug dry, plug in with wet plug is

definitely forbidden!

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision. (For EU market)

• WARNING - This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance

by a person responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance. (For market other

than EU)

Cleaning and user maintenance must be performed by an adult above

18 years old who is familiar with the risk of electric shock.

Caution: Read the instruction before using the appliance and

installation/reassemble each time.

Warning: For electric safety, a PRCD device is incorporated in the

power cord, if the leakage current is detected more than 10mA,

the device will operate and cut-off the power supply, in such case,

please unplug and stop using the product at once. Don’t reset the

product by yourself. And you must contact the local service agent

to check and repair the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

- on raining days

- before cleaning or other maintenance

- Leave it unattended on holidays

When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• Safekeeping the instruction. For reconstruction the pool set every time,

please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

CAUTION:

• Pool Heater is for use with storable pools only. Do not use with

permanently-installed pools. A storable pool is constructed so that it is

capable of being readily disassembled for storage and reassembled to

its original integrity. A permanently-installed pool is constructed in or

on the ground or in a building such that it cannot be readily

disassembled for storage.

• Never add water to chemicals. Always add chemicals to water to avoid

strong fumes or violent reactions that may result in hazar ous chemical

spray.

Electric installations should follow national wiring rules, consult a

qualified electrician with any questions.

After using your heater for 3-5 years, you should contact your local

qualified maintenance technician to ensure the safety and

performance.

The main components, such as heating element, within the electric unit

should be checked and replaced(if necessary) by professional

persons.

NOTE:

• Handle the Pool Heater with care. Do not pull or carry the Pool Heater

by the power cord. Keep cords free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the Pool Heater.

• Please examine all equipment before use. Notify Bestway through our

customer service address listed on this manual for any damaged or

missing parts at the time of purchase. Verify all components represent

the model that you purchased.

• This product is not intended for commercial use.

IMPORTANT: Using the Pool Heater with an unmatched electrical

supply is dangerous and will result in catastrophic failure of the Pool

Heater.

SAVE THESE INSTRUCTIONS

PRCD WARNING

WARNING: The PRCD plug must be tested before each use to avoid

risk of electric shock.

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the pump.

WARNING: Do not use the heater if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local

authority or retailer for recycling advice.

DISPOSAL

PARTS REFERENCE OVERVIEW

Before assembling the Pool Heater become familiar with all parts.

REF. NO. DESCRIPTION QTY PART NO.

001

002

003

Pool Heater

Hose

Hose Clamp

58259ASS19

P6176ASS16

P6124ASS16

SPECIFICATIONS

Voltage:

Power:

Frequency:

Max. Heat Capability:

Increased Heat Rate (*):

Suitable Pool Water Volume:

Filter Pump/Sand Filter

Compatibility:

Pool Compatibility:

220-240V

2,800W at 20°C

50Hz

40°C

Approximately 0.5°C/h-1.5°C/h

depending on total water volume

400-4,500gal (1,520-17,035 L)

3,785 L/h (1,000 gal/h) and below

3,785 L/h (1,000 gal/h)

15’ and smaller

NOTE: The increased Heat Rate is just for reference. The actual

heating time may vary according to the pool’s water volume,

environmental temperatures, desired temperatures and other

conditions. Usually, if the pool has a large water volume or if

environment temperatures are low and the desired temperature

is high, longer heating time is required. However, if the

temperature increase is less than 0.2°C after one heating hour,

the water temperature can be thought to have reached the

highest balance temperature.

SAFETY INSTRUCTIONS

WARNING

When installing and using this electrical appliance, basic safety

precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL

INSTRUCTIONS

WARNING:

• The Pool Heater must be tested before each use. To test, follow the

instructions in the Operation section of this manual.

• The Pool Heater must be supplied through a residual current device

(RCD) having a rated residual operating current not exceeding 30mA.

• The power source on the wall of building should keep more than 4m

away from pool and at a height of 1.2m at least.

• Parts containing live parts, except parts supplied with safety extra-low

voltage not exceeding 12V, must be inaccessible to a person in the

pool; Parts incorporating electrical components, except remote control

devices, must be located or fixed so that they cannot fall into the

swimming pool.

• RISK OF ELECTRIC SHOCK - The Pool Heater can not be used while

people are inside the pool.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a

hazard.

• Extension cords can’t be used.

• Do not bury cord. Locate cord to minimize abuse from lawn mowers,

hedge trimmers, and other equipment.

• The Pool Heater should not be setup or left out in temperature lower

than 4°C (40°F).

• It is necessary to have the plug accessible after installation of the pool.

• Before using the Pool Heater, make sure the pool has been filled with

water.

• Pool Heaters are designed for used with specific water volume; ensure

your Pool Heater matches your pool’s water volume along with your

Filter Pump or Sand Filter’s designated water flow rate.

• RISK OF ELECTRIC SHOCK - Install at least 2m from all

metalsurfaces.

• The heater must be supplied by earthed power source.

• WARNING: Always keep plug dry, plug in with wet plug is

definitely forbidden!

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision. (For EU market)

• WARNING - This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance

by a person responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance. (For market other

than EU)

Cleaning and user maintenance must be performed by an adult above

18 years old who is familiar with the risk of electric shock.

Caution: Read the instruction before using the appliance and

installation/reassemble each time.

Warning: For electric safety, a PRCD device is incorporated in the

power cord, if the leakage current is detected more than 10mA,

the device will operate and cut-off the power supply, in such case,

please unplug and stop using the product at once. Don’t reset the

product by yourself. And you must contact the local service agent

to check and repair the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

- on raining days

- before cleaning or other maintenance

- Leave it unattended on holidays

When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

002

003

001

For assistance, please visit the support section on our

website, www.bestwaycorp.com

For assistance, please visit the support section on our

website, www.bestwaycorp.com

Refer to the filter pump or sand filter user’s manual.

For assistance, please visit the support section on our

website, www.bestwaycorp.com

The pool heater was not designed to operate with water

temperatures lower than 4ºC (39°F). Unplug the heater and

only re-start the heater when the water temperature reaches

6°C (43°F).

The pool heater was not designed to operate with water

temperatures higher than 50ºC (122°F). Unplug the heater

and only re-start the heater when the water temperature

reaches 38°C (100°F).

Alarms

Phenomenon Reasons Solutions

The temperature sensor does not work

Filter pump or sand filter does not operate, no water flow.

Water flow sensor broken.

The water temperature is lower than 4°C (39°F) .

The water temperature is higher than 50°C (122°F) .

The fuse is disconnected

1. Push the reset button, then check if the heater can work

normally.

2. In case the alarm still remains, check the RESET BUTTON

section in manual.

3. For assistance, please visit the support section on our

website, www.bestwaycorp.com

The manual reset thermal cut-out has been tripped

• Safekeeping the instruction. For reconstruction the pool set every time,

please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

CAUTION:

• Pool Heater is for use with storable pools only. Do not use with

permanently-installed pools. A storable pool is constructed so that it is

capable of being readily disassembled for storage and reassembled to

its original integrity. A permanently-installed pool is constructed in or

on the ground or in a building such that it cannot be readily

disassembled for storage.

• Never add water to chemicals. Always add chemicals to water to avoid

strong fumes or violent reactions that may result in hazar ous chemical

spray.

Electric installations should follow national wiring rules, consult a

qualified electrician with any questions.

After using your heater for 3-5 years, you should contact your local

qualified maintenance technician to ensure the safety and

performance.

The main components, such as heating element, within the electric unit

should be checked and replaced(if necessary) by professional

persons.

NOTE:

• Handle the Pool Heater with care. Do not pull or carry the Pool Heater

by the power cord. Keep cords free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the Pool Heater.

• Please examine all equipment before use. Notify Bestway through our

customer service address listed on this manual for any damaged or

missing parts at the time of purchase. Verify all components represent

the model that you purchased.

• This product is not intended for commercial use.

IMPORTANT: Using the Pool Heater with an unmatched electrical

supply is dangerous and will result in catastrophic failure of the Pool

Heater.

SAVE THESE INSTRUCTIONS

PRCD WARNING

WARNING: The PRCD plug must be tested before each use to avoid

risk of electric shock.

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the pump.

WARNING: Do not use the heater if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

Pedestal Fixing

The pool heater must be vertically fixed on ground or a certain pedestal made of wood or concrete before it can be used.

There should be two holes, 8mm in diameter on the pedestal, the space between which should be 254mm. Put the pool

heater on the pedestal and fix them together with bolts and nuts. The pedestal should weigh over 18kgs in order to

prevent the pool heater from accidentally falling.

254 MM

8 MM

Problem Cause

Troubleshooting

Solution

A. Power failure.

A. The Pool Heater is not working

B. Heating time is too long

C. Filter pump or Sand Filter does not match the Pool

Heater appropriately or Filter Pump or Sand Filter

failed, resulting in high or low water flow rates.

D. Pool Heater set-up failed

E. The thermal cut out cut off

F. Pool Heater failed

A. Hose Clamps are loose

B. Hose O-ring not in correct position

C. Hose Broken

A. Filter Pump or Sand Filter does not work

B. Filter Pump or Sand Filter broken

A. The light is broken.

A. Check power source.

A. Check the LED light to see whether the heater is working.

B. Highly recommend the use of a Bestway pool cover.

C. Replace the Filter Pump or Sand Filter following the

specification of this owner’s manual, and perform

maintenance according to the instructions of Filter Pump or

Sand Filter.

D. Reset-up the Pool Heater according to the instructions.

E. Press the “Reset” button on the Pool Heater.

F. For assistance, please visit the support section on our

website, www.bestwaycorp.com

A. Tighten the hose clamps

B. Check whether O-Ring are damaged.

C. Hose needs to be replaced

A. Reset-up the Filter Pump or Sand Filter according to the

instructions.

Check and repair the Filter Pump or Sand Filter according to

the relevant instructions in the Filter Pump or Sand Filter’s

owner’s manual.

A. The heating light is wrong and the heater still works.

1. The heating light does not work.

2. Pool Heater not heating properly.

3. Inlet and Outlet Valves leak.

4. Water does not flow.

The heating light turns off but the Pool

Heater heats.

ASSEMBLY

1. Set-up and fill the pool with water to the required level according to the

pool’s owner’s manual.

2. Attach the Filter Pump or Sand Filter’s Inlet Valve to the Pool:

a) Place the loose Hose Clamps on both ends of a Filter Pump or Sand

Filter Hose.

b) Attach the hose to Filter Pump or Sand Filter’s Inlet Valve and the

Pool’s Outlet Valve B.

c) Tighten the Hose Clamps.

3. Connect the Filter Pump or Sand Filter to the Pool Heater:

a) Place the loose Hose Clamps on both ends of the Pool Heater Hose.

b) Attach the hose to the Filter Pump or Sand Filter’s Outlet Valve and

the Pool Heater’s ‘INLET’ Valve and tighten the Hose Clamps.

4. Attach the Pool Heater to the Pool’s Inlet Valve A.

5. Loosen the Hose Clamps on the Pool’s Inlet and Outlet Valves; replace

the Stopper Plugs with Debris Screens. Water now flows to the Filter

Pump or Sand Filter and the Pool Heater. With the Hoses and the

Debris Screens in position, tighten the Hose Clamps.

6. Check that every port and valve is connected correctly.

POOL HEATER EQUIPOTENTIAL BONDING TERMINAL

It is recommended to arrange for a qualified electrician to connect the

Pool Heater to a equipotential bonding terminal using a (minimum)

2.5mm2 solid copper conductor.

PRCD TEST

RESET

TEST

RESET

TEST

RESET

TEST

RESET

TEST

RESET BUTTON

IMPORTANT INSTRUCTION FOR USING

If the water temperature has not changed 4-5 hours after activation of the heating system, use a thin object to press

the RESET BUTTON, and restart the heating system.

IMPORTANT: The heating system will not operate if the outside temperature is above 40°C (104°F) or if the Pool

Heater is under direct sunlight. Under these conditions, please wait until a cooler time of day before pressing the

RESET BUTTON with a thin object and restart the heating system.

NOTE: To order spare parts for the Pool Heater, please provide us with part no. and part name.

Drawings for illustration purposes only. May not reflect actual product. Not to scale.

RESET

P6124ASS16

Hose Clamp

P6176ASS16

Hose

P6005ASS16

O-Ring

Filter Pump

Above Ground Pool

Water Level

Sand Filter

P6124ASS16

Heating Reset

1. Be sure to press the "Reset" button on the

pool heater using a small and thin object before

initial operation

2. If the pool heater is not heating properly, press the "Reset"

button on the pool heater.

OPERATION

NOTE: Check the pool for correct installation and make sure both the pool’s

Inlet and Outlet Valves are fully covered with water before operating the Filter

Pump or Sand Filter with the Pool Heater. Make sure that the Pool Heater and

Filter Pump or Sand Filter are correctly connected.

1. Start the Filter Pump or Sand Filter according to the owner’s manual.

2. With the pump operating, insert the plug of the Pool Heater into a socket,

after test PRCD . The LED will light up for 0.5 seconds with a “beep” sound,

and the LED displays .

3. Press the “POWER” button for 2 seconds, the LED turns on and the heater

starts to work, the LED display .

4. Press the “POWER” button for 2 seconds again, the Pool Heater will turn off.

NOTE: When the water temperature reaches the maximum temperature

40°C (104°F), the LED turns green.

NOTE: Never plug in the Pool Heater until the Filter Pump or Sand Filter has

been plugged in.

WARNING: To prevent the risk of electrical shock, ensure your hands are

completely dry when plugging-in the Filter Pump or Sand Filter and the Pool

Heater.

NOTE: To prevent the risk of electrical shock, never run the Filter Pump or

Sand Filter and the Pool Heater when people are in the pool.

NOTE: Do not dry run the Pool Heater. Damage caused by dry running the

Pool Heater is not covered by the manufacturer’s warranty.

5. Remember to disconnect the Pool Heater first. Never unplug the Filter Pump

or Sand Filter when the Pool Heater is running.

6. Unplug the Filter Pump or Sand Filter and enjoy warm pool water!

MAINTENANCE

CAUTION: YOU MUST UNPLUG THE POOL HEATER FIRST, THEN

UNPLUG THE FILTER PUMP OR SAND FILTER BEFORE PREFORMING

MAINTENANCE OR SEVERE RISK OF INJURY OR DEATH EXISTS.

1. Stop Water Flowing to the Filter Pump or Sand Filter and the Pool Heater:

a) Disconnect the Pool Heater and THEN the Filter Pump or Sand Filter.

b) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses.

c) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet and

Outlet Valves.

d) Refer to the Filter Pump or Sand Filter ’s Owner’s Manual for information

on Filter Pump or Sand Filter maintenance.

2. After Filter Pump or Sand Filter maintenance, replace the Stopper Plugs with

the Debris Screens in the pool’s Inlet and Outlet Valves. Water will now flow

to the Filter Pump or Sand Filter and the Pool Heater.

3. Operate as outlined in the Operation section of this manual.

STORAGE

CAUTION: YOU MUST UNPLUG THE POOL HEATER AND THE FILTER

PUMP OR SAND FILTER BEFORE MAINTENANCE BEGINS OR SEVERE

RISK OF INJURY OR DEATH EXISTS.

To avoid damage, pool equipment must be winterized when temperatures are

lower than 4°C (40°F). Allowing water to freeze will damage the Pool Heater

and void the warranty.

NOTE: Do not leave the heater out in the open air for long periods of time.

When it is not in use, please clean and dry it and then store it in a cool, dry

place.

1. Follow the instructions previously outline to stop water flowing to the Filter

Pump or Sand Filter and the Pool Heater.

2. Detach all hoses.

3. Drain any water in the Pool Heater and clean all components thoroughly.

4. Put the Pool Heater in a cool, dry place, out of children’s reach.

NOTICE:

• The table above is for reference only. Data are relevant for a covered pool with water at 25 degrees Celsius on a clear day.

• Ambient air and water temperature has an effect on water heating efficiency.

Time to increase by 1

degree Celsius

Hours

Pool Size

(Bestway Above Ground Pools)

Fast SetTM Pools

Steel ProTM Oval Pools

Round

Frame Pools

Rectangular Frame Pools

Hydrium Oval Pool

Hydrium Pool

1.4

2.2

2.9

3.6

6.5

7.0

9.0

6.5

10.0

1.0

2.6

3.6

6.0

6.5

10.0

7.0

10.0

2.6

2.2

3.0

4.0

6.0

10.0

6.5

4.0

2.44m x 66cm (8' x 26")

2.74m x 76cm (9' x 30'')

3.05m x 76cm (10' x 30")

3.66m x 76cm (12' x 30")

3.66m x 91cm (12' x 36")

4.57m x 91cm (15' x 36")

4.57m x 1.07m (15' x 42")

4.57m x 1.22m (15' x 48")

4.88m x 3.05m x 1.07m (16' x 10' x 42")

5.49m x 3.66m x 1.22m (18' x 12' x 48")

6.10m x 3.66m x 1.22m (20' x 12' x 48")

2.44m x 51cm (8' x 20")

2.44m x 61cm (8' x 24")

3.05m x 76cm (10' x 30")

3.05m x 1.00m (10' x 39.5")

3.30m x 1.02m (130” x 40")

3.66m x 76cm (12' x 30")

3.66m x 1.00m (12' x 39.5")

3.66m x 1.22m (12' x 48")

4.27m x 1.22m (14' x 48")

4.57m x 91cm (15' x 36")

4.57m x 1.22m (15' x 48")

2.87m x 2.01m x 1.00m (113" x 79" x 39.5")

3.00m x 2.01m x 66cm (118" x 79" x 26")

4.00m x 2.11m x 81cm (157" x 83" x 32")

4.04m x 2.01m x 1.00m (159" x 79" x 39.5")

4.12m x 2.01m x 1.22m (162" x 79" x 48")

4.88m x 3.66m x 1.22m (16' x 12' x 48'')

3.66m x 1.22m (12' x 48'')

3.05m x 1.22m (10' x 48'')

OPERATING TIME TABLE

Time to

increase by

1 degree

Celsius

Hours

Water capacity

(Calculated at 90% for Frame

Pool and 80% for Fast Set &

Oval Pool)

Gallons Liters

1,890

3,750

5,680

7,500

9,460

11,350

13,250

17,035

1.0

2.5

3.0

4.0

6.0

7.0

8.0

10.0

500

1,000

1,500

2,000

2,500

3,000

3,500

4,500

AQUECEDOR PARA PISCINA

MANUAL DO USUÁRIO

INSTRUÇÕES DE SEGURANÇA

ATENÇÃO

Ao instalar e usar este equipamento elétrico devem ser tomadas algumas

precauções de segurança válidas, incluindo as que seguem:

INSTRUÇÕES DE SEGURANÇA IMPORTANTES LEIA E SIGA TODAS AS

INSTRUÇÕES

ATENÇÃO:

• O Aquecedor da Piscina deve ser testado antes de cada uso. Para testar siga as

instruções na secção Operação deste manual.

• O Aquecedor da Piscina deve ser fornecido por meio de um aparelho de corrente

resídua (RCD) com uma corrente operacional residual proporcionada não

superior a 30mA.

• A fonte de alimentação de parede do edifício deve estar a mais de 4m afastada

da piscina e a uma altura de pelo menos 1.2m.

• As partes contendo partes vivas, com exceção das partes fornecidas com uma

voltagem de segurança extremamente baixa, que não supera a voltagem de 12V,

não deve ser acessível por uma pessoa na piscina; As partes que incorporam

componentes elétricas, com exceção dos aparelhos de controle remoto, devem

ser localizadas ou fixas, assim não poderão cair dentro da piscina.

• RISCO DE CHOQUE ELÉTRICO - O aquecedor da piscina não pode ser usado

com pessoas dentro da piscina.

• Se o fio de alimentação estiver danificado ele deve ser substituído pelo

fabricante, seu agente de serviço ou por pessoas qualificadas de modo a evitar

um dano.

• É proibido o uso de extensões de alimentação.

• Não dobre o fio. Coloque o fio de modo a evitar danos causados por cortadores

de grama, aparadores e outros equipamentos.

• O Aquecedor de Piscina não deve ser configurado ou deixado no exterior a

temperaturas inferiores a 4°C (40°F).

• É necessário ter a tomada acessível após a instalação da piscina.

• Antes de usar o aquecedor da piscina, certifique-se que a piscina tenha sido

abastecida com água.

• Os aquecedores de piscina estão concebidos para serem utilizados com um

volume de água específico, certifique-se que o seu Aquecedor de Piscina se

adequa ao volume de água da sua piscina bem como ao fluxo de água nominal

da sua Bomba de Filtro ou Filtro de Areia.

• RISCO DE CHOQUE ELÉTRICO - Instale a pelo menos 2m da superfície de

metal.

• O aquecedor deve ser alimentado por uma fonte de alimentação com ligação a

terra.

• ATENÇÃO: Mantenha a ficha sempre seca, ligar uma ficha molhada é

completamente proibido!

• Este equipamento pode ser usado por crianças de 8 anos de idade e superior e

pessoas com capacidades físicas, sensoriais ou mentais reduzidas ou falta de

experiência e conhecimento caso estes recebam supervisão ou instrução sobre o

uso do equipamento de forma segura e compreendam os ricos envolvidos. As

crianças não devem brincar com o aparelho. A limpeza e manutenção não deve

ser realizada por crianças sem supervisão. (Para o mercado UE)

• ATENÇÃO - Este aparelho não está concebido para ser utilizado por pessoas

(incluindo crianças) com capacidades físicas, sensoriais ou mentais reduzidas ou

falta de experiência e conhecimento, salvo se providos de supervisão ou

instrução referente ao uso do aparelho por uma pessoa responsável pela sua

segurança. As crianças devem ser supervisionadas para garantir que não

brincam com o aparelho. (Para o mercado externo à UE)

A limpeza e manutenção devem ser realizadas por um adulto com idade superior

a 18 anos e que tenha consciência do risco de choque eléctrico.

Cuidado: leia as instruções antes de utilizar o aparelho e a cada instalação/nova

montagem.

Atenção: Para segurança eléctrica, está incorporado no cabo de

alimentação um PRCD, se a corrente de fuga detectada for superior a 10mA,

o dispositivo irá entrar em funcionamento e cortar a alimentação, nesse

caso, por favor desligue e pare de utilizar o produto imediatamente. Não

reinicie o produto sozinho. E deve contactar o agente local de manutenção

para verificar e reparar o produto.

• Não ligue ou desligue o equipamento com as mãos molhadas

• Desligue sempre o equipamento:

- Em dias chuvosos

- Antes de limpar ou realizar outro tipo de manutenção

- Deixe-o sem supervisão durante as férias

Quando o aparelho não for utilizado durante um longo período de tempo, como

no inverno, o conjunto de piscina deve ser desmontado e armazenado no interior.

• Instruções de armazenamento. Para reconstrução do conjunto de piscina em

cada situação consulte sempre as instruções.

• Caso as instruções estejam em falta, por favor contacte a Bestway ou procure-o

no website: www.bestwaycorp.com

CUIDADO

• Este aquecedor deve ser usado somente para piscinas desmontáveis.

Não use em piscinas permanentes. Uma piscina desmontável é construída para

ser desmontada para ser guardada e montada para uso normal. Uma piscina

permanente é construída no chão, em alvenaria, ou de modo tal que não possa

ser desmontada para armazenamento.

• Nunca adicione produtos químicos à água. Sempre adicione produtos químicos à

água para evitar fumos fortes ou reações violentas que podem resultar em

borrifações químicas perigosas.

As instalações eléctricas devem seguir as regras nacionais de cablagem,

consulte um electricista qualificado para quaisquer dúvidas.

Depois de utilizar o seu aquecedor por 3-5 anos, deve contactar o seu técnico de

manutenção qualificado local para assegurar a segurança e o desempenho. Os

componentes principais, como o elemento aquecedor, da unidade eléctrica

devem ser verificados e substituídos(se necessário) por um profissional.

NOTA:

• Manuseie o aquecedor da piscina com cuidado. Não puxe ou transporte o

aquecedor da piscina pelo cabo de alimentação. Mantenha os fios livres de

abrasão. Objetos pontiagudos, óleo, peças que se movem e calor não devem ser

expostos ao aquecedor de piscina.

• Por favor examine o equipamento antes do uso. Notifique sempre a Bestway por

meio do serviço de assistência ao cliente elencado neste manual para partes

danificadas ou em falta no momento da compra.

Verifique se todos os componentes representam o modelo comprado.

• Este produto não é destinado para uso comercial.

IMPORTANTE: Usar o aquecedor de piscina com uma aparelhagem

elétrica não correspondente é perigoso e pode resultar em falha

irreparável para o aquecedor.

GUARDAR ESTAS INSTRUÇÕES

AVISO PRCD

ATENÇÃO:

A tomada PRCD deve ser testada antes de cada utilização para evitar

o risco de choque eléctrico.

ATENÇÃO:

Antes de inserir a ficha numa tomada, certifique-se que a frequência

RECOMENDAMOS NÃO DEVOLVER

O PRODUTO PARA A LOJA

Dúvidas? Problemas?

Faltam peças?

Para FAQ, manuais, vídeos ou

peças de reposição, visite

bestwaycorp.com/support

Visite o canal da Bestway no

YouTube

da corrente da tomada é adequada à bomba.

ATENÇÃO:

Não use o aquecedor se este teste falhar, Para obter assistência,

visite a secção de apoio no nosso sítio da internet: www.bestwaycorp.com.